DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
❑ 33% Smaller than SOT-232 ❑ Pass Element is Only External Part ❑ No Sense Resistor required ❑ Auto-Adapt* to Pass Element ❑ Short Circuit Protection* ❑ UV & POR Supervisory Circuits ❑ 2.5s Auto Retry ❑ ±10V to ±72V Input Voltage Range ❑ 0.6mA Typical Operating Supply Current ❑ Built in Clamp for AC Path Turn On Glitch Typical Applications and Waveforms -48V GND GATE VPP VNN HV100 DC/DC Converter +5V COM IRF530 400µF General Description The HV100/HV101 are 3-pin hotswap controllers available in SOT-223 and MLP packages, which require no external compo- nents other than a pass element. The HV100/HV101 contain many of the features found in hotswap controllers with 8 pins or more, and which generally require many external components. These features include undervoltage (UV) detection circuits, power on reset (POR) supervisory circuits, inrush current limit- ing, short circuit protection, and auto-retry. In addition, the HV100/HV101 use a patent pending mechanism to sample and adapt to any pass element, resulting in consistent hotswap profiles without any programming. The only difference between the HV100 and the HV101 is the internally set undervoltage (UV) threshold.
Ordering Information
V435 K001VH6 K001VHX 001VH V415 K101VH6 K101VHX 101VH *Patents Pending 1IRF530 is a Trademark of International Rectifier Corporation 2MLP3x2 Package Version compared to 3mmx3mm SOT-23-6 Demo Kit Available 3-Pin Hotswap, Inrush Current Limiter Controllers (Negative Supply Rail)
Electrical Characteristics (-40°C < TA < +85°C unless otherwise noted) lobmySr etemaraPn iMp yTx aMs tinUs noitidnoC ylppuS VotdecnerefeR( PP )nip V NN egatloVylppuS2 7-V UV I NN tnerruCylppuS6 .00 .1A mV NN V84-= lortnoCVU VotdecnerefeR( NN )nip V LVU )woLothgiH(dlohserhTVU 034 38 3V 0 01VH 3.214 17 .51V 1 01VH V HVU siseretsyHVU 3V 0 01VH 1V 1 01VH tuptuOevirDetaG VotdecnerefeR( NN )nip V ETAG egatloVevirDetaGmumixaM0 12 14 1V RS ETAG etaRwelSlaitinI5 7.15 .25 2.3s m/VC ETAG Fn1= I NWODETAG )gniknis(tnerruCnwoD-lluPevirDetaG8 6 1A mV ETAG V;V1= PP V5.11= I PULLUP tnerruCpu-lluPpawStoHtsoP6 1 1A µV ETAG V6= lortnoCgnimiT VotdecnerefeR( NN )nip t ROP yaleDROPnoitresnI5 .15 .35 .5s m t DRA yaleDtratseRotuA5 2.15 .25 7.3s stluseRlacirtcelEelpmaxE )035FRIgnisU( I MIL pawstoHgniruDtnerruChsurnIxaM4 .1A C ,TEFSOMlanretxe035FRI DAOL Fµ001= I MIL pawstoHgniruDtnerruChsurnIxaM5 .2A C ,TEFSOMlanretxe035FRI DAOL Fµ002= I MIL pawstoHgniruDtnerruChsurnIxaM1 .3A C ,TEFSOMlanretxe035FRI DAOL Fµ003= I TROHS trohSaotnItnerruCxaM0 .4A R ,TEFSOMlanretxe035FRI DAOL 1<<= t TROHS emiTceteDdaoLdetrohS0 .1s mR ,TEFSOMlanretxe035FRI DAOL 1<<= ∆ ETAG etaGfoesiRfoetaRlaitinI5 .2s m/VC yna,TEFSOMlanretxe035FRI DAOL t SH egatloVetaGlluFotdoirePpawStoH5 .21s mC yna,TEFSOMlanretxe035FRI DAOL Pin Description VPP – Positive voltage supply input to the circuit. VNN – This pin is the Negative voltage power supply input to the circuit. GATE – This is the Gate Driver Output for the external N- Channel MOSFET. Absolute Maximum Ratings* VPP Input Voltage -0.3V to 75V Operating Ambient Temperature Range -40°C to +85°C Operating Junction Temperature Range -40°C to 125°C Storage Temperature Range -65 °C to 150°C *All voltages referenced to VNN . Pinouts 12 3 VNN GATE VPP Top View SOT-223 VPP GATE VNN Top View 3 pin MLP
Insertion into Hot Backplanes Telecom, data network and some computer applications require the ability to insert and remove circuit cards from systems without powering down the entire system. Since all circuit cards have some filter capacitance on the power rails, which is espe- cially true in circuit cards or network terminal equipment utilizing distributed power systems, the insertion can result in high inrush currents that can cause damage to connector and circuit cards and may result in unacceptable disturbances on the system backplane power rails. The HV100/HV101 are designed to facilitate the insertion and removal of these circuit cards or connection of terminal equip- ment by eliminating these inrush currents and powering up these circuits in a controlled manner after full connector insertion has been achieved. The HV100/HV101 are intended to provide this control function on the negative supply rail. Description of Operation On initial power application the high input voltage internal regu- lator seeks to provide a regulated supply for the internal circuitry. Until the proper internal voltage is achieved all circuits are held reset by the internal UVLO and the gate to source voltage of the external N-channel MOSFET is held off. Once the internal regulator voltage exceeds the UVLO threshold, the input undervoltage detection circuit (UV) senses the input voltage to confirm that it is above the internally programmed threshold. If at any time the input voltage falls below the UV threshold, all internal circuitry is reset and the GATE output is pulled down to V NN . UVLO detection works in conjunction with a power on reset (POR) timer of approximately 3.5ms to overcome contact bounce. Once the UVLO is satisfied the gate is held to VNN until a POR timer expires. Should the UV monitor toggle before the POR timer expires, the POR timer will be reset. This process will be repeated each time UVLO is satisfied until a full POR period has been achieved. After completion of a full POR period, the MOSFET gate Auto- Adapt operation begins. A reference current source is turned on which begins to charge an internal capacitor generating a ramp voltage which rises at a slew rate of 2.5 V/ms. This reference slew rate is used by a closed loop system to generate a GATE output current to drive the gate of the external N-channel MOSFET with a slew rate that matches the reference slew rate. Before the gate crosses a reference voltage, which is well below the V TH of industry standard MOSFETs, the pull-up current value is stored and the Auto-Adapt loop is opened. This stored pull-up current value is used to drive the gate during the remainder of the hot swap period. The result is a normalization with C ISS , which for most MOSFETs scales with CRSS . The MOSFET gate is charged with a current source until it reaches its turn on threshold and starts to charge the load capacitor. At this point the onset of the Miller Effect causes the effective capacitance looking into the gate to rise, and the current source charging the gate will have little effect on the gate voltage. The gate voltage remains essentially constant until the output capacitor is fully charged. At this point the voltage on the gate of the MOSFET continues to rise to a voltage level that guarantees full turn on of the MOSFET. It will remain in the full on state until an input under voltage condition is detected. If the circuit attempts turn on into a shorted load, then the Miller Effect will not occur. The gate voltage will continue to rise essentially at the same rate as the reference ramp indicating that a short circuit exists. This is detected by the control circuit and results in turning off the MOSFET initiating a 2.5 second delay, after which a normal restart is attempted. If at any time during the start up cycle or thereafter, the input voltage falls below the UV threshold the GATE output will be pulled down to V NN , turning off the N-channel MOSFET and all internal circuitry is reset. A normal restart sequence will be initiated once the input voltage rises above the UVLO threshold plus hysteresis.
Application Information
Hotswap controllers using a MOSFET as the pass element all include a capacitor divider from VPP to VNN through CLOAD , CRSS and CGS . In most competitive solutions a large external capacitor is added to the gate of the pass element to limit the voltage on the gate resulting from this divider. In those instances if a gate capacitor is not used the internal circuitry is not available to hold off the gate and therefore a fast rising voltage input will cause the pass element to turn on for a moment. This allows current spikes to pass through the MOSFET. The HV100/HV101 include a built-in clamp to ensure that this spurious current glitch does not occur. The built-in clamp will work for the time constants of most mechanical connectors. There may be applications, however, that have rise times that are much less than 1µs (100’s of ns). In these instances it may be necessary to add a capacitor from the MOSFET gate to source to clamp the gate and suppress this current spike. In these cases the current spike generally contains very little energy and does not cause damage even if a capacitor is not used at the gate. Auto-Adapt Operation The HV100/HV101 Auto-adapt mechanism provides an impor- tant function. It normalizes the hotswap period regardless of pass element or load capacitor for consistent hotswap results. By doing this it allows the novel short circuit mechanism to work because the mechanism requires a known time base. The above diagram illustrates the effectiveness of the auto- adapt mechanism. In this example three MOSFETs with different C ISS and RDSON values are used. The top waveform is the hotswap current, while the bottom waveform is the gate voltage. As can be seen, the hotswap period is normalized, the initial slope of the gate voltage is approximately 2.5V/ms regardless of the MOSFET, and the total hotswap period and peak currents are a function of a MOSFET type dependent constant multiplied by C LOAD . Typically if MOSFETs of the same type are used, the hotswap results will be extremely consistent. If different types are used they will usually exhibit minimal variation. Short Circuit Protection The HV100/HV101 provide short circuit protection by shutting down if the Miller Effect associated with hotswap does not occur. Specifically, if the output is shorted then the gate will rise without exhibiting a “flat response”. Due to the fact that we have normal- ized the hotswap period for any pass element, a timer can be used to detect if the gate voltage rises above a threshold within that time, indicating that a short exists. The diagram below shows a typical turn on sequence with the load shorted, resulting in a peak current of 4A. The maximum current that may occur during this period can be controlled by adding a resistor in series with the source of the MOSFET. The lower graph shows the same circuit with a 100mΩ resistor inserted between source and V NN . In this case the maximum current is 25% smaller. For most applications and pass elements, the HV100/HV101 provides adequate limiting of the maximum current to prevent damage without the need for any external components. The 2.5s delay of the auto-retry circuit provides time for the pass element to cool between attempts. 2A/div NTE66 is a trademark of NTE Electronics IRF530 is a trademark of International Rectifier Corporation IRF120M is a trademark of International Rectifier Corporation
1235 Bordeaux Drive, Sunnyvale, CA 94089
TEL: (408) 744-0100 • FAX: (408) 222-4895 www.supertex.com 08/26/02 rev.3b ©2002 Supertex Inc. All rights reserved. Unauthorized use or reproduction prohibited. Application Information, cont’d. Auto-Retry Not only does the HV100/HV101 provide short circuit protection in a 3-pin package, it also includes a 2.5s built in auto-restart timer. The HV100/HV101 will continuously try to turn on the system every 2.5s, providing sufficient time for the pass element to cool down after each attempt. Calculating Inrush Current As can be seen in the diagram below, for a standard pass element, the HV100/HV101 will normalize the hotswap time period against load capacitance. For this reason the current limit will increase with increasing value of the load capacitance. Inrush can be calculated from the following formula: IINRUSH(PEAK) = (CISS / CRSS) * 2.5e3 * CLOAD This is a surprisingly consistent result because for most MOSFETs of a particular type the ratio of CISS / CRSS is relatively constant (though notice from the plot that there is some variation) even while the absolute value of these and other quantities vary. Based on this, the inrush current will vary primarily with C LOAD . This makes designing with the HV100/HV101 particularly easy because once the pass element is chosen, the period is fixed and the inrush varies with C LOAD only. Programming the HV100/HV101 The HV100/HV101 require no external components other than a pass element to provide the functionality described thus far. In some applications it may be useful to use external components to adjust the maximum allowable inrush current, adjust UVLO, or to provide additional gate clamping if the supply rails have rise times below 1ms. All of the above are possible with a minimum number of external components. i) To adjust inrush current with an external component simply connect a capacitor (C FB ) from drain to gate of the MOSFET. The inrush calculation then becomes: IINRUSH = (CISS / (CRSS + CFB )) * 2.5e3 * CLOAD Note that a resistor (approximately 10KΩ) needs to be added in series with CFB to create a zero in the feedback loop and limit the spurious turn on which is now enhanced by the larger divider element. ii) To increase undervoltage lockout simply connect a Zener diode in series with the V PP pin. iii) If the VPP rises particularly fast (>48e6V/s) then it may be desirable to connect a capacitor from gate to source of the MOSFET to provide a path for the power application tran- sient spike, which is now too fast for the internal clamping mechanism. iv) To limit the peak current during a short circuit, a resistor in series with the source of the MOSFET may help. Implementing PWRGD Control Due to the HV100/HV101’s small footprint, it is possible to create an open drain PWRGD signal using external components and still maintain a size comparable with the smallest hotswap controllers available elsewhere. To accomplish this an external MOSFET may be used in conjunction with the gate output. Simply use a high impedance divider (10MΩ) sized so that the open drain PWRGD MOSFET threshold will only be reached once the HV100/HV101’s gate voltage rises well above the current limit value required by the external MOSFET pass device. Alternatively a Zener diode between the gate output and the PWRGD MOSFET gate set at a voltage higher than the maximum pass element Vt will also work. 2A/div HV100 PWGRD