D946GZTS INTEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 88

Technical content

Datasheet sections

  • 1 Product Description
  • 1.1 Overview
  • 1.1.1 Feature Summary
  • 1.1.2 Board Layout
  • 1.1.3 Block Diagram
  • 1.2 Online Support
  • 1.3 Processor
  • 1.4 System Memory
  • 1.4.1 Memory Configurations
  • 1.5 Intel® 946GZ Express Chipset
  • 1.5.1 Intel 946GZ Graphics Subsystem
  • 1.5.2 USB
  • 1.5.3 Serial ATA Interfaces
  • 1.5.4 Parallel IDE Interface
  • 1.5.5 Real-Time Clock, CMOS SRAM, and Battery
  • 1.6 Legacy I/O Controller
  • 1.6.1 Serial Port
  • 1.6.2 Parallel Port
  • 1.6.3 Diskette Drive Controller
  • 1.6.4 Keyboard and Mouse Interface
  • 1.7 Audio Subsystem
  • 1.7.1 Audio Subsystem Software
  • 1.7.2 Audio Connectors and Headers
  • 1.8 LAN Subsystem
  • 1.8.1 Intel® 82562G PLC Device
  • 1.8.2 LAN Subsystem Software
  • 1.8.3 RJ-45 LAN Connector with Integrated LEDs
  • 1.9 Hardware Management Subsystem
  • 1.9.1 Hardware Monitoring and Fan Control
  • 1.9.2 Fan Monitoring
  • 1.9.3 Chassis Intrusion and Detection
  • 1.9.4 Thermal Monitoring
  • 1.10 Power Management
  • 1.10.1 ACPI
  • 1.10.2 Hardware Support
  • 2 Technical Reference
  • 2.1 Memory Map
  • 2.1.1 Addressable Memory
  • 2.2 DMA Channels
  • 2.3 Fixed I/O Map
  • 2.4 PCI Configuration Space Map
  • 2.5 Interrupts

Datasheet sections

  • 5 Regulatory Compliance and Battery Disposal Information
  • 5.1 Regulatory Compliance
  • 5.1.1 Safety Regulations
  • 5.1.2 European Union Declaration of Conformity Statement
  • 5.1.3 Product Ecology Statements
  • 5.1.4 EMC Regulations
  • 5.1.5 Product Certification Markings (Board Level)
  • 5.2 Battery Disposal Information

Order Number: D56026-001US The Intel® Desktop Board D946GZTS may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D946GZTS Specification Update. Intel® Desktop Board D946GZTS Technical Product Specification

Revision History

Revision Revision History Date -001 First release of the Intel ® Desktop Board D946GZTS Technical Product Specification. August 2006 This product specification applies to only the standard Intel® Desktop Board D946GZTS with BIOS identifier TS94610J.86A. Changes to this specification will be published in the Intel Desktop Board D946GZTS Specification Update before being incorporated into a revision of this document. INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. INTEL PRODUCTS ARE NOT INTENDED FOR USE IN MEDICAL, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Intel ® desktop boards may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from: Intel Corporation P.O. Box 5937 Denver, CO 80217-9808 or call in North America 1-800-548-4725, Europe 44-0-1793-431-155, France 44-0-1793-421-777, Germany 44-0-1793-421-333, other Countries 708-296-9333. Intel, the Intel logo, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. * Other names and brands may be claimed as the property of others. Copyright © 2006, Intel Corporation. All rights reserved.

This Technical Product Specification (TPS) specifies the board layout, components, connectors, power and environmental requirements, and the BIOS for the Intel® Desktop Board D946GZTS. It describes the standard product and available manufacturing options. Intended Audience The TPS is intended to provide detailed, technical information about the Desktop Board D946GZTS and its components to the vendors, system integrators, and other engineers and technicians who need this level of information. It is specifically not intended for general audiences. What This Document Contains Chapter Description

1 A description of the hardware used on the board

2 A map of the resources of the board

3 The features supported by the BIOS Setup program

4 A description of the BIOS error me ssages, beep codes, and POST codes

5 Regulatory compliance and battery disposal information

This section contains information about the conventions used in this specification. Not all of these symbols and abbreviations appear in all specifications of this type. Notes, Cautions, and Warnings NOTE Notes call attention to important information. # INTEGRATOR’S NOTES Integrator’s notes are used to call attention to information that may be useful to system integrators. CAUTION Cautions are included to help you avoid damaging hardware or losing data.

Intel Desktop Board D946GZTS Technical Product Specification iv Other Common Notation # Used after a signal name to identify an active-low signal (such as USBP0#) GB Gigabyte (1,073,741,824 bytes) GB/sec Gigabytes per second Gbit Gigabit (1,073,741,824 bits) KB Kilobyte (1024 bytes) Kbit Kilobit (1024 bits) kbits/sec 1000 bits per second MB Megabyte (1,048,576 bytes) MB/sec Megabytes per second Mbit Megabit (1,048,576 bits) Mbit/sec Megabits per second xxh An address or data value ending with a lowercase h indicates a hexadecimal value. x.x V Volts. Voltages are DC unless otherwise specified. * This symbol is used to indicate third-party brands and names that are the property of their respective owners.

Intel Desktop Board D946GZTS Technical Product Specification vi

3 Overview of BIOS Features

4 Error Messages and Beep Codes

Intel Desktop Board D946GZTS Technical Product Specification viii

1 Product Description

What This Chapter Contains

1.1 Overview

1.1.1 Feature Summary

Table 1 summarizes the major features of the Desktop Board D946GZTS. Table 1. Feature Summary

  • Intel® Core™2 Duo processor in an LGA775 socket with a 1066 or 800 MHz system bus
  • Intel® Pentium® D processor in an LGA775 socket with an 800 or 533 MHz system bus
  • Intel® Pentium® 4 processor in an LGA775 socket with an 800 or 533 MHz system bus
  • Intel® Celeron® D processor in an LGA775 socket with a 533 MHz system bus Memory • Two 240-pin DDR2 SDRAM Dual Inline Memory Module (DIMM) sockets
  • Support for DDR2 667 or DDR2 533 MHz DIMMs
  • Support for up to 4 GB of system memory Chipset Intel® 946GZ Express Chipset, consisting of:
  • Intel® 82946GZ Graphics and Memory Controller Hub (GMCH)
  • Intel® 82801GB I/O Controller Hub (ICH7) Video Intel® GMA 3000 onboard graphics subsystem Audio 6-channel (5.1) audio subsystem using the ADI1988A (or SigmaTel* STAC9227) audio codec Legacy I/O Control Legacy I/O controller for diskette drive, serial, parallel, and PS/2* ports USB Support for USB 2.0 devices Peripheral Interfaces
  • Eight USB ports
  • Four Serial ATA IDE interfaces
  • One Parallel ATA IDE interface with UDMA 33, ATA-66/100 support
  • One diskette drive interface
  • One serial port
  • One parallel port LAN Support 10/100 Mbits/sec LAN subsystem using the Intel® 82562G Platform LAN Connect (PLC) device BIOS • Intel® BIOS (resident in the SPI Flash device)
  • Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and SMBIOS Instantly Available PC Technology
  • Support for PCI Local Bus Specification Revision 2.3
  • Support for PCI Express* Revision 1.0a
  • Suspend to RAM support
  • Wake on PCI, RS-232, front panel, PS/2 devices, and USB ports continued

Table 1. Feature Summary (continued)

  • One PCI Express x16 bus add-in card connector
  • One PCI Express x1 bus add-in card connector
  • Two PCI Conventional* bus connectors Hardware Monitor Subsystem
  • Voltage sense to detect out of range power supply voltages
  • Thermal sense to detect out of range thermal values
  • Three fan headers
  • Three fan sense inputs used to monitor fan activity For information about Refer to Available configurations for the Desktop Board D946GZTS Section 1.2, page 15

1.1.2 Board Layout

Figure 1 shows the location of the major components. Figure 1. Major Board Components Table 2 lists the components identified in Figure 1.

Table 2. Board Components Shown in Figure 1

Description

B Chassis intrusion header C Front panel USB headers [2] D Serial ATA connectors [4] E Main Power connector F PCI Express x16 connector G PCI Express x1 connector H PCI Conventional bus add-in card connectors [2] I BIOS Setup configuration jumper block J Diskette drive connector K Front panel header L Front chassis fan header M Auxiliary front panel power LED header N Speaker O Intel 82801GB I/O Controller Hub (ICH7) P LGA775 processor socket Q Intel 82946GZ GMCH R Processor core power connector S Processor fan header T DIMM Channel A socket U DIMM Channel B socket V Rear chassis fan header W Battery X Parallel ATE IDE connector Y High Definition Audio Link header Z Front panel audio header

1.1.3 Block Diagram

Figure 2 is a block diagram of the major functional areas. Figure 2. Block Diagram

1.2 Online Support

To find information about… Visit this World Wide Web site: Intel® Desktop Board D946GZTS under “Desktop Board Products” or “Desktop Board Support” http://www.intel.com/design/motherbd http://support.intel.com/support/motherboards/desktop Available configurations for the Desktop Board D946GZTS http://developer.intel.com/design/motherbd/ts/ts_available.htm Processor data sheets http://www.intel.com/products/index.htm ICH7 addressing http://developer.intel.com/design/chipsets/datashts Audio software and utilities http://www.intel.com/design/motherbd LAN software and drivers http://www.intel.com/design/motherbd Supported video modes http://www.intel.com/design/motherbd/ts/ts_documentation.htm

1.3 Processor

The board is designed to support the following processors:

  • Intel Core 2 Duo processor in an LGA775 socket with a 1066 or 800 MHz system bus
  • Intel Pentium D processor in an LGA775 processor socket with an 800 or 533 MHz system bus
  • Intel Pentium 4 processor in an LGA775 processor socket with an 800 or 533 MHz system bus
  • Intel Celeron D processor in an LGA775 processor socket with a 533 MHz system bus See the Intel web site listed below for the most up-to-date list of supported processors. For information about… Refer to: Supported processors http://www.intel.com/design/motherbd/ts/ts_proc.htm CAUTION Use only the processors listed on web site above. Use of unsupported processors can damage the board, the processor, and the power supply. # INTEGRATOR’S NOTE Use only ATX12V-compliant power supplies. For information about Refer to Power supply connectors Section 2.7.2.2, page 50

1.4 System Memory

  • 1.8 V (only) DDR2 SDRAM DIMMs with gold-plated contacts
  • Unbuffered, single-sided or double-sided DIMMs with the following restriction: Double-sided DIMMS with x16 organization are not supported.
  • 4 GB maximum total system memory. Refer to Section 2.1.1 on page 37 for information on the total amount of addressable memory.
  • Minimum total system memory: 512 MB
  • Non-ECC DIMMs
  • Serial Presence Detect
  • DDR2 667 or DDR2 533 MHz SDRAM DIMMs NOTE A minimum of 512 MB of system memory is required to fully enable both the onboard graphics and the manageability engine. NOTE To be fully compliant with all applicable DDR SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability may be impacted or the DIMMs may not function under the determined frequency. Table 3 lists the supported DIMM configurations.

Table 3. Supported Memory Configurations

combination of DIMMs and processors. Table 4. Memory Operating Frequencies

1.4.1 Memory Configurations

  • Dual channel (Interleaved) mode. This mode offers the highest throughput for real world applications. Dual channel mode is enabled when the installed memory capacities of both DIMM channels are equal. Technology and device width can vary from one channel to the other but the installed memory capacity for each channel must be equal. If different speed DIMMs are used between channels, the slowest memory timing will be used.
  • Single channel (Asymmetric) mode. This mode is equivalent to single channel bandwidth operation for real world applications. This mode is used when only a single DIMM is installed or the memory capacities are unequal. Technology and device width can vary from one channel to the other. If different speed DIMMs are used between channels, the slowest memory timing will be used. Figure 3 illustrates the memory channel and DIMM configuration. OM18456 Channel A, DIMM 0 Channel B, DIMM 0

Figure 3. Memory Channel and DIMM Configuration

1.4.1.1 Dual Channel (Interleaved) Mode Configuration

DIMM sockets are populated with identical DIMMs. Figure 4. Dual Channel (Interleaved) Mode Configuration with Two DIMMs

1.4.1.2 Single Channel (Asymmetric) Mode Configurations

Channel A is populated. Channel B is not populated. Figure 5. Single Channel (Asymmetric) Mode Configuration with One DIMM Figure 6. Single Channel (Asymmetric) Mode Configuration with Two DIMMs

Intel Desktop Board D946GZTS Technical Product Specification

1.5 Intel® 946GZ Express Chipset

The Intel 946GZ Express chipset consists of the following devices:

  • Intel 82946GZ Graphics and Memory Controller Hub (GMCH) with Direct Media Interface (DMI) interconnect
  • Intel 82801GB I/O Controller Hub (ICH7) with DMI interconnect The GMCH component provides interfaces to the CPU, memory, PCI Express, and the DMI interconnect. The component also provides integrated graphics capabilities supporting 3D, 2D and display capabilities. The ICH7 is a centralized controller for the board’s I/O paths. For information about Refer to The Intel 946GZ Express chipset http://developer.intel.com/ Resources used by the chipset Chapter 2

1.5.1 Intel 946GZ Graphics Subsystem

The Intel 946GZ Express chipset contains two separate, mutually exclusive graphics options. Either the GMA 3000 graphics controller (contained within the 82946GZ GMCH) is used, or a PCI Express x16 add-in card can be used. When a PCI Express x16 add-in card is installed, the GMA 3000 graphics controller is disabled.

1.5.1.1 Intel® GMA 3000 Graphics Controller

The Intel GMA 3000 graphics controller features the following:

  • 667 MHz core frequency
  • High performance 3-D setup and render engine
  • High quality texture engine ⎯ DX9*/DX10 Compliant Hardware Shader Model 3.0 ⎯ 32-bit full precision floating point operations ⎯ 128-bit floating point texture formats ⎯ Alpha and luminance maps ⎯ Texture color-keying/chroma-keying ⎯ Cubic environment reflection mapping ⎯ Enhanced texture blending functions
  • 3D Graphics rendering enhancements ⎯ 1.3 dual texture GigaPixel/sec fill rate ⎯ 16 and 32 bit color ⎯ Maximum 3D supported resolution of 1600 x 1200 x 32 at 60 Hz ⎯ Vertex cache ⎯ Anti-aliased lines ⎯ OpenGL* version 1.5 support with vertex buffer and EXT_Shadow extensions
  • 2D Graphics enhancements ⎯ 8, 16, and 32 bit color ⎯ Optimized 256-bit BLT engine ⎯ Color space conversion ⎯ Anti-aliased lines
  • Video ⎯ Hardware motion compensation and iDCT for MPEG2 ⎯ Software DVD at 30 fps full screen
  • Display ⎯ Integrated 24-bit 400 MHz RAMDAC ⎯ Up to 2048 x 1536 at 75 Hz refresh (QXGA) ⎯ DDC2B compliant interface with Advanced Digital Display 2 or 2+ card (ADD2/ADD2+), support for TV-out/TV-in and DVI digital display connections ⎯ Supports flat panels up to 2048 x 1536 at 75 Hz (when in dual-channel mode) or digital CRT/HDTV at 1920 x 1080 at 85 Hz (with ADD2/MEC) ⎯ Two multiplexed SDVO port interfaces with 270 MHz pixel clocks using an ADD2/MEC card
  • Dynamic Video Memory Technology (DVMT) support up to 256 MB
  • Intel® Zoom Utility

1.5.1.2 Dynamic Video Memory Technology (DVMT)

DVMT enables enhanced graphics and memory performance through highly efficient memory utilization. DVMT ensures the most efficient use of available system memory for maximum 2-D/3-D graphics performance. Up to 256 MB of system memory can be allocated to DVMT on systems that have 512 MB or more of total system memory installed. DVMT returns system memory back to the operating system when the additional system memory is no longer required by the graphics subsystem. DVMT will always use a minimal fixed portion of system physical memory (as set in the BIOS Setup program) for compatibility with legacy applications. An example of this would be when using VGA graphics under DOS. Once loaded, the operating system and graphics drivers allocate additional system memory to the graphics buffer as needed for performing graphics functions. NOTE The use of DVMT requires operating system driver support.

Intel Desktop Board D946GZTS Technical Product Specification

1.5.1.3 Configuration Modes

A list of supported modes for the Intel GMA 3000 graphics controller is available as a downloadable document. For information about Refer to Supported video modes for the board Section 1.2, page 15

1.5.1.4 Advanced Digital Display (ADD2/ADD2+) Card Support

The GMCH routes two multiplexed SDVO ports that are each capable of driving up to a 200 MHz pixel clock to the PCI Express x16 connector. The SDVO ports can be paired for a dual channel configuration to support up to a 400 MHz pixel clock. When an ADD2/ADD2+ card is detected, the Intel GMA 3000 graphics controller is enabled and the PCI Express x16 connector is configured for SDVO mode. SDVO mode enables the SDVO ports to be accessed by the ADD2/ADD2+ card. An ADD2/ADD2+ card can either be configured to support simultaneous display with the primary VGA display or can be configured to support dual independent display as an extended desktop configuration with different color depths and resolutions. ADD2/ADD2+ cards can be designed to support the following configurations:

  • TV-Out (composite video)
  • Transition Minimized Differential Signaling (TMDS) for DVI 1.0
  • Low Voltage Differential Signaling (LVDS)
  • Single device operating in dual channel mode
  • VGA output
  • HDTV output
  • HDMI/UDI support (when used with the HD Audio Link)

1.5.2 USB

The board supports up to eight USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCI-compatible drivers. The ICH7 provides the USB controller for all ports. The port arrangement is as follows:

  • Four ports are implemented with stacked back panel connectors
  • Four ports are routed to two separate front panel USB headers NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. For information about Refer to The location of the USB connectors on the back panel Figure 13, page 45 The location of the front panel USB headers Figure 14, page 46

1.5.3 Serial ATA Interfaces

The board provides four Serial ATA (SATA) connectors, which support one device per connector.

1.5.3.1 Serial ATA Support

The ICH7’s Serial ATA controller offers four independent Serial ATA ports with a theoretical maximum transfer rate of 3 Gbits/sec per port. One device can be installed on each port for a maximum of four Serial ATA devices. A point-to-point interface is used for host to device connections, unlike Parallel ATA IDE which supports a master/slave configuration and two devices per channel. For compatibility, the underlying Serial ATA functionality is transparent to the operating system. The Serial ATA controller can operate in both legacy and native modes. In legacy mode, standard IDE I/O and IRQ resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering is used. Native mode is the preferred mode for configurations using the Windows* XP and Windows 2000 operating systems. NOTE Many Serial ATA drives use new low-voltage power connectors and require adaptors or power supplies equipped with low-voltage power connectors. For more information, see: http://www.serialata.org/. For information about Refer to The location of the Serial ATA connectors Figure 14, page 46

Intel Desktop Board D946GZTS Technical Product Specification

1.5.4 Parallel IDE Interface

The Parallel ATA IDE controller has one bus-mastering Parallel ATA IDE interface. The Parallel ATA IDE interface supports the following modes:

  • Programmed I/O (PIO): processor controls data transfer.
  • 8237-style DMA: DMA offloads the processor, supporting transfer rates of up to 16 MB/sec.
  • Ultra DMA: DMA protocol on IDE bus supporting host and target throttling and transfer rates of up to 33 MB/sec.
  • ATA-66: DMA protocol on IDE bus supporting host and target throttling and transfer rates of up to 66 MB/sec. ATA-66 protocol is similar to Ultra DMA and is device driver compatible.
  • ATA-100: DMA protocol on IDE bus allows host and target throttling. The ATA-100 logic can achieve read transfer rates up to 100 MB/sec and write transfer rates up to 88 MB/sec. NOTE ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce reflections, noise, and inductive coupling. The Parallel ATA IDE interface also supports ATAPI devices (such as CD-ROM drives) and ATA devices. The BIOS supports Logical Block Addressing (LBA) and Extended Cylinder Head Sector (ECHS) translation modes. The drive reports the transfer rate and translation mode to the BIOS. For information about Refer to The location of the Parallel ATA IDE connector Figure 14, page 46

1.5.5 Real-Time Clock, CMOS SRAM, and Battery

A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied. NOTE If the battery and AC power fail, custom defaults, if previously saved, will be loaded into CMOS RAM at power-on. When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 1 on page 12 shows the location of the battery.

1.6 Legacy I/O Controller

The I/O controller provides the following features:

  • One serial port
  • One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support
  • Serial IRQ interface compatible with serialized IRQ support for PCI systems
  • PS/2-style mouse and keyboard interfaces
  • Interface for one 1.44 MB or 2.88 MB diskette drive
  • Intelligent power management, including a programmable wake-up event interface
  • PCI power management support The BIOS Setup program provides configuration options for the I/O controller.

1.6.1 Serial Port

The board has one serial port connector located on the back panel. The serial port supports data transfers at speeds up to 115.2 kbits/sec with BIOS support. For information about Refer to The location of the serial port connector Figure 13, page 45

1.6.2 Parallel Port

The 25-pin D-Sub parallel port connector is located on the back panel. Use the BIOS Setup program to set the parallel port mode. For information about Refer to The location of the parallel port connector Figure 13, page 45

1.6.3 Diskette Drive Controller

The I/O controller supports one diskette drive. Use the BIOS Setup program to configure the diskette drive interface. For information about Refer to The location of the diskette drive connector Figure 14, page 46

1.6.4 Keyboard and Mouse Interface

The PS/2 keyboard and mouse connectors are located on the back panel. NOTE The keyboard is supported in the bottom PS/2 connector and the mouse is supported in the top PS/2 connector. Power to the computer should be turned off before a keyboard or mouse is connected or disconnected. For information about Refer to The location of the keyboard and mouse connectors Figure 13, page 45

1.7 Audio Subsystem

  • Intel 82801GB ICH7
  • Analog Devices ADI1988A (or Sigmatel STAC9227) audio codec
  • Back panel audio connectors
  • Component-side audio headers The audio subsystem supports the following features:
  • Advanced jack sense for the back panel audio jacks that enables the audio codec to recognize the device that is connected to an audio port. Within hardware constraints, the back panel audio jacks are capable of retasking according to the user’s definition, or can be automatically switched depending on the recognized device type.
  • Stereo input and output for all back panel jacks
  • Line out and Mic in functions for front panel audio jacks
  • A signal-to-noise (S/N) ratio of 95 dB Figure 7 is a block diagram of the audio subsystem. 82801GB I/O Controller Hub (ICH7) OM18389 Intel High Definition Audio Link Audio Codec Line Out/Retasking Jack Mic In Line In/Retasking Jack Mic In/Retasking Jack Line Out Back Panel Front Panel High Definition Audio Link Connector

Figure 7. 6-Channel (5.1) Audio Subsystem Block Diagram

1.7.1 Audio Subsystem Software

Audio software and drivers are available from Intel’s World Wide Web site.

1.7.2 Audio Connectors and Headers

back panel microphone connectors. The back panel audio connectors are configurable through the audio device drivers. The available configurable audio ports are shown in Figure 8. Figure 8. Front/Back Panel Audio Connector Options

1.8 LAN Subsystem

  • Intel 82562G Platform LAN Connect (PLC) device for 10/100 Mbits/sec Ethernet LAN connectivity
  • Intel 82801GB ICH7
  • RJ-45 LAN connector with integrated status LEDs Additional features of the LAN subsystem include:
  • CSMA/CD protocol engine
  • LAN connect interface between ICH7 and PLC device
  • PCI Conventional bus power management ⎯ Supports ACPI technology ⎯ Supports LAN wake capabilities

1.8.1 Intel® 82562G PLC Device

  • Basic 10/100 Ethernet LAN connectivity
  • Full device driver compatibility
  • Programmable transit threshold
  • Configuration EEPROM that contains the MAC address

1.8.2 LAN Subsystem Software

LAN software and drivers are available from Intel’s World Wide Web site.

1.8.3 RJ-45 LAN Connector with Integrated LEDs

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 9 below). Figure 9. LAN Connector LED Locations

Table 5. LAN Connector LED States Off LAN link is not established. Blinking LAN activity is occurring. Off 10 Mbits/sec data rate is selected. On 100 Mbits/sec data rate is selected.

1.9 Hardware Management Subsystem

  • Fan monitoring and control
  • Thermal and voltage monitoring
  • Chassis intrusion detection

1.9.1 Hardware Monitoring and Fan Control

  • Power supply monitoring of four voltages (+5 V, +12 V, +3.3 VSB, and +VCCP) to detect levels above or below acceptable values
  • Thermally monitored closed-loop fan control, for all three fans, that can adjust the fan speed or switch the fans on or off as needed

1.9.2 Fan Monitoring

1.9.3 Chassis Intrusion and Detection

switch is in the closed position.

1.9.4 Thermal Monitoring

Figure 10 shows the locations of the thermal sensors and fan headers. Figure 10. Thermal Sensors and Fan Headers

1.10 Power Management

  • Software support through Advanced Configuration and Power Interface (ACPI)
  • Hardware support: ⎯ Power connector ⎯ Fan headers ⎯ LAN wake capabilities ⎯ Instantly Available PC technology ⎯ Resume on Ring ⎯ Wake from USB ⎯ Wake from PS/2 devices ⎯ Power Management Event signal (PME#) wake-up support

1.10.1 ACPI

  • Plug and Play (including bus and device enumeration)
  • Power management control of individual devices, add-in boards (some add-in boards may require an ACPI-aware driver), video displays, and hard disk drives
  • Methods for achieving less than 15-watt system operation in the power-on/standby sleeping state
  • A Soft-off feature that enables the operating system to power-off the computer
  • Support for multiple wake-up events (see Table 8 on page 33)
  • Support for a front panel power and sleep mode switch

depending on how ACPI is configured with an ACPI-aware operating system. Table 6. Effects of Pressing the Power Switch

1.10.1.1 System States and Power States

on user preferences and knowledge of how devices are being used by applications. various system and power states. Table 7. Power States and Targeted System Power

  1. Total system power is dependent on the system co nfiguration, including add-in boards and peripherals

powered by the system chassis’ power supply.

  1. Dependent on the standby power consumptio n of wake-up devices used in the system.

1.10.1.2 Two-Watt Standby

to the S5 state when the computer is turned off, but still connected to AC power. also be needed to achieve this goal.

1.10.1.3 Wake-up Devices and Events

Table 8. Wake-up Devices and Events Power On will enable a wake-up event from LAN in the S5 state. fully support ACPI wake events.

1.10.2 Hardware Support

on the wake devices supported and manufacturing options.

  • Power connector
  • Fan headers
  • LAN wake capabilities
  • Instantly Available PC technology
  • Resume on Ring
  • Wake from USB
  • Wake from PS/2 keyboard
  • PME# signal wake-up support
  • WAKE# signal wake-up support LAN wake capabilities and Instantly Available PC technology require power from the +5 V standby line.

Intel Desktop Board D946GZTS Technical Product Specification Resume on Ring enables telephony devices to access the computer when it is in a power-managed state. The method used depends on the type of telephony device (external or internal). NOTE The use of Resume on Ring and Wake from USB technologies from an ACPI state requires an operating system that provides full ACPI support.

1.10.2.1 Power Connector

ATX12V-compliant power supplies can turn off the system power through system control. When an ACPI-enabled system receives the correct command, the power supply removes all non-standby voltages. When resuming from an AC power failure, the computer returns to the power state it was in before power was interrupted (on or off). The computer’s response can be set using the Last Power State feature in the BIOS Setup program’s Boot menu. For information about Refer to The location of the main power connector Figure 14, page 46 The signal names of the main power connector Table 23, page 50

1.10.2.2 Fan Headers

The function/operation of the fan headers is as follows:

  • The fans are on when the board is in the S0 or S1 state.
  • The fans are off when the board is off or in the S3, S4, or S5 state.
  • Each fan header is wired to a fan tachometer input of the hardware monitoring and fan control device.
  • All fan headers support closed-loop fan control that can adjust the fan speed or switch the fan on or off as needed.
  • All fan headers have a +12 V DC connection. For information about Refer to The locations of the fan headers and thermal sensors Figure 10, page 30 The signal names of the processor fan header Table 18, page 48 The signal names of the chassis fan headers Table 17, page 48

1.10.2.3 LAN Wake Capabilities

For LAN wake capabilities, the +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to provide adequate standby current when implementing LAN wake capabilities can damage the power supply. LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem PCI bus network adapter monitors network traffic at the Media Independent Interface. Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer. Depending on the LAN implementation, the board supports LAN wake capabilities with ACPI in the following ways:

  • The PCI Express WAKE# signal
  • The PCI bus PME# signal for PCI 2.3 compliant LAN designs
  • The onboard LAN subsystem

1.10.2.4 Instantly Available PC Technology

For Instantly Available PC technology, the +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to provide adequate standby current when implementing Instantly Available PC technology can damage the power supply. Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to- RAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the power supply is off, and the front panel LED is amber if dual colored, or off if single colored.) When signaled by a wake-up device or event, the system quickly returns to its last known wake state. Table 8 on page 33 lists the devices and events that can wake the computer from the S3 state. The board supports the PCI Bus Power Management Interface Specification. Add-in boards that also support this specification can participate in power management and can be used to wake the computer. The use of Instantly Available PC technology requires operating system support and PCI 2.3 compliant add-in cards and drivers.

1.10.2.5 Resume on Ring

The operation of Resume on Ring can be summarized as follows:

  • Resumes operation from ACPI S1 or S3 states
  • Detects incoming call similarly for external and internal modems
  • Requires modem interrupt be unmasked for correct operation

1.10.2.6 Wake from USB

USB bus activity wakes the computer from ACPI S1 or S3 states. Wake from USB requires the use of a USB peripheral that supports Wake from USB.

1.10.2.7 Wake from PS/2 Devices

PS/2 device activity wakes the computer from an ACPI S1 or S3 state.

1.10.2.8 PME# Signal Wake-up Support

S1, S3, S4, or S5 state (with Wake on PME enabled in BIOS).

1.10.2.9 WAKE# Signal Wake-up Support

an ACPI S1, S3, S4, or S5 state. board. Failure to do so could damage the board and any attached devices. Figure 11. Location of the Standby Power Indicator LED

2 Technical Reference

What This Chapter Contains

2.1 Memory Map

2.1.1 Addressable Memory

The board utilizes 4 GB of addressable system memory. Typically the address space that is allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash), and chipset overhead resides above the top of DRAM (total system memory). On a system that has 4 GB of system memory installed, it is not possible to use all of the installed memory due to system address space being allocated for other system critical functions. These functions include the following:

  • BIOS/ SPI Flash (4 Mbits)
  • Local APIC (19 MB)
  • Digital Media Interface (40 MB)
  • Front side bus interrupts (17 MB)
  • PCI Express configuration space (256 MB)
  • MCH base address registers, internal graphics ranges, PCI Express ports (up to

512 MB)

  • Memory-mapped I/O that is dynamically allocated for PCI Conventional and PCI Express add-in cards
  • Base graphics memory support (1 MB or 8 MB)

system memory can be used when there is no overlap of system addresses.

16 KB x 4)

16 KB x 8)

Figure 12. Detailed System Memory Address Map

Table 9 lists the system memory map. Table 9. System Memory Map

1024 K - 4194304 K 100000 - FFFFFFFF 4095 MB Extended memory

960 K - 1024 K F0000 - FFFFF 64 KB Runtime BIOS

896 K - 960 K E0000 - EFFFF 64 KB Reserved

800 K - 896 K C8000 - DFFFF 96 KB Potential available high DOS

memory (open to the PCI bus). Dependent on video adapter used.

640 K - 800 K A0000 - C7FFF 160 KB Video memory and BIOS

639 K - 640 K 9FC00 - 9FFFF 1 KB Extended BIOS data (movable by

memory manager software)

512 K - 639 K 80000 - 9FBFF 127 KB Extended conventional memory

0 K - 512 K 00000 - 7FFFF 512 KB Conventional memory

2.2 DMA Channels

Table 10. DMA Channels

2.3 Fixed I/O Map

Table 11. I/O Map data sheet for dynamic addressing information.

  1. Default, but can be changed to another address range

ICH7 data sheet provides more information on address aliasing.

2.4 PCI Configuration Space Map

Table 12. PCI Configuration Space Map 00 00 00 Memory controller of Intel 82946GZ component 00 01 00 PCI Express x16 graphics port (Note 1) 00 02 00 Integrated graphics controller 00 1B 00 Intel High Definition Audio Controller 00 1C 00 PCI Express port 1 00 1C 01 PCI Express port 2 00 1C 02 PCI Express port 3 00 1C 03 PCI Express port 4 00 1C 04 PCI Express port 5 00 1D 00 USB UHCI controller 1 00 1D 01 USB UHCI controller 2 00 1D 02 USB UHCI controller 3 00 1D 03 USB UHCI controller 4 00 1D 07 EHCI controller #1 00 1E 00 PCI bridge 00 1F 00 PCI controller 00 1F 01 Parallel ATA IDE controller 00 1F 02 Serial ATA controller #1 00 1F 03 SMBus controller (Note 2) 08 00 LAN controller (Note 2) 00 00 PCI Conventional bus connector 1 (Note 2) 01 00 PCI Conventional bus connector 2 01 00 00 PCI Express Video Controller (Note 1) Notes: 1. Present only when a PCI Express x16 graphics card is installed. 2. Bus number is dynamic and can change based on add-in cards used.

2.5 Interrupts

supports a total of 24 interrupts. Table 13. Interrupts

0 Reserved, interval timer

1 Reserved, keyboard buffer full

2 Reserved, cascade interrupt from slave PIC

3 COM2 (Note 1)

4 COM1 (Note 1)

5 LPT2 (Plug and Play option)/User available

6 Diskette drive

7 LPT1 (Note 1)

8 Real-time clock

9 Reserved for ICH7 system management bus

10 User available

11 User available

12 Onboard mouse port (if pres ent, else user available)

13 Reserved, math coprocessor

14 Primary IDE/Serial ATA (if present, else user available)

15 Secondary IDE/Serial ATA (if present, else user available)

  1. Default, but can be changed to another IRQ.
  2. Available in APIC mode only.

2.6 PCI Interrupt Routing Map

  • INTA: By default, all add-in cards that require only one interrupt are in this category. For almost all cards that require more than one interrupt, the first interrupt on the card is also classified as INTA.
  • INTB: Generally, the second interrupt on add-in cards that require two or more interrupts is classified as INTB. (This is not an absolute requirement.)
  • INTC and INTD: Generally, a third interrupt on add-in cards is classified as INTC and a fourth interrupt is classified as INTD. The ICH7 has eight Programmable Interrupt Request (PIRQ) input signals. All PCI interrupt sources either onboard or from a PCI add-in card connect to one of these PIRQ signals. Some PCI interrupt sources are electrically tied together on the board and therefore share the same interrupt. Table 14 shows an example of how the PIRQ signals are routed.

Table 14. PCI Interrupt Routing Map PCI interrupt assignments to USB ports and Serial ATA ports are dynamic.

Intel Desktop Board D946GZTS Technical Product Specification

2.7 Connectors and Headers

Only the following connectors have overcurrent protection: Back panel and front panel USB, PS/2, and VGA. The other internal connectors/headers are not overcurrent protected and should connect only to devices inside the computer’s chassis, such as fans and internal peripherals. Do not use these connectors/headers to power devices external to the computer’s chassis. A fault in the load presented by the external devices could cause damage to the computer, the power cable, and the external devices themselves. This section describes the board’s connectors and headers. The connectors and headers can be divided into these groups:

  • Back panel I/O connectors (see page 45)
  • Component-side connectors and headers (see page 46)

2.7.1 Back Panel Connectors

Figure 13 shows the location of the back panel connectors. Figure 13. Back Panel Connectors

2.7.2 Component-side Connectors and Headers

Figure 14 shows the locations of the component-side connectors and headers. Figure 14. Component-side Connectors and Headers

Table 15 lists the component-side connectors and headers identified in Figure 14. Table 15. Component-side Connectors and Headers Shown in Figure 14 A Front panel audio header B High Definition Audio Link header C Serial ATA connectors [4] D Chassis intrusion header E Front panel USB headers [2] F Main power connector G PCI Express x16 add-in card connector H PCI Express x1 add-in card connector I PCI Conventional bus add-in card connector 1 J PCI Conventional bus add-in card connector 2 K Diskette drive connector L Front panel header M Front chassis fan header N Auxiliary front panel power LED header O Processor core power connector P Processor fan header Q Rear chassis fan header R Parallel ATA IDE connector Table 16. Front Panel Audio Header

7 SENSE_SEND (Jack detection) 8 Key (no pin)

Table 17. Front and Rear Chassis Fan Headers

1 Control

3 Tach

Table 18. Processor Fan Header

1 Ground

3 FAN_TACH

4 FAN_CONTROL

Table 19. Chassis Intrusion Header

1 Intruder

2 Ground

Table 20. Serial ATA Connectors

2 TXP

3 TXN

4 Ground

5 RXN

6 RXP

7 Ground

Table 21. High Definition Audio Link Header

1 BCLK 2 Ground

5 SYNC 6 Ground

9 SDI 10 +12 V

11 No connect 12 Key (no pin)

15 No connect 16 Ground

2.7.2.1 Add-in Card Connectors

The board has the following add-in card connectors:

  • PCI Express x16: one connector supporting simultaneous transfer speeds up to

4 GBytes/sec of peak bandwidth per direction and up to 8 GBytes/sec concurrent

  • PCI Express x1: one PCI Express x1 connector. The x1 interface supports simultaneous transfer speeds up to 250 Mbytes/sec of peak bandwidth per direction and up to 500 MBytes/sec concurrent bandwidth
  • PCI Conventional (rev 2.3 compliant) bus: two PCI Conventional bus add-in card connectors. The SMBus is routed to PCI Conventional bus connector 2 only. PCI Conventional bus add-in cards with SMBus support can access sensor data and other information residing on the board. Note the following considerations for the PCI Conventional bus connectors:
  • All of the PCI Conventional bus connectors are bus master capable.
  • SMBus signals are routed to PCI Conventional bus connector 2. This enables PCI Conventional bus add-in boards with SMBus support to access sensor data on the board. The specific SMBus signals are as follows: ⎯ The SMBus clock line is connected to pin A40. ⎯ The SMBus data line is connected to pin A41.

2.7.2.2 Power Supply Connectors

  • Main power – a 2 x 12 connector. This connector is compatible with 2 x 10 connectors previously used on Intel Desktop boards. The board supports the use of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When using a power supply with a 2 x 10 main power cable, attach that cable on the rightmost pins of the main power connector, leaving pins 11, 12, 23, and 24 unconnected.
  • Processor core power – a 2 x 2 connector. This connector provides power directly to the processor voltage regulator and must always be used. Failure to do so will prevent the board from booting.

Table 22. Processor Core Power Connector

1 Ground 2 Ground

Table 23. Main Power Connector

3 Ground 15 Ground

5 Ground 17 Ground

7 Ground 19 Ground

8 PWRGD (Power Good) 20 No connect

Note: When using a 2 x 10 power supply cable, this pin will be unconnected.

2.7.2.3 Front Panel Header

This section describes the functions of the front panel header. Table 24 lists the signal names of the front panel header. Figure 15 is a connection diagram for the front panel header. Table 24. Front Panel Header Hard Drive Activity LED Power LED

1 HD_PWR Out Hard disk LED

2 HDR_BLNK_GRN Out Front panel green

3 HDA# Out Hard disk active

4 HDR_BLNK_YEL Out Front panel yellow

Reset Switch On/Off Switch

5 Ground Ground 6 FPBUT_IN In Power switch

7 FP_RESET# In Reset switch 8 Ground Ground

9 +5 V Power 10 N/C Not connected Dual- colored Power LED Single- colored Power LED OM18318 Hard Drive Activity LED Reset Switch +5 V DC N/C Power Switch - + Figure 15. Connection Diagram for Front Panel Header

2.7.2.3.1 Hard Drive Activity LED Header

  • A Serial ATA hard drive connected to an onboard Serial ATA connector
  • A Parallel ATA IDE hard drive connected to an onboard Parallel ATA IDE connector

2.7.2.3.2 Reset Switch Header

2.7.2.3.3 Power/Sleep LED Header

Table 25. States for a One-Color Power LED Table 26. States for a Two-Color Power LED colors are product- or customer-specific.

2.7.2.3.4 Power Switch Header

2.7.2.4 Front Panel USB Headers

Figure 16 is a connection diagram for the front panel USB headers.

  • The +5 V DC power on the USB headers is fused.
  • Use only a front panel USB connector that conforms to the USB 2.0 specification for high-speed USB devices. OM18317 Key (no pin) No connect Power (+5 V DC) Ground Ground Power (+5 V DC) One USB Port One USB Port

Figure 16. Connection Diagram for Front Panel USB Headers

2.8 Jumper Block

version in the BIOS and reports if the two match. Figure 17. Location of the Jumper Block Table 27. BIOS Setup Configuration Jumper Settings maintenance menu is displayed. recovery diskette is required.

2.9 Mechanical Considerations

2.9.1 Form Factor

mechanical form factor for the board. Dimensions are given in inches [millimeters]. Figure 18. Board Dimensions

2.9.2 I/O Shield

The I/O shield drawing is for reference only.

172.93 REF

13.00 TYP

42.84 REF

Figure 19. I/O Shield Dimensions

2.10 Electrical Considerations

2.10.1 DC Loading

on the system’s usage model and not necessarily tied to a particular processor speed. Table 28. DC Loading Characteristics

2.10.2 Fan Header Current Capability

component damage that will halt fan operation. Table 29 lists the current capability of the fan headers. Table 29. Fan Header Current Capability

Intel Desktop Board D946GZTS Technical Product Specification

2.10.3 Add-in Board Considerations

The board is designed to provide 2 A (average) of +5 V current for each add-in board. The total +5 V current draw for add-in boards for a fully loaded board (all three expansion slots and the PCI Express x16 connector filled) must not exceed 8 A.

2.10.4 Power Supply Considerations

The +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to do so can damage the power supply. The total amount of standby current required depends on the wake devices supported and manufacturing options. System integrators should refer to the power usage values listed in Table 28 when selecting a power supply for use with the board. Additional power required will depend on configurations chosen by the integrator. The power supply must comply with the indicated parameters of the ATX form factor specification.

  • The potential relation between 3.3 VDC and +5 VDC power rails
  • The current capability of the +5 VSB line
  • All timing parameters
  • All voltage tolerances

2.11 Thermal Considerations

A chassis with a maximum internal ambient temperature of 38 oC at the processor fan inlet is a requirement. Use a processor heat sink that provides omni-directional airflow to maintain required airflow across the processor voltage regulator area. CAUTION This board requires the use of a BTX Type I or Type II Thermal Module for the processor. Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board. For a list of chassis that have been tested with Intel desktop boards please refer to the following website: http://developer.intel.com/design/motherbd/cooling.htm All responsibility for determining the adequacy of any thermal or system design remains solely with the reader. Intel makes no warranties or representations that merely following the instructions presented in this document will result in a system with adequate thermal performance. CAUTION Ensure that the ambient temperature does not exceed the board’s maximum operating temperature. Failure to do so could cause components to exceed their maximum case temperature and malfunction. For information about the maximum operating temperature, see the environmental specifications in Section 2.13. CAUTION Ensure that proper airflow is maintained in the processor voltage regulator circuit. Failure to do so may result in damage to the voltage regulator circuit. The processor voltage regulator area (shown in Figure 20) can reach a temperature of up to 85 oC in an open chassis.

Table 30. Thermal Considerations for Components

2.12 Reliability

prediction is used to estimate repair rates and spare parts requirements. D946GZTS MTBF is 132,431.56 hours.

2.13 Environmental

Table 31 lists the environmental specifications for the board. Table 31. Desktop Board D946GZTS Environmental Specifications

Intel Desktop Board D946GZTS Technical Product Specification

What This Chapter Contains

3.1 Introduction

The board uses an Intel BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash contains the BIOS Setup program, POST, the PCI auto-configuration utility, and Plug and Play support. The BIOS displays a message during POST identifying the type of BIOS and a revision code. The initial production BIOSs are identified as TS94610J.86A. When the BIOS Setup configuration jumper is set to configure mode and the computer is powered-up, the BIOS compares the CPU version and the microcode version in the BIOS and reports if the two match. The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the <F2> key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. The menu bar is shown below. Maintenance Main Advanced Security Power Boot Exit NOTE The maintenance menu is displayed only when the board is in configure mode. Section 2.8 on page 54 shows how to put the board in configure mode.

Intel Desktop Board D946GZTS Technical Product Specification Table 32 lists the BIOS Setup program menu features. Table 32. BIOS Setup Program Menu Bar

features

Table 33 lists the function keys available for menu screens. Table 33. BIOS Setup Program Function Keys <←> or <→> Selects a different menu screen (Moves the cursor left or right) <↑> or <↓> Selects an item (Moves the cursor up or down) <Tab> Selects a field (Not implemented) <Enter> Executes command or selects the submenu <F9> Load the default configurat ion values for the current menu <F10> Save the current values and exits the BIOS Setup program <Esc> Exits the menu

3.2 BIOS Flash Memory Organization

The Serial Peripheral Interface Flash Memory (SPI Flash) includes a 4 Mbit (512 KB) flash memory device

3.3 Resource Configuration

3.3.1 PCI Autoconfiguration

The BIOS can automatically configure PCI devices. PCI devices may be onboard or add-in cards. Autoconfiguration lets a user insert or remove PCI cards without having to configure the system. When a user turns on the system after adding a PCI card, the BIOS automatically configures interrupts, the I/O space, and other system resources. Any interrupts set to Available in Setup are considered to be available for use by the add-in card.

3.3.2 PCI IDE Support

If you select Auto in the BIOS Setup program, the BIOS automatically sets up the PCI IDE connector with independent I/O channel support. The IDE interface supports hard drives up to ATA-66/100 and recognizes any ATAPI compliant devices, including CD-ROM drives, tape drives, and Ultra DMA drives. The BIOS determines the capabilities of each drive and configures them to optimize capacity and performance. To take advantage of the high capacities typically available today, hard drives are automatically configured for Logical Block Addressing (LBA) and to PIO Mode 3 or 4, depending on the capability of the drive. You can override the auto-configuration options by specifying manual configuration in the BIOS Setup program. To use ATA-66/100 features the following items are required:

  • An ATA-66/100 peripheral device
  • An ATA-66/100 compatible cable
  • ATA-66/100 operating system device drivers NOTE Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device. For example, do not connect an ATA hard drive as a slave to an ATAPI CD-ROM drive.

3.4 System Management BIOS (SMBIOS)

SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network. The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components. Using SMBIOS, a system administrator can obtain the system types, capabilities, operational status, and installation dates for system components. The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as third-party management software to use SMBIOS. The BIOS stores and reports the following SMBIOS information:

  • BIOS data, such as the BIOS revision level
  • Fixed-system data, such as peripherals, serial numbers, and asset tags
  • Resource data, such as memory size, cache size, and processor speed
  • Dynamic data, such as event detection and error logging Non-Plug and Play operating systems, such as Windows NT*, require an additional interface for obtaining the SMBIOS information. The BIOS supports an SMBIOS table interface for such operating systems. Using this support, an SMBIOS service-level application running on a non-Plug and Play operating system can obtain the SMBIOS information.

Intel Desktop Board D946GZTS Technical Product Specification

3.5 Legacy USB Support

Legacy USB support enables USB devices to be used even when the operating system’s USB drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB support is set to Enabled. Legacy USB support operates as follows: 1. When you apply power to the computer, legacy support is disabled. 2. POST begins. 3. Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to enter and configure the BIOS Setup program and the maintenance menu. 4. POST completes. 5. The operating system loads. While the operating system is loading, USB keyboards and mice are recognized and may be used to configure the operating system. (Keyboards and mice are not recognized during this period if Legacy USB support was set to Disabled in the BIOS Setup program.) 6. After the operating system loads the USB drivers, all legacy and non-legacy USB devices are recognized by the operating system, and Legacy USB support from the BIOS is no longer used. To install an operating system that supports USB, verify that Legacy USB support in the BIOS Setup program is set to Enabled and follow the operating system’s installation instructions.

3.6 BIOS Updates

The BIOS can be updated using either of the following utilities, which are available on the Intel World Wide Web site:

  • Intel® Express BIOS Update utility, which enables automated updating while in the Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a 1.44 MB diskette, or a CD-ROM, or from the file location on the Web.
  • Intel® Flash Memory Update Utility, which requires creation of a boot diskette and manual rebooting of the system. Using this utility, the BIOS can be updated from a file on a 1.44 MB diskette (from a legacy diskette drive or an LS-120 diskette drive) or a CD-ROM. Both utilities verify that the updated BIOS matches the target system to prevent accidentally installing an incompatible BIOS. NOTE Review the instructions distributed with the upgrade utility before attempting a BIOS update. For information about Refer to The Intel World Wide Web site Section 1.2, page 15

3.6.1 Language Support

The BIOS Setup program and help messages are supported in US English. Additional languages are available in the Integrator’s Toolkit utility. Check the Intel website for details.

3.6.2 Custom Splash Screen

During POST, an Intel® splash screen is displayed by default. This splash screen can be augmented with a custom splash screen. The Integrator’s Toolkit that is available from Intel can be used to create a custom splash screen. NOTE If you add a custom splash screen, it will share space with the Intel branded logo. For information about Refer to The Intel World Wide Web site Section 1.2, page 15

3.7 Boot Options

In the BIOS Setup program, the user can choose to boot from a diskette drive, hard drives, CD-ROM, or the network. The default setting is for the diskette drive to be the first boot device, the hard drive second, and the ATAPI CD-ROM third. The fourth device is disabled.

3.7.1 CD-ROM Boot

Booting from CD-ROM is supported in compliance to the El Torito bootable CD-ROM format specification. Under the Boot menu in the BIOS Setup program, ATAPI CD- ROM is listed as a boot device. Boot devices are defined in priority order. Accordingly, if there is not a bootable CD in the CD-ROM drive, the system will attempt to boot from the next defined drive.

3.7.2 Network Boot

The network can be selected as a boot device. This selection allows booting from the onboard LAN or a network add-in card with a remote boot ROM installed. Pressing the <F12> key during POST automatically forces booting from the LAN. To use this key during POST, the User Access Level in the BIOS Setup program's Security menu must be set to Full.

3.7.3 Booting Without Attached Devices

  • Video adapter
  • Keyboard
  • Mouse

3.7.4 Changing the Default Boot Device During POST

Boot Device Priority Submenu). Table 34 lists the boot device menu options. Table 34. Boot Device Menu Options

3.8 Adjusting Boot Speed

  • Selecting and configuring peripherals properly
  • Optimized BIOS boot parameters

3.8.1 Peripheral Selection and Configuration

  • Choose a hard drive with parameters such as “power-up to data ready” less than eight seconds, that minimize hard drive startup delays.
  • Select a CD-ROM drive with a fast initialization rate. This rate can influence POST execution time.
  • Eliminate unnecessary add-in adapter features, such as logo displays, screen repaints, or mode changes in POST. These features may add time to the boot process.
  • Try different monitors. Some monitors initialize and communicate with the BIOS more quickly, which enables the system to boot more quickly.

3.8.2 BIOS Boot Optimizations

Use of the following BIOS Setup program settings reduces the POST execution time.

  • In the Boot Menu, set the hard disk drive as the first boot device. As a result, the POST does not first seek a diskette drive, which saves about one second from the POST execution time.
  • In the Peripheral Configuration submenu, disable the LAN device if it will not be used. This can reduce up to four seconds of option ROM boot time. NOTE It is possible to optimize the boot process to the point where the system boots so quickly that the Intel logo screen (or a custom logo splash screen) will not be seen. Monitors and hard disk drives with minimum initialization times can also contribute to a boot time that might be so fast that necessary logo screens and POST messages cannot be seen. This boot time may be so fast that some drives might be not be initialized at all. If this condition should occur, it is possible to introduce a programmable delay ranging from three to 30 seconds (using the Hard Disk Pre-Delay feature of the Advanced Menu in the Drive Configuration Submenu of the BIOS Setup program).

3.9 BIOS Security Features

  • The supervisor password gives unrestricted access to view and change all the Setup options in the BIOS Setup program. This is the supervisor mode.
  • The user password gives restricted access to view and change Setup options in the BIOS Setup program. This is the user mode.
  • If only the supervisor password is set, pressing the <Enter> key at the password prompt of the BIOS Setup program allows the user restricted access to Setup.
  • If both the supervisor and user passwords are set, users can enter either the supervisor password or the user password to access Setup. Users have access to Setup respective to which password is entered.
  • Setting the user password restricts who can boot the computer. The password prompt will be displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, the user can enter either password to boot the computer.
  • For enhanced security, use different passwords for the supervisor and user passwords.
  • Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 16 characters in length. Table 35 shows the effects of setting the supervisor password and user password. This table is for reference only and is not displayed on the screen.

Table 35. Supervisor and User Password Functions Note: If no password is set, any us er can change all Setup options.

4.1 Speaker

4.2 BIOS Beep Codes

message describing the problem (see Table 36). Table 36. Beep Codes

4.3 BIOS Error Messages

Table 37 lists the error messages and provides a brief description of each. Table 37. BIOS Error Messages CMOS Battery Low The battery may be losing power. Replace the battery soon. corrupted. Run Setup to reset values. was removed then memory may be bad. No Boot Device Available System did not find a device to boot.

4.4 Port 80h POST Codes

at port 80h. This code is useful for determining the point where an error occurred. Displaying the POST-codes requires a PCI bus add-in card, often called a POST card. The POST card must be installed in PCI bus connector 1.

  • Table 38 lists the Port 80h POST code ranges
  • Table 39 lists the Port 80h POST codes themselves
  • Table 40 lists the Port 80h POST sequence NOTE In the tables listed above, all POST codes and range values are listed in hexadecimal.

Table 38. Port 80h POST Code Ranges 00 – 0F Debug codes: Can be used by any PEIM/driver for debug. 10 – 1F Host Processors: 1F is an unrecoverable CPU error. 20 – 2F Memory/Chipset: 2F is no memory detected or no useful memory detected. 30 – 3F Recovery: 3F indicated recovery failure. 40 – 4F Reserved for future use. 50 – 5F I/O Busses: PCI, USB, I SA, ATA, etc. 5F is an unrecoverable error. Start with PCI. 60 – 6F Reserved for future use (for new busses). 70 – 7F Output Devices: All output co nsoles. 7F is an unrecoverable error. 80 – 8F Reserved for future us e (new output console codes). 90 – 9F Input devices: Keyboard/Mouse . 9F is an unrecoverable error. A0 – AF Reserved for future use (new input console codes). B0 – BF Boot Devices: Includes fixed media and removable media. BF is an unrecoverable error. C0 – CF Reserved for future use. D0 – DF Boot device selection. E0 – FF F0 – FF: FF processor exception. E0 – EE: Miscellaneous codes. See Table 39.

Table 39. Port 80h POST Codes

10 Power-on initialization of the host processor (Boot Strap Processor)

11 Host processor Cache initialization (including APs)

12 Starting Application processor initialization

13 SMM initialization

21 Initializing a chipset component

22 Reading SPD from memory DIMMs

23 Detecting presence of memory DIMMs

24 Programming timing parameters in the memory controller and the DIMMs

25 Configuring memory

26 Optimizing memory settings

27 Initializing memory, such as ECC init

28 Testing memory

50 Enumerating PCI busses

51 Allocating resources to PCI bus

52 Hot Plug PCI controller initialization

58 Resetting USB bus

59 Reserved for USB

70 Resetting the VGA controller

71 Disabling the VGA controller

72 Enabling the VGA controller

78 Resetting the console controller

79 Disabling the console controller

Table 39. Port 80h POST Codes (continued)

90 Resetting keyboard

91 Disabling keyboard

92 Detecting presence of keyboard

93 Enabling the keyboard

94 Clearing keyboard input buffer

95 Instructing keyboard controller to run Self Test (PS2 only)

98 Resetting mouse

99 Disabling mouse

30 Crisis Recovery has initiated per User request

31 Crisis Recovery has initiated by software (corrupt flash)

34 Loading recovery capsule

35 Handing off control to the recovery capsule

Table 40. Typical Port 80h POST Sequence

51 Allocating resourced to PCI bus

92 Detecting the presence of the keyboard

95 Keyboard Self Test

01 INT 19

00 Ready to boot

5 Regulatory Compliance and Battery

5.1 Regulatory Compliance

  • Safety regulations
  • European Union Declaration of Conformity statement
  • Product Ecology statements
  • Electromagnetic Compatibility (EMC) regulations
  • Product certification markings

5.1.1 Safety Regulations

when correctly installed in a compatible host system. Table 41. Safety Regulations

Intel Desktop Board D946GZTS Technical Product Specification

5.1.2 European Union Declaration of Conformity

We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board D946GZTS is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 89/336/EEC (EMC Directive) and Council Directive 73/23/EEC (Safety/Low Voltage Directive). The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 89/336/EEC and 73/23/EEC. Čeština Tento výrobek odpovídá požadavkům evropských směrnic 89/336/EEC a 73/23/EEC. Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 89/336/EEC & 73/23/EEC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 89/336/EEC & 73/23/EEC. Eesti Antud toode vastab Euroopa direktiivides 89/336/EEC ja 73/23/EEC kehtestatud nõuetele. Suomi Tämä tuote noudattaa EU-direktiivin 89/336/EEC & 73/23/EEC määräyksiä. Français Ce produit est conforme aux exigences de la Directive Européenne 89/336/EEC & 73/23/EEC. Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 89/336/EEC & 73/23/EEC. Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών 89/336/ΕΟΚ και 73/23/ΕΟΚ. Magyar E termék megfelel a 89/336/EEC és 73/23/EEC Európai Irányelv előírásainak. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 89/336/ EEC & 73/23/EEC. Italiano Questo prodotto è conforme alla Direttiva Europea 89/336/EEC & 73/23/EEC. Latviešu Šis produkts atbilst Eiropas Direktīvu 89/336/EEC un 73/23/EEC noteikumiem. Lietuvių Šis produktas atitinka Europos direktyvų 89/336/EEC ir 73/23/EEC nuostatas.

Regulatory Compliance and Battery Disposal Information Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 89/336/EEC u 73/23/EEC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 89/336/ EEC & 73/23/EEC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 89/336/EWG i 73/23/EWG. Portuguese Este produto cumpre com as normas da Diretiva Européia 89/336/EEC & 73/23/EEC. Español Este producto cumple con las normas del Directivo Europeo 89/336/EEC & 73/23/EEC. Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív 89/336/EEC a 73/23/EEC. Slovenščina Izdelek je skladen z določbami evropskih direktiv 89/336/EGS in 73/23/EGS. Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 89/336/EEC & 73/23/EEC. Türkçe Bu ürün, Avrupa Birliği’nin 89/336/EEC ve 73/23/EEC yönergelerine uyar.

Intel Desktop Board D946GZTS Technical Product Specification

5.1.3 Product Ecology Statements

The following information is provided to address worldwide product ecology concerns and regulations.

5.1.3.1 Disposal Considerations

This product contains the following materials that may be regulated upon disposal: lead solder on the printed wiring board assembly.

5.1.3.2 Recycling Considerations

As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to select locations for proper recycling. Please consult the http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc. 中文 作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program （英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作 恰当的重复使用处理。 请参考http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm 了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。 Deutsch Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben. Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm Español Como parte de su compromiso de responsabilidad medioambiental, Intel ha implantado el programa de reciclaje de productos Intel, que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado. Consulte la http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm para ver los detalles del programa, que incluye los productos que abarca, los lugares disponibles, instrucciones de envío, términos y condiciones, etc.

Regulatory Compliance and Battery Disposal Information Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à des adresses spécifiées. Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm pour en savoir plus sur ce programme, à savoir les produits concernés, les adresses disponibles, les instructions d'expédition, les conditions générales, etc. 日本語 インテルでは、環境保護活動の一環として、使い終えたインテル ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル プログラムを発足させました。 対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、 http://www.intel.com/in tel/other/ehs/product_ecology/Recycling_Program.htm （英語）をご覧ください。 Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran, Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi-lokasi terpilih untuk dikitarkan semula dengan betul. Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm untuk mendapatkan butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia, arahan penghantaran, terma & syarat, dsb. Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada. Consulte o site http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm (em Inglês) para obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os locais disponíveis, as instruções de envio, os termos e condições, etc. Russian В качестве части своих обязательств к окружающей среде, в Intel создана программа утилизации продукции Intel (Product Recycling Program) для предоставления конечным пользователям марок продукции Intel возможности возврата используемой продукции в специализированные пункты для должной утилизации. Пожалуйста, обратитесь на веб-сайт http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.htm за информацией об этой программе, принимаемых продуктах, местах приема, инструкциях об отправке, положениях и условиях и т.д.

5.1.3.3 Lead Free Desktop Board

Table 42. Lead-Free Board Markings

5.1.4 EMC Regulations

correctly installed in a compatible host system. Table 43. EMC Regulations VCCI (Class B) Voluntary Control for Interfere nce by Information Technology Equipment. according to the instruction manual.

environments and other non-residential environments.

5.1.5 Product Certification Markings (Board Level)

Table 44. Product Certification Markings UL file number for Intel desktop boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and D946GZTS model designation. directive (89/336/EEC) and Low Voltage directive (73/23/EEC). adjacent Intel supplier code number, N-232. Japan VCCI (Voluntary Control Council for Interference) mark. S. Korea MIC (Ministry of Information and Communication) mark. mark. Includes adjacent Intel company number, D33025.

Regulatory Compliance and Battery Disposal Information

5.2 Battery Disposal Information

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. PRECAUTION Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement. FORHOLDSREGEL Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning. OBS! Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til gjeldende miljølovgivning. VIKTIGT! Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljövårdsbestämmelserna. VARO Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti. VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend. AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.

Intel Desktop Board D946GZTS Technical Product Specification PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante. WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving. ATENÇÃO Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região. AŚCIAROŽZNAŚĆ Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі. UPOZORNÌNÍ V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí. Προσοχή Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς. VIGYAZAT Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.

Regulatory Compliance and Battery Disposal Information AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska. PRECAUŢIE Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului. ВНИМАНИЕ При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи должны быть утилизированы по возможности. Утилизация батарей должна проводится по правилам, соответствующим местным требованиям. UPOZORNENIE Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia. POZOR Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo. Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi. UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır. OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

Intel Desktop Board D946GZTS Technical Product Specification