T2800D KERSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

/C0084/C0050/C0056/C0048/C0048/C0068 /C0084/C0114/C0105/C0097/C0099/C0115 Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies. Blocking V oltage to 400 V olts All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability Small, Rugged, Thermowatt Construction for Low Thermal Resistance, High Heat Dissipation and Durability Four Quadrant Gating Device Marking: Logo, Device Type, e.g., T2800D, Date Code MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off–State Voltage(1) (TJ = –40 to +125°C, Gate Open) VDRM, VRRM 400 Volts On–State RMS Current (All Conduction Angles, TC = +80°C) IT(RMS) 8.0 Amps Peak Non–Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TJ = +80°C) ITSM 100 Amps Circuit Fusing Consideration (t = 8.3 ms) I2t A2s Peak Gate Power (Pulse Width = 10 µs, TC = +80°C) PGM Watts Average Gate Power (t = 8.3 ms, TC = +80°C) PG(AV) 0.35 Watt Peak Gate Current (Pulse Width = 10 µs, TC = +80°C) IGM 4.0 Amps Operating Junction Temperature Range TJ –40 to +125 Storage Temperature Range Tstg –40 to +150 TRIACS

8 AMPERES RMS

400 VOLTS

ORDERING INFORMATION

TO–220AB CASE 221A STYLE 4 2 3 PIN ASSIGNMENT

3 Gate

4 Main Terminal 2

www.kersemi.com MT1 G MT2

Thermal Resistance, Junction to Case R θJC 2.2 °C/W Maximum Lead Temperature for Soldering Purposes 1/8″ from Case for 10 Seconds TL 260

ELECTRICAL CHARACTERISTICS

(TC = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Peak Repetitive Blocking Current (VD = Rated VDRM , VRRM ; Gate Open) T C = 25°C TC = 100°C IDRM , IRRM 2.0 µA mA ON CHARACTERISTICS Peak On-State Voltage(1) (IT = /C003430 A Peak) VTM 1.7 2.0 Volts Gate Trigger Current (Continuous dc) (VD = 12 Vdc, RL = 100 Ohms) MT2(+), G(+) MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) IGT mA Gate Trigger Voltage (Continuous dc) (All Quadrants) (VD = 12 Vdc, RL = 100 Ohms) VGT 1.25 2.5 Volts Gate Non–Trigger Voltage (Continuous dc) (VD = 12 V, RL = 100 Ohms, TC = 100°C) VGD 0.2 Volts Holding Current (VD = 12 Vdc, Initiating Current = /C0034200 mA, Gate Open) IH mA Gate Controlled Turn-On Time (VD = Rated VDRM , IT = 10 A, IGT = 80 mA, Rise Time = 0.1 µs) tgt 1.6 µs DYNAMIC CHARACTERISTICS Critical Rate-of-Rise of Commutation Voltage (VD = Rated VDRM , IT(RMS) = 8 A, Commutating di/dt = 4.1 A/ms, Gate Unenergized, TC = 80°C) dv/dt(c) V/µs Critical Rate-of-Rise of Off-State Voltage (VD = Rated VDRM , Exponential Voltage Rise, Gate Open, TC = 100°C) dv/dt V/µs (1) Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%. www.kersemi.com

+ Current + Voltage VTM IH Symbol Parameter VDRM Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current Voltage Current Characteristic of Triacs (Bidirectional Device) IDRM at VDRM on state off state IRRM at VRRM Quadrant 1 MainTerminal 2 + Quadrant 3 MainTerminal 2 –VTM IH VTM Maximum On State Voltage IH Holding Current MT1 (+) IGT GATE (+) MT2 REF MT1 (–) IGT GATE (+) MT2 REF MT1 (+) IGT GATE (–) MT2 REF MT1 (–) IGT GATE (–) MT2 REF MT2 NEGATIVE (Negative Half Cycle) MT2 POSITIVE (Positive Half Cycle) Quadrant III Quadrant IV Quadrant II Quadrant I Quadrant Definitions for a Triac IGT – + IGT All polarities are referenced to MT1. With in–phase signals (using standard AC lines) quadrants I and III are used. www.kersemi.com

Figure 1. Current Derating Figure 2. Power Dissipation

STYLE 4: PIN 1. MAIN TERMINAL 1 2. MAIN TERMINAL 2 3. GATE 4. MAIN TERMINAL 2 TO–220AB CASE 221A–07 ISSUE Z NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.570 0.620 14.48 15.75 B 0.380 0.405 9.66 10.28 C 0.160 0.190 4.07 4.82 D 0.025 0.035 0.64 0.88 F 0.142 0.147 3.61 3.73 G 0.095 0.105 2.42 2.66 H 0.110 0.155 2.80 3.93 J 0.014 0.022 0.36 0.55 K 0.500 0.562 12.70 14.27 L 0.045 0.060 1.15 1.52 N 0.190 0.210 4.83 5.33 Q 0.100 0.120 2.54 3.04 R 0.080 0.110 2.04 2.79 S 0.045 0.055 1.15 1.39 T 0.235 0.255 5.97 6.47 U 0.000 0.050 0.00 1.27 A K L V G D N Z H Q FB 123 –T– SEATING PLANE S R J U T C www.kersemi.com