RFSW6024 PCK-410

RFSW6024 QORVO | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 13

Technical content

5MHz to 6GHz Absorptive High Isolation SPDT Switch Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 1 of 13 www.qorvo.com

16 Pad 4 x 4 mm QFN Package

• 5 – 6000 MHz Operation
• Symmetric SPDT
• Non-Reflective RF1 & RF2 Ports
• No Blocking Capacitors Necessary Unless DC Voltage on RF line
• High Isolation: 60 dB at 2 GHz
• High Input IP3: +66 dBm
• +1.8 V Logic Compatible Product Overview The RFSW6024 is a Silicon on Insulator (SOI) Single-Pole Double Throw (SPDT) switch designed for uses in cellular, 3G, LTE and other high -performance communication systems. It offers a high isolation , symmetric throw ports with excellent linearity and power handling capability. No DC blocking capacitors are necessary on the RF ports. The design is non-reflective as such the RF port 1 or RF port 2 is terminated in the non-throw state. The VEN enable pin allows the switch entering the “All OFF State”. The RFSW6024 is 1.8V positive logic compatible.

Ordering Information

Part No. Description RFSW6024TR13 2,500 pieces on a 13” reel (standard) RFSW6024 PCK-410 5 MHz – 6GHz Evaluation Board with 5-piece samples Functional Block Diagram Top View

Applications

• Cellular, 3G, 4G, 5G Infrastructure
• WiBro, WiMax, LTE
• Wireless Backhaul
• High Performance Communication Systems
• Test Equipment

5 MHz to 6 GHz Absorptive High Isolation SPDT Switch

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 2 of 13 www.qorvo.com Recommended Operating Conditions Parameter Min Typ Max Units Device Voltage (VDD) +2.5 +3.0 +5.5 V TCASE −40 +105 °C Tj for >105 hours MTTF +125 °C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Absolute Maximum Ratings Parameter Rating Storage Temperature −55 °C to +150 °C RF Input Power, CW, 50 Ω, T=25 °C +36 dBm Device Voltage (VDD) +6 V Control Voltage (VCTL, VEN) +6 V Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Electrical Specifications Parameter Conditions (1) Min Typ Max Units Operational Frequency Range 5 6000 MHz Insertion Loss (2) (RFC to RF1/RF2) 0.3 GHz 0.55 dB 1.0 GHz 0.60 dB 2.0 GHz 0.75 1.00 dB 3.0 GHz 0.90 dB 4.0 GHz 0.90 dB 5.0 GHz 1.10 dB Isolation (RFC to RF1/RF2)

0.3 GHz 75 dB

1.0 GHz 63 dB

2.0 GHz 53 60 dB

3.0 GHz 60 dB

4.0 GHz 60 dB

5.0 GHz 48 dB

(RF1 to RF2)

0.3 GHz 80 dB

1.0 GHz 70 dB

3.0 GHz 53 dB

4.0 GHz 48 dB

5.0 GHz 49 dB

(RF1/RF2 ON-State)

0.3 GHz 28 dB

1.0 GHz 27 dB

2.0 GHz 20 dB

3.0 GHz 20 dB

4.0 GHz 22 dB

5.0 GHz 17 dB

(RF1/RF2 OFF-State)

0.3 GHz 37 dB

1.0 GHz 36 dB

2.0 GHz 30 dB

3.0 GHz 27 dB

4.0 GHz 23 dB

5.0 GHz 20 dB

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 3 of 13 www.qorvo.com Electrical Specifications (Continued) Parameter Conditions (1) Min Typ Max Units Operational Frequency Range 5 6000 MHz Input IP3 1.0 GHz +12 dBm input power per-tone,

1 MHz tone spacing

2.0 GHz 55 65 dBm

Input 0.1 dB Compression Power 1.0 GHz 36 dBm Input 1 dB Compression Power 1.0 GHz 36 dBm Setting Time 50% VCTL to optimum functionality 1.5 3.0 μs Start-up Time 90% VDD to full functionality 25 50 μs Switching Time 50% control to 10/90% RF 250 ns 50% control to 2/98% RF 360 600 ns Supply Current (IDD) VDD 5.0V 140 200 μA Control Current, (ICTL, IEN) VCTL 5.0V 0.5 5.0 μA Low Control Voltage (VCTL) 1.8 V Logic compatible 0 0.63 V High Control Voltage (VCTL) 1.1 VDD V Notes: 1. Test conditions unless otherwise noted: VDD = +5.0 V, VCTL = 0/+5.0 V, Temp = +25 °C, 50 Ω system, RF ports DC Voltage 0V 2. PCB trace loss deducted. Maximum Operating Power at +85C, ≥300 MHz CW Input Port State VEN Power Thermal Resistance, θjc RFC, RF1 or RF2 ON Low 33.0 dBm (1) 97 °C/W (2) RFC Both OFF & RFC Reflective High 31.3 dBm N/A RF1 or RF2 OFF & Terminated (5) Low or High 26.0 dBm 100 °C/W RF1 and RF2 Both OFF & Terminated (5) High 27.8 dBm (3) 65 °C/W Notes: 1. Load VSWR ≤ 3:1; for higher load VSWR, the maximum Input power reduced to +30.5 dBm 2. Apply to resistive loss from the insertion loss not including mismatch loss 3. Total power on both RF1 and RF2 ports being driven simultaneously 4. For < 300 MHz, it is recommended to operate at least 4 dB below Input 1 dB Compression Power 5. Internally terminated Truth Table Control Input Signal Path State VCTL VEN RFC ⇆ RF1 RFC ⇆ RF2 0 0 OFF ON 1 0 ON OFF 0 1 OFF OFF 1 1 OFF OFF Notes: “0” = 0 V to 0.63 V; “1” = 1.1 V to VDD; VDD = 2.5 to 5.5 V must be applied for all valid states

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 4 of 13 www.qorvo.com

5 MHz to 6 GHz Evaluation Board – RFSW6024PCK-410

Bill of Material – RFSW6024PCK-410 Reference Des. Value Description Manuf. Part Number - - Printed Circuit Board Qorvo RFSW6224-410(A) U1 - SOI, High Isolation SPDT RF switch Qorvo RFSW6024 C2, C3, C4 (1) 100 pF CAP, 100 pF, 5%, 50V, C0G, 0402 Taiyo Yuden RM UMK105 CG101JV-F R2, R3, R5, R6, R7 0 Ω RES, 0 Ω, 50 Ω Max. Lead Free, 0402 KOA RK73Z1ETTP J1, J2, J3, J4, J5 SMA CONN, SMA, EL, Mini FLT 0.068”, SPE-000303 Aliner 20-001CF-T P1 - CONN, HDR, ST, PLRZD, 6-Pin, 0.100” AMP 640454-6 Note: 1. Optional

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 5 of 13 www.qorvo.com Performance Plots – RFSW6024PCK-410 Test conditions unless otherwise noted: VDD = +3.0 V, Temp.=+25 °C

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 6 of 13 www.qorvo.com Performance Plots – RFSW6024PCK-410 (Continued 1) Test conditions unless otherwise noted: VDD = +3.0 V, Temp.=+25 °C

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 7 of 13 www.qorvo.com Performance Plots – RFSW6024PCK-410 (Continued 2) Test conditions unless otherwise noted: VDD = +3.0 V, Temp.=+25 °C

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 8 of 13 www.qorvo.com Switching Time Plots Swithing Time (tOFF) = 234ns, 50% VCTL to 10% RF, +85°C Swithing Time (tON) = 284ns, 50% VCTL to 90% RF, +85°C Swithing Time (tOFF) = 218ns, 50% VCTL to 10% RF, +25°C Swithing Time (tON) = 286ns, 50% VCTL to 90% RF, +25°C Swithing Time (tOFF) = 212ns, 50% VCTL to 10% RF, -40°C Swithing Time (tON) = 280ns, 50% VCTL to 90% RF, -40°C

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 9 of 13 www.qorvo.com Pad Configuration and Description Top View Pad No. Label Description

1 VDD DC Supply Voltage Input

2 VCTL Logic Control Input, Logic High/Low sets the switch RFC-RF1/RF2 to “ON” state

3 RFC RF Common Port, DC blocking capacitor required if > 0.5 V external voltage is present 4, 8, 13, 16 NC No Internal Connection, External connection to PCB Ground Recommended to maximize isolation

5 VEN Logic Control Input, Logic High sets the switch both RF1 and RF2 to “OFF” state

6, 7, 10, 11, 14, 15 NC Ground or No Connection, External connection to PCB Ground Recommended to maximize isolation 9 RF1 RF Port 1, DC blocking capacitor required if > 0.5 V external voltage is present 12 RF2 RF Port 2, DC blocking capacitor required if > 0.5 V external voltage is present Backside Paddle GND RF and DC ground. Must be soldered on PCB ground plane over a bed of via holes to minimize inductance and thermal resistance

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 10 of 13 www.qorvo.com Package Marking and Dimensions Marking: Part Number – SW6024 Trace Code – Assigned by subcontractor Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. 3. Contact plating: NiPdAu PCB Mounting Pattern Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. 3. Via holes are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.01”). 4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 11 of 13 www.qorvo.com Tape and Reel Information – Carrier and Cover Tape Dimensions Feature Measure Symbol Size (in) Size (mm) Cavity Length A0 0.169 4.30 Width B0 0.169 4.30 Depth K0 0.049 1.25 Pitch P1 0.315 8.00 Centerline Distance Cavity to Perforation - Length Direction P2 0.079 2.00 Cavity to Perforation - Width Direction F 0.217 5.50 Cover Tape Width (Reference Only) C 0.362 9.20 Carrier Tape Width W 0.472 12.0

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 12 of 13 www.qorvo.com Tape and Reel Information – Reel Dimensions Standard T/R size = 2,500 pieces on a 13” reel. Feature Measure Symbol Size (in) Size (mm) Flange Diameter A 12.992 330.0 Thickness W2 0.717 18.2 Space Between Flange W1 0.504 12.8 Hub Outer Diameter N 4.016 102.0 Arbor Hole Diameter C 0.512 13.0 Key Slit Width B 0.079 2.0 Key Slit Diameter D 0.787 20.0 Tape and Reel Information – Tape Length and Label Placement Notes: 1. Empty part cavities at the trailing and leading ends are sealed with cover tape. See EIA 481-1-A. 2. Labels are placed on the flange opposite the sprockets in the carrier tape.

Datasheet, Rev. J, April 21, 2023 | Subject to change without notice 13 of 13 www.qorvo.com Handling Precautions Parameter Rating Standard Caution! ESD-Sensitive Device ESD – Human Body Model (HBM) Class 2 ESDA / JEDEC JS-001-2012 ESD – Charged Device Model (CDM) Class C3 JEDEC JESD22-C101F MSL – Moisture Sensitivity Level Level 1 IPC/JEDEC J-STD-020 Solderability Solder profiles available upon request. Contact plating: NiPdAu RoHS Compliance This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electr ical and Electronic Equipment) as amended by Directive 2015/863/EU. This product also has the following attributes:

• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• SVHC Free
• PFOS Free Important Notice The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information con tained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All informatio n contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anythin g described by such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Copyright 2023 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc. Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations: Web: www.qorvo.com Tel: 1-844-890-8163 Email: customer.support@qorvo.com Pb