RFF8216PCK-410

RFFM8216 QORVO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

2.4 GHz Integrated Wi-Fi Front-End Module

D DATA SHEET RFFM8216 | Subject to change without notice 1 of 11 www.qorvo.com ADVANCED Product Overview The RFFM8216 provides a complete integrated solution in a single front end module (FEM) for WiFi 802.11b/g/n/ac systems.Performance is focused on a balance of efficiency to enable long battery life and linear power that increases the range of connection. It is specifically designed to work with the RFFM8516 to greatly reduce BOM cost in dual band applications. The RFFM8216 integrates a 2.4GHz power amplifier (PA), single pole triple throw switch (SP3T), LNA with bypass + BT/Rx switch (SP2T), harmonic filtering, a diversity switch (SP2T) and a power detector coupler for improved accuracy. Functional Block Diagram Top View 16 Pin 2.3 x 2.3 mm QFN Package Key Features

• POUT = 20dBm, 802.11n 20MHz MCS7 @ 2.2% (-33dB) Dynamic EVM
• High efficiency
• Input and Output matched to 50 ohms
• Integrated 2.4GHz PA, SP3T, LNA with Bypass, 2xSPDT and PDET
• Integrated Power Detector
• High Impedance PA Enable

Applications

• IEEE 802.11b/g/n/ac WLAN Applications
• Single-Placement RF Front-End Module
• Single-band and Dual-band Wireless LAN Systems
• Portable Battery-Powered Equipment

Ordering Information

RFFM8216SB 5 piece sample bag RFFM8216SQ 25 piece sample bag RFFM8216SR 7” Reel with 100 pieces RFFM8216TR7 7” Reel with 2500 pieces RFFM8216TR7-5K 7” Reel with 5000 pieces RFF8216PCK-410 Full assembled Evaluation Board w/ 5-piece bag

2.4 GHz Wi-Fi Integrated Front-End Module

DATA SHEET RFFM8216 | Subject to change without notice 2 of 11 www.qorvo.com Absolute Maximum Ratings PARAMETER CONDITIONS RATING Storage Temperature -40 to 150 °C DC Supply Voltage No RF Applied −0.5 to +6.0 V PA Enable Voltage −0.5 to +5.0 V DC Supply Current 800mA RF Maximum Input Power (TX Mode) CW, 50Ω, VCC = 3.6 V, T = 25ºC +12 dBm RF Maximum Input Power (RX LNA Mode) CW, 50Ω, VCC = 3.6 V, T = 25ºC 0 dBm RF Maximum Input Power (RX BYPASS Mode) CW, 50Ω, VCC = 3.6 V, T = 25ºC +30 dBm Operation of this device outside the parameter ranges given above may cause permanent damage. Recommended Operating Conditions PARAMETER CONDITIONS MIN. TYP. MAX. UNITS Operating Temperature −20 - +60 oC Extended Operating Temperature Functional with reduced performance −40 - +85 oC Operating Voltage VCC 3.0 3.6 4.2 V Extended Operating Voltage VCC Functional with reduced performance 3.0 - 4.8 V Control Voltage (V-High) PAEN2 2.75 2.9 Vcc V Control Voltage (V-High) LNAEN2 2.75 3.3 Vcc V Control Voltage (V-Low) PAEN2 / LNAEN2 0 0.1 0.4 V Control Current (I-High) PAEN2 - 100 1000 uA Control Current (I-High) LNAEN2 - 50 1000 uA Control Current (I-Low) PAEN2 / LNAEN2 - 0.1 10 uA Leakage/Sleep/Bypass Mode Current PAEN2/ LNAEN2 = LOW VCC = 4.2 V - 8 16 uA Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions.

DATA SHEET RFFM8216 | Subject to change without notice 3 of 11 www.qorvo.com Logic Truth Table SINGLE BAND CONFIGURATION MODE PAEN2 LNAEN2

2.4 GHz TX Mode High Low

2.4 GHz RX LNA Mode Low High

2.4 GHz RX Bypass (Sleep) Low Low

5 GHz FEM 2 GHz FEM

MODE PAEN5 LNAEN5 SWCTL5 PAEN2 LNAEN2

5 GHz TX Mode High Low High Low Low

5 GHz RX LNA Mode Low High Low Low Low

5 GHz Sleep/Bypass Low Low Low Low Low

2.4 GHz TX Mode N/A N/A N/A High Low

2.4 GHz RX LNA Mode N/A N/A N/A Low High

2.4 GHz RX Bypass (Sleep) N/A N/A N/A Low Low

RFSW N/A N/A N/A Low High/Low

DATA SHEET RFFM8216 | Subject to change without notice 4 of 11 www.qorvo.com Electrical Specifications – Transmit (VCC = 3.6 V; Temp=25°C; unless noted otherwise) PARAMETER CONDITIONS MIN. TYP. MAX. UNITS Operating Frequency 2412 - 2472 MHz Small Signal Gain 24 28 - dB Gain flatness For any 20 MHz bandwidth −0.25 - +0.25 dB Gain flatness For entire frequency band −1 - +1 dB 11g 54 Mbps Output Power +19.5 +20.5 - dBm DEVM - −31 −28 dB MCS7 20 MHz Output Power +19.0 +20.0 - dBm DEVM - −33 −29 dB MCS8 20 MHz Output Power +18.0 +19.0 - dBm DEVM - - −35 dB Margin to Spectrum Emission Mask 11b 1 Mbps Pout = 24.0 dBm - 3.0 - dB Margin to Spectrum Emission Mask 11g 6 Mbps Pout = 22.0 dBm - 3.0 - dB Margin to Spectrum Emission Mask 11n, MCS0 HT20 Pout = 22.0 dBm - 3.0 - dB Current 11b, 1 Mbps Pout = 24.0 dBm - 320 350 mA Current 11n, MCS7 HT20 Pout = 20.0 dBm - 230 260 mA Return Loss RFIN Port 10 15 - dB Return Loss ANT Port 7 9 - dB Harmonics (2f0) 802.11b 1Mbps; Pout = 22.0 dBm - - −13 dBm/MHz Harmonics (3f0) 802.11b 1Mbps; Pout = 22.0 dBm - - −30 dBm/MHz Power Detector Voltage Pout = 5.0 dBm - 0.2 - V Pout = 24.0 dBm - - 1.1 V PA Switching Speed - 400 - nS ANT to RX Isolation (TX Mode) 40 45 - dB Electrical Specifications – RFSW (RFIN-RFSW) (VCC = 3.6 V; Temp=25°C; unless noted otherwise) PARAMETER CONDITIONS MIN. TYP. MAX. UNITS Operating Frequency 2412 - 2472 MHz Insertion Loss 2.4 GHz to 6 GHz - 0.7 1.5 dB RFIN Port Return Loss 10 15 - dB RFSW Port Return Loss 10 15 - dB Input P0.1dB 20 - - dBm

DATA SHEET RFFM8216 | Subject to change without notice 5 of 11 www.qorvo.com Electrical Specifications – Receive (VCC = 3.6 V; Temp=25°C; unless noted otherwise) PARAMETER CONDITIONS MIN. TYP. MAX. UNITS Operating Frequency 2412 - 2472 MHz Gain 12 14 - dB Gain flatness Over entire Frequency band −1 - +1 dB Noise Figure - 2.1 2.6 dB Current - 9 14 mA Input P1dB −10 −8 - dBm Return Loss RX Port 9 11 - dB Return Loss ANT Port 3 5 - dB LNA Switching Speed - 400 - nS Electrical Specifications – RX Bypass (VCC = 3.6 V; Temp=25°C; unless noted otherwise) PARAMETER CONDITIONS MIN. TYP. MAX. UNITS Operating Frequency 2412 - 2472 MHz Insertion Loss - 1.2 2.0 dB Return Loss RX Port 9 11 - dB Return Loss ANT Port 9 11 - dB Input P0.1dB 20 - - dBm

DATA SHEET RFFM8216 | Subject to change without notice 6 of 11 www.qorvo.com Application Circuit Schematic Bill of Materials REF. DES. QTY DESCRIPTION MANUF. PART NUMBER PCB 1 PCB, FM8216 Performance Micro International RFFM8216-410(B) C3 1 CAP, 4.7uF, +80/-20%, 10V, Y5V, 0805 Taiyo Yuden CE LMK212 F475ZG-T C4 1 Cap, 0.1uF, 10%, 6.3V, X5R, 0201 Murata Electronics GRM033R60J104KE19D C2 1 CAP, 1000pF, 10%, 25V, X7R, 0201 Samsung CL03B102KA3NNNC C1, C5, C6 3 CAP, 10pF, +/-0.5pF, 25V, C0G, 0201 Taiyo Yuden RM TMK063CG100DT-F L1 1 IND, 6.8nH, 5%, M/L, 0201 Taiyo Yuden LG HK06036N8J R1 1 RES, 3.9K, 5%, 1/20W, 0201 Kamaya RMC1/20-392JPA15 J1, J2, J3, J4 4 CONN, SMA, EL FLT VIPER, MAT-21-

1038 Amphenol RF Asia Corp 901-10425

P1, P2 2 CONN, HDR, ST, PLRZD, 3-PIN, 0.100" ITW Pancon MPSS100-3-C

DATA SHEET RFFM8216 | Subject to change without notice 7 of 11 www.qorvo.com Pin Configuration and Description Top View PIN NUMBER LABEL DESCRIPTION 1 LNAEN2 Logic Control voltage 2. See truth table for proper voltage settings. 2,9,10 VCC DC Power Supply Voltage

3 NC No Connection

4 RX RF output port for the 802.11b/g/n/ac LNA. This port is matched to 50Ω and DC blocked internally. 5 RFIN RF input port for the 802.11 diversity switch. This port is matched to 50Ω. An external DC block is required. 7 RFSW RF output port for the 5GHz front end module. This port is matched to 50Ω. An external DC block is required. 12 PDET Power Detector output. May need external series R/shunt C to adjust voltage level and to filter RF noise. 14 ANT RF bidirectional antenna port matched to 50Ω. An external DC block is required. 16 PAEN2 Logic Control voltage 1. See truth table for proper voltage settings. 6, 8, 11, 13, 15 GND RF and DC Ground Backside Pad GND Ground connection. The back side of the package should be connected to the ground plan though as short of a connection as possible. PCB vias under the device are required.

DATA SHEET RFFM8216 | Subject to change without notice 8 of 11 www.qorvo.com Timing Diagram VCC PAEN2 TX Signal TIME RFFM8216 Transmit Mode RF/DC Power ON/OFF Sequence Note: Observe the timing sequence shown in the diagram above and described below . DC, RF, and ON/OFF Time signal levels per datasheet specifications .

• Apply VCC prior to turning PA enable ON
• Turn PA enable ON prior to applying RF signal
• Turn RF signal OFF prior to turning PA enable OFF
• Turn PA enable OFF prior to turning VCC OFF
• TX/RX simultaneous transition is allowed LNAEN2 LNAEN2 logic state “LOW” during TX mode VCC ON RX Signal ≥ 0.2us TX ON RX OFF ≥ 0.2us

DATA SHEET RFFM8216 | Subject to change without notice 9 of 11 www.qorvo.com Package Outline Drawing Package Marking and Dimensions Marking: Part number – RFFM8216 Trace code – XXXX Notes: 1. All dimensions are in microns. Angles are in degrees. 2. Dimension and tolerance formats conform to ASME Y14.4M -1994. 3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.

DATA SHEET RFFM8216 | Subject to change without notice 10 of 11 www.qorvo.com Recommended PCB Patterns RECOMMENDED SOLDER MASK PATTERN RECOMMENDED LAND PATTERN

DATA SHEET RFFM8216 | Subject to change without notice 11 of 11 www.qorvo.com Handling Precautions PARAMETER RATING STANDARD Caution! ESD sensitive device ESD – Human Body Model (HBM) Class 1C ESD/JEDEC JS-001-2012 ESD – Charged Device Model (CDM) Class C3 JESD22-C101 Solderability Compatible with both lead-free (260 °C max. reflow temperature) and tin/lead (245 °C max. reflow temperature) soldering processes. Package lead plating: NiPdAu RoHS Compliance This part is compliant with the 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment), as amended by Directive 2015/863/EU.

• Lead free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• SVHC Free Pb