MCR22-6 KERSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
/C0077/C0067/C0082/C0050/C0050/C0045/C0054/C0044 /C0077/C0067/C0082/C0050/C0050/C0045/C0056 Preferred Device /C0083/C0101/C0110/C0115/C0105/C0116/C0105/C0118/C0101 /C0071/C0097/C0116/C0101 /C0083/C0105/C0108/C0105/C0099/C0111/C0110 /C0067/C0111/C0110/C0116/C0114/C0111/C0108/C0108/C0101/C0100 /C0082/C0101/C0099/C0116/C0105/C0102/C0105/C0101/C0114/C0115 Reverse Blocking Thyristors Designed and tested for repetitive peak operation required for CD ignition, fuel ignitors, flash circuits, motor controls and low-power switching applications.
150 Amperes for 2 µs Safe Area
Very Low Forward “On” V oltage at High Current Low-Cost TO-226AA (TO-92) Device Marking: Device Type, e.g., MCR22–6, Date Code MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off–State Voltage (RGK = IK, TJ = /C004240 to +110°C, Sine Wave, 50 to 60 Hz, Gate Open) MCR22–6 MCR22–8 VDRM, VRRM 400 600 Volts On-State Current RMS (180° Conduction Angles, TC = 80°C) IT(RMS) 1.5 Amps Peak Non-repetitive Surge Current, TA = 25°C (1/2 Cycle, Sine Wave, 60 Hz) ITSM Amps Circuit Fusing Considerations (t = 8.3 ms) I2t 0.9 A2s Forward Peak Gate Power (Pulse Width ≤ 1.0 /C0109sec, TA = 25°C) PGM 0.5 Watt Forward Average Gate Power (t = 8.3 msec, TA = 25°C) PG(AV) 0.1 Watt Forward Peak Gate Current (Pulse Width ≤ 1.0 µs, TA = 25°C) IFGM 0.2 Amp Reverse Peak Gate Voltage (Pulse Width ≤ 1.0 µs, TA = 25°C) VRGM 5.0 Volts Operating Junction Temperature Range @ Rated VRRM and VDRM TJ –40 to +110 Storage Temperature Range Tstg –40 to +150 (1) VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. SCRs
1.5 AMPERES RMS
Preferred devices are recommended choices for future use and best overall value. www.kersemi.com TO–92 (TO–226AA) CASE 029 STYLE 10 PIN ASSIGNMENT Gate Anode Cathode K G A See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet.
ORDERING INFORMATION
MCR22–6, MCR22–8 www.kersemi.com THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Thermal Resistance, Junction to Case R θJC °C/W Thermal Resistance, Junction to Ambient R θJA 160 °C/W Lead Solder Temperature (Lead Length /C0113 1/16″ from case, 10 s Max) TL +260
ELECTRICAL CHARACTERISTICS
(TC = 25°C unless otherwise noted.) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Peak Repetitive Forward or Reverse Blocking Current (VAK = Rated VDRM or VRRM ; RGK = 1000 Ohms) T C = 25°C TC = 110°C IDRM , IRRM 200 µA µA ON CHARACTERISTICS Peak Forward On–State Voltage(1) (ITM = 1 A Peak) VTM 1.2 1.7 Volts Gate Trigger Current (Continuous dc)(2) TC = 25°C (VAK = 6 Vdc, RL = 100 Ohms) T C = –40°C IGT 200 500 µA Gate Trigger Voltage (Continuous dc)(2) TC = 25°C (VAK = 7 Vdc, RL = 100 Ohms) T C = –40°C VGT 0.8 1.2 Volts Gate Non–Trigger Voltage(1) (VAK = 12 Vdc, RL = 100 Ohms) T C = 110°C VGD 0.1 Volts Holding Current (VAK = 12 Vdc, Gate Open) T C = 25°C Initiating Current = 200 mA T C = –40°C IH 2.0 5.0 mA DYNAMIC CHARACTERISTICS Critical Rate of Rise of Off–State Voltage (TC = 110°C) dv/dt V/µs (1) Pulse Width =1.0 ms, Duty Cycle /C01181%. (2) RGK Current not included in measurement.
Figure 1. Maximum Case Temperature Figure 2. Maximum Ambient Temperature
Figure 9. Device Positioning on Tape
- Maximum alignment deviation between leads not to be greater than 0.2 mm.
- Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm.
- Component lead to tape adhesion must meet the pull test requirements.
- Maximum non–cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
- Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
- No more than 1 consecutive missing component is permitted.
- A tape trailer and leader, having at least three feed holes is required before the first and after the last component.
- Splices will not interfere with the sprocket feed holes.
MCR22–6, MCR22–8 ORDERING & SHIPPING INFORMATION: MCR22 Series packaging options, Device Suffix U.S. Europe Equivalent Shipping Description of TO92 Tape Orientation MCR22–6,8 MCR22–6RLRA MCR22–6RLRP MCR22–8RL1 MCR22–8ZL1 Radial Tape and Reel (2K/Reel) Bulk in Box (5K/Box) Radial Tape and Reel (2K/Reel) Radial Tape and Fan Fold Box (2K/Box) Radial Tape and Fan Fold Box (2K/Box) Flat side of TO92 and adhesive tape visible N/A, Bulk Round side of TO92 and adhesive tape visible Round side of TO92 and adhesive tape visible Flat side of TO92 and adhesive tape visible PACKAGE DIMENSIONS NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. R A P J L B K G H SECTION X–X CV D N N XX SEATING PLANE DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.175 0.205 4.45 5.20 B 0.170 0.210 4.32 5.33 C 0.125 0.165 3.18 4.19 D 0.016 0.021 0.407 0.533 G 0.045 0.055 1.15 1.39 H 0.095 0.105 2.42 2.66 J 0.015 0.020 0.39 0.50 N 0.080 0.105 2.04 2.66 STYLE 10: PIN 1. CATHODE 2. GATE 3. ANODE TO–92 (TO–226AA) CASE 029–11 ISSUE AJ www.kersemi.com