UG544

UG544 SILABS | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 36

Technical content

UG544: KG100S Module Radio Board User's Guide A Wireless Starter Kit with the BRD4332A Radio Board is an ex- cellent starting point to get familiar with the KG100S for Amazon Sidewalk Module. It also provides the necessary tools for develop- ing an Amazon Sidewalk application. BRD4332A is a plug-in board for the Wireless Pro Kit Mainboard (BRD4002A) and the Wireless Starter Kit Mainboard (BRD4001A). It contains the KG100S module. The mainboards contain an on-board J-Link debugger with a Packet Trace Interface and a virtual COM port, enabling application development and debugging the attached radio board as well as external hardware. This document describes how to use the BRD4332A Radio Board together with a Wireless Pro Kit Mainboard or a Wireless Starter Kit Main- board. BRD4332A RADIO BOARD FEATURES

• KG100S module with 1 MB Flash, 96 kB RAM. Fully integrated RF matching network, crystals, and decoupling capacitors (KG100SAAMD) Inverted-F PCB antenna (2.4 GHz)
• SMA antenna connector (915 MHz) MAINBOARD FEATURES
• Advanced Energy Monitor
• Packet Trace Interface Logic analyzer (BRD4002A only)
• Virtual COM Port
• SEGGER J-Link on-board debugger
• External device debugging
• Ethernet and USB connectivity
• User LEDs / Pushbuttons
• 20-pin 2.54 mm EXP header
• Breakout pads for module I/O
• CR2032 coin cell battery support SOFTWARE SUPPORT
• Simplicity Studio
• Energy Profiler Network Analyzer

ORDERING INFORMATION

• KG100S-RB4332A silabs.com | Building a more connected world. Copyright © 2023 by Silicon Laboratories Rev. 1.0

silabs.com | Building a more connected world. Rev. 1.0 | 2

6.3.4 silabs.com | Building a more connected world. Rev. 1.0 | 3

1. Introduction The KG100S module is featured on a radio board that plugs directly into a Wireless Starter Kit (Wireless STK) Mainboard or a Wireless Pro Kit Mainboard. The mainboards feature several tools for easy evaluation and development of wireless applications. An on-board J- Link debugger enables programming and debugging on the target device over USB or Ethernet. The Advanced Energy Monitor (AEM) offers real-time current and voltage monitoring. A virtual COM port interface (VCOM) provides an easy-to-use serial port connection over USB or Ethernet. The Packet Trace Interface (PTI) offers invaluable debug information about transmitted and received packets in wireless links. All debug functionality, including AEM, VCOM, and PTI, can also be used towards external target hardware instead of the attached radio board. To further enhance its usability, the mainboard contains sensors and peripherals that demonstrate some of the many capabilities of the KG100S. The mainboard also has a 20-pin EXP header which can be used for connecting EXP boards to the kit or for easy connection to I/Os on the radio board target IC.

1.1 Radio Boards

A Wireless Pro Kit consists of one or more mainboards and radio boards that plug into the mainboard. Different radio boards are availa- ble, each featuring different Silicon Labs devices with different operating frequency bands. Because the mainboards are designed to work with different radio boards, the actual pin mapping from a device pin to a mainboard feature is done on the radio board. This means that each radio board has its own pin mapping to the Wireless Pro Kit features, such as buttons, LEDs, the display, the EXP header, and the breakout pads. Because this pin mapping is different for every radio board, it is important to consult the correct docu- ment, which shows the kit features in context of the radio board plugged in.

1.2 Mainboards

The KG100S Radio Board (BRD4332A) can be used with either a Wireless Starter Kit Mainboard (BRD4001A) or a Wireless Pro Kit Mainboard (BRD4002A). The Wireless Pro Kit Mainboard is the successor to the Wireless Starter Kit Mainboard, which comes with some improvements and added features including increased AEM measurement range and sample rate, variable VMCU voltage, joy- stick, a logic analyzer, and a Mini Simplicity Connector. Kit features, such as the Si7021 sensor and the EXP header, are available on the same KG100S pins regardless of the mainboard being used, but the pinout to the breakout pads differs. The combination of the KG100S Radio Board with either one of these mainboards is hereby referred to as a Wireless Pro Kit as the figure below illustrates. Wireless Starter Kit Mainboard (BRD4001A) Wireless Pro Kit Mainboard (BRD4002A) Radio Board (BRD4332A) Wireless Starter Kit Figure 1.1. Wireless Pro Kit Combinations Note: This document explains how to use the Wireless Pro Kit when the KG100S Radio Board (BRD4332A) is combined with either a Wireless Starter Kit Mainboard (BRD4001A) or a Wireless Pro Kit Mainboard (BRD4002A). Since some of the functionality of the kit depends on the type of mainboard used, it is important to consult the right information in the user guide whenever there are discrepan- cies. UG544: KG100S Module Radio Board User's Guide Introduction silabs.com | Building a more connected world. Rev. 1.0 | 4

1.3 Ordering Information

BRD4332A can be obtained as a separate radio board, KG100S-RB4332A. Table 1.1. Ordering Information Part Number Description Contents KG100S- RB4332A KG100S Radio Board 1x BRD4332A KG100S Radio Board

1.4 Getting Started

Detailed instructions for how to get started can be found on the Silicon Labs web pages: http://www.silabs.com/dev-tools. UG544: KG100S Module Radio Board User's Guide Introduction silabs.com | Building a more connected world. Rev. 1.0 | 5

1. Hardware Overview

2.1 Hardware Layout

of the KG100S Radio Board Wireless Pro Kit when the radio board is combined with a Wireless Pro Kit Mainboard (BRD4002A) or a Wireless STK Mainboard (BRD4001A) is shown below. Note: The LCD and joystick is not available on BRD4332A Note: The temp. sensor is not available on BRD4332A ARM Coresight 19-pin trace/debug header Simplicity Connector Plug-in Radio Board Si7021 Humidity and Temperature Sensor EXP-header for expansion boards Logic Analyzer Mini Simplicity Connector Radio Board Breakout Pads Battery or USB power Ultra-low-power 128x128 pixel memory LCD buttons, LEDs and joystick On-board USB and Ethernet J-Link Debugger - Virtual COM Port - Packet-trace - Advanced Energy Monitoring Figure 2.1. Hardware Layout With A Wireless Pro Kit Mainboard (BRD4002A) Radio Board Breakout Pads Plug-in Radio Board Si7021 Humidity and Temperature Sensor EXP-header for expansion boards ARM Coresight 19-pin trace/debug header Battery or USB power Ultra-low-power 128x128 pixel memory LCD buttons and LEDs On-board USB and Ethernet J-Link Debugger - Virtual COM Port - Packet-trace - Advanced Energy Monitoring Simplicity Connector Figure 2.2. Hardware Layout With A Wireless STK Mainboard (BRD4001A) UG544: KG100S Module Radio Board User's Guide Hardware Overview silabs.com | Building a more connected world. Rev. 1.0 | 6

2.2 Block Diagram

An overview of the KG100S Radio Board Wireless Pro Kit is shown in the figure below. KG100S PCB Module GPIO EXP Header User Buttons & LEDs GPIO

2.4 GHz RF

915 MHz RF SMA

Figure 2.3. Kit Block Diagram UG544: KG100S Module Radio Board User's Guide Hardware Overview silabs.com | Building a more connected world. Rev. 1.0 | 7

1. Connectors This chapter gives you an overview of the mainboard connectivity. The placement of the connectors on the Wireless Pro Kit Mainboard (BRD4002A) and the Wireless STK Mainboard (BRD4001A) is shown below. P101 GND GND VMCU VMCU F11 F10 F13 F12 P15 P14 P17 P16 P19 P18 P21 P20 GND GND P23 P22 VRF VRF GND GND P25 P24 P27 P26 P29 P28 P31 P30 P33 P32 P35 P34 P37 P36 P39 P38 P41 P40 P43 P42 P45 P44 GND GND F20 F19 3V3 3V3 Ethernet Connector J-Link USB Connector Radio Board Connectors Logic Analyzer Connector Mini Simplicty Connector Debug Connector Simplicity Connector EXP Header Figure 3.1. Wireless Pro Kit Mainboard (BRD4002A) Connector Layout Simplicity Connector Debug Connector Radio Board Connectors EXP Header GND GND VMCU VMCU P11 P10 P13 P12 P15 P14 P17 P16 P19 P18 P21 P20 GND GND P23 P22 VRF VRF GND GND P25 P24 P27 P26 P29 P28 P31 P30 P33 P32 P35 P34 P37 P36 P39 P38 P41 P40 P43 P42 P45 P44 GND GND NC NC 3V3 3V3 Ethernet Connector J-Link USB Connector Figure 3.2. Wireless STK Mainboard (BRD4001A) Connector Layout

3.1 J-Link USB Connector

USB connector is situated on the left side of the mainboard and provides access to the kit features described in Section 6. Board Controller through the USB interface. In addition to providing access to development features of the kit, this USB connector is also the main power source for the kit powering both the board controller and the AEM as described in Section 4. Power Supply and Reset.

3.2 Ethernet Connector

The Ethernet connector is situated on the left side of the mainboard and provides access to the kit features described in Section 6. Board Controller over TCP/IP. The J-Link USB connector must be connected while using this interface to provide power to the Wire- less Pro Kit as power is not supplied over the Ethernet connector. UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 8

3.3 Breakout Pads

the KG100S pins are routed from the radio board to breakout pads at the top and bottom edges of the mainboard. A 2.54 mm pitch pin header can be soldered on for easy access to the pins. The figures below show how the pins of the KG100S map to the pin numbers printed on the breakout pads on the Wireless Pro Kit Mainboard (BRD4002A) and the Wireless STK Mainboard (BRD4001A). To see the available functions on each pin, refer to the data sheet for KG100SAAMD. Note: Pinout to the breakout pads depends on the mainboard being used. GND VMCU P23 / NC P21 / NC P19 / NC P17 / NC GND P15 / NC F13 / GPIO0 / UIF_BUTTON1 F11 / GPIO0 / UIF_LED1 F9 / NC F7 / VCOM_RX / VCOM_RX F5 / NC F3 / NC F1 / DBG_SWCLK / DBG_SWCLK VRF GND VMCU NC / P22 NC / P20 NC / P18 NC / P16 GND NC / P14 UIF_BUTTON0 / GPIO1 / F12 UIF_LED0 / GPIO1 / F10 NC / F8 VCOM_TX / VCOM_TX / F6 RESET / RESET / F4 DBG_SWO / DBG_SWO / F2 DBG_SWDIO / DBG_SWDIO / F0 VRF BOTTOM EDGE GNDGND 5V5V F20 / PTI_DATA / PTI_DATAPTI_SYNC / PTI_SYNC / F19 P45 / NCNC / P44 P43 / NCNC / P42 P41 / NCNC / P40 3V33V3 P39 / NCNC / P38 P37 / NCNC / P36 P35 / NCNC / P34 P33 / NCNC / P32 P31 / NCNC / P30 P29 / NCNC / P28 P27 / NCNC / P26 P25 / NCNC / P24 GNDGND TOP EDGE Figure 3.3. Wireless Pro Kit Mainboard (BRD4002A) Breakout Pad Pin Mapping UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 9

P13 / I2C_SDA / I2C_SDA P11 / NC P9 / NC P7 / GPIO1 / UIF_BUTTON0_LED0 P5 / NC P3 / NC P1 / NC VRF GND VMCU NC / P22 NC / P20 NC / P18 NC / P16 GND NC / P14 I2C_SCL / I2C_SCL / P12 UIF_BUTTON1_LED1 / GPIO0 / P10 NC / P8 NC / P6 NC / P4 SX_DIO2 / SX_DIO2 / P2 NC / P0 VRF BOTTOM EDGE GNDGND 5V5V NCNC P45 / NCNC / P44 P43 / NCNC / P42 P41 / NCNC / P40 3V33V3 P39 / NCNC / P38 P37 / NCNC / P36 P35 / NCNC / P34 P33 / NCNC / P32 P31 / NCNC / P30 P29 / NCNC / P28 P27 / NCNC / P26 P25 / NCNC / P24 GNDGND TOP EDGE Figure 3.4. Wireless STK Mainboard (BRD4001A) Breakout Pad Pin Mapping UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 10

3.4 EXP Header

header is an angled, 20-pin expansion header that allows connection of peripherals or plugin boards to the kit. It is located on the right-hand side of the mainboard and contains several I/O pins that can be used with most of the KG100S features. Additionally, the VMCU, 3V3, and 5V power rails are also exposed. The connector follows a standard which ensures that commonly used peripherals, such as a SPI, a UART, and an I2C bus, are availa- ble on fixed locations in the connector. The rest of the pins are used for general purpose IO. This allows the definition of expansion boards (EXP boards) that can plug into several different Silicon Labs Starter Kits. The figure below shows the pin assignment of the EXP header. Because of limitations in the number of available GPIO pins, some of the EXP header pins are shared with kit features. 1314 1516 1718 20 19 VMCU NC NC NC GPIO1 / 13 NC NC I2C_SDA / 26 3V3 GND NC 12 / SX_DIO2 NC NC NC 9 / GPIO0 27 / I2C_SCL BOARD_ID_SDA BOARD_ID_SCL Reserved (Board Identification) KG100S I/O Pin Figure 3.5. EXP Header UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 11

3.4.1 EXP Header Pinout

on the KG100S is very flexible, so most peripherals can be routed to any pin. However, many pins are shared between the EXP header and other functions on the mainboard. The table below includes an overview of the mainboard features that share pins with the EXP header. Table 3.1. EXP Header Pinout Pin Connection EXP Header Function Shared Feature Peripheral Mapping 20 3V3 Board controller supply 18 5V Board USB voltage

16 I2C_SDA I2C_SDA

10 GPIO1 GPIO1 BUTTON0, LED0

2 VMCU KG100S voltage domain, included in AEM measurements. 19 BOARD_ID_SDA Connected to board controller for identification of add-on boards. 17 BOARD_ID_SCL Connected to board controller for identification of add-on boards.

15 I2C_SCL I2C_SCL

13 GPIO0 GPIO0 BUTTON1, LED1

5 SX_DIO2 SX_DIO2

1 GND Ground

UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 12

3.5 Logic Analyzer Connector

Pro Kit Mainboard includes an on-board, eight-channel logic analyzer. It enables four digital signals to be sampled and displayed in Simplicity Studio, in addition to the state of the on-board user interface LEDs and buttons. The logic analyzer is a good tool for correlating specific events to the AEM energy profile and packet trace data as these are time-synchronized and can be visualized together. The sampling rate of 100 kHz limits its use in decoding digital protocols like I2C or SPI. The logic analyzer connector is situated on the top right side of the Wireless Pro Kit Mainboard. Four signals (channel 0-3) can be connected to the logic analyzer using this connector and the test probes that are obtainable through the "Si-DA001A Pro Kit Mainboard Accessory Kit". The test probes can be connected to the kit itself or on an external board connected to the Wireless Pro Kit Mainboard. Note that in both cases the connected signals must be digital, and the voltages referenced to ground and VMCU on the Wireless Pro Kit Mainboard. The table below gives an overview of the logic analyzer signals. Note: The logic analyzer is only available on the Wireless Pro Kit Mainboard (BRD4002A). Using the external signals requires test probes which are obtainable through the "Si-DA001A Pro Kit Mainboard Accessory Kit". Table 3.2. Logic Analyzer Signal Description Type Channel Description External signal 0 Connector (ch0)

1 Connector (ch1)

2 Connector (ch2)

3 Connector (ch3)

5 LED1

6 BTN0

7 BTN1

UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 13

3.6 Debug Connector

connector serves multiple purposes based on the "debug mode" setting which can be configured in Simplicity Studio. When the debug mode is set to "Debug IN", the debug connector can be used to connect an external debugger to the KG100S on the radio board. When set to "Debug OUT", this connector allows the kit to be used as a debugger towards an external target. When set to "De- bug MCU" (default), the connector is isolated from both the on-board debugger and the radio board target device. Because this connector is electronically switched between the different operating modes, it can only be used when the board controller is powered (i.e., J-Link USB cable connected). If debug access to the target device is required when the board controller is unpowered, connect directly to the appropriate breakout pins. The pinout of the connector follows that of the standard ARM Cortex Debug+ETM 19-pin connector. The pinout is described in detail below. Even though the connector has support for both JTAG and ETM Trace, it does not necessarily mean that the kit or the on-board target device supports these features. 1 2 13 14 15 16 17 18 2019 TMS / SWDIO / C2D TCK / SWCLK / C2CK TDO / SWO TDI / C2Dps RESET / C2CKps GND NC NC GND GND GND GND VTARGET Cable Detect NC NC NC NC NC NC Figure 3.6. Debug Connector Note: The pinout matches the pinout of an ARM Cortex Debug+ETM connector, but these are not fully compatible because pin 7 is physically removed from the Cortex Debug+ETM connector. Some cables have a small plug that prevents them from being used when this pin is present. If this is the case, remove the plug or use a standard 2x10 1.27 mm straight cable instead. Table 3.3. Debug Connector Pin Descriptions Pin Number(s) Function Description 1 VTARGET Target reference voltage. Used for shifting logical signal levels between target and debugger.

2 TMS / SDWIO / C2D JTAG test mode select, Serial Wire data, or C2 data

4 TCK / SWCLK / C2CK JTAG test clock, Serial Wire clock, or C2 clock

6 TDO/SWO JTAG test data out or Serial Wire Output

8 TDI / C2Dps JTAG test data in or C2D "pin sharing" function

10 RESET / C2CKps Target device reset or C2CK "pin sharing" function

12 TRACECLK Not connected

14 TRACED0 Not connected

16 TRACED1 Not connected

18 TRACED2 Not connected

20 TRACED3 Not connected

9 Cable detect Connect to ground

7, 11, 13 NC Not connected 3, 5, 15, 17, 19 GND Ground UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 14

3.7 Simplicity Connector

Connector enables the advanced debugging features, such as the AEM, the virtual COM port, and the Packet Trace Interface, to be used towards an external target. The pinout is illustrated in the figure below. VMCU 1 33V3 55V 15GND 13GND 11GND 9GND 7GND 17BOARD_ID_SCL 19BOARD_ID_SDA

2 VCOM_TX

4 VCOM_RX

6 VCOM_CTS

8 VCOM_RTS

10 PTI0_SYNC

12 PTI0_ DATA

14 PTI0_CLK

16 PTI1_SYNC

18 PTI1_ DATA

20 PTI1_CLK

Figure 3.7. Simplicity Connector Note: Current drawn from the VMCU voltage pin is included in the AEM measurements, while the 3V3 and 5V voltage pins are not. When monitoring the current consumption of an external target with the AEM, unplug the radio board from the mainboard to avoid add- ing the radio board's current consumption to the measurements. Table 3.4. Simplicity Connector Pin Descriptions Pin Number(s) Function Description 1 VMCU 3.3 V power rail, monitored by the AEM 3 3V3 3.3 V power rail 5 5V 5 V power rail

2 VCOM_TX Virtual COM Tx

4 VCOM_RX Virtual COM Rx

6 VCOM_CTS Virtual COM CTS

8 VCOM_RTS Virtual COM RTS

10 PTI0_SYNC Packet Trace 0 Sync

12 PTI0_DATA Packet Trace 0 Data

14 PTI0_CLK Packet Trace 0 Clock

16 PTI1_SYNC Packet Trace 1 Sync

18 PTI1_DATA Packet Trace 1 Data

20 PTI1_CLK Packet Trace 1 Clock

17 BOARD_ID_SCL Board ID SCL

19 BOARD_ID_SDA Board ID SDA

7, 9, 11, 13, 15 GND Ground UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 15

3.8 Mini Simplicity Connector

Simplicity Connector on the Wireless Pro Kit Mainboard offers advanced debugging features on a 10-pin connector to be used towards an external target. The Mini Simplicity Connector offers the following features:

• Serial Wire Debug (SWD) with SWO
• Packet Trace Interface (PTI)
• Virtual COM port (VCOM)
• AEM monitored voltage rail VMCU 1 3RESET 5VCOM_TX 9PTI_FRAME 7SWDIO

2 GND

6 SWO

8 SWCLK

10 PTI_DATA

Figure 3.8. Mini Simplicity Connector Note: Current drawn from the VMCU voltage pin is included in the AEM measurements. When monitoring the current consumption of an external target with the AEM, unplug the radio board from the Wireless Pro Kit Mainboard to avoid adding the radio board's current consumption to the measurements. Table 3.5. Mini Simplicity Connector Pin Descriptions Pin Number(s) Function Description 1 VMCU Target voltage on the debugged application. Supplied and monitored by the AEM when power selection switch is in the "AEM" position.

2 GND Ground

3 RST Target device reset

5 VCOM_TX Virtual COM Tx

6 SWO Serial Wire Output

7 SWDIO Serial Wire Data

8 SWCLK Serial Wire Clock

9 PTI_FRAME Packet Trace Frame Signal

10 PTI_DATA Packet Trace Data Signal

Note: Mini Simplicity Connector pin-out is referenced from the device target side. UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 16

3.9 Debug Adapter

STK/WSTK Debug Adapter is an adapter board which plugs directly into the debug connector and the Simplicity Con- nector on the mainboard. It combines selected functionality from the two connectors to a smaller footprint 10-pin connector, which is more suitable for space-constrained designs. For versatility, the debug adapter features three different 10-pin debug connectors:

• Silicon Labs Mini Simplicity Connector
• ARM Cortex 10-pin Debug Connector
• Silicon Labs ISA3 Packet Trace The ARM Cortex 10-pin Debug Connector follows the standard Cortex pinout defined by ARM and allows the Wireless Pro Kit to be used to debug hardware designs that use this connector. The ISA3 connector follows the same pinout as the Packet Trace connector found on the Silicon Labs Ember Debug Adapter (ISA3). This enables using the Wireless Pro Kit to debug hardware designs that use this connector. The Mini Simplicity Connector is designed to offer advanced debug features from the kit on a 10-pin connector. The connector has the same pinout and functionality as described in 3.8 Mini Simplicity Connector. It is only necessary to use the debug adapter to get access to the Mini Simplicity Connector when using the Wireless STK Mainboard (BRD4001A). If using the Wireless Pro Kit Mainboard (BRD4002A), use the Mini Simplicity Connector on the mainboard instead. UG544: KG100S Module Radio Board User's Guide Connectors silabs.com | Building a more connected world. Rev. 1.0 | 17

1. Power Supply and Reset

4.1 Radio Board Power Selection

The KG100S on a Wireless Pro Kit can be powered by one of these sources:

• The debug USB cable A 3 V coin cell battery
• A USB regulator on the radio board (for devices with USB support only) The power source for the radio board is selected with the slide switch in the lower left corner of the Wireless STK Mainboard or the Wireless Pro Kit Mainboard. The figure below shows how the different power sources can be selected with the slide switch. VMCU AEM SELF (USB) BAT USB Connector Advanced Energy Monitor LDO KG100S

5 V VOUT

BAT SELF (USB)AEM

3 V Lithium Battery

(CR2032) Figure 4.1. Power Switch Note: The middle position is denoted by "USB" on the Wireless STK Mainboard, while it is denoted by "SELF" on the Wireless Pro Kit Mainboard. The slide switch functions the same on both mainboards. Note: The AEM can only measure the current consumption of the KG100S when the power selection switch is in the AEM position. AEM position: With the switch in the AEM position, a low noise low-dropout regulator (LDO) on the mainboard is used to power the radio board. This LDO is again powered from the debug USB cable. The AEM is now also connected in series, allowing accurate high- speed current measurements and energy debugging/profiling. USB position: With the switch in the USB position, radio boards with USB-support can be powered by a regulator on the radio board itself. BRD4332A does not contain a USB regulator, and setting the switch in the USB position will cause the KG100S to be unpowered. BAT position: With the switch in the BAT position, a 20 mm coin cell battery in the CR2032 socket can be used to power the device. With the switch in this position, no current measurements are active. This is the switch position that should be used when the radio board is powered with an external power source. The Wireless Pro Kit Mainboard (BRD4002A) features an additional 2-pin JST con- nector connected in paralell to the CR2032 socket that can be used with an external power source between 1.8 V and 3.6 V instead of a coin cell. The coin cell battery is not protected from reverse current, and it is therefore important to remove the coin cell battery from the CR2032 socket if applying external power. Note: The current sourcing capabilities of a coin cell battery might be too low to supply certain wireless applications. UG544: KG100S Module Radio Board User's Guide Power Supply and Reset silabs.com | Building a more connected world. Rev. 1.0 | 18

4.2 Kit Power

There are normally two main contributions to the power consumption from the mainboard USB connector, i.e., two main current paths:

• One being monitored by the AEM that goes to the target power domain (VMCU) One that goes to the board controller power domain While the current consumption of the board controller section is fairly deterministic and stable, the current consumption connected to the target’s power domain (VMCU) varies widely depending on the application and the slide switch position. Typically, the board con- troller power domain draws 200 mA on the Wireless Starter Kit Mainboard (BRD4001A) and 250 mA on the Wireless Pro Kit Mainboard (BRD4002A). The mainboards use linear regulators, and the recommended input voltage is 4.4 - 5.25 V. Use a USB host or power supply and cables that can deliver at least the total amount of current required by the kit. The 5V net exposed on the breakout pads, EXP header, and radio board is also sourced from the mainboard USB connector when the power select switch is in the AEM position. The 3V3 net exposed on the same peripherals is always sourced from the mainboard USB connector. The current consumption of these nets must be included in the total current consumption of the kit if these are utilized.

4.2.1 Board Controller Power

The board controller is responsible for important features, such as the debugger and the AEM, and is powered exclusively through the USB port in the top left corner of the board. This part of the kit resides on a separate power domain, so a different power source can be selected for the target device while retaining debugging functionality. This power domain is also isolated to prevent current leakage from the target power domain when power to the board controller is removed. The board controller power domain is not influenced by the position of the power switch. The kit has been carefully designed to keep the board controller and the target power domains isolated from each other as one of them powers down. This ensures that the target KG100S device will continue to operate in the BAT mode.

4.2.2 AEM Power

The supply for the target power domain (VMCU) is a linear regulator integrated with the AEM described in Section 7. Advanced Energy Monitor when the power select switch is in the AEM position. The output voltage of the regulator is fixed to 3.3 V on the Wireless STK Mainboard (BRD4001A), while it can be adjusted between 1.8 V and 3.6 V on the Wireless Pro Kit Mainboard (BRD4002A) using the admin console. The output current on the Wireless Pro Kit Mainboard (BRD4002A) is limited by an overcurrent protection (OCP) function, which de- pends on the programmed VMCU voltage: OCP (A) ≈ VMCU SET (V) x 0.2 (A/V). Approaching or exceeding the OCP limit is not recom- mended as the output voltage will be pulled low, which causes loss of function. The maximum recommended output current on the Wireless STK Mainboard (BRD4001A) is 300 mA.

4.3 KG100S Reset

The KG100S module can be reset by a few different sources:

• A user pressing the RESET button
• The on-board debugger pulling the #RESET pin low
• An external debugger pulling the #RESET pin low In addition to the reset sources mentioned above, a reset to the KG100S will also be issued during board controller boot-up. This means that removing power to the board controller (unplugging the J-Link USB cable) will not generate a reset but plugging the cable back in will as the board controller boots up. UG544: KG100S Module Radio Board User's Guide Power Supply and Reset silabs.com | Building a more connected world. Rev. 1.0 | 19

1. Peripherals The Wireless Pro Kit has a set of peripherals that showcase some of the KG100S features. Note that most KG100S I/Os routed to peripherals are also routed to the breakout pads or the EXP header, which must be taken into consideration when using these I/Os.

5.1 Push Buttons and LEDs

The kit has two user push buttons, marked BTN0 and BTN1, and two yellow LEDs, marked LED0 and LED1. BTN0 and LED0 share the connection to GPIO pin PB00, and BTN1 and LED1 are both connected to PB01. To use the push buttons as inputs to the KG100S, each button's GPIO pin must be configured as an input. Configure the pins as out- puts to control the LEDs. Note that LEDs are connected to GPIO pins in an active-low configuration. The push buttons are debounced by RC filters with a time constant of 1 ms. User Buttons & LEDs UIF_BUTTON0_LED0 UIF_BUTTON1_LED1 GPIO1 (GPIO) GPIO0 (GPIO) KG100S Figure 5.1. Buttons/LEDs UG544: KG100S Module Radio Board User's Guide Peripherals silabs.com | Building a more connected world. Rev. 1.0 | 20

5.2 Virtual COM Port

serial connection to the board controller is provided for application data transfer between a host PC and the target KG100S. This eliminates the need for an external serial port adapter. VCOM_ENABLE VCOM_TX (VCOM_TX) VCOM_RX (VCOM_RX) NC (tied high) VCOM_RX VCOM_TX Board Controller device USB Host PC Isolation & Level Shift NC NC VCOM_CTS VCOM_R TS ETH or Figure 5.2. Virtual COM Port Interface The virtual COM port consists of a physical UART between the target device and the board controller and a logical function in the board controller that makes the serial port available to the host PC over USB or Ethernet. The UART interface consists of four pins and an enable signal. Table 5.1. Virtual COM Port Interface Pins Signal Description VCOM_TX Transmit data from the KG100S to the board controller VCOM_RX Receive data from the board controller to the KG100S VCOM_CTS Clear to Send hardware flow control input, asserted by the board controller when it is ready to receive more data VCOM_RTS Request to Send hardware flow control output, asserted by the KG100S when it is ready to receive more data VCOM_ENABLE Enables the VCOM interface, allowing data to pass through to the board controller The parameters of the serial port, such as baud rate or flow control, can be configured using the admin console. The default settings depend on which radio board is used with the mainboard. Note: The VCOM port is only available when the board controller is powered, which requires the J-Link USB cable to be inserted. Note: There may be slight differences on the terminal prompt and settings between the Wireless Starter Kit Mainboard and the Wire- less Pro Kit Mainboard. UG544: KG100S Module Radio Board User's Guide Peripherals silabs.com | Building a more connected world. Rev. 1.0 | 21

5.2.1 Host Interfaces

be exchanged between the board controller and the target device through the VCOM interface, which is then available to the user in two different ways:

• Virtual COM port using a standard USB-CDC driver
• TCP/IP by connecting to the Wireless STK on TCP/IP port 4901 with a Telnet client When connecting via USB, the device should automatically show up as a COM port. The actual device name that is associated with the kit depends on the operating system and how many devices are or have been connected previously. The following are examples of what the device might show up as:
• JLink CDC UART Port (COM5) on Windows hosts
• /dev/cu.usbmodem1411 on macOS
• /dev/ttyACM0 on Linux Data sent by the target device into the VCOM interface can be read from the COM port, and data written to the port is transmitted to the target device. Connecting to the Wireless STK on port 4901 gives access to the same data over TCP/IP. Data written into the VCOM interface by the target device can be read from the socket, and data written into the socket is transmitted to the target device. Note: Only one of these interfaces can be used at the same time, with the TCP/IP socket taking priority. This means that if a socket is connected to port 4901, no data can be sent or received on the USB COM port.

5.2.2 Serial Configuration

By default, the VCOM serial port is configured to use 115200 8N1 (115.2 kbit/s, 8 data bits, 1 stop bit), with flow control disabled/ignor- ed. The configuration can be changed using the admin console: WPK> serial vcom config Usage: serial vcom config [--nostore] [handshake <rts/cts/rtscts/disable/auto>] [speed <9600,921600>] Using this command, the baud rate can be configured between 9600 and 921600 bit/s, and hardware handshake can be enabled or disabled on either or both flow control pins. UG544: KG100S Module Radio Board User's Guide Peripherals silabs.com | Building a more connected world. Rev. 1.0 | 22

1. Board Controller

6.1 Introduction

STK Mainboard and the Wireless Pro Kit Mainboard contain a dedicated microcontroller for some of the advanced kit features provided. This microcontroller is referred to as the board controller and is not programmable by the user. The board controller acts as an interface between the host PC and the target device on the radio board, as well as handling some housekeeping functions on the board. Note: This chapter describes the board controller on both the Wireless Starter Kit Mainboard and the Wireless Pro Kit Mainboard. There might be slight differences between these two boards, such as the exact menu and format on the admin console, not highlighted in this chapter. The logic analyzer is furthermore only available on BRD4002A. Some of the kit features actively managed by the board controller are:

• The on-board debugger, which can flash and debug both on-board and external targets.
• The Advanced Energy Monitor, which provides real-time energy profiling of the user application.
• The Packet Trace Interface, which is used in conjunction with PC software to provide detailed insight into an active radio network.
• The logic analyzer, which can capture digital signals time-synchronized to the energy profiling and packet trace data.
• The Virtual COM Port and Virtual UART interfaces, which provide ways to transfer application data between the host PC and the target processor.
• The admin console, which provides configuration of the various board features. Silicon Labs publishes updates to the board controller firmware in the form of firmware upgrade packages. These updates may enable new features or fix issues. See Section 9.1 Firmware Upgrades for details on firmware upgrade.

6.2 Admin Console

The admin console is a command line interface to the board controller on the kit. It provides functionality for configuring the kit behavior and retrieving configuration and operational parameters.

6.2.1 Connecting

The admin console is available when the Wireless Pro Kit is connected to Ethernet using the Ethernet connector in the top left corner of the mainboard. See Section 8.1.2 Ethernet Interface for details on the Ethernet connectivity. Connect to the admin console by opening a telnet connection to the kit's IP address, port number 4902. When successfully connected, a WPK> prompt is displayed. UG544: KG100S Module Radio Board User's Guide Board Controller silabs.com | Building a more connected world. Rev. 1.0 | 23

6.2.2 Built-in Help

console has a built-in help system which is accessed by the help command. The help command will print a list of all top level commands: WPK> help aem AEM Configuration and Information Commands [ avg, calibrate, calinfo ] boardid Commands for board ID probe. [ list, probe ] dbg Debug interface status and control [ info, mode ] dch Datachannel control and info commands [ info, message ] discovery Discovery service commands. [ key ] net Network commands. [ dnslookup, ip, mac ] pti Packet trace interface status and control [ config, disable, dump, ... ] quit Exit from shell serial Serial channel commands [ vcom ] sys System commands [ crashlog, nickname, reset, ... ] target Target commands. [ button, go, halt, ... ] time Time Sync Service commands [ client, disable, info, ... ] user User management functions [ login,] The help command can be used in conjunction with any top level command to get a list of sub-commands with descriptions. For exam- ple, pti help will print a list of all available sub-commands of pti: WPK> pti help config Configure packet trace disable Disable packet trace dump Dump PTI packets to the console as they come enable Enable packet trace info Packet trace state information This means that running pti enable will enable packet trace.

6.2.3 Command Examples

pti config 0 efruart 1600000 Configures PTI to use the "EFRUART" mode at 1.6 Mb/s. Serial Port Configuration serial config vcom handshake enable Enables hardware handshake on the VCOM UART connection.

6.3 Virtual UART

The Virtual UART (VUART) interface provides a high-performance application data interface that does not require additional I/O pins apart from the debug interface. The Wireless STK makes the VUART interface available on TCP/IP port 4900.

6.3.1 Target-to-Host

Target-to-host communication utilizes the SWO-pin of the debug interface through the ITM debug peripheral. This approach allows a sleepy target device to enter all energy modes and still wake up intermittently to send debug information. The baud rate of the SWO data is locked to 875 kHz. VUART utilizes ITM stimulus port 0 for general purpose printing. Silicon Labs' networking stacks utilize ITM stimulus port 8 for debug printing. The data on port 8 is encapsulated in additional framing and will also appear in the Simplicity Studio Network Analyzer. UG544: KG100S Module Radio Board User's Guide Board Controller silabs.com | Building a more connected world. Rev. 1.0 | 24

6.3.2 Host-to-Target

Host-to-target communication utilizes SEGGER's Real Time Transfer (RTT) technology. A full explanation of how this works can be found in J-Link/J-Trace User Guide (UM08001). Briefly summarized, RTT consists of a structure called the RTT Control Block, which is located in RAM. This control block points to circular buffers that the debugger can write data into. The target application can then read data out of this circular buffer. The board controller will start searching for the RTT Control Block upon receiving data on TCP/IP port 4900. If the board controller is unable to locate the RTT Control Block, it will return an error message on the same connection. For the board controller to be able to locate the RTT Control Block, it has to be aligned on a 1024-byte boundary in RAM. After initializing the RTT connection, the target will only enter emulated EM2 and EM3 where the power consumption remains similar to EM1. This is because RTT utilizes the debug interface, which requires use of high-frequency oscillators. Energy modes EM4S and EM4H will work as normal. When debugging energy consumption, it is therefore important to not send data on TCP/IP port 4900 as not to instantiate the RTT connection.

6.3.3 Limitations

• Because the SWO-connection can be disabled by the debugger at will, it is important for the target application to verify that SWO is enabled and configured before each transmission on the interface.
• After initializing host-to-target communication over RTT by sending data on TCP/IP port 4900, the target application will be unable to enter EM2 and EM3. This is because RTT utilizes the debug connection of the target.
• VUART might not work reliably during an active debugging session. This is because there is contention over the target's debug inter- face. The board controller will defer accessing the target until it is made available by the host debugger.
• VUART is designed with the assumption that only the board controller will access the RTT control block. If the target application uses RTT for other purposes, such as Segger SystemView, refrain from using VUART.

6.3.4 Troubleshooting

No data received after ending a debug session. After certain debugger operations, the host computer manually disables SWO on the target to con- serve power. This might cause SWO data to not appear if the target application initialized SWO be- fore the debugger has disconnected. Either press the RESET button on the Wireless Starter Kit to reset the target application or make sure that the target application verifies that SWO is enabled and configured before sending any data. No data received after flashing a new application. Other issues Disconnect from TCP port 4900, press the RESET button on the kit, then reconnect to 4900. If this does not fix the issue, try to restart the kit by unplugging and replugging the USB cable. UG544: KG100S Module Radio Board User's Guide Board Controller silabs.com | Building a more connected world. Rev. 1.0 | 25

1. Advanced Energy Monitor

7.1 Introduction

developer seeking to make their embedded code spend as little energy as the underlying architecture supports needs tools to easily and quickly discover inefficiencies in the running application. This is what the Simplicity Energy Profiler is designed to do. In real-time, the Energy Profiler will graph and log current as a function of time while correlating this to the actual target application code running on the KG100S. There are multiple features in the profiler software that allow for easy analysis, such as markers and statistics on selected regions of the current graph or aggregate energy usage by different parts of the application. The Energy Profiler is available through Simplicity Studio.

7.2 Code Correlation

By using the Energy Profiler, current consumption and voltage can be measured and linked to the actual code running on the KG100S in realtime. The Energy Profiler gets its data from the board controller on the mainboard through the Advanced Energy Monitor (AEM). The current signal is combined with the target processor's Program Counter (PC) sampling by utilizing a feature of the ARM CoreSight debug architecture, and the Instrumentation Trace Macrocell (ITM) block can be programmed to sample the MCU's PC at periodic inter- vals and output these over SWO pin ARM devices. When these two data streams are fused and correlated with the running applica- tion's memory map, an accurate statistical profile can be built that shows the energy profile of the running application in real-time.

7.3 AEM Circuit

The AEM circuit on the Wireless Pro Kit Mainboard (BRD4002A) and the Wireless STK Mainboard (BRD4001A) measures the current through a sense resistor inside the feedback loop of an LDO. The output voltage of this LDO powers the KG100S when the power slide switch is in the AEM position. AEM usage on both mainboards is similar, but the implementation and perfomance on the Wireless Pro Kit Mainboard (BRD4002A) has some key differences, including the utilization of two sense resistors instead of one, and a different LDO, which is explained in Section 7.3.1 AEM Details . The AEM implementation on the Wireless Pro Kit Mainboard (BRD4002A) is shown in the figure below. Power Select Switch VMCU Sense Resistors Current Sense Amplifier Multiple Gain Stages AEM Processing LDO KG100S Peripherals 0.5 Ω 5 V 10 Ω High Range Calibrate Figure 7.1. Advanced Energy Monitor On The Wireless Pro Kit Mainboard (BRD4002A) Note: The VMCU regulator feedback point is after the sense resistor to ensure that the VMCU voltage is kept constant when the output current changes. Series resistances in the current path will, however, cause some IR drop on VMCU. Note: The AEM circuit only works when the kit is powered and the power switch is in the AEM position. UG544: KG100S Module Radio Board User's Guide Advanced Energy Monitor silabs.com | Building a more connected world. Rev. 1.0 | 26

7.3.1 AEM Details

differences between the AEM on the Wireless Pro Kit Mainboard (BRD4002A) and the Wireless STK Mainboard (BRD4001A) is summarized in the table below with more in-depth information given in the text to follow. Table 7.1. Advanced Energy Monitor Parameters Parameter BRD4002A BRD4001A Voltage 1.8 - 3.6 V 3.3 V Sample Rate 100 kHz 10 kHz Sense Resistor 10.5 Ω / 0.5 Ω 2.35 Ω Measurement Range1 0 - 495 mA 0 - 95 mA Note: 1. The current sourcing capabilities of the LDO may be different than the measurement range. Wireless Pro Kit Mainboard (BRD4002A) AEM Design Details The AEM circuitry on the Wireless Pro Kit Mainboard is capable of measuring current signals in the range of approximately 0.1 µA to 495 mA. This is accomplished through a combination of a highly capable current sense amplifier, multiple sense resistors and gain stages, and signal processing within the kit's board controller before the current sense signal is read by a host computer with 100 kHz sample rate for display and/or storage. Averaging on the output data may be required to achieve sufficient accuracy in some situations, such as low currents, which can be traded for lower bandwidth. High current applications require that the regulator is able to supply enough current as described in Section 4.2 Kit Power. At low currents the current sense amplifier measures the voltage drop over a 10.5 Ω resistive path. The gain stage further amplifies this voltage with two different parallel gain settings to obtain two current ranges. The transition between these two ranges occurs around 150 µA. When the current exceeds a threshold, which is typically between 10 and 30 mA, the AEM circuitry switches from the 10.5 Ω resistive path to a 0.5 Ω sense resistor and is now capable of measuring currents up to approximately 495 mA. Should the current drop below the threshold again, the sense resistor is changed back to the 10.5 Ω resistive path and the AEM is back to using two different gain stages depending on whether the current is above or below 150 µA. The expected typical accuracy of the AEM on the Wireless Pro Kit Mainboard is within 1 %, except for currents in the low tens of micro- amps where offset errors start to dominate. In this low current region, the expected typical accuracy is some hundred nanoamps. At kit power-up or on a power-cycle, an automatic AEM calibration is performed which compensates for offset errors in the current sense amplifiers. To achieve the stated accuracy, averaging of the AEM output data is required in certain situations (typically at low currents and close to the bottom of the measurement ranges) to reduce noise. Averaging can be applied in the Energy Profiler to suit different requirements during or after the acquisition. The analog bandwidth of the measurement circuit depends on multiple factors, such as output current and capacitance on the VMCU net, and may be lower than the output data rate. Generally, higher output current and lower capacitance on VMCU gives a higher analog bandwidth. Wireless STK Mainboard (BRD4001A) AEM Design Details The AEM circuitry on the Wireless STK Mainboard works conceptually in a similar way to the implementation on the Wireless Pro Kit Mainboard except for two key differences: it uses only one 2.35 Ω sense resistor and the LDO is different. For details about the two implementations, the reader is encouraged to see the schematics. The AEM on the Wireless STK Mainboard is capable of measuring currents in the range of 0.1 µA to 95 mA. The second stage amplifier amplifies the signal with two different gain settings with the transition occurring around 250 µA. For currents above 250 µA, the AEM is accurate within 0.1 mA. When measuring currents below 250 µA, the accuracy increases to 1 µA. Even though the absolute accuracy is 1 µA in the sub 250 µA range, the AEM can detect changes in the current consumption as small as 0.1 µA. It is possible to source currents above the measurement range as decribed in Section 4.2 Kit Power. The board controller outputs the AEM data with 10 kHz sample rate. UG544: KG100S Module Radio Board User's Guide Advanced Energy Monitor silabs.com | Building a more connected world. Rev. 1.0 | 27

1. On-Board Debugger The Wireless Pro Kit Mainboard and the Wireless STK Mainboard contain an integrated debugger, which can be used to download code and debug the KG100S. In addition to programming a target on a plug-in radio board, the debugger can also be used to program and debug external Silicon Labs EFM32, EFM8, EZR32, and EFR32 devices connected through the debug connector. The debugger supports three different debug interfaces for Silicon Labs devices:

• Serial Wire Debug is supported by all EFM32, EFR32, and EZR32 devices
• JTAG is supported by EFR32 and some EFM32 devices
• C2 Debug is supported by EFM8 devices For debugging to work properly, make sure the selected debug interface is supported by the target device. The debug connector on the board supports all three of these modes.

8.1 Host Interfaces

The Wireless Pro Kit supports connecting to the on-board debugger using either Ethernet or USB. Many tools support connecting to a debugger using either USB or Ethernet. When connected over USB, the kit is identified by its J-Link serial number. When connected over Ethernet, the kit is normally identified by its IP address. Some tools also support using the serial number when connecting over Ethernet; however, this typically requires the computer and the kit to be on the same subnet for the dis- covery protocol (using UDP broadcast packets) to work.

8.1.1 USB Interface

The USB interface is available whenever the USB connector on the left-hand side of the mainboard is connected to a computer.

8.1.2 Ethernet Interface

The Ethernet interface is available when the mainboard Ethernet connector in the top left corner is connected to a network. Normally, the kit will receive an IP address from a local DHCP server, and the IP address is printed on the LCD display. If your network does not have a DHCP server, you need to connect to the kit via USB and set the IP address manually using Simplicity Studio, Simplicity Commander, or J-Link Configurator. For the Ethernet connectivity to work, the kit must still be powered through the mainboard USB connector.

8.1.3 Serial Number Identification

All Silicon Labs kits have a unique J-Link serial number which identifies the kit to PC applications. This number is 9 digits and is normal- ly on the form 44xxxxxxx. The J-Link serial number is normally printed at the bottom of the kit LCD display. UG544: KG100S Module Radio Board User's Guide On-Board Debugger silabs.com | Building a more connected world. Rev. 1.0 | 28

8.2 Debug Modes

can be used in various debug modes as explained in this chapter. The on-board debugger can be used to debug the KG100S on the radio board, or it can be used to debug a supported external target board using either the debug connector or the Mini Simplicity Connector. An external debugger can furthermore be used to debug the KG100S on the radio board using the debug connector. Select- ing the active debug mode is done in Simplicity Studio. Note: The Wireless Starter Kit Mainboard (BRD4001A) does not feature a Mini Simplicity Connector; therefore, debugging an external target board directly over the Mini Simplicity Connector is not supported on this mainboard. However, it is possible to debug an external target that uses a Mini Simplicity Connector from the Wireless Starter Kit Mainboard by using a BRD8010A STK/WSTK Debug Adapter. Debug MCU: In this mode, the on-board debugger is connected to the KG100S on the kit. To use this mode, set the debug mode to [MCU]. RADIO BOARDBoard Controller USBHost Computer DEBUG HEADER External Hardware Figure 8.1. Debug MCU Debug OUT: In this mode, the on-board debugger can be used to debug a supported Silicon Labs device mounted on a custom board using the debug connector. To use this mode, set the debug mode to [Out]. Board Controller USBHost Computer DEBUG HEADER External Hardware RADIO BOARD Figure 8.2. Debug OUT Debug IN: In this mode, the on-board debugger is disconnected and an external debugger can be used to debug the KG100S on the kit over the debug connector. To use this mode, set the debug mode to [In UG544: KG100S Module Radio Board User's Guide On-Board Debugger silabs.com | Building a more connected world. Rev. 1.0 | 29

Figure 8.3. Debug IN Note: For "Debug IN" to work, the kit board controller must be powered through the Debug USB connector. Debug MINI: The Wireless Pro Kit mainboard features a dedicated Mini Simplicity Connector on the board. In this mode, the on-board debugger can be used to debug a supported Silicon Labs device mounted on a custom board over Serial Wire Debug. Virtual COM port and Packet Trace Interface is also available in this mode. To use this mode, set the debug mode to [Mini]. Board Controller USBHost Computer MINI SIMPLICITY CONNECTOR External Hardware RADIO BOARD Figure 8.4. Mini Out

8.3 Debugging During Battery Operation

KG100S is battery-powered and the J-Link USB is still connected, the on-board debug functionality is available. If the USB power is disconnected, the Debug IN mode will stop working. If debug access is required when the target is running off another energy source, such as a battery, and the board controller is powered down, make direct connections to the GPIOs used for debugging, which are exposed on the breakout pads. UG544: KG100S Module Radio Board User's Guide On-Board Debugger silabs.com | Building a more connected world. Rev. 1.0 | 30

1. Kit Configuration and Upgrades The kit configuration dialog in Simplicity Studio allows you to change the J-Link adapter debug mode, upgrade its firmware, and change other configuration settings. To download Simplicity Studio, go to silabs.com/simplicity. In the main window of the Simplicity Studio's Launcher perspective, the debug mode and firmware version of the selected J-Link adapt- er are shown. Click the [Change] link next to any of these settings to open the kit configuration dialog. Figure 9.1. Simplicity Studio Kit Information Figure 9.2. Kit Configuration Dialog

9.1 Firmware Upgrades

You can upgrade the kit firmware through Simplicity Studio. Simplicity Studio will automatically check for new updates on startup. You can also use the kit configuration dialog for manual upgrades. Click the [ Browse] button in the [Update Adapter ] section to select the correct file ending in .emz. Then, click the [Install Package] button. UG544: KG100S Module Radio Board User's Guide Kit Configuration and Upgrades silabs.com | Building a more connected world. Rev. 1.0 | 31

1. Schematics, Assembly Drawings, and BOM Schematics, assembly drawings, and bill of materials (BOM) are available through Simplicity Studio when the kit documentation pack- age has been installed. They are also available from the kit page on the Silicon Labs website: silabs.com. UG544: KG100S Module Radio Board User's Guide Schematics, Assembly Drawings, and BOM silabs.com | Building a more connected world. Rev. 1.0 | 32

1. Radio Board Revision History and Errata

11.1 BRD4332A Revision History

The Radio Board revision is printed on the backside of the board. Table 11.1. BRD4332A Revision History Radio Board Revision Release Date Description A03 6 Feb 2023 Initial release with BRD4332A Rev. A03.

11.2 BRD4332A Errata

Table 11.2. BRD4332A Errata Radio Board Revision Problem Description A03 VCOM access with BRD4001A VCOM is not supported when used with a BRD4001A. UG544: KG100S Module Radio Board User's Guide Radio Board Revision History and Errata silabs.com | Building a more connected world. Rev. 1.0 | 33

1. Kit Revision History The kit revision can be found printed on the kit packaging label, as outlined in the figure below. The revision history given in this section may not list every kit revision. Revisions with minor changes may be omitted. KG100S-RB4332A KG100S Radio Board 224400026 06-02-2023 A03 Figure 12.1. Kit Label

12.1 KG100S-RB4332A Revision History

Kit Revision Released Description A03 6 Feb 2023 Initial release with BRD4332A Rev. A03. UG544: KG100S Module Radio Board User's Guide Kit Revision History silabs.com | Building a more connected world. Rev. 1.0 | 34

1. Document Revision History Revision 1.0 April 2023

• Initial document release. UG544: KG100S Module Radio Board User's Guide Document Revision History silabs.com | Building a more connected world. Rev. 1.0 | 35

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701 USA www.silabs.com IoT Portfolio www.silabs.com/IoT SW/HW www.silabs.com/simplicity Quality www.silabs.com/quality Support & Community www.silabs.com/community Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software imple - menters using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and “Typical” parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance of the product. Silicon Labs shall have no liability for the consequences of use of the infor - mation supplied in this document. This document does not imply or expressly grant any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required or Life Support Systems without the specific written consent of Silicon Labs. A “Life Support System” is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications. Note: This content may contain offensive terminology that is now obsolete. Silicon Labs is replacing these terms with inclusive language wherever possible. For more information, visit www.silabs.com/about-us/inclusive-lexicon-project Trademark Information Silicon Laboratories Inc. ®, Silicon Laboratories ®, Silicon Labs ®, SiLabs ® and the Silicon Labs logo ®, Bluegiga ®, Bluegiga Logo ®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, “the world’s most energy friendly microcontrollers”, Redpine Signals ®, WiSeConnect , n-Link, ThreadArch ®, EZLink®, EZRadio®, EZRadioPRO ®, Gecko®, Gecko OS, Gecko OS Studio, Precision32 ®, Simplicity Studio ®, Telegesis, the Telegesis Logo ®, USBXpress ® , Zentri, the Zentri logo and Zentri DMS, Z-Wave ®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders.