CPT007B

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 31

Technical content

Features

Lowest power mode with feature operational: Input Engine with

7 Inputs

Optimized ActiveActive Low Power Sleep This information applies to a product under development. Its characteristics and specifications are subject to change without notice.

1. Feature List and Ordering Information The CPT007B has the following features:

• Capacitive sensing input engine with 7 inputs
• Post-sample touch qualification engine
• Configuration profile space in non-volatile memory
• Pin output with configurable polarity and drive strength
• Low power state machine to minimize current draw in all use cases
• Capacitive proximity sensing input
• Buzzer output
• Mutually exclusive touch qualifier
• Touch time-out timer 07T –0 B A – R Tape and Reel (Optional) Firmware Revision Hardware Revision Capacitive Sense Features — Button (B) Interface Type — GPO (0), I2C (1) Number of Capacitive Sense Inputs 01CP G M Temperature Grade — –40 to +85 °C (G) Silicon Labs Xpress Product Line TouchXpress Family Figure 1.1. CPT007B Part Numbering CPT007B Data Sheet Feature List and Ordering Information

1. Typical Connection Diagrams

2.1 Signal, Analog, and Power Connections

Figure 2.1 Connection Diagram on page 2 shows a typical connection diagram for the power pins of CPT007B devices. CPT007B Device 4.7 µF and 0.1 µF bypass capacitors required for the power pins placed as close to the pins as possible. 1.8-3.6 V (in) Host Processor ... 1.8-3.6 V (in) Electrode Electrode ... GND VDD OUT00 OUT06 CS06 CS00 Config Data Config Clk / RSTb OUT01 Figure 2.1. Connection Diagram CPT007B Data Sheet Typical Connection Diagrams

2.2 Configuration

The diagram below shows a typical connection diagram for the configuration connections pins. The ToolStick Base Adapter is available on the evaluation board. CPT007B Device Config Clk 1 k VDD Config Data GND ToolStick Figure 2.2. Configuration Connection Diagram CPT007B Data Sheet Typical Connection Diagrams

1. Electrical Specifications

3.1 Electrical Characteristics

All electrical parameters in all tables are specified under the conditions listed in Table 3.1 Recommended Operating Conditions on page 4, unless stated otherwise.

3.1.1 Recommended Operating Conditions

Table 3.1. Recommended Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Operating Supply Voltage on VDD VDD 1.8 2.4 3.6 V Minimum RAM Data Retention Voltage on VDD1 VRAM Not in Sleep Mode — 1.4 — V Sleep Mode — 0.3 0.5 V Operating Ambient Temperature TA –40 — 85 °C Note: 1. All voltages with respect to GND. CPT007B Data Sheet Electrical Specifications

3.1.2 Power Consumption

See 3.4 Typical Performance Curves for power consumption plots. Table 3.2. Power Consumption Parameter Symbol Test Condition Min Typ Max Unit Active Mode Supply Current IDD — 3.1 — mA Optimized Active Mode Supply Current IDD — 180 — µA Sleep Mode Current1, 2 IDD 3 sensors or fewer — 0.78 — µA 4 sensors — 0.79 — µA 5 sensors — 0.81 — µA 6 sensors — 0.82 — µA 7 sensors — 0.84 — µA System Current with Varying Scan Time — Base with One Sensor1 IDD Scan period = 10 ms — 154 — µA Scan period = 20 ms — 77 — µA Scan period = 50 ms — 31 — µA Scan period = 75 ms — 21 — µA Scan period = 100 ms — 16 — µA System Current with Varying Scan Time — Each Additional Sensor1 IDD Scan period = 10 ms — 47 — µA Scan period = 20 ms — 23 — µA Scan period = 50 ms — 9 — µA Scan period = 75 ms — 6 — µA Scan period = 100 ms — 5 — µA Note: 1. Measured with Free Run Mode disabled and sensors set to 4x accumulation, 8x gain. 2. Measured with scan period set to 250 ms. CPT007B Data Sheet Electrical Specifications

3.1.3 Reset and Supply Monitor

Table 3.3. Reset and Supply Monitor Parameter Symbol Test Condition Min Typ Max Unit VDD Supply Monitor Threshold VVDDM Reset Trigger 1.7 1.75 1.8 V VWARN Early Warning 1.8 1.85 1.9 V Power-On Reset (POR) Monitor Threshold VPOR Rising Voltage on VDD — 1.75 — V Falling Voltage on VDD 0.75 1.0 1.3 V VDD Ramp Time tRMP Time to VDD ≥ 1.8 V — — 3 ms RST Low Time to Generate Reset tRSTL 15 — — µs Boot Time1 tboot 1 sensor — 25 — ms 2 sensors — 40 — ms 3 sensors — 55 — ms 4 sensors — 70 — ms 5 sensors — 85 — ms 6 sensors — 100 — ms 7 sensors — 115 — ms Note: 1. Boot time is defined as the time from a power-on reset or /RST pin release until the first capacitive sense scan begins.

3.1.4 Configuration Memory

Table 3.4. Configuration Memory Parameter Symbol Test Condition Min Typ Max Units Endurance (Write/Erase Cycles) NWE 20 k 100 k — Cycles Note: 1. Data Retention Information is published in the Quarterly Quality and Reliability Report. CPT007B Data Sheet Electrical Specifications

3.1.5 Capacitive Sense

Table 3.5. Capacitive Sense Parameter Symbol Test Condition Min Typ Max Unit Scan Time Per Sensor1 tSCAN Accumulation = 1x — 64 — µs Accumulation = 4x — 256 — µs Accumulation = 8x — 512 — µs Accumulation = 16x — 1.024 — ms Accumulation = 32x — 2.048 — ms Accumulation = 64x — 4.096 — ms Signal to Noise Ratio1, 2 SNR Accumulation = 1x — 90:1 — codes Accumulation = 4x — 180:1 — codes Accumulation = 8x — 182:1 — codes Accumulation = 16x — 210:1 — codes Accumulation = 32x — 230:1 — codes Accumulation = 64x — 270:1 — codes Conversion Time tCONV Gain = 1x — 205 — µs Gain = 2x — 123 — µs Gain = 3x — 98 — µs Gain = 4x — 85 — µs Gain = 5x — 76 — µs Gain = 6x — 72 — µs Gain = 7x — 67 — µs Gain = 8x — 64 — µs Total Processing Time3 tPROC 1 sensor — 576 — µs 2 sensors — 796 — µs 3 sensors — 1.0 — ms 4 sensors — 1.2 — ms 5 sensors — 1.4 — ms 6 sensors — 1.7 — ms 7 sensors — 1.9 — ms Maximum External Capacitive Load CEXTMAX Gain = 8x — 45 — pF Gain = 1x — 500 — pF Maximum External Series Impe- dance REXTMAX Gain = 8x — 50 — kΩ CPT007B Data Sheet Electrical Specifications

Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Measured with gain set to 8x. 2. Measured with an evaluation board with 1/16" overlay using Capacitive Sense Profiler. 3. Sensors configured to 8x gain, 1x accumulation with sensor sampling and system processing time included and mutually-exclu- sive buttons, buzzer, and touch time-outs disabled.

3.1.6 General Purpose and Buzzer Outputs

Table 3.6. General Purpose and Buzzer Outputs Parameter Symbol Test Condition Min Typ Max Unit Output High Voltage (High Drive) VOH IOH = –3 mA VDD – 0.7 — — V Output Low Voltage (High Drive) VOL IOL = 8.5 mA — — 0.6 V Output High Voltage (Low Drive) VOH IOH = –1 mA VDD – 0.7 — — V Output Low Voltage (Low Drive) VOL IOL = 1.4 mA — — 0.6 V Weak Pull-Up Current IPU VDD = 1.8 V VIN = 0 V — –4 — µA VDD = 3.6 V VIN = 0 V –35 –20 — µA

3.2 Thermal Conditions

Table 3.7. Thermal Conditions Parameter Symbol Test Condition Min Typ Max Unit Thermal Resistance* θJA — 60 — °C/W Note: 1. Thermal resistance assumes a multi-layer PCB with any exposed pad soldered to a PCB pad. CPT007B Data Sheet Electrical Specifications

3.3 Absolute Maximum Ratings

Stresses above those listed in Table 3.8 Absolute Maximum Ratings on page 9 may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation list- ings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. For more information on the available quality and reliability data, see the Quality and Reliability Monitor Report at http://www.silabs.com/ support/quality/pages/default.aspx. Table 3.8. Absolute Maximum Ratings Parameter Symbol Test Condition Min Max Unit Ambient Temperature Under Bias TBIAS –55 125 °C Storage Temperature TSTG –65 150 °C Voltage on VDD VDD GND–0.3 4.0 V Voltage on I/O pins or RSTb VIN GND–0.3 VDD + 0.3 V Total Current Sunk into Supply Pin IVDD — 400 mA Total Current Sourced out of Ground Pin IGND 400 — mA Current Sourced or Sunk by Any I/O Pin or RSTb IIO –100 100 mA Maximum Total Current through all Port Pins IIOTOT — 200 mA Operating Junction Temperature TJ –40 105 °C Exposure to maximum rating conditions for extended periods may affect device reliability. CPT007B Data Sheet Electrical Specifications

3.4 Typical Performance Curves

Figure 3.1. Active Mode Processing Time Per Sensor Note: Active mode processing time per sensor measured with sensors configured to 1x accumulation, 8x gain. Sensor sampling and system processing time is included with mutually-exclusive buttons, the buzzer, and touch time-outs disabled. Figure 3.2. Current vs. Active Mode Scan Period — Base Current Consumption CPT007B Data Sheet Electrical Specifications

Figure 3.5. Typical VOL Curves CPT007B Data Sheet Electrical Specifications

1. Functional Description

4.1 Capacitive Sensing Input

4.1.1 Introduction

The capacitive to digital converter uses an iterative, charge-timing self-capacitance technique to measure capacitance on an input pin. Sampling is configured and controlled by settings in the non-volatile configuration profile, which can be changed through the 2-pin con- figuration interface. Baseline Active threshold Touch delta Inactive threshold Capacitance Time Figure 4.1. Capacitive Sense Data Types

4.1.2 Touch Qualification Criteria

The device detects a touch event when an inactive (untouched) input enabled by the input enable mask detects an sequence of meas- urements that cross the active threshold. The device detects a touch release event when an active (touched) input enabled by the input enable mask detects an sequence of measurements that cross the inactive threshold. The debounce configuration profile parameter defines how many measurements in a row must cross a threshold before a touch or re- lease is qualified. In electrically noisy environments more heavily filtered data is used for qualification.

4.1.3 Thresholds

Capacitive sensing inputs use input-specific thresholds for touch qualification. Each input uses two thresholds, one to detect inactive-to- active transitions on the input, and another to determine active-to-inactive transitions on the input. The inputs use two thresholds to add hysteresis and prevent active/inactive ringing on inputs. Each threshold can be set through Simplicity Studio tools and all thresholds are stored in non-volatile memory in the device's configuration profile. Thresholds are defined as percentages of a capacitive sensing input's touch delta. CPT007B Data Sheet Functional Description

4.1.4 Debounce Counter

Each capacitive sensing input maintains its own debounce counter. For an inactive sensor, this counter tracks the number of succes- sive samples which have crossed that input's active threshold. For an active sensor, this counter tracks the number of successive sam- ples which have crossed the inactive threshold. When the counter reaches a terminal value defined in the the configuration profile, the touch/release event is qualified.

4.1.5 Touch Deltas

Each capacitive sensing input uses a stored touch delta value that describes the expected difference between inactive and active ca- pacitive sensing output codes. This value is stored in the configuration profile for the system and is used by the touch qualification en- gine, which defines inactive and active thresholds relative to the touch delta. The touch deltas are stored in the configuration profile in a touch delta/16 format. For this reason, touch deltas must be configured as multiples of 16.

4.1.6 Auto-Accumulation and Averaging

Capacitive sensing inputs have an auto-accumulate and average post-sample filter that can be used to improve signal strength if nee- ded. Settings stored in the configuration profile can configure the engine to accumulate 1, 4, 8, 16, 32, or 64 samples. After the defined number of samples have been accumulated, the result is divided by either 1, 4, 8, 16, 32, or 64, depending on the accumulation setting. This auto-accumulated and averaged value is the sample output used for all touch qualification processing. Note that sample time per sensor increases as the level of accumulation increases. To reduce current consumption, the engine should not be set to auto-accumu- late unless it is required to achieve acceptable signal strength due to thick overlays or other system-level factors.

4.1.7 Drive strength

The drive strength of the current source used to charge the electrode being measured by the capacitive sensing input can be adjusted in integer increments from 1x to 8x (8x is the default). High drive strength gives the best sensitivity and resolution for small capacitors, such as those typically implemented as touch-sensitive PCB features. To measure larger capacitance values, the drive strength should be lowered accordingly. The highest drive strength setting that yields capacitive sensing output which does not saturate the sensing engine when the electrode is active (touched) should always be used to maximize input sensitivity.

4.1.8 Active Mode Scan Enable

Active mode scanning of capacitive sensing inputs is controlled by an enable setting for each capacitive sensing input. This setting is stored in the configuration profile.

4.1.9 Active Mode Scan Period

The capacitive sensing input engine stays in active mode whenever one or more inputs have qualified as active. During this time, the sensors scan at a periodicity defined by the active mode scan period, which is stored in the configuration profile. Every active mode scan pushes new samples through the processing engine, which checks for new touch and release events on all enabled inputs. If free run mode is enabled, the engine will repeatedly scan all enabled inputs during the active mode scan period. In this mode of operation, the active mode scan period is used as a timer to determine how much time has passed since the last qualified active sensor has been seen. When a defined amount of time without a qualified touch event has occurred, the engine switches to a low power mode using the sleep mode scan period, and conserves current. If free run mode is disabled, the engine will enter a low power state after completing one scan of all enabled inputs and processing the resulting samples. The engine will remain in this low power state until it wakes, at a time defined by active mode scan period, to perform another scan. CPT007B Data Sheet Functional Description

4.1.10 Active Mode Scan Type

The active mode scan type, which is stored in the configuration profile, controls whether the capacitive sensing engine in active mode will scan only once during the active mode scan period before going to sleep, or whether the engine will continue scanning as quickly as possible during the active mode scan period, never entering a low power state. For optimal responsiveness, the engine should be configured to run with free run mode enabled. Setting the scan mode to 'free run' causes touch qualification on a new touch to occur as quickly as the scanning engine can convert and process samples on all sensors. In this mode, qualification time is not bounded by active mode scan period, and is only bounded by scanning configuration factors such as the debounce setting, the number of enabled sensors, the accumulation setting on each sensor, and the timing constraints of any enabled component. For optimal current draw when in active mode, the engine should be configured to use the 'one scan per period' mode setting. In this case, touch qualification is bound by the scan period and the debounce setting of the device. Touch Event (t = 0 ms) 10 ms 20 ms 30 ms 40 ms Optimized Active sample sample Active process additional processing process additional processing Sleep sleep sleep debounce count = 1 touch qualified Figure 4.2. Timing and Current — One Sample Per Period Mode Touch Event (t = 0 ms) 10 ms 20 ms 30 ms 40 ms Optimized Active sample Active process additional processing Sleep debounce count = 1 touch qualifiedsample process additional processing Figure 4.3. Timing and Current — Free Run Mode

4.1.11 Sleep Mode Scan Period

The sleep mode scan period defines the rate at which a scan of the inputs enabled as wake-up sources are sampled. Each enabled sensor can also be enabled as a wake-up source. After the sleep mode scan completes, the scan is processed for a qualified candidate touch. If a candidate touch is qualified, the system wakes form sleep mode and enters active mode scanning. The sleep mode scan period is stored in the configuration profile and is defined in units of ms. CPT007B Data Sheet Functional Description

4.1.12 Active Mode and Sleep Mode Transitions

Capacitive sensing inputs will stay in active mode until no inputs detect qualified touches for a span of time defined by the counts until sleep parameter stored in the configuration profile. The scan period of enabled inputs is defined by the active mode scan period, also found in the configuration profile. If free run mode is enabled, the active mode sensing engine will remain awake and scanning the sen- sors as fast as possible. If free run mode is disabled, the engine will put itself into a low power state for the remainder of the active mode scan period, after a scan has completed. When in sleep mode, the sensing engine will wake at a period defined by sleep mode scan period to do a scan on sensors that have been enabled as wakeup sources. If the engine finds a candidate touch in this state, the system reverts to active mode to continue scanning. Note that in systems where a proximity input is selected, the sleep mode scan engine uses conversions on the proximity input instead of sensors enabled as wakeup sources. qualified touch release Touch Delta touch release new touch Device Execution no touch counter = 1 no touch counter = 2 ... no touch counter = counts before sleep device enters sleep sleep scan sees touch, wakes, qualifies touch no touch counter = 0 t Figure 4.4. Active and Sleep Transitions

4.2 Pin Output

4.2.1 Introduction

Results of the capacitive sensing touch qualification engine are communicated through a set of digital output pins. The state of each pin is bound to the touch qualification status of one capacitive sensing input pin. If a capacitive sensing input has qualified an active event, the corresponding output pin will be set to its active state. If the input has qualified a release event is inactive, the corresponding output pin will be set to its inactive state. Pin polarity and drive strength are configurable parameters. CPT007B Data Sheet Functional Description

4.2.2 Configuration

The configuration profile allows users to globally configure outputs as active high or active low. The configuration profile also allows users to globally configure pins as open drain outputs or push-pull outputs.

4.3 Capacitive Proximity Sensing

4.3.1 Wake on Proximity

The wake on capacitive proximity detection engine monitors for the presence of a conductive object such as a hand to move within detectable range of the sensor. When the engine detects an object, the device wakes from sleep and can begin qualifying touch events on all sensors enabled for active mode sensing.

4.3.2 Proximity Sensing Output

Proximity sensing state is output using a designated Out pin on the CPT007B. By choosing this pin, the user is effectively disabling the corresponding CS input pin. If the user is configuring proximity sensing to mode 2 operation, where a single capacitive sensing input pin is used for proximity detection, it is recommended that this input pin be the pin that corresponds to the selected proximity Out pin.

4.3.3 Proximity Configuration

The proximity sensing feature uses a single sensor input for proximity qualification. The configuration profile stores the pin chosen by the user. The sensor used for proximity qualification should also have a drive strength setting that is as high as possible without saturat- ing the input when no conductive object is in proximity to the proximity sensor. The accumulation setting of the input is also configura- ble. The proximity threshold controls the sensitivity of the input. A lower threshold setting increases sensitivity and increases the range of the sensor. A proximity sensing input cannot be used for touch qualification, and so the active and inactive thresholds are not used for proximity sensors. Additionally, the proximity input has no effect on other components of the device such as mutually exclusive button groups, buzzer output, touch time out timers, and sliders.

4.4 Touch Time-Out

The touch time-out feature can be enabled and disabled through the configuration profile. When enabled, the device will monitor touch event duration on each input independently. When a touch event exceeds a duration specified in the configuration profile, the device forces a release event, even if the user is still actively touching the sensor. The feature qualifies a touch release by adding the configured touch delta value for that sensor to the sensor's current baseline value. By doing this, the raw data-to-baseline delta created by the touch will be removed, and the touch qualification engine will see this as a touch release event. When the user removes a finger from a sensor that had been qualified active but has been qualified released through touch timeout, the resulting raw-to-baseline negative delta will be aggressively tracked downward by the baseline, resulting in a sensor that remains sensi- tive to successive touches. The touch timeout duration is configured globally, so all inputs are monitored for the same touch duration. If both the touch timeout feature and the mutually exclusive button group feature are enabled, the timeout timer will only run on the touch that is externally reported as being active.

4.5 Buzzer Output

4.5.1 Introduction

The buzzer output engine produces a square wave of a configurable duration and frequency when a capacitive sensing input goes from inactive to active. The feature can be enabled and disabled through the configuration profile. The configuration profile also includes the settings for active duration and frequency. CPT007B Data Sheet Functional Description

No Touch, Buzzer Inactive Device Execution Optimized Active sample sample Active process additional processing process additional processing Sleep sleep sleep Figure 4.5. Effects of the Buzzer on Current Draw — Active Mode, No Touch, Buzzer Inactive Touch Detected, Buzzer Active Device Execution Optimized Active Active additional processing Sleep sleep (stall)sample process additional processing sleep (stall)sample process Figure 4.6. Effects of the Buzzer on Current Draw — Active Mode, Touch Detected, Buzzer Active

4.5.2 Buzzer Configuration

If enabled, buzzer output will be routed to the Buzzer pin (pin 7) of the CPT007B. When activated, the buzzer will remain active for either the duration specified in the configuration profile, or until the last active sensor has qualified a touch release. The configuration profile supports configuration of output frequencies ranging from 1 kHz to 4 kHz. The configuration profile can configure the buzzer output pin to either push pull mode or open drain mode.

4.6 Mutually Exclusive Buttons

When enabled through the configuration profile, this system allows one and only one capacitive sensing input to be qualified as active at a time. The first sensor active will remain the only sensor active until released. The device will internally qualify multiple touch and release events but will not report them. CPT007B Data Sheet Functional Description

If multiple sensors have been internally qualified as active, the first sensor's touch event will be reported. If a touch event occurs simul- taneously on more than one sensor, the touch with the highest touch delta will be reported. If two sensors are qualified as active and the sensor being reported as active qualifies a touch release, the device will report that re- lease and then report a touch qualification on the still-active second sensor. In the case where a device has simultaneously qualified more than two active sensors and the reported active sensor qualifies and reports a release, the remaining qualified sensor with the highest sensor name will then be reported. For example, if sensors CS00, CS01, and CS02 are active with CS00 externally reported as active, after CS00's release, CS02 would be externally reported as an active sensor unless the device has already qualified a touch release on CS02. If both the touch timeout feature and the mutually exclusive button group feature are enabled, the timeout timer will only run on the touch that is externally reported as being active. CS00 Device Execution CS01 CS02 physical touch on pad touch reported by CPT device release reported by CPT device Figure 4.7. Mutually-Exclusive Button Operation

4.7 Self Testing

4.7.1 Introduction

When the self-test feature is enabled through the configuration profile, the device performs a check on all enabled capacitive sensing inputs upon startup to determine whether the sensing input pins are erroneously shorted to ground or supply. If a short or open is found on a sensor, the self test feature will signal that an error has been found through a port pin. The feature will then disable that sensor before beginning touch qualification scans on all sensors left enabled.

4.7.2 Test Failure Signaling

If the self test check reveals an error, the device will toggle the buzzer output pin at a frequency of 2 Hz. This toggling will persist for two seconds if the device detects one or more self test errors. CPT007B Data Sheet Functional Description

4.8 Configuration Profile

The configuration interface is used by the device to configure default values and performance characteristics that effect capacitive sensing. The configuration data can be programmed through the Configuration interface (Config Clk and Config Data pins) using [Con- figurator] in Simplicity Studio. Several configuration profile templates are available in Simplicity Studio to provide a starting point for development. CPT007B Data Sheet Functional Description

1. Pin Definitions 20 pin QFN (Top View) CS01 CS00 GND VDD RSTb / Config Clk Config Data CS06 OUT00 OUT01 OUT02 GND OUT03 CS02 CS03 CS04 CS05 GND 6 11 BUZZER OUT06 OUT05 OUT04 Figure 5.1. CPT007B Pinout Table 5.1. Pin Definitions for CPT007B-QFN20 Pin Number Pin Name Description

1 CS01 Analog input

2 CS00 Analog input

Capacitive sensing input 0

3 GND Ground

4 VDD Supply power input

5 RSTb /

6 Config Data Configuration data

7 Buzzer Push-pull output

8 OUT06 Push-pull output

9 OUT05 Push-pull output

10 OUT04 Push-pull output

11 OUT03 Push-pull output

12 GND Ground

13 OUT02 Push-pull output

14 OUT01 Push-pull output

15 OUT00 Push-pull output

16 CS06 Analog input

Capacitive sensing input 6

17 CS05 Analog input

Capacitive sensing input 5

18 CS04 Analog input

Capacitive sensing input 4

19 CS03 Analog input

Capacitive sensing input 3

20 CS02 Analog input

Capacitive sensing input 2 CPT007B Data Sheet Pin Definitions

1. QFN20 Package Specifications

6.1 QFN20 Package Dimensions

Figure 6.1. QFN20 Package Drawing Table 6.1. QFN20 Package Dimensions Dimension Min Typ Max A 0.50 0.55 0.60 A1 0.00 — 0.05 b 0.20 0.25 0.30 b1 0.275 0.325 0.375 D 3.00 BSC D2 1.6 1.70 1.80 e 0.50 BSC e1 0.513 BSC E 3.00 BSC E2 1.60 1.70 1.80 L 0.35 0.40 0.45 CPT007B Data Sheet

L1 0.00 — 0.10 aaa — 0.10 — bbb — 0.10 — ddd — 0.05 — eee — — 0.08 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing is based upon JEDEC Solid State Product Outline MO-248 but includes custom features which are toleranced per supplier designation. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. CPT007B Data Sheet

6.2 QFN20 PCB Land Pattern

Figure 6.2. QFN20 PCB Land Pattern Drawing Table 6.2. QFN20 PCB Land Pattern Dimensions Dimension Min Max C1 2.70 C2 2.70 C3 2.53 C4 2.53 E 0.50 REF X1 0.20 0.30 X2 0.24 .034 X3 1.70 1.80 Y1 0.50 0.60 Y2 0.24 0.34 Y3 1.70 1.80 CPT007B Data Sheet

Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. 3. This Land Pattern Design is based on the IPC-7351 guidelines. 4. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. 5. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 6. The stencil thickness should be 0.125 mm (5 mils). 7. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 8. A 2x2 array of 0.75 mm openings on a 0.95 mm pitch should be used for the center pad to assure proper paste volume. 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.

6.3 QFN20 Package Marking

Figure 6.3. QFN20 Package Marking The package marking consists of:

• 007B – The part number designation.
• TTTT – A trace or manufacturing code. The first letter of this code is the hardware revision.
• Y – The last digit of the assembly year.
• WW – The 2-digit workweek when the device was assembled.
• + – Indicates the device is RoHS-compliant. CPT007B Data Sheet

1. Relevant Application Notes The following Application Notes are applicable to the CPT007B devices:

• AN957: TouchXpress™ Configuration and Profiling Guide — This application note guides developers through the evaluation and configuration process of TouchXpress devices using Simplicity Studio [Xpress Configurator] and [Capacitive Sense Profiler].
• AN447: Printed Circuit Design Notes for Capacitive Sensing Performance — This document describes hardware design guidelines specifically for capacitive sensing applications, including button placement and other layout guidelines.
• AN949: TouchXpress™ Programming Guide — This application note discusses the production programming options available for TouchXpress devices. Application Notes can be accessed on the Silicon Labs website ( www.silabs.com/interface-appnotes) or in Simplicity Studio using the [Application Notes] tile. CPT007B Data Sheet Relevant Application Notes

Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory s izes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used w ithin any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applic ations. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energ y Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. http://www.silabs.com Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701 USA Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! IoT Portfolio www.silabs.com/IoT SW/HW www.silabs.com/simplicity Quality www.silabs.com/quality Support and Community community.silabs.com