T4WQ-F1F26 ELATEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
© 2023 – ELATEC GmbH – TWN4 Palon Square M LF HF data sheet – DocRev03 – EN – 11/2023 Page 1 of 4 TWN4 Palon Square M LF HF Multi- frequency RFID module (LF/HF) with NFC support TWN4 Palon Square M LF HF (exemplary illustration) The RFID modules of the TWN4 Palon Square M family are versatile reader/writer modules with a wide range of interfaces, like RS - 485 or Wiegand. All modules support NFC and, optionally, further interfaces like the OSDP protocol or I 2C. Although the modules are general-purpose devices, they are particularly appropriate for time attendance and access control applications. Thanks to their compact dimensions, they are the ideal solution for integration into third- party products. Key features of the TWN4 Palon Square M LF HF reader module include an optimized form factor for easy integration into any host device, the possibility to use many different interfaces, a tamper detection input and an on-board MEMS gyro sensor. Additionally, the module can read more than 60 RFID technologies from low (LF) and high frequency (HF) bands, including NFC. This gives the option to select as many of the technologies required instead of being forced to select just a few ones. Special features: + Possibility to read more than 60 RFID technologies + Supports many interfaces, like USB, RS-485, Wiegand and Clock/Data (OSDP protocol and I2C optionally) + Two RFID frequencies (125 kHz/13.56 MHz) and NFC support + Equipped with a tamper detection input and an on-board MEMS gyro sensor + Powerful SDK for writing apps which are executed directly on the module + Firmware update in the field possible + On-board 18 kB flash storage, e.g. for storing user accessible non-volatile data + Supports transparent data exchange with RFID media + CCID and PC/SC 2.01
© 2023 – ELATEC GmbH – TWN4 Palon Square M LF HF data sheet – DocRev03 – EN – 11/2023 Page 2 of 4 TECHNICAL DATA FREQUENCIES 125 kHz (LF) / 13.56 MHz (HF) ANTENNAS Integrated POWER Micro USB: 4.3 V – 5.5 V Connector X1: 9.0 V – 30 V PS2 classified power source according to IEC 62368-1, short-circuit current < 8 A CURRENT CONSUMPTION Operating: 180 mA @ 12 V typically / Idle: 50 mA @ 12 V typ. / Peak: 250 mA @ 12 V typ. TEMPERATURE RANGE Operating: -25 °C up to +80 °C (-13 °F up to +176 °F) Storage: -40 °C up to +85 °C (-40 °F up to +185 °F) RELATIVE HUMIDITY 5% to 95% non-condensing READ/WRITE DISTANCE LF and HF: up to 100 mm / 4 inch, depending on environment and transponder OPERATING MODES (USB) USB keyboard emulation – USB virtual COM port – CCID / PC/SC 2.01 MTBF 500,000 hours WEIGHT Approx. 25 g / 0.88 oz, depending on product derivate SABOTAGE DETECTION Tamper detection input On-board MEMS gyro sensor WIRE CONNECTOR Connector X1 1x10 pin header, RS-485 Connector X2 1x5 pin header for auxiliary ports/signals Connector X4 2x5 for I²C and extended ports SIGNALING 1 center RGB LED, on the rear side of the module (optional: up to 5 LEDs for OEM designs) Acoustic loudspeaker SUPPORTED OPTIONS AND TRANSPONDERS Depending on the firmware version and installed options, ELATEC readers and modules can support a wide range of RFID technologies. Please refer to the relevant ELATEC transponder matrix (available at www.elatec-rfid.com/int/transponder-technology) for more information about the available options and RFID technologies supported by the product. OS SUPPORT Windows 7 (32-/64-bit) and higher versions, Linux, Android1), iOS1), MAC OS X1) PERIPHERAL INTERFACES Micro USB, RS-485, OSDP1), I2C1), 2 SAM slots for ID-000 card format, 3 GPIOs, Wiegand D0/D1, Clock/Data, 1 tamper detection input TRANSMISSION SPEED USB full speed (12 Mbit/s), HF Air: up to 848 kbit/s, RS-485: up to 38,400 baud, I2C: 100 kbit/s RS-485 CONFIGURATION RS-485 address configuration and speed settings by upgrade card or AppBlaster tool or ex-fab preset. If required, RS-485 termination resistors to be provisioned off-board, externally. ENVIRONMENT Special TWN4 Palon Square M LF HF versions for potting or coating on request IMMUNITY AGAINST EM FIELDS 10 V/m according to EN 61000-6-2 CERTIFICATION NAME TWN4 Palon Square M LF HF CERTIFICATIONS Non-exhaustive list2): CE/RED, REACH and RoHS-III compliant ORDER CODES T4WQ-F1F26 Standard reader module T4WQ-F1F26-P Reader module with P option T4WQ-F1F26-PI Reader module with PI options Customer-specific TWN4 Palon Square M LF HF derivates and configurations are available on request. 1)On request 2)The product has been certified for use in many countries and regions. Contact your Sales representative for detailed information about all certifications and approvals granted to the product.
© 2023 – ELATEC GmbH – TWN4 Palon Square M LF HF data sheet – DocRev03 – EN – 11/2023 Page 3 of 4 ACCESSORIES CONNECTORS CON-0001 Spring contact with 2 cable guides, 10-pole CON-0002 Spring contact with 2 cable guides, 5-pole CON-0003 Pluggable connection clamp, 10-pole CON-0004 Pluggable connection clamp, 5-pole CABLES ELATEC RFID modules can be delivered with additional cables. Refer to the data sheet Cables for ELATEC devices for detailed information.
© 2023 – ELATEC GmbH – TWN4 Palon Square M LF HF data sheet – DocRev03 – EN – 11/2023 Page 4 of 4 TECHNICAL DRAWINGS ELATEC GmbH Zeppelinstr. 1
82178 Puchheim
E-Mail: info-rfid@elatec.com Website: elatec.com ELATEC Systems GmbH Schwieberdinger Str. 44
71636 Ludwigsburg
E-Mail: info-rfid@elatec.com Website: elatec.com ELATEC Inc.
1995 SW Martin Hwy
Palm City • FL 34990 USA P +1 772 210 2263 F +1 772 382 3749 E-Mail: americas-info@elatec.com Website: elatec.com ELATEC Technology (Shenzhen) LLC 918, Main Building, Tian An Cyber Times Tower, No. 6, Tairan Fourth Road, Tian 'an Community, Shatou Neighborhood Futian District • Shenzhen • China P/F +86 755 2394 6014 E-Mail: apac-info@elatec.com Website: elatec.com ELATEC reserves the right to change any information or data in this document without prior notice. ELATEC declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification. Disclaimer: All names used in this document are registered trademarks of their respective owners.