Power Management

S8333

Seiko Instruments Inc

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER

Manufacturer: Seiko Instruments Inc

Document: 44 Pages / 2Mb

Request Quote Download Datasheet Read online HTML view

More from Seiko Instruments Inc Browse S parts

Online Datasheet

Read S8333 online.

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 44

Technical content

www.sii-ic.com STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER © SII Semiconductor Corporation, 2004-2015 Rev.4.2_01 The S-8333 Series is a CMOS step-up switching regulator which ma inly consists of a reference voltage circuit, an oscillator, an error amplifier, a PWM controller, an under voltage lockout circuit (UVLO), and a timer latch short-circuit protection circuit. Because its minimum operating voltage is as low as 1.8 V, this switching regulator is ideal for the power supply of an LCD or for portable systems that operate on a low voltage. The internal oscillation frequency can be set up to 1.08 MHz, via the resistor connected to the ROSC pin. The maximum duty ratio of PWM control can be controlled by the resistor connected to the RDuty pin. The soft-start function at power application is accomplished by combini ng the reference voltage control and maximum duty control methods. Even if the voltage of the FB pin is retained lower than the reference voltage due to the factor outside the IC, the output voltage is raised by controlling the maximum duty. The phase compensation and gain value can be adjusted according to the values of the resistor and capacitor connec ted to the CC pin. Therefore, the operation stability and transient response can be correctly set for each application. The reference voltage accuracy is as high as 1.0 V ±1.5%, and any voltage can be output by using an external output voltage setting resistor. In addition, the delay time of the short-circuit protection circuit can be set by using the capacitor connected to the CSP pin. If the maximum duty condition continues because of short-circuiting, the capacitor externally connected to the CSP pin is charged, and oscillation stops after a specific time. The shor t-circuit protection function is cancelled when the power supply is raised to the UVLO release voltage after it has been lowere d to the UVLO detection voltage. A ceramic capacitor or a tantalum capacitor is used as the output ca pacitor, depending on the setting. This controller IC allows various settings and selections and employs a small package, making it very easy to use.  Features

Low voltage operation: 1.8 V to 6.0 V
Oscillation frequency: 280 kHz to 1.08 MHz (selectable by external resistor)
Maximum duty: Settable up to 88.5% by external resistor 47 to 88.5% (oscillation frequency; 500 kHz or more) 47 to 80% (oscillation frequency; less than 500 kHz)
Reference voltage: 1.0 V ±1.5%
Range of operation temperature: −40 to +85°C
UVLO (under-voltage lockout) function: Detection voltage can be selected from between 1.5 V and 2.3 V in 0.1 V step. Hysteresis width can be selected from be tween 0.1 V and 0.3 V in 0.1 V step.
Timer latch short-circuit protection circuit: Delay time can be set using an external capacitor.
Soft-start function: Soft-start time can be se lected in three steps, 10 ms, 15 ms, and 20 ms. Both reference voltage control and maximum duty control methods are applied
Phase compensation external setting: Control is possible via the resistor connected between the CC and GND pins and capacitor
Lead-free, Sn 100%, halogen-free *1. Refer to “ Product Name Structure ” for details.  Applications
Power supplies for LCDs and CCDs
Power supplies for portable equipment  Packages
SNT-8A
8-Pin TSSOP

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01  Block Diagram PWM comparator VOUT Timer latch short-circuit protection circuit RDuty RFB2 VSS RFB1 FB SD L VIN EXT UVLO CSP CC RZ CZ ROSC CFB Oscillator Maximum duty soft-start circuit Reference voltage (1.0 V) soft-start circuit Error amplifier CIN CL Figure 1 Block Diagram

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Product Name Structure 1. Product name (1) SNT-8A S-8333 C x x x - I 8 T 1 U Package abbreviation and packing specifications*1 I8T1: SNT-8A , tape product Soft-start time setting A: 10 ms B: 15 ms C: 20 ms UVLO setting A: 2.3 V B: 2.2 V C: 2.1 V D: 2.0 V E: 1.9 V F: 1.8 V G: 1.7 V H: 1.6 V I: 1.5 V UVLO hysteresis setting A: 0.1 V B: 0.2 V C: 0.3 V Environmental code U: Lead-free (Sn 100%), halogen-free *1. Refer to the tape drawing.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 (2) 8-Pin TSSOP S-8333 C x x x - T8T1 x Package abbreviation and packing specifications*1 T8T1: 8-Pin TSSOP, tape product Environmental code U: Lead-free (Sn 100%), halogen-free S: Lead-free, halogen-free Soft-start time setting A: 10 ms B: 15 ms C: 20 ms UVLO setting A: 2.3 V B: 2.2 V C: 2.1 V D: 2.0 V E: 1.9 V F: 1.8 V G: 1.7 V H: 1.6 V I: 1.5 V UVLO hysteresis setting A: 0.1 V B: 0.2 V C: 0.3 V *1. Refer to the tape drawing. 2. Packages Package Name Drawing Code Package Tape Reel Land SNT-8A PH008-A-P-SD PH008-A-C- SD PH008-A-R-SD PH008-A-L-SD 8-Pin TSSOP FT008-A-P-SD FT008-E-C-SD FT008-E-R-SD ⎯

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Pin Configurations 1. SNT-8A Table 1 Top view Figure 2 Pin No. Symbol Description

1 CC Error amplifier circuit output phase

2 FB Output voltage feedback pin

3 CSP Short-circuit protecti on delay time setting pin

4 VIN Power supply input pin

5 EXT External transistor connection pin

6 VSS GND pin

7 ROSC Oscillation frequency setting resistor

8 RDuty Maximum duty setting resistor connection pin

8-Pin TSSOP Table 2 Top view Figure 3 Pin No. Symbol Description

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01  Absolute Maximum Ratings Table 3 Absolute Maximum Ratings (Unless otherwise specified: Ta = 25°C, VSS = 0 V) Parameter Symbol Ratings Unit VIN pin voltage V IN V SS − 0.3 to VSS + 6.5 V FB pin voltage V FB V SS − 0.3 to VSS + 6.5 V EXT pin voltage V EXT V SS − 0.3 to VIN + 0.3 V CSP pin voltage V CSP V SS − 0.3 to VIN + 0.3 V CC pin voltage V CC V SS − 0.3 to VIN + 0.3 V CC pin current I CC ±10 mA ROSC pin voltage V ROSC V SS − 0.3 to VIN + 0.3 V ROSC pin current I ROSC ±10 mA RDuty pin voltage V RDuty V SS − 0.3 to VIN + 0.3 V RDuty pin current I RDuty ±10 mA Power dissipation SNT-8A PD 450*1 mW 8-Pin TSSOP 300 (When not mounted on board) mW 700*1 mW Operating ambient temperature T opr −40 to +85 °C Storage temperature T stg −40 to +125 °C *1. When mounted on board [Mounted board] (1) Board size: 114.3 mm × 76.2 mm × t1.6 mm (2) Name: JEDEC STANDARD51-7 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. 0 50 100 1500 Ambient temperature (Ta) [°C] 600 400 200 8-Pin TSSOP 800 Power dissipation (PD) [mW] SNT-8A Figure 4 Power Dissipation of Package (When mounted on board)

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Electrical Characteristics Table 4 Electrical Characteristics (Unless otherwise specified: V IN = 3.3 V, Ta = 25°C) Parameter Symbol Conditions Min. Typ. Max. Unit Test Circuit Operating input voltage V IN ⎯ 1.8 ⎯ 6.0 V 2 FB voltage V FB ⎯ 0.985 1.000 1.015 V 2 Current consumption I SS1 fosc = 650 kHz VFB = 0.95 V ⎯ 450 700 μA 1 EXT pin output current IEXTH V EXT = VIN − 0.4 V ⎯ −100 −60 mA 1 IEXTL V EXT = 0.4 V 100 160 ⎯ mA 1 FB voltage temperature coefficient ΔVFB ΔTa Ta = −40 to +85°C ⎯ ±100 ⎯ ppm/ °C2 FB pin input current I FB ⎯ −0.1 ⎯ +0.1 μA 1 Oscillation frequency *1 fosc When fosc = 1080 kHz is set (ROSC = 120 kΩ) When fosc = 650 kHz is set (ROSC = 200 kΩ) When fosc = 280 kHz is set (ROSC = 470 kΩ) VFB = 0.9 V Waveform on EXT pin is measured. fosc × 0.9 fosc fosc × 1.1 kHz 1 Oscillation frequency temperature coefficient Δfosc ΔTa Ta = −40 to +85°C fosc = 650 kHz ⎯ 1000 ⎯ ppm/ °C1 Max. duty*2 MaxDuty fosc = 1080 kHz (R OSC = 120 kΩ) MaxDuty = 88.5% (RDuty = 62 kΩ) MaxDuty = 73% (RDuty = 180 kΩ) MaxDuty = 47% (RDuty = 390 kΩ) MaxDuty − 5 MaxDuty MaxDuty + 5 % 1 fosc = 650 kHz (R OSC = 200 kΩ) MaxDuty = 88.5% (RDuty = 100 kΩ) Soft-start time t SS tSS = 10 ms, 15 ms, 20 ms Selected in three steps tSS × 0.75 tSS tSS × 1.5 ms 1 Short-circuit protection delay time*3 tPRO tPRO = 50 ms (CSP = 0.1 μF) 37.5 50 75 ms 1 UVLO detection voltage V UVLO VUVLO = 1.5 V to 2.3 V Selected in 0.1 V steps VUVLO × 0.95 VUVLO VUVLO × 1.05 V 1 UVLO hysteresis width V UVLOHYS VUVLOHYS = 0.1 V to 0.3 V Selected in 0.1 V steps VUVLOHYS × 0.6 VUVLOHYS VUVLOHYS × 1.4 V 1 CC pin output current ICCH V FB = 2 V −60 −45 −34.5 μA 1 ICCL V FB = 0 V 34.5 45 60 μA 1 Timer latch reset voltage VRTLT1 Within short-circuit protection delay time 0.7 1.0 1.3 V 1 VRTLT2 After short-circuit protection circuit operated VUVLO × 0.95 VUVLO VUVLO × 1.05 V 1 *1. The recommended range of the resistance (R osc) for oscillation frequency is R osc = 120 kΩ to 470 k Ω (fOSC = 280 kHz to 1.08 MHz). This range of oscillation frequency is the typical value when an i deal resistor is connected externally. In actual use, it is n ecessary to take account the dispersion of an IC ( ±10%) into this value. Between 47 and 80 % (R Duty/ROSC = 1.0 to 3.2); the oscillation frequency is less than 500 kHz This range of max. duty is the typical value when an ideal resistor is connected externally. In actu al use, it is necessary to take account the dispersion of an IC ( ±5%) into this value. *3. The short-circuit protection time can be set by the external capacitor. Although the maximum set value by the external capacit or is unlimited under the ideal condition, set C SP = approx. 0.47 μF as a target maximum value due to discharge time of the capacitor.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01  External Parts When Measuring Electrical Characteristics Table 5 External Parts Element Name Symbol Manufacturer Part Number Inductor L TDK Corporation LDR655312T 10 μH Diode SD Rohm Co., Ltd. RB491D Output capacitor CL ⎯ Ceramic 10 μF Transistor M1 Sanyo Electric Co., Ltd. MCH3406 Oscillation frequency setting resistor ROSC ⎯ 200 k Ω (when fOSC = 650 kHz) Maximum duty ratio setting resistor RDuty ⎯ 300 k Ω (when MaxDuty = 73%) Short-circuit protection delay time setting ca pacitor CSP ⎯ 0.1 μF (when tPRO = 50 ms) Output voltage setting resistor 1 RFB1 ⎯ 8.2 k Ω (when VOUT = 9.2 V) Output voltage setting resistor 2 RFB2 ⎯ 1.0 k Ω (when VOUT = 9.2 V) FB pin capacitor CFB ⎯ 180 pF Phase compensation resistor RZ ⎯ 200 k Ω Phase compensation capacitor CZ ⎯ 0.01 μF

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01  Operation 1. Switching control method 1. 1 PWM control The S-8333 Series is a DC-DC converter using a pulse width modulation method (PWM). The pulse width of the S-8333 Series varies from 0% to the maximum duty set by RDuty depending on the load current, but its switching frequency does not change. C onsequently, the ripple voltage generated from switching can be removed easily via a filter. 2. Soft-start function For this IC, the built- in soft-start circuit controls the rush current and overshoot of the output voltage when powering on. Reference voltage adjustment and maximum duty control methods are adopted as the soft-start methods. The following describes the so ft-start function at power application. In the circuit where the input voltage is not directly out put at shutdown by inserting a switch (SW) between the diode (SD) and V OUT output, the V OUT voltage when the V IN voltage is applied with the SW OFF stays 0 V. Therefore, the voltage of the FB pin stays 0 V and the EX T output is in the step up status between the “H” and “L” levels due to the maximum duty. The maximum duty at th is time is approximately 7% and the rush current at power application is controlled. The maximum duty soft start is accomplished by gradually increasing the duty width up to the maximum du ty set by the external re sistor RDuty (refer to Figure 8). The reference voltage of the error amplifier input also gradually increases from 0 V at the same time as the maximum duty soft start. The increasing of the output volt age is controlled by turning the SW ON. The soft-start function is realized by controlling the voltage of the FB pin so that it is the same potential as the reference voltage that is slowly raised. A Rail-to-Rail amplifier is adopted as the error amplifier, whic h means that the voltage is loop controlled so that it can be th e same as the reference voltage. Once the reference voltage rises, the voltage cannot be reset (the reference voltage is 0 V) unless making the power supply voltage lower than the UVLO detection voltage. Conversely, when the power supply voltage rises up to the reset voltage after it is lowered to the UVLO dete ction voltage or lower, the output voltage is stepped up by the soft-start function. PWM Comparator VOUT RFB2 RFB1 FB SD L VIN EXT CC RZ CZ − CL Error amplifier Vref 0.5 V 0 V Error amplifier reference voltage SW Figure 7

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series (VIN = 0 V→3.3 V, VOUT = 9.2 V, RFB1 = 8.2 kΩ, RFB2 = 1.0 kΩ) 0 V Input voltage (VIN) 3.3 V 0 V Output voltage (VOU T) SW : ON 0 V Error amplifier reference voltage 1.0 V 0 V FB pin voltage (VFB) 1.0 V 0 V EXT pin volt age (VEX T) 3.3 V t (ms) VOUT×0.95 Maximum duty soft-start period 9.2 V Reference voltage soft-start period tSS Figure 8

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 3. Timer latch short-circuit protection function This IC has a timer latch short-circuit protection circuit that stops the switching operation when the output voltage drops for a specific time due to output short-circuiting. A ca pacitor (CSP) that is used to set the delay time of this short-circuit protection circuit can be connected to the CSP pin. This IC operates at the maximum duty ratio if the outp ut voltage drops due to output short-circuiting. At the maximum duty ratio, constant-current charging of CSP starts. If this status lasts for a short-circuit protection delay time and the CSP pin voltage rises above the reference voltage, the latch mode is set. Note that the latch mode is different from the shutdown status in that the switching operation is stopped but the internal circuitry operates normally. To reset the latch operation to protect the IC from short-circuiting, lower V IN than the UVLO detection voltage. The latch mode within the short-circuit protection delay time is reset by decreasing V IN to 1.0 V (Typ.) or lower. Note that the mode is not reset even if the V IN is lowered to the UVLO detection voltage (refer to Figure 9). Input voltage (VIN) Output load CSP pin voltage (VCSP) Latch mode Short-circuit status 50 ms (CSP = 0.1 μF) Normal status Short-circuit protection time Latch period Reset period Reset period Short-circuit protection time Short-circuit protection time UVLO release UVLO detection 1.0 V Reference voltage Figure 9 4. UVLO function This IC includes a UVLO (under-voltage lockout) circuit to prevent the IC from malfunctioning due to a transient status when power is applied or a momentary drop of the power supply voltage. When UVLO is in the detection state, switching is stopped and the external FET is held in the off status. Once UVLO enters the detection state, the soft-start function is reset. Note that the other internal circuits operate normally and that the status is different from the power-off status.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 5. Error amplifier The error amplifier outputs the PWM control signal so that the voltage of the FB pin is held at a specific value (1 V). By connecting a resistor (RZ) and capacitor (CZ) to the output pin (CC pin) of the error amplifier in series, an optional loop gain can be set, enabling stabilized phase compensation. 6. Operation The following are basic equations [(1) through (7)] of the step-up switching regulator (refer to Figure 10). DL CL M1 FB CONT VIN EXT VSS VOUT Figure 10 Step-up Switching Regulator Circuit for Basic Equations Voltage at the CONT pin at the moment M1 is turned ON (current I L flowing through L is zero), V A: *1. V S: Non-saturated voltage of M1 Change in I L over time: L VV L V dt Integration of the above equation: tL VVI SIN L × IL flows while M1 is ON (t on). This time is determined by the oscillation frequency of OSC. Peak current (I PK) after tON: ON SIN PK tL VVI × The energy stored in L is represented by 1 × L (IPK)2. When M1 is turned OFF (t OFF), the energy stored in L is released via a diode, generating a reverse voltage (V L). VL: ( ) IN *2. V D: Diode forward voltage The voltage on the CONT pin rises only by V OUT + VD.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 Change in current (I L) flowing through the diode into V OUT during tOFF: L VVV L V dt Integration of the above equation is as follows: tL VVVII INDOUT PKL × During tON, energy is stored in L and is not transmitted to V OUT. When receiving output current (I OUT) from VOUT, the energy of the capacitor (C L) is used. As a result, the pin voltage of CL is reduced, and goes to the lowest level after M1 is turned ON (tON). When M1 is turned OFF, the energy stored in L is transmitted via the diode to CL, and the pin voltage of C L rises drastically. Because V OUT is a time function indicating the maximum value (ripple voltage: V p-p) when the current flowing through the diode into V OUT and the load current I OUT match. Next, this ripple voltage is determined as follows. IOUT vs t1 (time) from after t ON, when VOUT reaches the maximum level: INDOUT PKOUT tL VVVII × ()  −+×−=∴ INDOUT OUTPK VVV When tOFF, IL = 0 (when the energy of the inductor is completely transmitted): Based on equation (7), PK OFF INDOUT I t VVV L = When substituting equation (10) for equation (9): OFF PK OUT OFF t I Itt1 ×−=  Electrical charge ΔQ1 which is charged in C L during t1: INDOUT 1PK 1INDOUT1 PK L1 t2 L VVVtItdt L VVVdt IdtI Q ttt When substituting equation (12) for equation (9): () 1 OUTPK 1OUTPKPK1 t 2 A rise voltage (V p-p) due to ΔQ1: 1P - P t2 II C C ∆QV OUTPK LL ×+×==  When taking into consideration I OUT consumed during t 1 and ESR*1 (RESR) of CL: L 1OUT ESR OUTPK OUTPK LL PP C t IR2 IIt2 II C C  + +× *1. Equivalent Series Resistance When substituting equation (11) for equation (15): ESR OUTPK L OFF PK OUTPK PP R 2 II C t I 2 )I(IV × Therefore to reduce the ripple voltage, it is important that the capacitor connected to the output pin has a large capacity and a small ESR.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  External Parts Selection 1. Inductor The inductance has a strong influence on the maximum output current (I OUT) and efficiency ( η). The peak current (I PK) increases by decreasing L and the st ability of the circuit improves and I OUT increases. If L is decreased further, the efficiency falls, and I OUT decreases if the current drive capability of the external transistor is insufficient. The loss of I PK by the switching transistor decreases by increasing L and the efficiency becomes maximum at a certain L value. Further increasing L decrease the efficiency due to the loss of the DC resistance of the inductor. IOUT also decreases. If the oscillation frequency is higher, a smaller L value can be chosen, making the inductor smaller. In the S-8333 Series, the oscillation frequency can be varied within the range of 280 kHz to 1.08 MHz by the external resistor, so select an L value best suited to the frequency. The recommended value is between 2.2 μH and 22 μH. When selecting an inductor, note the allowable current of the inductor. If a current exceeding this allowable current flows through the inductor, magnetic saturation occurs, substantially lowering the efficiency and increasing the current, which results in damage to the IC. Therefore, select an inductor so that I PK does not exceed the allowable current. I PK is expressed by the following equations in the discontinuous mode and continuous mode. Lf )VV(VI 2I osc INDOUTOUT PK Lf)V(V2 V)VV(VIV VVI oscDOUT ININDOUT OUT IN DOUT PK ××+× fOSC = Oscillation frequency, V D ≅ 0.4 V. 2. Diode Use an external diode that meets the following requirements.

Low forward voltage
High switching speed
Reverse breakdown voltage: V OUT + [Spike voltage] or more
Rated current: I PK or more 3. Capacitors (C IN, CL) The capacitor on the input side (C IN) can lower the supply impedance and level the input current for better efficiency. Select C IN according to the impedance of the power supply to be used. The capacitor on the output side (C L) is used to smooth the output voltage. Select an appropriate capacitance value based on the I/O conditions and load conditions. A capacitance of 10 μF or more is recommended. By adjusting the phase compensation of the feedback loop using the external resistor (RZ) and capacitor (CZ), a ceramic capacitor can be used as the capacitor on the output side. If a capacitor whose equivalent series resistance is between 30 m Ω and 500 m Ω is used as the output capacitor, the adjustable range of the phase compensation is wider; however, note that other characteristics may be affected by ripple voltage or other conditions at this time. The optimal capacitor differs depending on the L value, capacitance value, wiring, and application (output load), so select the capacitor after performing sufficient evaluation under the actual usage conditions.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 4. External transistor A bipolar (NPN) or enhancement (N-channel) MOS FET transistor can be used as the external capacitor. 4. 1 Bipolar (NPN) type The driving capability when the output current is increased by using a bipolar transistor is determined by h FE and Rb of the bipolar transistor. Figure 11 shows a peripheral circuit. Nch Pch Rb VIN IPK EXT Cb 2200 pF 1 kΩ Figure 11 External Transistor Periphery 1 kΩ is recommended for R b. Actually, calculate the necessary base current (I b) from hFE of the bipolar transistor as follows and select an R b value lower than this. Ib = hFE IPK Rb = Ib VIN − 0.7 IEXTH 0.4 A small Rb increases the output current, but the efficiency decreases. Actually, a pulsating current flows and a voltage drop occurs due to the wiring capacitance. Determine the optimum value by experiment. A speed-up capacitor (C b) connected in parallel with R b resistance as shown in Figure 11 decreases the switching loss and improves the efficiency. Select Cb by observing the following equation. Cb ≤ 1 2 π × Rb × fosc × 0.7 However, in practice, the optimum C b value also varies depending on the characteristics of the bipolar transistor employed. Therefore, determine the optimum value of C b by experiment. 4. 2 Enhancement MOS FET type Use an Nch power MOS FET. For high efficiency, using a MOS FET with a low ON resistance (R ON) and small input capacitance (C ISS) is ideal, however, ON resistance and input capacitance generally share a trade-off relationship. The ON resistance is efficient in a range in which the output current is relatively great during low-frequency switching, and t he input capacitance is efficient in a range in which the output current is middling during high-frequency switching. Select a MOS FET whose ON resistance and input capacitance are optimal depending on the usage conditions. The input voltage (V IN) is supplied for the gate voltage of the MOS FET, so select a MOS FET with a gate withstanding voltage that is equal to the maximum usage value of the input voltage or higher and a drain withstanding voltage that is equal to the amount of the output voltage (V OUT) and diode voltage (V D) or higher. If a MOS FET with a threshold that is near the UVLO detection voltage is used, a large current may flow, stopping the output voltage from rising and possibly generating heat in the worst case. Select a MOS FET with a threshold that is sufficiently lower than the UVLO detection voltage value.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 6. Short-circuit protection delay time setting capacitor (CSP) With the S-8333 Series, the short-circuit protection delay time can be set to any value by an external capacitor. Connect the capacitor across the CSP and VSS pins. Select the capacitance by using the following equation and referring to Figure 14. However, the following equation and figure assume that the capacitor value is the desired value and show the theoretical values when the IC is in the typical conditions. Note that fluctuations of capacitor and IC are not considered. CSP [μF] ≅ 1.0 tPRO [ms] × 2 × 10−3 120 100 0 0.10 0.20 0.25 tPRO [ms] CSP [μF] 0.05 0.15 Figure 14 C SP vs. tPRO 7. Output voltage setting resistors (RFB1, RBF2) With the S-8333 Series, the output voltage can be set to any value by external divider resistors. Connect the divider resistors across the V OUT and VSS pins. Because V FB = 1 V, the output voltage can be calculated by this equation. = VOUT RFB2 (RFB1 + RFB2) Connect divider resistors RFB1 and RFB2 as close to the IC to minimize effects from of noise. If noise does have an effect, adjust the values of RFB1 and RFB2 so that R FB1 + RFB2 < 100 kΩ. CFB connected in parallel with RFB1 is a capacitor for phase compensation. Select the optimum value of this capacitor at which the stable operation can be ensured from the values of the inductor and output capacitor. 8. Phase compensation setting resistor and capacitor (RZ, CZ) The S-8333 Series needs appropriate compensation for the voltage feedback loop to prevent excessive output ripple and unstable operation from deteriorating the efficiency. This compensation is implemented by connecting RZ and CZ in series across the CC and VSS pins. RZ sets the high-frequency gain for a high-speed transient response. CZ sets the pole and zero of the error amplifier and keeps the loop stable. Adjust RZ and CZ, taking into consideration conditions such as the inductor, output capacitor, and load current, so that the optimum transient characteristics can be obtained.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Standard Circuit PWM comparator VOUT Timer latch short-circuit protection circuit RDuty RFB2 VSS RFB1 FB SD L VIN EXT UVLO CSP CC RZ CZ ROSC CFB CIN Oscillator Maximum duty soft-start circuit Reference voltage (1.0 V) soft-start circuit Error amplifier 0.1 μF ROSC RDuty CL Ground point Figure 15 Standard Circuit Caution The above connection diagram and constant will not guarantee successful operation. Perform thorough evaluation using the actual application to set the constant.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01  Precaution

Mount external capacitors, diodes, and inductor as close as possible to the IC.
Characteristics ripple voltage and spike noise occur in IC containing switching regulators. Moreover rush current flows at the time of a power supply injection. Because these largely depend on the inductor, the capacitor and impedance of power supply used, fully check them using an actually mounted model.
Make sure the dissipation of the switching transistor (especially at a high temperature) does not exceed the allowable power dissipation of the package.
The performance of a switching regulator varies depending on the design of the PCB patterns, peripheral circuits, and external parts. Thoroughly test all settings with your device.
The capacitor, diode, inductor and others used as external parts do not assure the operation at high temperature. Evaluate fully using the actual application when designing.
This IC builds in soft start function, starts reference voltage gradually, and it is controlled so that FB pin voltage and reference voltage become this potential. Therefore, keep in mind that it will be in a maximum duty state according to the factor of IC exterior if FB pin voltage is held less than reference voltage.
Although the IC contains a static electricity protection circui t, static electricity or voltage that exceeds the limit of the protection circuit should not be applied.
SII Semiconductor Corporation assumes no responsibility for the way in which this IC is used on products created using this IC or for the specifications of that product, nor does SII Semiconductor Corporation assume any responsibility for any infringement of patents or copyrights by products that include this IC either in Japan or in other countries.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Characteristics (Typical Data) 1. Example of Major Temperature Characteristics (Ta = −40 to +85°C) ISS1 vs. Ta (VIN = 3.3 V) /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K38/K30/K30 /K37/K30/K30 /K36/K30/K30 /K35/K30/K30 /K34/K30/K30 /K33/K30/K30 /K32/K30/K30 /K31/K30/K30 /K30 /K49 /K53/K53/K31 /K5B /K6D /K41/K5D /K54/K61 /K5B /KB0 /K43/K5D /K66 /K4F/K53/K43 /K3D /K31/K30/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K31/K32/K30 /K6B /K57 /K29 /K2D /K32/K30 /K31/K30/K30 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K32/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K34/K37/K30 /K6B /K57 /K29 IEXTH vs. Ta (V IN = 3.3 V) I EXTL vs. Ta (VIN = 3.3 V) /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K2D /K32/K30/K30 /K2D /K31/K38/K30 /K2D /K31/K36/K30 /K2D /K31/K34/K30 /K2D /K31/K32/K30 /K2D /K31/K30/K30 /K2D /K38/K30 /K2D /K36/K30 /K2D /K34/K30 /K2D /K32/K30 /K30 /K49 /K45/K58/K54/K48 /K5B/K6D/K41/K5D /K54/K61 /K5B /KB0 /K43/K5D /K2D /K32/K30 /K31/K30/K30 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A/K2C /K4D/K61/K78/K44/K75/K74/K79/K3D /K37/K33/K25 /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57/K2C /K52 /K44/K75/K74/K79 /K3D /K33/K30/K30 /K6B /K57 /K29 /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K32/K30/K30 /K31/K38/K30 /K31/K36/K30 /K31/K34/K30 /K31/K32/K30 /K31/K30/K30 /K38/K30 /K36/K30 /K34/K30 /K32/K30 /K30 /K49 /K45/K58/K54/K4C /K5B/K6D/K41/K5D /K54/K61 /K5B /KB0 /K43/K5D /K2D /K32/K30 /K31/K30/K30 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A/K2C /K4D/K61/K78/K44/K75/K74/K79 /K3D /K37/K33/K25 /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57/K2C /K52 /K44/K75/K74/K79 /K3D /K33/K30/K30 /K6B /K57 /K29 IFB vs. Ta (V IN = 3.3 V) fOSC vs. Ta (V IN = 3.3 V) 40 0 20 40 60 80 0.10 0.08 0.06 0.04 0.02 0.02 0.04 0.06 0.08 0.10 IFB [A] Ta [C] 20 100 /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K31/K34/K30/K30 /K31/K32/K30/K30 /K31/K30/K30/K30 /K38/K30/K30 /K36/K30/K30 /K34/K30/K30 /K32/K30/K30 /K30 /K66 /K4F/K53/K43 /K5B/K6B/K48/K7A/K5D /K54/K61 /K5B /KB0 /K43/K5D /K2D /K32/K30 /K31/K30/K30 /K66 /K4F/K53/K43 /K3D /K31/K30/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K31/K32/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K32/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K34/K37/K30 /K6B /K57 /K29 MaxDuty vs. Ta (V IN = 3.3 V) tSS vs. Ta (VIN = 3.3 V) 40 0 20 40 60 80 100 MaxDuty [%] Ta [C] 20 100 MaxDuty = 88.5% (ROSC = 200 kRDuty = 100 k) MaxDuty = 73% (ROSC = 200 kRDuty = 300 k) MaxDuty = 47% (ROSC = 200 kRDuty = 640 k) 4 0 0 2 04 06 08 0 25.0 20.0 15.0 10.0 5.0 tSS [ms] Ta [C] 20 100 tSS = 20 ms tSS = 10 ms

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 tPRO vs. Ta (V IN = 3.3 V) VUVLO vs. Ta 40 0 20 40 60 80 70.0 60.0 50.0 40.0 30.0 20.0 10.0 tPRO [ms] Ta [C] 20 100 tPRO = 50 ms (CSP = 0.1 F) 40 0 20 40 60 80 2.5 2.0 1.5 1.0 0.5 VUVLO [V] Ta [C] 20 100 VUVLO = 2.3 V VUVLO = 1.5 V VUVLOHYS vs. Ta ICCH vs. Ta (V IN = 3.3 V) 40 0 20 40 60 80 0.35 0.30 0.25 0.20 0.15 0.10 0.05 VUVLOHYS [V] Ta [C] 20 100 VUVLOHYS = 0.3 V VUVLOHYS = 0.1 V /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K2D /K31/K30/K30 /K2D /K39/K30 /K2D /K38/K30 /K2D /K37/K30 /K2D /K36/K30 /K2D /K35/K30 /K2D /K34/K30 /K2D /K33/K30 /K2D /K32/K30 /K2D /K31/K30 /K30 /K49 /K43/K43/K48 /K5B /K6D /K41/K5D /K54/K61 /K5B /KB0 /K43/K5D /K2D /K32/K30 /K31/K30/K30 ICCL vs. Ta (V IN = 3.3 V) VRTLT1 vs. Ta (VIN = 3.3 V) /K2D /K34/K30 /K30 /K32/K30 /K34/K30 /K36/K30 /K38/K30 /K31/K30/K30 /K39/K30 /K38/K30 /K37/K30 /K36/K30 /K35/K30 /K34/K30 /K33/K30 /K32/K30 /K31/K30 /K30 /K49 /K43/K43/K4C /K5B /K6D /K41/K5D /K54/K61 /K5B /KB0 /K43/K5D /K2D /K32/K30 /K31/K30/K30 40 0 20 40 60 80 1.2 1.0 0.8 0.6 0.4 0.2 VRTLT1 [V] Ta [C] 20 100

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 2. Example of Major Power Supply Dependence Characteristics (Ta = 25°C) ISS1 vs. VIN /K30/K32 /K33 /K34 /K35 /K36 /K31/K34/K30/K30 /K31/K32/K30/K30 /K31/K30/K30/K30 /K38/K30/K30 /K36/K30/K30 /K34/K30/K30 /K32/K30/K30 /K30 /K49 /K53/K53/K31 /K5B /K6D /K41/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37 /K66 /K4F/K53/K43 /K3D /K31/K30/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K31/K32/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K32/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K34/K37/K30 /K6B /K57 /K29 IEXTH vs. VIN I EXTL vs. VIN /K30/K32 /K33 /K34 /K35 /K36 /K2D /K32/K30/K30 /K2D /K31/K38/K30 /K2D /K31/K36/K30 /K2D /K31/K34/K30 /K2D /K31/K32/K30 /K2D /K31/K30/K30 /K2D /K38/K30 /K2D /K36/K30 /K2D /K34/K30 /K2D /K32/K30 /K30 /K49 /K45/K58/K54/K48 /K5B/K6D/K41/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A/K2C /K4D/K61/K78/K44/K75/K74/K79 /K3D /K37/K33/K25 /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57/K2C /K52 /K44/K75/K74/K79 /K3D /K33/K30/K30 /K6B /K57 /K29 /K30/K32 /K33 /K34 /K35 /K36 /K32/K30/K30 /K31/K38/K30 /K31/K36/K30 /K31/K34/K30 /K31/K32/K30 /K31/K30/K30 /K38/K30 /K36/K30 /K34/K30 /K32/K30 /K30 /K49 /K45/K58/K54/K4C /K5B/K6D/K41/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A/K2C /K4D/K61/K78/K44/K75/K74/K79 /K3D /K37/K33/K25 /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57/K2C /K52 /K44/K75/K74/K79 /K3D /K33/K30/K30 /K6B /K57 /K29 IFB vs. VIN fOSC vs. VIN 02 3 4 5 6 0.10 0.08 0.06 0.04 0.02 0.02 0.04 0.06 0.08 0.10 IFB [A] VIN [V] 1 7 /K30/K32 /K33 /K34 /K35 /K36 /K31/K34/K30/K30 /K31/K32/K30/K30 /K31/K30/K30/K30 /K38/K30/K30 /K36/K30/K30 /K34/K30/K30 /K32/K30/K30 /K30 /K66 /K4F/K53/K43 /K5B/K6B/K48/K7A/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37 /K66 /K4F/K53/K43 /K3D /K31/K30/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K31/K32/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K36/K35/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K32/K30/K30 /K6B /K57 /K29 /K66 /K4F/K53/K43 /K3D /K32/K38/K30 /K6B/K48/K7A /K28/K52 /K4F/K53/K43 /K3D /K34/K37/K30 /K6B /K57 /K29 MaxDuty vs. V IN tSS vs. VIN 02 3 4 5 6 100 MaxDuty [%] VIN [V] 1 7 MaxDuty = 88.5% (ROSC = 200 kRDuty = 100 k) MaxDuty = 73% (ROSC = 200 kRDuty = 300 k) MaxDuty = 47% (ROSC = 200 kRDuty = 640 k) 02 3 4 5 6 25.0 20.0 15.0 10.0 5.0 tSS [ms] VIN [V] 1 7 tSS = 20 ms tSS = 10 ms

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 tPRO vs. VIN ICCH vs. VIN 02 3 4 5 6 70.0 60.0 50.0 40.0 30.0 20.0 10.0 tPRO [ms] VIN [V] 1 7 tPRO=50 ms (CSP = 0.1 F) /K30/K32 /K33 /K34 /K35 /K36 /K2D /K31/K30/K30 /K2D /K39/K30 /K2D /K38/K30 /K2D /K37/K30 /K2D /K36/K30 /K2D /K35/K30 /K2D /K34/K30 /K2D /K33/K30 /K2D /K32/K30 /K2D /K31/K30 /K30 /K49 /K43/K43/K48 /K5B /K6D /K41/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37 ICCL vs. VIN /K30/K32 /K33 /K34 /K35 /K36 /K31/K30/K30 /K39/K30 /K38/K30 /K37/K30 /K36/K30 /K35/K30 /K34/K30 /K33/K30 /K32/K30 /K31/K30 /K30 /K49 /K43/K43/K4C /K5B /K6D /K41/K5D /K56 /K49/K4E /K5B/K56/K5D /K31 /K37

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 3. Example of External Parts Dependence Characteristics fOSC vs. ROSC (VIN = 3.3 V) /K30 /K32/K30/K30 /K33/K30/K30 /K34/K30/K30 /K35/K30/K30 /K36/K30/K30 /K31/K36/K30/K30 /K31/K34/K30/K30 /K31/K32/K30/K30 /K31/K30/K30/K30 /K38/K30/K30 /K36/K30/K30 /K34/K30/K30 /K32/K30/K30 /K30 /K66 /K4F/K53/K43 /K5B/K6B/K48/K7A/K5D /K52 /K4F/K53/K43 /K5B/K6B /K57 /K5D /K31/K30/K30 /K54/K61 /K3D /K2D /K34/K30 /KB0 /K43 /K54 /K61/K3D/K32 /K35 /KB0 /K43 /K54 /K61/K3D/K38 /K35 /KB0 /K43 MaxDuty vs. R Duty / ROSC (ROSC = 200 kΩ, VIN = 3.3 V) 0 1 1.5 2 2.5 3 100 MaxDuty [%] RDuty / ROSC 0.5 3.5 4.5 4 Ta = 40C Ta = 25C Ta = 85C tPRO vs. CSP (V IN = 3.3 V) 0 0.2 0.3 0.4 0.5 350 300 250 200 150 100 tPRO [ms] CSP [F] 0.1 Ta = 40C Ta = 25C Ta = 85C

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 4. Examples of Transient Response Characteristics 4.1 Powering ON (V OUT = 9.2 V, VIN = 0 V → 3.3 V, Ta = 25°C) Remark The switch (SW) is inserted between the diode (SD) and VOUT output. Controlled externally to turn SW on a few ms later after the VIN voltage is applied. (1) f OSC = 1080 kHz, I OUT = 0 mA, tSS = 10 ms (2) f OSC = 1080 kHz, I OUT = 100 mA, tSS = 10 ms 5 5 10 15 20 VIN [V] time [ms] VOUT [V] 5 5 10 15 20 VIN [V] time [ms] VOUT [V] (3) fOSC = 650 kHz, I OUT = 0 mA, tSS = 10 ms (4) f OSC = 650 kHz, I OUT = 100 mA, tSS = 10 ms 5 5 10 15 20 VIN [V] time [ms] VOUT [V] 5 5 10 15 20 VIN [V] time [ms] VOUT [V] (5) fOSC = 280 kHz, I OUT = 0 mA, tSS = 10 ms (6) fOSC = 280 kHz, I OUT = 100 mA, tSS = 10 ms 5 5 10 15 20 VIN [V] time [ms] VOUT [V] 5 5 10 15 20 VIN [V] time [ms] VOUT [V]

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 4.2 Load fluctuations (V OUT = 9.2 V, VIN = 3.3 V, Ta = 25°C, RZ = 200 kΩ, CZ = 0.01 μF) (1) fOSC = 1080 kHz, I OUT = 0.1 mA→100 mA (2) f OSC = 1080 kHz, I OUT = 100 mA→0.1 mA 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8 (3) fOSC = 650 kHz, I OUT = 0.1 mA→100 mA (4) f OSC = 650 kHz, I OUT = 100 mA→0.1 mA 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8 (5) fOSC = 280 kHz, I OUT = 0.1 mA→100 mA (6) f OSC = 280 kHz, I OUT = 100 mA→0.1 mA 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8 20 0 10 20 time [ms] 10 IOUT 100 mA 0.1 mA VOUT [0.2 V/div] 10.0 9.8 9.6 9.4 9.2 9.0 8.8

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 4.3 Input voltage fluctuations (V OUT = 9.2 V, IOUT = 100 mA, RZ = 200 kΩ, CZ = 0.01 μF) (1) fOSC = 1080 kHz, V IN = 2.8 V→3.8 V (2) f OSC = 1080 kHz, V IN = 3.8 V→2.8 V 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10 (3) fOSC = 650 kHz, V IN = 2.8 V→3.8 V (4) f OSC = 650 kHz, V IN = 3.8 V→2.8 V 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10 (5) fOSC = 280 kHz, V IN = 2.8 V→3.8 V (6) f OSC = 280 kHz, V IN = 3.8 V→2.8 V 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10 20 0 10 20 time [ms] 10 VIN [V] 4.0 3.5 3.0 2.5 V OUT [V] 9.40 9.30 9.20 9.10

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Reference Data 1. Reference data for external parts Table 6 Properties of External Parts Element Name Product Name Manufacture Characteristics Inductor LDR655312T TDK Corporation 10 μH, DCR*1 = 307 mΩ, IMAX*2 = 0.7 A, Height = 1.2 mm Diode RB491D Rohm Co., Ltd. VF*3 = 0.45 V, I F*4 = 1.0 A Output capacitor (ceramic) ⎯ ⎯ 16 V, 10 μF Transistor MCH3406 Sanyo Electric Co., Ltd. VDSS*5 = 20 V, VGSS*6 = ±10 V, Ciss*7 = 280 pF, RDS(ON)*8 = 82 mΩ max. (VGS*9 = 2.5 V, ID*10 = 1 A) *1. DCR : DC resistance *2. IMAX : Maximum allowable current *3. VF : Forward voltage *4. IF : Forward current *5. VDSS : Drain to source voltage (when short circuited between the gate and source) *6. VGSS : Gate to source voltage (when short circuited between the drain and source) *7. Ciss : Input capacitance *8. RDS(ON) : Drain to source on resistance *9. VGS : Gate to source voltage *10. ID : Drain current Caution The values shown in the characteristics column of Table 6 above are based on the materials provided by each manufacturer. However, consider the characteristics of the original materials when using the above products.

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 2. Reference data (1) The data of (a) output current (I OUT) vs. efficiency ( η) characteristics and (b) output current (I OUT) vs. output voltage (VOUT) characteristics is shown below. 2. 1 VOUT = 13.1 V (RFB1 = 7.5 kΩ, RFB2 = 620 Ω) (1) fOSC = 1080 kHz, MaxDuty = 73% (ROSC = 120 kΩ, RDuty = 180 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V 0.01 1 10 100 1000 13.20 13.15 13.10 13.05 13.00 12.95

12.90 VOUT [V]

IOUT [mA] 0.1 VIN = 5.0 V (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V 0.01 1 10 100 1000 13.20 13.15 13.10 13.05 13.00 12.95 IOUT [mA] 0.1 VIN = 5.0 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V 0.01 1 10 100 1000 13.20 13.15 13.10 13.05 13.00 12.95 IOUT [mA] 0.1 VIN = 5.0 V

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 2. 2 VOUT = 9.2 V (RFB1 = 8.2 kΩ, RFB2 = 1.0 kΩ) (1) fOSC = 1080 kHz, MaxDuty = 73% (ROSC = 120 kΩ, RDuty = 180 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V 0.01 1 10 100 1000 9.30 9.25 9.20 9.15 9.10 9.05 9.00 VOUT [V] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V 0.01 1 10 100 1000 9.30 9.25 9.20 9.15 9.10 9.05 9.00 VOUT [V] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V 0.01 1 10 100 1000 9.30 9.25 9.20 9.15 9.10 9.05 9.00 VOUT [V] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 2. 3 VOUT = 6.1 V (RFB1 = 5.1 kΩ, RFB2 = 1.0 kΩ) (1) fOSC = 1080 kHz, MaxDuty = 73% (ROSC = 120 kΩ, RDuty = 180 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V 0.01 1 10 100 1000 6.20 6.15 6.10 6.05 6.00 5.95 5.90 VOUT [V] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V 0.01 1 10 100 1000 6.20 6.15 6.10 6.05 6.00 5.95 5.90 VOUT [V] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) (a) IOUT vs. η (b) I OUT vs. VOUT 0.01 1 10 100 1000 100  [%] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V 0.01 1 10 100 1000 6.20 6.15 6.10 6.05 6.00 5.95 5.90 VOUT [V] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series 3. Reference data (2) The data of output current (I OUT) vs. ripple voltage (Vr) characteristics is shown below. 3. 1 VOUT = 13.1 V (RFB1 = 7.5 kΩ, RFB2 = 620 Ω) (1) fOSC = 1080 kHz, MaxDuty = 73 % (ROSC = 120 kΩ, RDuty = 180 kΩ) (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V 3. 2 VOUT = 9.2 V (RFB1 = 8.2 kΩ, RFB2 = 1.0 kΩ) (1) fOSC = 1080 kHz, MaxDuty = 73% (ROSC = 120 kΩ, RDuty = 180 kΩ) (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 5.0 V VIN = 3.3 V

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 3. 3 VOUT = 6.1 V (RFB1 = 5.1 kΩ, RFB2 = 1.0 kΩ) (1) fOSC = 1080 kHz, MaxDuty = 73% (ROSC = 120 kΩ, RDuty = 180 kΩ) (2) fOSC = 650 kHz, MaxDuty = 73% (ROSC = 200 kΩ, RDuty = 300 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V (3) fOSC = 280 kHz, MaxDuty = 73% (ROSC = 470 kΩ, RDuty = 750 kΩ) 0.01 1 10 100 1000 100 Vr [mV] IOUT [mA] 0.1 VIN = 3.3 V VIN = 2.5 V

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER Rev.4.2_01 S-8333 Series  Marking Specifications 1. SNT-8A Top view 14 32 85 67 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (1): Blank (2) to (4): Product code (Refer to Product name vs. Product code ) (5), (6): Blank (7) to (11): Lot number Product name vs. Product code Product name Product code Product name Product code S-8333CAAA-I8T1U U 2 A S-8333CBEC-I8T1U U 3 O S-8333CAAB-I8T1U U 2 B S-8333CBFA-I8T1U U 3 P S-8333CAAC-I8T1U U 2 C S-8333CBFB-I8T1U U 3 Q S-8333CABA-I8T1U U 2 D S-8333CBFC-I8T1U U 3 R S-8333CABB-I8T1U U 2 E S-8333CBGA-I8T1U U 3 S S-8333CABC-I8T1U U 2 F S-8333CBGB-I8T1U U 3 T S-8333CACA-I8T1U U 2 G S-8333CBGC-I8T1U U 3 U S-8333CACB-I8T1U U 2 H S-8333CBHA-I8T1U U 3 V S-8333CACC-I8T1U U 2 I S-8333CBHB-I8T1U U 3 W S-8333CADA-I8T1U U 2 J S-8333CBHC-I8T1U U 3 X S-8333CADB-I8T1U U 2 K S-8333CBIA-I8T1U U 3 Y S-8333CADC-I8T1U U 2 L S-8333CBIB-I8T1U U 3 Z S-8333CAEA-I8T1U U 2 M S-8333CBIC-I8T1U U 3 3 S-8333CAEB-I8T1U U 2 N S-8333CCAA-I8T1U U 4 A S-8333CAEC-I8T1U U 2 O S-8333CCAB-I8T1U U 4 B S-8333CAFA-I8T1U U 2 P S-8333CCAC-I8T1U U 4 C S-8333CAFB-I8T1U U 2 Q S-8333CCBA-I8T1U U 4 D S-8333CAFC-I8T1U U 2 R S-8333CCBB-I8T1U U 4 E S-8333CAGA-I8T1U U 2 S S-8333CCBC-I8T1U U 4 F S-8333CAGB-I8T1U U 2 T S-8333CCCA-I8T1U U 4 G S-8333CAGC-I8T1U U 2 U S-8333CCCB-I8T1U U 4 H S-8333CAHA-I8T1U U 2 V S-8333CCCC-I8T1U U 4 I S-8333CAHB-I8T1U U 2 W S-8333CCDA-I8T1U U 4 J S-8333CAHC-I8T1U U 2 X S-8333CCDB-I8T1U U 4 K S-8333CAIA-I8T1U U 2 Y S-8333CCDC-I8T1U U 4 L S-8333CAIB-I8T1U U 2 Z S-8333CCEA-I8T1U U 4 M S-8333CAIC-I8T1U U 2 3 S-8333CCEB-I8T1U U 4 N S-8333CBAA-I8T1U U 3 A S-8333CCEC-I8T1U U 4 O S-8333CBAB-I8T1U U 3 B S-8333CCFA-I8T1U U 4 P S-8333CBAC-I8T1U U 3 C S-8333CCFB-I8T1U U 4 Q S-8333CBBA-I8T1U U 3 D S-8333CCFC-I8T1U U 4 R S-8333CBBB-I8T1U U 3 E S-8333CCGA-I8T1U U 4 S S-8333CBBC-I8T1U U 3 F S-8333CCGB-I8T1U U 4 T S-8333CBCA-I8T1U U 3 G S-8333CCGC-I8T1U U 4 U S-8333CBCB-I8T1U U 3 H S-8333CCHA-I8T1U U 4 V S-8333CBCC-I8T1U U 3 I S-8333CCHB-I8T1U U 4 W S-8333CBDA-I8T1U U 3 J S-8333CCHC-I8T1U U 4 X S-8333CBDB-I8T1U U 3 K S-8333CCIA-I8T1U U 4 Y S-8333CBDC-I8T1U U 3 L S-8333CCIB-I8T1U U 4 Z S-8333CBEA-I8T1U U 3 M S-8333CCIC-I8T1U U 4 3 S-8333CBEB-I8T1U U 3 N

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER S-8333 Series Rev.4.2_01 2. 8-Pin TSSOP Top view (1) (2) (3) (4) (5) (6) (7) (8) (1) to (4): Product name: 8333 (Fixed) (5) to (8): Function code (Refer to Product name vs. Function code) (9) to (14): Lot number Product name vs. Function code Product name Function code Product name Function code S-8333CAAA-T8T1y C A A A S-8333CBEC-T8T1y C B E C S-8333CAAB-T8T1y C A A B S-8333CBFA-T8T1y C B F A S-8333CAAC-T8T1y C A A C S-8333CBFB-T8T1y C B F B S-8333CABA-T8T1y C A B A S-8333CBFC-T8T1y C B F C S-8333CABB-T8T1y C A B B S-8333CBGA-T8T1y C B G A S-8333CABC-T8T1y C A B C S-8333CBGB-T8T1y C B G B S-8333CACA-T8T1y C A C A S-8333CBGC-T8T1y C B G C S-8333CACB-T8T1y C A C B S-8333CBHA-T8T1y C B H A S-8333CACC-T8T1y C A C C S-8333CBHB-T8T1y C B H B S-8333CADA-T8T1y C A D A S-8333CBHC-T8T1y C B H C S-8333CADB-T8T1y C A D B S-8333CBIA-T8T1y C B I A S-8333CADC-T8T1y C A D C S-8333CBIB-T8T1y C B I B S-8333CAEA-T8T1y C A E A S-8333CBIC-T8T1y C B I C S-8333CAEB-T8T1y C A E B S-8333CCAA-T8T1y C C A A S-8333CAEC-T8T1y C A E C S-8333CCAB-T8T1y C C A B S-8333CAFA-T8T1y C A F A S-8333CCAC-T8T1y C C A C S-8333CAFB-T8T1y C A F B S-8333CCBA-T8T1y C C B A S-8333CAFC-T8T1y C A F C S-8333CCBB-T8T1y C C B B S-8333CAGA-T8T1y C A G A S-8333CCBC-T8T1y C C B C S-8333CAGB-T8T1y C A G B S-8333CCCA-T8T1y C C C A S-8333CAGC-T8T1y C A G C S-8333CCCB-T8T1y C C C B S-8333CAHA-T8T1y C A H A S-8333CCCC-T8T1y C C C C S-8333CAHB-T8T1y C A H B S-8333CCDA-T8T1y C C D A S-8333CAHC-T8T1y C A H C S-8333CCDB-T8T1y C C D B S-8333CAIA-T8T1y C A I A S-8333CCDC-T8T1y C C D C S-8333CAIB-T8T1y C A I B S-8333CCEA-T8T1y C C E A S-8333CAIC-T8T1y C A I C S-8333CCEB-T8T1y C C E B S-8333CBAA-T8T1y C B A A S-8333CCEC-T8T1y C C E C S-8333CBAB-T8T1y C B A B S-8333CCFA-T8T1y C C F A S-8333CBAC-T8T1y C B A C S-8333CCFB-T8T1y C C F B S-8333CBBA-T8T1y C B B A S-8333CCFC-T8T1y C C F C S-8333CBBB-T8T1y C B B B S-8333CCGA-T8T1y C C G A S-8333CBBC-T8T1y C B B C S-8333CCGB-T8T1y C C G B S-8333CBCA-T8T1y C B C A S-8333CCGC-T8T1y C C G C S-8333CBCB-T8T1y C B C B S-8333CCHA-T8T1y C C H A S-8333CBCC-T8T1y C B C C S-8333CCHB-T8T1y C C H B S-8333CBDA-T8T1y C B D A S-8333CCHC-T8T1y C C H C S-8333CBDB-T8T1y C B D B S-8333CCIA-T8T1y C C I A S-8333CBDC-T8T1y C B D C S-8333CCIB-T8T1y C C I B S-8333CBEA-T8T1y C B E A S-8333CCIC-T8T1y C C I C S-8333CBEB-T8T1y C B E B Remark 1. y: S or U 2. Please select products of environmental code = U for Sn 100%, halogen-free products.

/X53/X49/X49/X20/X53/X65/X6D/X69/X63/X6F/X6E/X64/X75/X63/X74/X6F/X72/X20/X43/X6F/X72/X70/X6F/X72/X61/X74/X69/X6F/X6E /X4E/X6F/X2E /X54/X49/X54/X4C/X45 /X53/X43/X41/X4C/X45 /X55/X4E/X49/X54/X6D/X6D /X53/X4E/X54/X2D/X38/X41/X2D/X41 /X20/X20/X20/X20/X20/X20/X2D/X4C/X61/X6E/X64/X20/X52/X65/X63/X6F/X6D/X6D/X65/X6E/X64/X61/X74/X69/X6F/X6E /X50/X48/X30/X30/X38/X2D/X41/X2D/X4C/X2D/X53/X44/X2D/X34/X2E/X31 /X30/X2E/X33/X30/X2E/X32 /X30/X2E/X35/X32 /X32/X2E/X30/X31 /X30/X2E/X35/X32 /X4E/X6F/X2E/X20/X50/X48/X30/X30/X38/X2D/X41/X2D/X4C/X2D/X53/X44/X2D/X34/X2E/X31 /X43/X61/X75/X74/X69/X6F/X6E /X31/X2E/X20/X44/X6F/X20/X6E/X6F/X74/X20/X64/X6F/X20/X73/X69/X6C/X6B/X73/X63/X72/X65/X65/X6E/X20/X70/X72/X69/X6E/X74/X69/X6E/X67/X20/X61/X6E/X64/X20/X73/X6F/X6C/X64/X65/X72/X20/X70/X72/X69/X6E/X74/X69/X6E/X67/X20/X75/X6E/X64/X65/X72/X20/X74/X68/X65/X20/X6D/X6F/X6C/X64/X20/X72/X65/X73/X69/X6E/X20/X6F/X66/X20/X74/X68/X65/X20/X70/X61/X63/X6B/X61/X67/X65/X2E /X32/X2E/X20/X54/X68/X65/X20/X74/X68/X69/X63/X6B/X6E/X65/X73/X73/X20/X6F/X66/X20/X74/X68/X65/X20/X73/X6F/X6C/X64/X65/X72/X20/X72/X65/X73/X69/X73/X74/X20/X6F/X6E/X20/X74/X68/X65/X20/X77/X69/X72/X65/X20/X70/X61/X74/X74/X65/X72/X6E/X20/X75/X6E/X64/X65/X72/X20/X74/X68/X65/X20/X70/X61/X63/X6B/X61/X67/X65/X20/X73/X68/X6F/X75/X6C/X64/X20/X62/X65/X20/X30/X2E/X30/X33/X20/X6D/X6D /X20/X6F/X72/X20/X6C/X65/X73/X73/X20/X66/X72/X6F/X6D/X20/X74/X68/X65/X20/X6C/X61/X6E/X64/X20/X70/X61/X74/X74/X65/X72/X6E/X20/X73/X75/X72/X66/X61/X63/X65/X2E /X33/X2E/X20/X4D/X61/X74/X63/X68/X20/X74/X68/X65/X20/X6D/X61/X73/X6B/X20/X61/X70/X65/X72/X74/X75/X72/X65/X20/X73/X69/X7A/X65/X20/X61/X6E/X64/X20/X61/X70/X65/X72/X74/X75/X72/X65/X20/X70/X6F/X73/X69/X74/X69/X6F/X6E/X20/X77/X69/X74/X68/X20/X74/X68/X65/X20/X6C/X61/X6E/X64/X20/X70/X61/X74/X74/X65/X72/X6E/X2E /X34/X2E/X20/X52/X65/X66/X65/X72/X20/X74/X6F/X20/X22/X53/X4E/X54/X20/X50/X61/X63/X6B/X61/X67/X65/X20/X55/X73/X65/X72/X27/X73/X20/X47/X75/X69/X64/X65/X22/X20/X66/X6F/X72/X20/X64/X65/X74/X61/X69/X6C/X73/X2E /X31/X2E/X20 /X28/X30/X2E/X32/X35/X20/X6D/X6D/X20/X6D/X69/X6E/X2E/X20/X2F/X20/X30/X2E/X33/X30/X20/X6D/X6D/X20/X74/X79/X70/X2E/X29 /X32/X2E/X20 /X20/X28/X31/X2E/X39/X36/X20/X6D/X6D/X20/X7E/X20/X32/X2E/X30/X36/X20/X6D/X6D/X29 /X31/X2E /X32/X2E /X30/X2E/X30/X33/X20/X6D/X6D /X33/X2E /X34/X2E /X53/X4E/X54 /X31/X2E/X20/X50/X61/X79/X20/X61/X74/X74/X65/X6E/X74/X69/X6F/X6E/X20/X74/X6F/X20/X74/X68/X65/X20/X6C/X61/X6E/X64/X20/X70/X61/X74/X74/X65/X72/X6E/X20/X77/X69/X64/X74/X68/X20/X28/X30/X2E/X32/X35/X20/X6D/X6D/X20/X6D/X69/X6E/X2E/X20/X2F/X20/X30/X2E/X33/X30/X20/X6D/X6D/X20/X74/X79/X70/X2E/X29/X2E /X32/X2E/X20/X44/X6F/X20/X6E/X6F/X74/X20/X77/X69/X64/X65/X6E/X20/X74/X68/X65/X20/X6C/X61/X6E/X64/X20/X70/X61/X74/X74/X65/X72/X6E/X20/X74/X6F/X20/X74/X68/X65/X20/X63/X65/X6E/X74/X65/X72/X20/X6F/X66/X20/X74/X68/X65/X20/X70/X61/X63/X6B/X61/X67/X65/X20/X28/X31/X2E/X39/X36/X20/X6D/X6D/X20/X74/X6F/X20/X32/X2E/X30/X36/X6D/X6D/X29/X2E /X31 /X32 /X31/X2E /X32/X2E/X20 /X28/X31/X2E/X39/X36/X20/X6D/X6D/X20/X7E/X20/X32/X2E/X30/X36/X20/X6D/X6D/X29 /X28/X30/X2E/X32/X35/X20/X6D/X6D/X20/X6D/X69/X6E/X2E/X20/X2F/X20/X30/X2E/X33/X30/X20/X6D/X6D/X20/X74/X79/X70/X2E/X29

/X4E/X6F/X2E /X54/X49/X54/X4C/X45 /X53/X43/X41/X4C/X45 /X55/X4E/X49/X54 /X53/X49/X49/X20/X53/X65/X6D/X69/X63/X6F/X6E/X64/X75/X63/X74/X6F/X72/X20/X43/X6F/X72/X70/X6F/X72/X61/X74/X69/X6F/X6E /X54/X53/X53/X4F/X50/X38/X2D/X45/X2D/X50/X4B/X47/X20/X44/X69/X6D/X65/X6E/X73/X69/X6F/X6E/X73 /X4E/X6F/X2E/X20/X46/X54/X30/X30/X38/X2D/X41/X2D/X50/X2D/X53/X44/X2D/X31/X2E/X31 /X46/X54/X30/X30/X38/X2D/X41/X2D/X50/X2D/X53/X44/X2D/X31/X2E/X31 /X30/X2E/X31/X37/XB1/X30/X2E/X30/X35 /X33/X2E/X30/X30/X2B/X30/X2E/X33 /X20/X2D/X30/X2E/X32 /X30/X2E/X36/X35 /X30/X2E/X32/XB1/X30/X2E/X31 /X31 /X34 /X35/X38 /X6D/X6D

/X4E/X6F/X2E /X54/X49/X54/X4C/X45 /X53/X43/X41/X4C/X45 /X55/X4E/X49/X54 /X53/X49/X49/X20/X53/X65/X6D/X69/X63/X6F/X6E/X64/X75/X63/X74/X6F/X72/X20/X43/X6F/X72/X70/X6F/X72/X61/X74/X69/X6F/X6E /XF8/X31/X2E/X35/X35/XB1/X30/X2E/X30/X35 /X32/X2E/X30/XB1/X30/X2E/X30/X35 /X38/X2E/X30/XB1/X30/X2E/X31/XF8/X31/X2E/X35/X35/X2B/X30/X2E/X31 /X20/X2D/X30/X2E/X30/X35 /X28/X34/X2E/X34/X29 /X30/X2E/X33/XB1/X30/X2E/X30/X35 /X31 /X34 /X35 /X38 /X34/X2E/X30/XB1/X30/X2E/X31 /X46/X65/X65/X64/X20/X64/X69/X72/X65/X63/X74/X69/X6F/X6E /X54/X53/X53/X4F/X50/X38/X2D/X45/X2D/X43/X61/X72/X72/X69/X65/X72/X20/X54/X61/X70/X65 /X4E/X6F/X2E/X20/X46/X54/X30/X30/X38/X2D/X45/X2D/X43/X2D/X53/X44/X2D/X31/X2E/X30 /X46/X54/X30/X30/X38/X2D/X45/X2D/X43/X2D/X53/X44/X2D/X31/X2E/X30 /X2B/X30/X2E/X34 /X20/X2D/X30/X2E/X32/X36/X2E/X36 /X6D/X6D

/X4E/X6F/X2E /X54/X49/X54/X4C/X45 /X53/X43/X41/X4C/X45 /X55/X4E/X49/X54 /X53/X49/X49/X20/X53/X65/X6D/X69/X63/X6F/X6E/X64/X75/X63/X74/X6F/X72/X20/X43/X6F/X72/X70/X6F/X72/X61/X74/X69/X6F/X6E /X45/X6E/X6C/X61/X72/X67/X65/X64/X20/X64/X72/X61/X77/X69/X6E/X67/X20/X69/X6E/X20/X74/X68/X65/X20/X63/X65/X6E/X74/X72/X61/X6C/X20/X70/X61/X72/X74 /X4E/X6F/X2E/X20/X46/X54/X30/X30/X38/X2D/X45/X2D/X52/X2D/X53/X44/X2D/X31/X2E/X30 /X32/XB1/X30/X2E/X35 /XF8/X31/X33/XB1/X30/X2E/X35 /XF8/X32/X31/XB1/X30/X2E/X38 /X31/X33/X2E/X34/XB1/X31/X2E/X30 /X31/X37/X2E/X35/XB1/X31/X2E/X30 /X33/X2C/X30/X30/X30/X51/X54/X59/X2E /X54/X53/X53/X4F/X50/X38/X2D/X45/X2D/X52/X65/X65/X6C /X46/X54/X30/X30/X38/X2D/X45/X2D/X52/X2D/X53/X44/X2D/X31/X2E/X30 /X6D/X6D

Disclaimers (Handling Precautions) 1. All the information described herei n (product data, specifications, figur es, tables, programs, algorithms and application circuit examples, etc.) is cu rrent as of publishing dat e of this document and is subject to change without notice. 2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of any specific mass-production design. SII Semiconductor Corporation is not responsible for damages caused by the reasons other than the products or infringement of third-party intellectual property rights and any other rights due to the use of the information described herein. 3. SII Semiconductor Corporation is not responsible for da mages caused by the incorrect information described herein. 4. Take care to use the products described herein within their specified ranges. Pay special attention to the absolute maximum ratings, operation voltage range and electrical characteristics, etc. SII Semiconductor Corporation is not re sponsible for damages caused by failu res and/or accidents, etc. that occur due to the use of products outside their specified ranges. 5. When using the products described herei n, confirm their applicatio ns, and the laws and regulat ions of the region or country where they are used and verify suitability, safety and other factors for the intended use. 6. When exporting the products described herein, comply with the Foreign Exchange and Foreign Trade Act and all other export-related laws, and follow the required procedures. 7. The products described herein must not be used or prov ided (exported) for the purposes of the development of weapons of mass destruction or militar y use. SII Semiconductor Corporation is not responsible for any provision (export) to those whose purpose is to develop, manufactur e, use or store nuclear, biol ogical or chemical weapons, missiles, or other military use. 8. The products described herein are not designed to be used as part of any device or equipment that may affect the human body, human life, or assets (such as medical equi pment, disaster prevention sy stems, security systems, combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do not use those products without the prior written permission of SII Semiconductor Corporation. Especially, the products described her ein cannot be used for life support dev ices, devices implanted in the human body and devices that directly affect human life, etc. Prior consultation with our sales office is required when considering the above uses. SII Semiconductor Corporation is not responsible for damages caused by unauthorized or unspecified use of our products. 9. Semiconductor products may fail or malfunction with some probability. The user of these products s hould therefore take responsibility to gi ve thorough consideration to safety design including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction. The entire system must be sufficiently evaluated and applied on customer's own responsibility. 10. The products described herein are not designed to be radi ation-proof. The necessary radiation measures should be taken in the product design by the customer depending on the intended use. 11. The products described herein do not affect human health under normal use. However, they contain chemical substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Take care when handling these with the bare hands to prevent injuries, etc. 12. When disposing of the products described herein, comply with the laws and ordinances of the country or region where they are used. 13. The information described herein contains copyright info rmation and know-how of SII Semiconductor Corporation. The information described herein does not convey any lic ense under any intellectual property rights or any other rights belonging to SII Semiconductor Corporation or a third party. Reproduction or copying of the information described herein for the purpose of disclosing it to a thir d-party without the express permission of SII Semiconductor Corporation is strictly prohibited. 14. For more details on the information de scribed herein, contact our sales office. 1.0-2016.01 www.sii-ic.com

Product Information

S8333 specifications and overview.

Summary

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER

Description

STEP-UP, FOR LCD BIAS SUPPLY, 1-CHANNEL, PWM CONTROL SWITCHING REGULATOR CONTROLLER

Source title S8333 Datasheet(PDF) - Seiko Instruments Inc

Related Parts

More parts from the same family.

Browse manufacturer