MP02X130

MP02X130 DYNEX | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

www.dynexsemi.com MP02X130 Series

FEATURES

I Electrically Isolated Package I Pressure Contact Construction I International Standard Footprint I Alumina (non-toxic) Isolation Medium

APPLICATIONS

I Controlled Rectifier Bridges I Heater Control I AC Phase Control VOLTAGE RATINGS

ORDERING INFORMATION

Order As: MP02HBT130-20 or MP02HBT130-18 or MP02HBT130-16 MP02HBP130-20 or MP02HBP130-18 or MP02HBP130-16 MP02HBN130-20 or MP02HBN130-18 or MP02HBN130-16 Note: When ordering, please use the complete part number. KEY PARAMETERS VDRM 2000V ITSM 4000A IT(AV)(per arm) 134A Visol 3000V MP02X130 Series Phase Control Dual SCR, SCR/Diode Modules Replaces January 2000 version, DS4477-4.0 DS4477-5.0 August 2001 Code Circuit HBT HBP HBN Fig.1 Circuit diagrams 12 3 Fig. 2 Electrical connections - (not to scale) Module type code: MP02. For further information see Package Details. Lower voltage grades available. Repetitive Peak Voltages VDRM VRRM Type Number 2000 1800 1600 MP02X130-20 MP02X130-18 MP02X130-16 T vj = 125oC IDRM = IRRM = 30mA VDSM & VRSM = VDRM & VRRM + 100V respectively Conditions

www.dynexsemi.com MP02X130 Series ABSOLUTE MAXIMUM RATINGS - PER ARM Stresses above those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. In extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability. Test Conditions Half wave resistive load T case = 75˚C Tcase = 85˚C Tcase = 75˚C 10ms half sine, Tj = 125˚C VR = 0 10ms half sine, Tj = 125˚C VR = 50% VDRM Commoned terminals to base plate. AC RMS, 1 min, 50Hz Symbol IT(AV) IT(RMS ITSM I2t ITSM I2t Visol Units A A A kA A kA A2s V Max. 134 112 210 4.0 80 x 103 3.2 51.2 x 103 3000 Parameter Mean on-state current RMS value Surge (non-repetitive) on-current I2t for fusing Surge (non-repetitive) on-current I 2t for fusing Isolation voltage Test Conditions dc Half wave

3 Phase

Mounting torque = 5Nm with mounting compound Reverse (blocking) Mounting - M6 Electrical connections - M6 Parameter Thermal resistance - junction to case (per thyristor or diode) Thermal resistance - case to heatsink (per thyristor or diode) Virtual junction temperature Storage temperature range Screw torque Weight (nominal) THERMAL AND MECHANICAL RATINGS Symbol R th(j-c) R th(c-hs) Tvj Tstg Units ˚C/kW ˚C/kW ˚C/kW ˚C/kW Nm (lb.ins) Nm (lb.ins) g Max. 0.21 0.22 0.23 0.07 125 125 6 (55) 5 (44) 350 Min. –40

www.dynexsemi.com MP02X130 Series Units mA V/µs A/µs V m Ω Test Conditions At VRRM /VDRM , Tj = 125˚C To 67% VDRM , Tj = 125˚C From 67% VDRM to 400A, Repetitive 50Hz gate source 20V, 20Ω , tr = 0.5µs, Tj = 125˚C At Tvj = 125˚C. See note 1 At Tvj = 125˚C. See note 1 Parameter Peak reverse and off-state current Linear rate of rise of off-state voltage Rate of rise of on-state current Threshold voltage On-state slope resistance DYNAMIC CHARACTERISTICS - THYRISTOR Symbol IRRM /IDRM dV/dt dI/dt VT(TO) rT Max. 1000 500 1.25 1.33 Min. Note 1: The data given in this datasheet with regard to forward voltage drop is for calculation of the power dissipation in the semiconductor elements only. Forward voltage drops measured at the power terminals of the module will be in excess of these figures due to the impedance of the busbar from the terminal to the semiconductor. Parameter Gate trigger voltage Gate trigger current Gate non-trigger voltage Peak forward gate voltage Peak forward gate voltage Peak reverse gate voltage Peak forward gate current Peak gate power Mean gate power Test Conditions V DRM = 5V, Tcase = 25oC VDRM = 5V, Tcase = 25oC VDRM = 5V, Tcase = 25oC Anode positive with respect to cathode Anode negative with respect to cathode Anode positive with respect to cathode See table fig. 5 Symbol VGT IGT VGD VFGM VFGN VRGM IFGM PGM PG(AV) GATE TRIGGER CHARACTERISTICS AND RATINGS Max. 3.0 200 0.2 0.25 Units V mA V V V V A W W

www.dynexsemi.com MP02X130 Series Fig. 6 Transient thermal impedance - dc Fig. 3 Maximum (limit) on-state characteristics Fig. 4 Surge (non-repetitive) on-state current vs time (Thyristor or diode with 50% VRRM at Tcase = 125˚C) Fig. 5 Gate characteristics 0 1.0 2.0 3.0 4.0 Instantaneous on-state voltage, VT - (V) 1000 800 600 400 200 Instantaneous on-state current, IT - (A) Tj = 125˚C 1 10 1 2 3 4 5 50 Duration Peak half sine wave on-state current - (kA) ms cycles at 50Hz I2t value - (A2s x 103) 30I2t

0.1 Gate voltage, VG - (V)

0.01 0.1 1 10 Gate current, IG - (A) Tj = –40˚C Tj = 125˚C Tj = 25˚C PGM = 16W 0.001 0.010 0.100 1.0 10 100 Time - (s) 0.1 0.2 0.3Thermal impedance - (˚C/W) R th(j-hs) R th(j-c)

www.dynexsemi.com MP02X130 Series Fig. 7 On-state power loss per arm vs on-state current at specified conduction angles, sine wave 50/60Hz Fig. 8 On-state power loss per arm vs on-state current at specified conduction angles, square wave 50/60Hz Fig. 9 Maximum permissible case temperature vs on-state current at specified conduction angles, sine wave 50/60Hz Fig. 10 Maximum permissible case temperature vs on-state current at specified conduction angles, square wave 50/60Hz 0 25 50 75 100 125 150 Mean on-state current, IT(AV) - (A) 300 200 100 On-state power loss per arm - (W) 180˚ 120˚ 90˚ 60˚ 30˚ 0 25 50 75 100 125 150 Mean on-state current, IT(AV) - (A) 300 200 100 On-state power loss per arm - (W) 180˚ 120˚ 90˚ 60˚ 30˚ d.c. 0 25 50 75 100 125 150 Mean on-state current, IT(AV) - (A) 120 100 Maximum permissible case temperature - (˚C) 180˚120˚ 90˚ 60˚30˚ 140 02 5 5 0 7 5 1 0 0 1 2 5 150 Mean on-state current, IT(AV) - (A) Maximum permissible case temperature - (˚C) d.c. 120 100 140

www.dynexsemi.com MP02X130 Series 0 40 80 0 20 40 60 80 120 140 160 180 100 200 600 500 400 300 200 100 Total power - (W) 1006020 Maximum ambient temperature - (˚C) D.C. output current - (A) R - Load L - Load 0.20 0.30 0.40 Fig. 11 50/60Hz single phase bridge dc output current vs power loss and maximum permissible ambient temperature for various values of heatsink thermal resistance (Note: Rth(hs-a) values given above are true heatsink thermal resistances to ambient and already account for Rth(c-hs) module contact thermal) Fig. 12 50/60Hz 3- phase bridge dc output current vs power loss and maximum permissible ambient temperature for various values of heatsink thermal resistance (Note: Rth(hs-a) values given above are true heatsink thermal resistances to ambient and already account for Rth(c-hs) module contact thermal) 04 0 8 0 600 500 400 300 200 100 Total power - (W) 1006020 Maximum ambient temperature - (˚C) D.C. output current - (A) 0.20 0.30 0.40 200 40 60 80 120 140 160 180100 200 R & L- Load

www.dynexsemi.com MP02X130 Series PACKAGE DETAILS For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless stated otherwise. DO NOT SCALE. 23 23 24 3x M6 12.8 2 holes Ø 6.5 12 3 515 K2 G 2 K1 G 1 Nominal weight: 350g Recommended fixings for mounting: M6 socket head cap screws Recommended mounting torque: 6Nm (55lb.ins) Recommended torque for electrical connections: 5Nm (44lb.ins) Maximum torque for electrical connections: 8Nm (70lb.ins) Module outline type code: MP02 12 3 K2 G 2 G 1 K1 12 3 Circuit type: HBN Circuit type: HBT Circuit type: HBP G 1 K1 12 3 K2 G 2 MOUNTING RECOMMENDATIONS Adequate heatsinking is required to maintain the base temperature at 75˚C if full rated current is to be achieved. Power dissipation may be calculated by use of VT(TO) and rT information in accordance with standard formulae. We can provide assistance with calculations or choice of heatsink if required. The heatsink surface must be smooth and flat; a surface finish of N6 (32µin) and a flatness within 0.05mm (0.002") are recommended. Immediately prior to mounting, the heatsink surface should be lightly scrubbed with fine emery, Scotch Brite or a mild chemical etchant and then cleaned with a solvent to remove oxide build up and foreign material. Care should be taken to ensure no foreign particles remain. An even coating of thermal compound (eg. Unial) should be applied to both the heatsink and module mounting surfaces. This should ideally be 0.05mm (0.002") per surface to ensure optimum thermal performance. After application of thermal compound, place the module squarely over the mounting holes, (or ‘T’ slots) in the heatsink. Fit and finger tighten the recommended fixing bolts at each end. Using a torque wrench, continue to tighten the fixing bolts by rotating each bolt in turn no more than 1/4 of a revolution at a time, until the required torque of 6Nm (55lbs.ins) is reached on all bolts at both ends. It is not acceptable to fully tighten one fixing bolt before starting to tighten the others. Such action may DAMAGE the module.

www.dynexsemi.com MP02X130 Series POWER ASSEMBLY CAPABILITY The Power Assembly group provides support for those customers requiring more than the basic semiconductor switch. Using CAD design tools the group has developed a flexible range of heatsink / clamping systems in line with advances in device types and the voltage and current capability of Dynex semiconductors. An extensive range of air and liquid cooled assemblies is available covering the range of circuit designs in general use today. HEATSINKS The Power Assembly group has a proprietary range of extruded aluminium heatsinks. These were designed to optimise the performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or customer service office. CUSTOMER SERVICE CENTRES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 North America Tel: (613) 723-7035. Fax: (613) 723-1518. UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 SALES OFFICES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 Tel: (949) 733-3005. Fax: (949) 733-2986. UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 These offices are supported by Representatives and Distributors in many countries world-wide. © Dynex Semiconductor 2001 Publication No. DS4477-5 Issue No. 5.0 August 2001 TECHNICAL DOCUMENTATION – NOT FOR RESALE. PRINTED IN UNITED KINGDOM HEADQUARTERS OPERATIONS DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln. Lincolnshire. LN6 3LF. United Kingdom. Tel: 00-44-(0)1522-500500 Fax: 00-44-(0)1522-500550 DYNEX POWER INC.

99 Bank Street, Suite 410,

Ottawa, Ontario, Canada, K1P 6B9 Tel: 613.723.7035 Fax: 613.723.1518 Toll Free: 1.888.33.DYNEX (39639) This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. http://www.dynexsemi.com e-mail: power_solutions@dynexsemi.com Datasheet Annotations: Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:- Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started. Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change. Advance Information: The product design is complete and final characterisation for volume production is well in hand. No Annotation: The product parameters are fixed and the product is available to datasheet specification.