MGM210L SILABS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 45

Technical content

MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet The MGM210L is a module designed and built to meet the per- formance, security, and reliability requirements of line-powered, smart LED lighting products. Based on the EFR32MG21 Gecko SoC, it enables Zigbee®, Thread®, Bluetooth® and multi-protocol connectivity (Zigbee + Bluetooth) delivering best-in-class RF performance, CA Title 20 energy consumption compliance, future-proof capability for feature and OTA firmware updates, enhanced security, and a form factor and temperature rating suited for enclosed operation in lightbulb housings. The MGM210L is a complete solution that comes with fully-upgradeable, robust software stacks, world-wide regulatory certifications, advanced development and debugging tools, and support that will simplify and minimize the development cycle and deployment of your product helping to accelerate its time-to-market. The MGM210L is targeted for key applications that include:

  • Smart LED lightbulbs
  • Connected lighting KEY FEATURES
  • Zigbee, Thread, Bluetooth 5.3 and multi- protocol connectivity
  • PCB Trace antenna
  • +12.5 dBm max TX power
  • -104 dBm 802.15.4 RX sensitivity
  • -97 dBm Bluetooth RX sensitivity @ 1 Mbps
  • 32-bit ARM Cortex-M33 core at 38.4 MHz
  • 1024/96 kB of flash/RAM memory
  • Enhanced security features
  • Optimal set of MCU peripherals
  • 12 GPIO pins
  • -40 to (105 or 125)°C
  • 15.5 mm x 22.5 mm (custom form factor) Timers and Triggers 32-bit bus Peripheral Reflex System Serial Interfaces I/O Ports Analog I/F Lowest power mode with peripheral operational: USART I2C External Interrupts General Purpose I/O Pin Reset Pin Wakeup ADC Analog Comparator EM4—Shutoff Energy Management Brown-Out Detector Voltage Regulator Power-On Reset SecurityClock Management HF Crystal Oscillator LF RC Oscillator HF RC Oscillator EM23 HF RC Oscillator Crypto Acceleration Secure Debug Security Core Ultra LF RC Oscillator Core / Memory ARM CortexTM M33 processor with DSP extensions, FPU and TrustZone ETM Debug InterfaceRAM Memory LDMA Controller Flash Program Memory Real Time Capture Counter Timer/Counter Low Energy Timer Watchdog Timer Protocol Timer Radio Transceiver DEMOD AGC IFADC CRC BUFC MOD FRC RAC Frequency Synth PGA EM3—StopEM2—Deep SleepEM1—SleepEM0—Active True Random Number Generator Fast Startup RC Oscillator Back-Up Real Time Counter RF Frontend I Q PA LNA PA Crystal 38.4 MHz Antenna PCB Trace Antenna Matching LF Crystal Oscillator silabs.com | Building a more connected world. Copyright © 2022 by Silicon Laboratories Rev. 1.2
  1. Features
  • Supported Protocols
  • Zigbee
  • Thread
  • Bluetooth 5.3
  • Bluetooth Mesh
  • Multi-protocol (Zigbee + Bluetooth 5.3)
  • Wireless System-on-Chip
  • 2.4 GHz radio
  • TX power up to +12.5 dBm
  • 32-bit ARM Cortex®-M33 with DSP instruction and floating- point unit for efficient signal processing
  • 1024 kB flash program memory
  • 96 kB RAM data memory
  • Embedded Trace Macrocell (ETM) for advanced debugging
  • Receiver Performance
  • -104 dBm sensitivity (1% PER) at 250 kbps O-QPSK DSSS
  • -104.4 dBm sensitivity (0.1% BER) at 125 kbps GFSK
  • -100.1 dBm sensitivity (0.1% BER) at 500 kbps GFSK
  • -97 dBm sensitivity (0.1% BER) at 1 Mbps GFSK
  • -93.9 dBm sensitivity (0.1% BER) at 2 Mbps GFSK
  • Current Consumption
  • 9.4 mA RX current at 250 kbps O-QPSK DSSS
  • 9.3mA RX current at 1 Mbps GFSK
  • 70 mA TX current at 12.5 dBm output power
  • 50.9 µA/MHz in Active Mode (EM0)
  • 5.1 μA EM2 DeepSleep current (RTCC running from LFXO, Bluetooth Stack not running)
  • 8.5 μA EM2 DeepSleep current (RTCC running from LFXO, Bluetooth Stack running)
  • Regulatory Certifications
  • CE, UKCA, Serbia
  • ISED, FCC, Dominican Republic, Mexico
  • Japan, South Korea, Taiwan
  • Australia
  • China, Hong Kong, Singapore, Thailand
  • Bahrain, Israel, Jordan, Kuwait, Qatar, UAE, Oman, Saudi Arabia
  • Egypt, Morocco
  • Operating Range
  • 1.8 to 3.8 V
  • -40 to +105°C or -40 to +125°C
  • Dimensions
  • 15.5 mm x 22.5 mm (custom form factor)
  • Security
  • Secure Boot with Root of Trust and Secure Loader (RTSL)1
  • Hardware Cryptographic Acceleration with DPA counter- measures1 for AES128/256, SHA-1, SHA-2 (up to 256-bit), ECC (up to 256-bit), ECDSA, and ECDH
  • True Random Number Generator (TRNG) compliant with NIST SP800-90 and AIS-31
  • ARM® TrustZone®
  • Secure Debug Interface lock/unlock
  • MCU Peripherals
  • 12-bit 1 Msps SAR Analog to Digital Converter (ADC)
  • 2 × Analog Comparator (ACMP)
  • 12 General Purpose I/O pins with output state retention and asynchronous interrupts
  • 8 Channel DMA Controller
  • 12 Channel Peripheral Reflex System (PRS)
  • 3 × 16-bit Timer/Counter (3 Compare/Capture/PWM channels)
  • 1 × 32-bit Timer/Counter (3 Compare/Capture/PWM channels)
  • 32-bit Real Time Counter
  • 24-bit Low Energy Timer for waveform generation
  • 2 × Watchdog Timer
  • 3 × Universal Synchronous/Asynchronous Receiver/Trans- mitter (UART/SPI/SmartCard (ISO 7816)/IrDA/I2S)
  • 2 × I2C interface with SMBus support 1. With Secure Element (SE) firmware v1.1.2 or newer MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet

Features

silabs.com | Building a more connected world. Rev. 1.2 | 2

  1. Ordering Information Table 2.1. Ordering Information Ordering Code Protocol Stack Max TX Power Freq Band Antenna Flash (kB) RAM (kB) GPIO Temp Range Packaging MGM210LA22JIF2 • Zigbee
  • Thread
  • Bluetooth 5.3 12.5 dBm 2.4 GHz Inverted-F PCB Trace 1024 96 12 -40 to 125 °C Cut Tape MGM210LA22JIF2R • Zigbee
  • Thread
  • Bluetooth 5.3 12.5 dBm 2.4 GHz Inverted-F PCB Trace 1024 96 12 -40 to 125 °C Reel MGM210LA22JNF2 • Zigbee
  • Thread
  • Bluetooth 5.3 12.5 dBm 2.4 GHz Inverted-F PCB Trace 1024 96 12 -40 to 105 °C Cut Tape MGM210LA22JNF2R • Zigbee
  • Thread
  • Bluetooth 5.3 12.5 dBm 2.4 GHz Inverted-F PCB Trace 1024 96 12 -40 to 105 °C Reel End-product manufacturers must verify that the module is configured to meet regulatory limits for each region in accordance with the formal certification test reports. MGM210L modules are pre-programmed with UART XMODEM bootloader. SLWRB4309B radio board is available for MGM210L evaluation and development. The modules may be referred to by their product family name ( MGM210L), model name (MGM210L22F) or full ordering code through- out this document. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet

Ordering Information

silabs.com | Building a more connected world. Rev. 1.2 | 3

silabs.com | Building a more connected world. Rev. 1.2 | 4

silabs.com | Building a more connected world. Rev. 1.2 | 5

  1. System Overview

3.1 Block Diagram

The MGM210L module is a highly-integrated, high-performance system with all the hardware components needed to enable 2.4 GHz wireless connectivity and support robust networking capabilities via multiple protocols. Built around the EFR32MG21 Wireless Gecko SoC, the MGM210L includes a built-in PCB trace antenna, an RF matching network (op- timized for transmit power efficiency), supply decoupling and filtering components, a 38.4 MHz reference crystal, and an RF shield. A general block diagram of the module is shown below. DEC Silicon Labs EFR32MG21 HF XTAL Supply Decoupling RF SHIELD VDD GPIO GND (up to 12)RF Match Antenna LPF Figure 3.1. MGM210L Block Diagram

3.2 EFR32MG21 SoC

The EFR32MG21 SoC features a 32-bit ARM Cortex M33 core, a 2.4 GHz high-performance radio, 1 MB of Flash memory, a dedicated core for security, a rich set of MCU peripherals, and various clock management and serial interfacing options. Consult the EFR32xG21 Wireless Gecko Reference Manual and the EFR32MG21 Data Sheet for details.

3.3 Antenna

MGM210L modules include a meandered inverted-F antenna (MIFA) with the characteristics seen below. Table 3.1. Antenna Efficiency and Peak Gain Parameter With optimal layout Note Efficiency -2 to -2.5 dB Antenna efficiency, gain and radiation pattern are highly depend- ent on the application PCB layout and mechanical design. Refer to Section 7. Design Guidelines for PCB layout and antenna inte- gration guidelines to achieve optimal performance. Peak gain 0.5 dBi

3.4 Power Supply

The MGM210L requires a single nominal supply level of 3.0 V. All the necessary decoupling and filtering components are included in the module. The module can tolerate supply voltage noise of up to 700 mVpp. The supply voltage is filtered internally in the module with a 100 kHz low-pass filter to guarantee operation across the full supply range of 1.8 to 3.8 V. Additional external filtering is neither required nor recommended as it may cause voltage drops below the minimum level tolerable by the SoC (1.71 V) during transmit bursts. For typical use cases, the decouple pin (DEC) should be left disconnected. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet System Overview silabs.com | Building a more connected world. Rev. 1.2 | 6

  1. Electrical Specifications

4.1 Electrical Characteristics

All electrical parameters in all tables are specified under the following conditions, unless stated otherwise:

  • Typical values are based on TA=25 °C and VDD = 3.0 V, by production test and/or technology characterization.
  • Radio performance numbers are measured in conducted mode, based on Silicon Laboratories reference designs using output pow- er-specific external RF impedance-matching networks for interfacing to a 50 Ω antenna.
  • Minimum and maximum values represent the worst conditions across supply voltage, process variation, and operating temperature, unless stated otherwise.

4.1.1 Absolute Maximum Ratings

Stresses above those listed below may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. For more information on the available quality and relia- bility data, see the Quality and Reliability Monitor Report at http://www.silabs.com/support/quality/pages/default.aspx. Table 4.1. Absolute Maximum Ratings Parameter Symbol Test Condition Min Typ Max Unit Storage temperature range TSTG -50 — +150 °C Voltage on VDD supply pin VDDMAX -0.3 — 3.8 V Voltage ramp rate on VDD supply pin VDDRAMPMAX — — 1.0 V / µs DC voltage on any GPIO pin VDIGPIN -0.3 — VDD + 0.3 V Total current into VDD pin IVDDMAX Source — — 200 mA Total current into GND pin IGNDMAX Sink — — 200 mA Current per I/O pin IIOMAX Sink — — 50 mA Source — — 50 mA Current for all I/O pins IIOALLMAX Sink — — 200 mA Source — — 200 mA Junction temperature TJMAX — — +125 °C MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 7

4.1.2 General Operating Conditions

This table specifies the general operating temperature range and supply voltage range for all supplies. The minimum and maximum values of all other tables are specifed over this operating range, unless otherwise noted. Table 4.2. General Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Operating ambient tempera- ture range TA -N temperature grade -40 — +105 °C -I temperature grade -40 — +125 ° C VDD Supply Voltage VDD 1.8 3.0 3.8 V HCLK and Core frequency fHCLK MODE = WS1, RAMWSEN = 11 — — 80 MHz MODE = WS1, RAMWSEN = 01 — — 50 MHz MODE = WS0, RAMWSEN = 01 — — 39 MHz PCLK frequency fPCLK — — 50 MHz EM01 Group A clock fre- quency fEM01GRPACLK — — 80 MHz HCLK Radio frequency fHCLKRADIO — 38.4 — MHz Note: 1. Flash wait states are set by the MODE field in the MSC_READCTRL register. RAM wait states are enabled by setting the RAMW- SEN bit in the SYSYCFG_DMEM0RAMCTRL register. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 8

4.1.3 MCU Current Consumption at 3.0V Unless otherwise indicated, typical conditions are: VDD = 3.0 V. T A = 25 °C. Minimum and maximum values in this table represent the worst conditions across process variation at TA = 25 °C. Table 4.3. MCU Current Consumption at 3.0V Parameter Symbol Test Condition Min Typ Max Unit Current consumption in EM0 mode with all peripherals dis- abled1 IACTIVE 80 MHz HFRCO, CPU running Prime from flash — 50.9 — µA/MHz

80 MHz HFRCO, CPU running

— 45.6 55.5 µA/MHz — 59.8 — µA/MHz

38.4 MHz crystal, CPU running

— 63.8 — µA/MHz Current consumption in EM1 mode with all peripherals dis- abled1 IEM1 80 MHz HFRCO — 28.7 37.6 µA/MHz 38.4 MHz crystal — 46.9 — µA/MHz Current consumption in EM2 mode IEM2 Full RAM retention and RTC run- ning from LFXO (Bluetooth Stack not running) — 5.1 — µA Full RAM retention, RTCC run- ning, and Bluetooth Stack running from LFXO — 8.5 — µA 1 bank (16 kB) RAM retention and RTC running from LFRCO — 4.5 10.5 µA Current consumption in EM3 mode IEM3 Full RAM retention and RTC run- ning from ULFRCO — 4.8 11.4 µA 1 bank (16 kB) RAM retention and RTC running from ULFRCO — 4.3 — µA Current consumption in EM4 mode IEM4 No BURTC, no LF oscillator — 0.21 0.5 µA Current consumption during reset IRST Hard pin reset held — 146 — µA Current consumption per re- tained 16kB RAM bank in EM2 IRAM — 0.10 — µA Note: 1. The typical EM0/EM1 current measurement includes some current consumed by the security core for periodical housekeeping purposes. This does not include current consumed by user-triggered security operations, such as cryptographic calculations. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 9

4.1.4 Radio Current Consumption at 3.0V RF current consumption measured with MCU in EM1, HCLK = 38.4 MHz, and all MCU peripherals disabled. Unless otherwise indica- ted, typical conditions are: VDD = 3.0V. T A = 25 °C. Minimum and maximum values in this table represent the worst conditions across process variation at TA = 25 °C. Table 4.4. Radio Current Consumption at 3.0V Parameter Symbol Test Condition Min Typ Max Unit Current consumption in re- ceive mode, active packet reception IRX_ACTIVE 125 kbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.3 — mA 500 kbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.3 — mA 1 Mbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.3 — mA 2 Mbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.9 — mA 802.15.4 receiving frame, f = 2.4 GHz, ZigBee stack running — 9.4 — mA Current consumption in re- ceive mode, Stack running IRX_LISTEN 125 kbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.1 — mA 500 kbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.1 — mA 1 Mbit/s, 2GFSK, f = 2.4 GHz, Bluetooth stack running — 9.1 — mA 2 Mbit/s, 2GFSK, f = 2.4 GHz, Bluetooh stack running — 9.8 — mA 802.15.4, f = 2.4 GHz, ZigBee stack running — 9.2 — mA Current consumption in transmit mode ITX f = 2.4 GHz, CW, 12.5 dBm output power, VDD = 3.3 V — 70 — mA MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 10

4.1.5 RF Transmitter General Characteristics for the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. 1 Table 4.5. RF Transmitter General Characteristics for the 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit RF tuning frequency range FRANGE Frequency Range for Bluetooth Low-Energy 2402 — 2480 MHz Frequency Range for ZigBee 2405 — 2480 MHz Maximum TX power 23 POUTMAX 12 dBm PA, VDD = 3.3 V — 12.5 — dBm Minimum active TX Power POUTMIN 12 dBm PA, VDD = 3.3 V — -20.5 — dBm Output power variation vs VDD supply voltage varia- tion, frequency = 2450MHz POUTVAR_V 12 dBm PA Pout = POUTMAX out- put power with VDD voltage swept from 3.8V to 3.0V. — +/- 0.5 — dB 12 dBm PA Pout = POUTMAX out- put power with VDD voltage swept from 3.8V to 1.8V — +0.5/-4.5 — dB Output power variation vs RF frequency POUTVAR_F 12 dBm PA, POUTMAX, VDD = 3.3 V. — +/- 0.1 — dB Note: 1. For regulatory compliance please refer to the official certification test reports 2. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices cov- ered in this data sheet can be found in the TX Power column of the Ordering Information Table. 3. The maximum TXP to comply with ETSI PSD and EIRP limits depend on antenna gain which in turn depend on the end product mechanical design. In optimal conditions the module is compliant to the ETSI PSD and EIRP limits at maximum TXP of 8.2 dBm. End product manufacturer must ensure compliance to the limits for CE marking of the end product. Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Parameter Symbol Test Condition Min Typ Max Unit Error vector magnitude per 802.15.4-2011 EVM Average across frequency, signal is DSSS-OQPSK reference pack- et, VDD = 3.3 V, Pout = POUTMAX — 2.7 — % rms 4.1.7 RF Receiver General Characteristics for the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.7. RF Receiver General Characteristics for the 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit RF tuning frequency range FRANGE 2400 — 2483.5 MHz MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 11

Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 1% PER SAT Signal is reference signal1, packet length is 20 octets — 10 — dBm Sensitivity, 1% PER SENS Signal is reference signal, packet length is 20 octets — -104 — dBm Co-channel interferer rejec- tion, 1% PER CCR Desired signal 3 dB above sensi- tivity limit — -0.2 — dB Adjacent channel rejection, Interferer is reference signal, 1% PER, desired is refer- ence signal at 3 dB above reference sensitivity level2 ACRREF1 Interferer is reference signal at +1 channel spacing — 39.9 — dB Interferer is reference signal at -1 channel spacing — 39.2 — dB Alternate channel rejection, interferer is reference signal, 1% PER, desired is refer- ence signal at 3 dB above reference sensitivity level2 ACRREF2 Interferer is reference signal at +2 channel spacing — 51.1 — dB Interferer is reference signal at -2 channel spacing — 51.6 — dB Image rejection, 1% PER, desired is reference signal at 3 dB above reference sensi- tivity level2 IR Interferer is CW in image band3 — 43.5 — dB Blocking rejection of all other channels, 1% PER, desired is reference signal at 3 dB above reference sensitivity level2, interferer is reference signal BLOCK Interferer frequency < desired fre- quency -3 channel spacing — 57.6 — dB Interferer frequency > desired fre- quency +3 channel spacing — 57.5 — dB RSSI resolution RSSIRES -100 dBm to +5 dBm — 0.25 — dB RSSI accuracy in the linear region as defined by 802.15.4-2003 RSSILIN — +/-6 — dB Note: bols/s. 2. Reference sensitivity level is -85 dBm. 3. Due to low-IF frequency, there is some overlap of adjacent channel and image channel bands. Adjacent channel CW blocker tests place the Interferer center frequency at the Desired frequency ± 5 MHz on the channel raster, whereas the image rejection test places the CW interferer near the image frequency of the Desired signal carrier, regardless of the channel raster. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 12

4.1.9 RF Receiver Characteristics for Bluetooth Low Energy at 1 Mbps

Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.9. RF Receiver Characteristics for Bluetooth Low Energy at 1 Mbps Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level SAT Signal is reference signal, packet length is 37 bytes1 — 10 — dBm Sensitivity SENS Signal is reference signal, 37 byte payload1 — -97 — dBm With non-ideal signals2 1 — -96.5 — dBm Signal to co-channel interfer- er C/ICC (see notes)1 3 — +6.6 — dB N ± 1 Adjacent channel se- lectivity C/I1 Interferer is reference signal at +1 MHz offset1 4 3 5 — -8.3 — dB Interferer is reference signal at -1 MHz offset1 4 3 5 — -8.7 — dB N ± 2 Alternate channel se- lectivity C/I2 Interferer is reference signal at +2 MHz offset1 4 3 5 — -42.1 — dB Interferer is reference signal at -2 MHz offset1 4 3 5 — -48.9 — dB N ± 3 Alternate channel se- lectivity C/I3 Interferer is reference signal at +3 MHz offset1 4 3 5 — -42.4 — dB Interferer is reference signal at -3 MHz offset1 4 3 5 — -54.8 — dB Selectivity to image frequen- cy C/IIM Interferer is reference signal at im- age frequency with 1 MHz preci- sion1 5 — -42.1 — dB Selectivity to image frequen- cy ± 1 MHz C/IIM_1 Interferer is reference signal at im- age frequency +1 MHz with 1 MHz precision1 5 — -42.4 — dB Interferer is reference signal at im- age frequency -1 MHz with 1 MHz precision1 5 — -8.3 — dB Intermodulation performance IM n = 3 6 — -23 — dBm Note: 1. 0.1% Bit Error Rate. 3. Desired signal -67 dBm. 4. Desired frequency 2402 MHz ≤ Fc ≤ 2480 MHz. 5. With allowed exceptions. 6. As specified in Bluetooth Core specification version 5.1, Vol 6, Part A, Section 4.4 MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 13

4.1.10 RF Receiver Characteristics for Bluetooth Low Energy at 2 Mbps

Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.10. RF Receiver Characteristics for Bluetooth Low Energy at 2 Mbps Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level SAT Signal is reference signal, packet length is 37 bytes1 — 10 — dBm Sensitivity SENS Signal is reference signal, 37 byte payload1 — -93.9 — dBm With non-ideal signals2 1 — -93.4 — dBm Signal to co-channel interfer- er C/ICC (see notes)1 3 — +6.0 — dB N ± 1 Adjacent channel se- lectivity C/I1 Interferer is reference signal at +2 MHz offset1 4 3 5 — -8.0 — dB Interferer is reference signal at -2 MHz offset1 4 3 5 — -8.8 — dB N ± 2 Alternate channel se- lectivity C/I2 Interferer is reference signal at +4 MHz offset1 4 3 5 — -42.2 — dB Interferer is reference signal at -4 MHz offset1 4 3 5 — -50.3 — dB N ± 3 Alternate channel se- lectivity C/I3 Interferer is reference signal at +6 MHz offset1 4 3 5 — -54.4 — dB Interferer is reference signal at -6 MHz offset1 4 3 5 — -55.4 — dB Selectivity to image frequen- cy C/IIM Interferer is reference signal at im- age frequency with 1 MHz preci- sion1 5 — -8.0 — dB Selectivity to image frequen- cy ± 1 MHz C/IIM_1 Interferer is reference signal at im- age frequency +2 MHz with 1 MHz precision1 5 — -42.2 — dB Interferer is reference signal at im- age frequency -2 MHz with 1 MHz precision1 5 — +6.0 — dB Intermodulation performance IM n = 36 — -22.3 — dBm Note: 1. 0.1% Bit Error Rate. 3. Desired signal -67 dBm. 4. Desired frequency 2402 MHz ≤ Fc ≤ 2480 MHz. 5. With allowed exceptions. 6. As specified in Bluetooth Core specification version 5.1, Vol 6, Part A, Section 4.4 MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 14

4.1.11 RF Receiver Characteristics for Bluetooth Low Energy at 500 kbps

Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.11. RF Receiver Characteristics for Bluetooth Low Energy at 500 kbps Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level SAT Signal is reference signal, packet length is 37 bytes1 — 10 — dBm Sensitivity SENS Signal is reference signal1 — -100.1 — dBm With non-ideal signals2 1 — -99.5 — dBm Signal to co-channel interfer- er C/ICC (see notes)1 3 — +2.1 — dB N ± 1 Adjacent channel se- lectivity C/I1 Interferer is reference signal at +1 MHz offset1 4 3 5 — -9.0 — dB Interferer is reference signal at -1 MHz offset1 4 3 5 — -9.5 — dB N ± 2 Alternate channel se- lectivity C/I2 Interferer is reference signal at +2 MHz offset1 4 3 5 — -44.4 — dB Interferer is reference signal at -2 MHz offset1 4 3 5 — -51.9 — dB N ± 3 Alternate channel se- lectivity C/I3 Interferer is reference signal at +3 MHz offset1 4 3 5 — -44.3 — dB Interferer is reference signal at -3 MHz offset1 4 3 5 — -58.3 — dB Selectivity to image frequen- cy C/IIM Interferer is reference signal at im- age frequency with 1 MHz preci- sion1 5 — -44.4 — dB Selectivity to image frequen- cy ± 1 MHz C/IIM_1 Interferer is reference signal at im- age frequency +1 MHz with 1 MHz precision1 5 — -44.3 — dB Interferer is reference signal at im- age frequency -1 MHz with 1 MHz precision1 5 — -9.0 — dB Note: 1. 0.1% Bit Error Rate. 3. Desired signal -72 dBm. 4. Desired frequency 2402 MHz ≤ Fc ≤ 2480 MHz. 5. With allowed exceptions. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 15

4.1.12 RF Receiver Characteristics for Bluetooth Low Energy at 125 kbps

Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.12. RF Receiver Characteristics for Bluetooth Low Energy at 125 kbps Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level SAT Signal is reference signal, packet length is 37 bytes1 — 10 — dBm Sensitivity SENS Signal is reference signal1 — -104.4 — dBm With non-ideal signals2 1 — -104.1 — dBm Signal to co-channel interfer- er C/ICC (see notes)1 3 — +0.8 — dB N ± 1 Adjacent channel se- lectivity C/I1 Interferer is reference signal at +1 MHz offset1 4 3 5 — -13.1 — dB Interferer is reference signal at -1 MHz offset1 4 3 5 — -13.6 — dB N ± 2 Alternate channel se- lectivity C/I2 Interferer is reference signal at +2 MHz offset1 4 3 5 — -49.5 — dB Interferer is reference signal at -2 MHz offset1 4 3 5 — -56.9 — dB N ± 3 Alternate channel se- lectivity C/I3 Interferer is reference signal at +3 MHz offset1 4 3 5 — -47.0 — dB Interferer is reference signal at -3 MHz offset1 4 3 5 — -63.1 — dB Selectivity to image frequen- cy C/IIM Interferer is reference signal at im- age frequency with 1 MHz preci- sion1 5 — -49.5 — dB Selectivity to image frequen- cy ± 1 MHz C/IIM_1 Interferer is reference signal at im- age frequency +1 MHz with 1 MHz precision1 5 — -47.0 — dB Interferer is reference signal at im- age frequency -1 MHz with 1 MHz precision1 5 — -13.1 — dB Note: 1. 0.1% Bit Error Rate. 3. Desired signal -79 dBm. 4. Desired frequency 2402 MHz ≤ Fc ≤ 2480 MHz. 5. With allowed exceptions. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 16

4.1.13 High-Frequency Crystal

Table 4.13. High-Frequency Crystal Parameter Symbol Test Condition Min Typ Max Unit Crystal frequency fHFXTAL — 38.4 — MHz Initial calibrated accuracy ACCHFXTAL -10 — +10 ppm Temperature drift DRIFTHFXTAL Across specified temperature range -30 — +30 ppm MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 17

4.1.14 GPIO Pins

Unless otherwise indicated, typical conditions are: VDD = 3.0 V. Table 4.14. GPIO Pins Parameter Symbol Test Condition Min Typ Max Unit Leakage current ILEAK_IO MODEx = DISABLED, VDD = 1.71V — 1.9 — nA MODEx = DISABLED, VDD = 3.0 V — 2.5 — nA MODEx = DISABLED, VDD = 3.8 V TA = 125 °C — — 200 nA Input low voltage VIL Any GPIO pin and RESETn — — 0.3 * VDD V Input high voltage VIH Any GPIO pin and RESETn 0.7 * VDD — — V Output low voltage VOL Sinking 20mA, VDD = 3.0 V — — 0.2 * VDD V Sinking 8mA, VDD = 1.62 V — — 0.4 * VDD V Output high voltage VOH Sourcing 20mA, VDD = 3.0 V 0.8 * VDD — — V Sourcing 8mA, VDD = 1.62 V 0.6 * VDD — — V GPIO rise time TGPIO_RISE VDD = 3.0V, Cload = 50pF, SLEW- RATE = 4, 10% to 90% — 8.4 — ns VDD = 1.7V, Cload = 50pF, SLEW- RATE = 4, 10% to 90% — 13 — ns GPIO fall time TGPIO_FALL VDD = 3.0V, Cload = 50pF, SLEW- RATE = 4, 90% to 10% — 7.1 — ns VDD = 1.7V, Cload = 50pF, SLEW- RATE = 4, 90% to 10% — 11.9 — ns Pull up/down resistance1 RPULL pull-up: MODEn = DISABLE DOUT=1, pull-down: MODEn = WIREDORPULLDOWN DOUT = 35 44 55 kΩ Maximum filtered glitch width TGF MODE = INPUT, DOUT = 1 — 26 — ns RESETn low time to ensure pin reset TRESET 100 — — ns Note: 1. GPIO and RESETn pull-ups connect to the VDD supply. Pull-downs on GPIO connect to VSS. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 18

4.1.15 Microcontroller Peripherals

The MCU peripherals set available in MGM210L modules includes:

  • 12-bit 1 Msps ADC
  • Analog Comparators
  • 16-bit and 32-bit Timers/Counters
  • 24-bit Low Energy Timer for waveform generation
  • 32-bit Real Time Counter
  • USART (UART/SPI/SmartCards/IrDA/I2S)
  • I2C peripheral interfaces
  • 12 Channel Peripheral Reflex System For details on their electrical performance, consult the relevant portions of Section 4 in the SoC datasheet. To learn which GPIO ports provide access to every peripheral, consult Section 6.3 Analog Peripheral Connectivity and Section 6.4 Digital Peripheral Connectivity.

4.2 Typical Performance Curves

Typical performance curves indicate typical characterized performance under the stated conditions. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 19

4.2.1 Antenna Radiation and Efficiency

Typical MGM210L antenna radiation patterns and efficiency under optimal operating conditions are plotted in the figure below. Antenna gain and radiation patterns have a strong dependence on the size and shape of the application PCB the module is mounted on and, also, on the proximity of any mechanical design to the antenna. Figure 4.1. Typical 2D Antenna Radiation Patterns and Efficiency Top Left: Phi 0o, Top Right: Phi 90o, Bottom Left: Theta 90o, Bottom Right: Radiation Efficiency MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Electrical Specifications silabs.com | Building a more connected world. Rev. 1.2 | 20

  1. Reference Diagrams A typical application circuit for the MGM210L module is shown below. xGM210L PC04 16 PC03 15 PC02 14 GND 13 VDD DNC RESET PD01 PC01 PC00 GND DEC PA03 PA02 PA01 PA04 PC05 PD00 U1 SWCLK SWDIO SWO/TDO TDI UART_TX UART_RX RESET GPIO GPIO VDD MINI SIMPLICITY CONNECTOR FOR DEBUGGING 7 8 9 10 HEADER_10PIN_1.27MM_SMD_DUAL UART_RX SWO/TDO SWCLK PTI_DATA VDD UART_RTS UART_CTS PTI_DATA PTI_SYNC UART_TX RESET SWDIO PTI_SYNC Figure 5.1. MGM210L Application Schematic Interconnection labels correspond to supported pin functions described in 7.4 Debug, 7.5 Packet Trace Interface (PTI) and 6.4 Digital Peripheral Connectivity. Placing the module horizontally on the end-application board permits access to all module pins. Placing it vertically restricts access to pins 13 through 18 only. The reference schematic above is applicable for the former case only. Refer to 7. Design Guidelines for more details. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Reference Diagrams silabs.com | Building a more connected world. Rev. 1.2 | 21
  1. Pin Definitions

6.1 Module Pinout

Figure 6.1. MGM210L Lighting Module Pinout The next table shows the MGM210L pinout and general descriptions for each pin. Refer to 6.2 Alternate Pin Functions, 6.3 Analog Pe- ripheral Connectivity, and 6.4 Digital Peripheral Connectivity for details on functions and peripherals supported by GPIOs. Table 6.1. MGM210L Lighting Module Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description PA01 1 GPIO/Debug PA02 2 GPIO/Debug PA03 3 GPIO/Debug PA04 4 GPIO/Debug DEC 5 Decouple1 GND 6 Ground PC00 7 GPIO PC01 8 GPIO PD01 9 GPIO PD00 10 GPIO RESETn 11 Reset Pin3 DNC 12 Do not connect VDD 13 VDD GND 14 Ground PC02 15 GPIO2 PC03 16 GPIO2 PC04 17 GPIO2 PC05 18 GPIO2 Note: 1. Available for powering module through external PMIC. Should be left disconnected typically. Do not use Decouple supply to pow- er external circuitry. 2. Internally terminated with series 56 ohm resistor. 3. Connected to pull-up resistor to VDD internally. External pull-up is not required. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Pin Definitions silabs.com | Building a more connected world. Rev. 1.2 | 22

6.2 Alternate Pin Functions

Some GPIOs support alternate functions like debugging, wake-up from EM4, access to an external low frequency crystal, etc.. The fol- lowing table shows which module pins have alternate capabilities and the functions they support. Refer to the SoC's reference manual for more information. Table 6.2. GPIO Alternate Functions Table GPIO Alternate Function PA01 GPIO.SWCLK PA02 GPIO.SWDIO PA03 GPIO.SWV GPIO.TDO GPIO.TRACEDATA0 PA04 GPIO.TDI GPIO.TRACECLK PC00 GPIO.EM4WU6 PD01 LFXO.LFXTAL_I LFXO.LF_EXTCLK PD00 LFXO.LFXTAL_O PC05 GPIO.EM4WU7

6.3 Analog Peripheral Connectivity

Many analog resources are routable and can be connected to numerous GPIO's. The table below indicates which peripherals are avali- able on each GPIO port. When a differential connection is being used Positive inputs are restricted to the EVEN pins and Negative inputs are restricted to the ODD pins. When a single ended connection is being used positive input is avaliable on all pins. See the device Reference Manual for more details on the ABUS and analog peripherals. Table 6.3. ABUS Routing Table Peripheral Signal PA PC PD EVEN ODD EVEN ODD EVEN ODD ACMP0 ana_neg Yes Yes Yes Yes Yes Yes ana_pos Yes Yes Yes Yes Yes Yes ACMP1 ana_neg Yes Yes Yes Yes Yes Yes ana_pos Yes Yes Yes Yes Yes Yes IADC0 ana_neg Yes Yes Yes Yes Yes Yes ana_pos Yes Yes Yes Yes Yes Yes MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Pin Definitions silabs.com | Building a more connected world. Rev. 1.2 | 23

6.4 Digital Peripheral Connectivity

Many digital resources are routable and can be connected to numerous GPIO's. The table below indicates which peripherals are avalia- ble on each GPIO port. Table 6.4. DBUS Routing Peripheral.Resource PORT PA PC PD ACMP0.DIGOUT Available Available Available ACMP1.DIGOUT Available Available Available CMU.CLKIN0 Available Available CMU.CLKOUT0 Available Available CMU.CLKOUT1 Available Available CMU.CLKOUT2 Available FRC.DCLK Available Available FRC.DFRAME Available Available FRC.DOUT Available Available I2C0.SCL Available Available Available I2C0.SDA Available Available Available I2C1.SCL Available Available I2C1.SDA Available Available LETIMER0.OUT0 Available LETIMER0.OUT1 Available PRS.ASYNCH0 Available PRS.ASYNCH1 Available PRS.ASYNCH10 Available Available PRS.ASYNCH11 Available Available PRS.ASYNCH2 Available PRS.ASYNCH3 Available PRS.ASYNCH4 Available PRS.ASYNCH5 Available PRS.ASYNCH6 Available Available PRS.ASYNCH7 Available Available PRS.ASYNCH8 Available Available PRS.ASYNCH9 Available Available PRS.SYNCH0 Available Available Available PRS.SYNCH1 Available Available Available PRS.SYNCH2 Available Available Available PRS.SYNCH3 Available Available Available MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Pin Definitions silabs.com | Building a more connected world. Rev. 1.2 | 24

Peripheral.Resource PORT PA PC PD TIMER0.CC0 Available Available Available TIMER0.CC1 Available Available Available TIMER0.CC2 Available Available Available TIMER0.CDTI0 Available Available Available TIMER0.CDTI1 Available Available Available TIMER0.CDTI2 Available Available Available TIMER1.CC0 Available Available Available TIMER1.CC1 Available Available Available TIMER1.CC2 Available Available Available TIMER1.CDTI0 Available Available Available TIMER1.CDTI1 Available Available Available TIMER1.CDTI2 Available Available Available TIMER2.CC0 Available TIMER2.CC1 Available TIMER2.CC2 Available TIMER2.CDTI0 Available TIMER2.CDTI1 Available TIMER2.CDTI2 Available TIMER3.CC0 Available Available TIMER3.CC1 Available Available TIMER3.CC2 Available Available TIMER3.CDTI0 Available Available TIMER3.CDTI1 Available Available TIMER3.CDTI2 Available Available USART0.CLK Available Available Available USART0.CS Available Available Available USART0.CTS Available Available Available USART0.RTS Available Available Available USART0.RX Available Available Available USART0.TX Available Available Available USART1.CLK Available USART1.CS Available USART1.CTS Available USART1.RTS Available USART1.RX Available USART1.TX Available MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Pin Definitions silabs.com | Building a more connected world. Rev. 1.2 | 25

Peripheral.Resource PORT PA PC PD USART2.CLK Available Available USART2.CS Available Available USART2.CTS Available Available USART2.RTS Available Available USART2.RX Available Available USART2.TX Available Available MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Pin Definitions silabs.com | Building a more connected world. Rev. 1.2 | 26

  1. Design Guidelines

7.1 Module Placement

The MGM210L should be placed at the edge of the end-application PCB as seen below. The copper clearance area under the antenna must be void of traces or components to prevent parasitic loading or undesired coupling of signals or noise to the antenna. The width of the GND pour on the end-application PCB should match at least the width of the antenna (e.g. 12.5 mm or greater) to have negligible effect on antenna performance. 12.5 mm 5.0 mm Figure 7.1. Inverted-F Antenna Clearance MGM210L modules do not support the use of an external, alternative antenna. The U.FL connector land pattern on the top layer of the module should not be used, populated or tampered with. Figure 7.2 Horizontal Mounting on page 27 illustrates the placement recommended when mounting the module horizontally to an end- application PCB. It also shows examples of layout cases that will result in severe RF performance degradation for the module. Figure 7.2. Horizontal Mounting Vertical mounting provides mechanical design flexibility that could be advantageous for certain applications. Figure 7.3 Vertical Mount- ing on page 28 illustrates the placement recommended when mounting the module vertically to an end-application PCB. It also shows layout examples that will result in severe RF performance degradation for the module. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Design Guidelines silabs.com | Building a more connected world. Rev. 1.2 | 27

Notice that vertical mounting limits the number of pins available to interact with the module to six (VDD, GND and four GPIOs) which may be suitable for specific use cases only (e.g. to generate PWM outputs for LED control). The trade offs of vertical mounting should be carefully considered prior to choosing such arrangement. 5.0 mm Figure 7.3. Vertical Mounting

7.2 Antenna Optimization

Due to the nature of PCB trace antennas, the MGM210L is sensitive to the thickness of the application PCB on which it is mounted, as well as to any plastics, metal or dielectric materials in close proximity to the antenna. The layout guide shown in Figure 7.2 Horizontal Mounting on page 27 is optimal for an application board thickness of 0.8 mm. For cases where the application board is of a thickness different than the optimal, the impedance and performance of the antenna may be experimentally adjusted by 1. Cutting out the end-application PCB's FR4 material that is under the antenna, or by 2. Adjusting the separation between the lower side of the antenna and the edge of the application board's GND plane underneath the module Impedance and performance optimization can be verified by measuring RSSI or radiated output power until either is maximized.

7.3 Reset

The MGM210L can be reset by pulling the RESET line low, by the internal watchdog timer, or by software command. All three methods are applicable when the module is mounted horizontally on a given end-application board and, hence, all module pins are accessible. When mounted vertically, however, only the second and third methods apply. The reset state does not provide power saving functionality and it is not recommended as a means to conserve power.

7.4 Debug

See AN958: Debugging and Programming Interfaces for Custom Designs. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Design Guidelines silabs.com | Building a more connected world. Rev. 1.2 | 28

The MGM210L supports hardware debugging via 4-pin JTAG or 2-pin serial-wire debug (SWD) interfaces. It is recommended to expose the debug pins in your own hardware design for firmware update and debug purposes. The table below lists the required pins for JTAG and SWD debug interfacing, which are also presented in 6.2 Alternate Pin Functions. If JTAG interfacing is enabled, the module must be power cycled to return to a SWD debug configuration if necessary. Table 7.1. Debug Pins Pin Name Pin Number JTAG Signal SWD Signal Comments PA04 4 TDI N/A This pin is disabled after reset. Once enabled the pin has a built-in pull-up. PA03 3 TDO N/A This pin is disabled after reset. PA02 2 TMS SWDIO Pin is enabled after reset and has a built-in pull-up. PA01 1 TCK SWCLK Pin is enabled after reset and has a built-in pull-down.

7.5 Packet Trace Interface (PTI)

The MGM210L integrates a true PHY-level packet trace interface (PTI) peripheral that can capture packets non-intrusively to monitor and log device and network traffic without burdening processing resources in the module's SoC. The PTI generates two output signals that can serve as a powerful debugging tool, especially in conjunction with other hardware and software development tools available from Silicon Labs. The PTI_DATA and PTI_SYNC signals can be accessed through any GPIO on ports C and D (see FRC.DOUT and FRC.DFRAME peripheral resources in Table 6.4 DBUS Routing on page 24). MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Design Guidelines silabs.com | Building a more connected world. Rev. 1.2 | 29

  1. Package Specifications

8.1 Package Outline

12.5 mm 4.5 mm 5.0 mm 12.0 mm 1.0 mm 2.5 mm 13.0 mm 11.0 mm 11.5 mm 3.0 mm 2.5 mm 9.5 mm 1.35 mm 22.5 mm 0.9 mm (±0.2) (±0.1) (±0.1) (±0.1) (±0.2) (±0.1) (±0.1) (±0.1) (±0.1) (±0.1) 0.9 mm 2.25 mm(±0.2) 10.18 mm(±0.1) 15.50 mm(±0.2) (±0.1) Figure 8.1. Top and Side Views Figure 8.2. Bottom View NOTE: Solder paste thickness adds 0.1 ± 0.05 mm to overall module height MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Package Specifications silabs.com | Building a more connected world. Rev. 1.2 | 30

8.2 PCB Land Pattern

11.10 mm 1.71 mm 1.60 mm 3.30 mm 1.30 mm 1.90 mm 1.71 mm origo o 5.00 mm 1.40 mm 1.40 mm (2.65, 6.45) Figure 8.3. Recommended Module PCB Land Pattern Table 8.1. Pad Sizing and Location Pad Number X Coordinate Y Coordinate Pad Dimensions 1 0.5 9.78 1.1 x 1.6 6 0.5 1.23 1.1 x 1.6 7 2.23 0.5 1.1 x 1.6 12 10.78 0.5 1.1 x 1.6 13 14.67 2.25 1.3 x 3.3 18 14.67 11.75 1.3 x 3.3 Note: 1. All dimensions in mm unless otherwise stated. 2. X and Y coordinates are specified relative to origo at indicated package corner in the figure above. point is recommended to prevent the possibility of a short circuit. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Package Specifications silabs.com | Building a more connected world. Rev. 1.2 | 31

8.3 Marking

The figure below shows the module markings engraved on the RF shield Figure 8.4. MGM210L Top Marking Mark Description The package marking consists of:

  • MGM210Lxxxxxxx - Part number designation
  • Model: MGM210L22F - Model number designation
  • QR Code: YYWWMMABCDE
  • YY – Last two digits of the assembly year.
  • WW – Two-digit workweek when the device was assembled.
  • MMABCDE – Silicon Labs unit code
  • YYWWTTTTTT
  • YY – Last two digits of the assembly year.
  • WW – Two-digit workweek when the device was assembled.
  • TTTTTT – Manufacturing trace code. The first letter is the device revision.
  • Certification marks such as the CE logo, FCC and IC IDs, etc. will be engraved on the grayed out area or printed on the back side of the module, according to regulatory body requirements. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Package Specifications silabs.com | Building a more connected world. Rev. 1.2 | 32
  1. Soldering Recommendations It is recommended that final PCB assembly of the MGM210L follows the industry standard as identified by the Institute for Printed Cir- cuits (IPC). This product is assembled in compliance with the J-STD-001 requirements and the guidelines of IPC-AJ-820. Surface mounting of this product by the end user is recommended to follow IPC-A-610 to meet or exceed class 2 requirements. CLASS 1 General Electronic Products Includes products suitable for applications where the major requirement is function of the completed assembly. CLASS 2 Dedicated Service Electronic Products Includes products where continued performance and extended life is required, and for which uninterrupted service is desired but not critical. Typically the end-use environment would not cause failures. CLASS 3 High Performance/Harsh Environment Electronic Products Includes products where continued high performance or performance-on-demand is critical, equipment downtime cannot be tolerated, end-use environment may be uncommonly harsh, and the equipment must function when required, such as life support or other critical systems. Note: General SMT application notes are provided in the AN1223 document. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Soldering Recommendations silabs.com | Building a more connected world. Rev. 1.2 | 33
  1. Certifications This section details the regulatory certification status of MGM210L modules in various regions. MGM210L modules are also referred to by their formal model name of MGM210L22F. The address for the module manufacturer and certification applicant is: SILICON LABORATORIES FINLAND OY Alberga Business Park, Bertel Jungin aukio 3,

02600 Espoo, Finland

11.1 CE and UKCA

MGM210L modules have been tested against the relevant harmonized/designated standards and are in conformity with the essential requirements and other relevant requirements of the EU's Radio Equipment Directive (RED) (2014/53/EU) and of the UK's Radio Equip- ment Regulations (RER) (S.I. 2017/1206). Every end-product integrating the MGM210L module will need to perform radio EMC tests on the whole assembly according to the ET- SI 301 489-x relevant standard. Furthermore, it is ultimately the responsibility of the manufacturers to ensure the compliance of their end-products as a whole. The spe- cific product assembly is likely to have an impact on the RF radiated characteristics, when compared to the bare module. Hence, manu- facturers should also carefully consider RF radiated testing with the final product assembly to confirm the compliance. The modules are entitled to carry the CE and UKCA compliance marks, and a formal Declaration of Conformity (DoC) is available at the product web page which is reachable starting from https://www.silabs.com/. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 35

11.2 FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. Any changes or modifications not expressly approved by Silicon Labs could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specif- ic operating instructions for satisfying RF exposure compliance. This transmitter meets both portable and mobile requirements in ac- cordance to the limits exposed in the RF Exposure Analysis. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. OEM Responsibilities to comply with FCC Regulations: OEM integrator is responsible for testing their end-product for any additional compliance requirements needed with this module instal- led (for example, digital device emissions, PC peripheral requirements, etc.). Additionally, investigative measurements and spot check- ing are strongly recommended to verify that the full system compliance is maintained when the module is integrated, in accordance to the "Host Product Testing Guidance" in FCC's KDB 996369 D04 Module Integration Guide V01.

  • In the typical case when the integral antenna of the MGM210L is used, a minimum separation distance of 12 mm must be main- tained at all times between the human body and the radiator (antenna) to meet the SAR exemption for portable conditions.
  • The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accord- ance with FCC multi-transmitter product procedures. Important Note: In the event that these conditions cannot be met, then for the FCC authorization to remain valid the final product will have to undergo additional testing to evaluate the RF exposure, and a permissive change will have to be applied with the help of the customer's own Telecommunication Certification Body. End Product Labeling The variants of MGM210L Modules are labeled with their own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: "Contains Transmitter Module FCC ID: QOQMGM210L" Or "Contains FCC ID: QOQMGM210L" The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Class B Device Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular in- stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 36

11.3 ISED Canada

This radio transmitter (IC: 5123A-MGM210L) has been approved by Industry Canada to operate with the embedded antenna. Any other antenna types are strictly prohibited for use with this device. This device complies with Industry Canada’s license-exempt RSS standards. Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device RF Exposure Statement Exception from routine SAR evaluation limits are given in RSS-102 Issue 5. The module meets the given requirements when the minimum separation distance to human body is 20 mm. RF exposure or SAR evaluation is not required when the separation distance is same or more than stated above. If the separation dis- tance is less than stated above the OEM integrator is responsible for evaluating the SAR. OEM Responsibilities to comply with IC Regulations The module has been certified for integration into products only by OEM integrators under the following conditions:

  • The antenna must be installed such that a minimum separation distance as stated above is maintained between the radiator (anten- na) and all persons at all times.
  • The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still respon- sible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the ISEDC authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integra- tor will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate ISEDC authorization. End Product Labeling The MGM210L module is labeled with its own IC ID. If the IC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains Transmitter Module IC: 5123A-MGM210L ” or “Contains IC: 5123A-MGM210L” The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 37

ISEDC (Français) Industrie Canada a approuvé l’utilisation de cet émetteur radio (IC: 5123A-MGM210L) en conjonction avec l'antenne intégrée. L’utilisa- tion de tout autre type d’antenne avec ce composant est proscrite. Ce composant est conforme aux normes RSS, exonérées de licence d'Industrie Canada. Son mode de fonctionnement est soumis aux deux conditions suivantes: 1. Ce composant ne doit pas générer d’interférences. 2. Ce composant doit pouvoir est soumis à tout type de perturbation y compris celle pouvant nuire à son bon fonctionnement. Déclaration d'exposition RF L'exception tirée des limites courantes d'évaluation SAR est donnée dans le document RSS-102 Issue 5. Le module répondent aux exigences requises lorsque la distance minimale de séparation avec le corps humain est de 20 mm. La déclaration d’exposition RF ou l'évaluation SAR n'est pas nécessaire lorsque la distance de séparation est identique ou supérieure à celle indiquée ci-dessus. Si la distance de séparation est inférieure à celle mentionnées plus haut, il incombe à l'intégrateur OEM de procédé à une évaluation SAR. Responsabilités des OEM pour une mise en conformité avec le Règlement du Circuit Intégré Le module a été approuvé pour l'intégration dans des produits finaux exclusivement réalisés par des OEM sous les conditions sui- vantes:

  • L'antenne doit être installée de sorte qu'une distance de séparation minimale indiquée ci-dessus soit maintenue entre le radiateur (antenne) et toutes les personnes avoisinante, ce à tout moment.
  • Le module émetteur ne doit pas être localisé ou fonctionner avec une autre antenne ou un autre transmetteur que celle indiquée plus haut. Tant que les deux conditions ci-dessus sont respectées, il n’est pas nécessaire de tester ce transmetteur de façon plus poussée. Ce- pendant, il incombe à l’intégrateur OEM de s’assurer de la bonne conformité du produit fini avec les autres normes auxquelles il pour- rait être soumis de fait de l’utilisation de ce module (par exemple, les émissions des périphériques numériques, les exigences de pé- riphériques PC, etc.). REMARQUE IMPORTANTE Ans le cas où ces conditions ne peuvent être satisfaites (pour certaines configurations ou co-implantation avec un autre émetteur), l'au- torisation ISEDC n'est plus considérée comme valide et le numéro d’identification ID IC ne peut pas être apposé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera responsable de la réévaluation du produit final (y compris le transmetteur) et de l'ob- tention d'une autorisation ISEDC distincte. Étiquetage des produits finis Les modules MGM210L sont étiquetés avec leur propre ID IC. Si l'ID IC n'est pas visible lorsque le module est intégré au sein d'un autre produit, cet autre produit dans lequel le module est installé devra porter une étiquette faisant apparaitre les référence du module intégré. Dans un tel cas, sur le produit final doit se trouver une étiquette aisément lisible sur laquelle figurent les informations suivantes: “Contient le module transmetteur: 5123A-MGM210L ” or “Contient le circuit: 5123A-MGM210L” L'intégrateur OEM doit être conscient qu’il ne doit pas fournir, dans le manuel d’utilisation, d'informations relatives à la façon d'installer ou de d’enlever ce module RF ainsi que sur la procédure à suivre pour modifier les paramètres liés à la radio.

11.4 Australia (ACMA)

The MGM210L22F is compliant to RCM requirements in Australia and New Zealand and it is labeled with the RCM mark. The formal DoC is available at https://www.silabs.com/.

11.5 Dominican Republic (INDOTEL)

The MGM210L22F has INDOTEL type approval in the Dominican Republic. The formal type approval certificate is available at https:// www.silabs.com/. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 38

11.6 Hong Kong (OFCA)

The MGM210L has approval in Hong Kong. The formal type approval certificate is available at https://www.silabs.com/.

11.7 Israel (MOC)

MGM210L22F modules have wireless type approval from the Ministry of Communication (MOC) in the State of Israel. Confirmation of Compliance is based on statement 55-07826. The formal certificate can be accessed through https://www.silabs.com/. Prior to March 16 of 2021, Confirmation of Compliance was based on statement 51-68584.

11.8 Jordan (TRC)

MGM210L22F modules have type approval from the Telecommunications Regulatory Commission (TRC) in Jordan. Their approval number is TRC/SS/2019/231. The formal certificate can be accessed through https://www.silabs.com/.

11.9 Kuwait (CITRA)

MGM210L22F modules have type approval from the Communication and Information Technology Regulatory Authority (CITRA) in Ku- wait. The formal certificate can be accessed through https://www.silabs.com/.

11.10 Serbia (RATEL)

The MGM210L has type approval in Serbia. The formal type approval certificate is available at https://www.silabs.com/.

11.11 Singapore (IMDA)

The MGM210L has been registered with the Info-communications Media Development Authority under regulation 20(6) of the Telecom- munications (Dealers) Regulations (Cap 323, Rg 6) (the "Dealers Regulations") and approved for sale in Singapore. The registration number is N1436-19.

11.12 Bahrain (BTRA)

The MGM210L22F is compliant to IGA requirements in the Kingdom of Bahrain. The formal IGA Approval Certificate is available at https://www.silabs.com/.

11.13 China (SRRC)

The MGM210L22F conforms to SRRC provisions in China with RTE Type Approval Certificate CMIIT ID: 2019DJ13179. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 39

11.14 Egypt (NTRA)

The MGM210L22F is compliant to NTRA requirements in Egypt and is labeled with the CE mark. The formal NTRA certificate is availa- ble at https://www.silabs.com/.

11.15 Japan (MIC)

The MGM210L22F is certified in Japan with number 203-JN1039. It is the end product manufacturer's responsibility to ensure that the module is configured to meet the limits documented in the formal certification test report available at https://www.silabs.com/. The maximum TX power allowed for regulatory compliance in Japan is +9.5 dBm. Since September 1, 2014 it is allowed (and highly recommended) that a manufacturer who integrates a radio module in their host equipment can place the certification mark and certification number (the same marking/number as depicted on the label of the radio module) on the outside of the host equipment. The certification mark and certification number must be placed close to the text in the Japanese language which is provided below. This change in the Radio Law has been made in order to enable users of the combination of host and radio module to verify if they are actually using a radio device which is approved for use in Japan. Certification Text to be Placed on the Outside Surface of the Host Equipment: Translation of the text: “This equipment contains specified radio equipment that has been certified to the Technical Regulation Conformity Certification under the Radio Law.” The "Giteki" marking shown in the figure below must be affixed to an easily noticeable section of the specified radio equipment. Note that additional information may be required if the device is also subject to a telecom approval. Figure 11.1. GITEKI Mark

11.16 South Korea (KC)

The MGM210L22F is certified in South Korea with number R-C-BGT-MGM210L22F. It is the end product manufacturer's responsibility to ensure that the module is configured to meet the limits documented in the formal certification test report available at https://www.silabs.com/. The maximum TX power allowed for regulatory compliance in South Korea is +10 dBm.

11.17 Morocco (ANRT)

The MGM210L22F is compliant to ANRT requirements in Morocco with Certificate Number MR 19523 ANRT 2019 and Date of Issue 30/04/2019. The formal ANRT Certificate is available at https://www.silabs.com/. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 40

11.18 Qatar (CRA)

The MGM210L22F is compliant to CRA requirements in Qatar with ictQATAR certification number CRA/SM/2019/R-7905. The formal CRA Certificate of Type Approval is available at https://www.silabs.com/.

11.19 Thailand (NBTC)

The MGM210L is compliant to NTC requirements in Thailand. The formal DoC is available at https://www.silabs.com/.

11.20 Taiwan (NCC)

MGM210L22F modules are certified in Taiwan with NCC certification number CCAJ20LP0B50T1 . The OEM manufacturers are required to mark their end-products with the following example sentence: "This product contains a radio frequency module with certification number CCAJ20LP0B50T1." The platform will also need to be listed in the NCC database of approved radio-equipped devices; consequently, the platform manufac- turer is also supposed to contact the certification house that originally released the full modular approval and apply for the registration of their device under the above certification number (fees might apply.) NCC According to NCC Low Power Radio Wave Radiation Equipment Management Regulations: Article 12 A low-power RF equipment that has passed the type approval shall not change the frequency, increase the power or change the characteristics and functions of the original design without permission. Article 14 The use of low-power RF equipment shall not affect flight safety and interfere with legal communications; if in- terference is found, it shall be immediately deactivated and improved until no interference is found. Legal communication in the preceding paragraph refers to radio communications operating in accordance with the provisions of the Telecommunications Act. Low-power RF equipment must withstand interference from legitimate communications or radiological, radiated electrical equipment for industrial, scientific, and medical applications.

11.21 United Arab Emirates (TRA)

The MGM210L22F has Telecom Equipment Type Approval from the Telecommunications Regulatory Authority (TRA) of the United Arab Emirates (UAE). Autorization number: ER78843/20. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 41

11.22 Oman (OTRA)

The MGM210L22F has Telecommunication Equipment Type Approval from the Telecommunications Regulatory Authority (TRA) of the Sultanate of Oman. Approval Number: R/9854/20.

11.23 Saudi Arabia (CITC)

The MGM210L22F conforms to the requirements of the Communications and Information Technology Commission (CITC) of Saudi Arabia. Conformity Certificate No: TA 2020-831.

11.24 Mexico (IFT)

MGM210L22F modules comply with the requirements of the Instituto Federal de Telecomunicaciones (IFT) and are certified in Mexico with number RCPSIMG20-2343. La operación de este equipo está sujeta a las siguientes dos condiciones: 1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. Este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada

11.25 Bluetooth Qualification

The MGM210L modules came at launch with a pre-qualified Bluetooth Low Energy RF-PHY Tested Component having Declaration ID of D043475 and QDID of 129390, and having a listing date of 2019-04-02. Due to expiry, the Tested Component was renewed on 2022-03-29 with a new Declaration ID of D059595 and QDID of 185220. Because the validity set by the SIG for Tested Components is currently of 3 years, during the product lifetime Silicon Labs will renew this Component as it expires, whenever applicable. Renewed Tested Components will come with new DIDs and QDIDs, and these will be then referred to in end-product listings. Such new DIDs and QDIDs can be discovered starting from the original ones. This module’s RF-PHY Tested Component should be combined with the latest Wireless Gecko Link Layer and Host pre-qualified Com- ponents by Silicon Labs, when in the process of qualifying an end-product embedding the MGM210L via the SIG’s Launch Studio. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet Certifications silabs.com | Building a more connected world. Rev. 1.2 | 42

  1. Revision History Revision 1.2 December, 2022
  • Updated supported Bluetooth version from 5.1 to 5.3
  • Updated Bluetooth Qualification information. Revision 1.1 September, 2021
  • Changed number of 16-bit Timer/Counter modules to 3 in 1. Features .
  • Updated TX frequency range in Table 4.5 RF Transmitter General Characteristics for the 2.4 GHz Band on page 11 to specify limits for Zigbee and BLE
  • Removed footnote and clarified test conditions for Input low voltage and Input high voltage specifications in Table 4.14 GPIO Pins on page 18.
  • Added RESETn low time to ensure pin reset (T_RESET) specification to Table 4.14 GPIO Pins on page 18.
  • Updated figures in 8.3 Marking with new placement of YYWWTTTTTT
  • Added 11.20 Taiwan (NCC)
  • Added 11.21 United Arab Emirates (TRA)
  • Added 11.22 Oman (OTRA)
  • Added 11.23 Saudi Arabia (CITC)
  • Added 11.24 Mexico (IFT)
  • Added 11.25 Bluetooth Qualification
  • Updated 11.1 CE and UKCA
  • Updated 11.8 Jordan (TRC)
  • Updated 11.9 Kuwait (CITRA) Revision 1.0 January, 2020
  • Corrected LETIMER's lowest power mode in front page block diagram from EM2 to EM3
  • Resolved remaining TBD entries in Section 4.1 Electrical Characteristics
  • Changed "3.3V" net label in Figure 5.1 MGM210L Application Schematic on page 21 to "VDD", pin U1-12 to DNC and direction of some interconnection labels; also added note on module placement and pinout
  • Updated Note 1, added Note 3, changed pin 12 from "GND" to "DNC" and corrected descriptions for pins 1-4 to "GPIO/Debug" and pins 7, 8 to "GPIO" in Table 6.1 MGM210L Lighting Module Pin Definitions on page 22
  • Updated text for 6.2 Alternate Pin Functions
  • Added text on U.FL land pattern and vertical mounting in Section 7.1 Module Placement
  • Updated text for Section 7.2 Antenna Optimization
  • Added 7.3 Reset, 7.4 Debug, and 7.5 Packet Trace Interface (PTI)
  • Renamed section 8.1 Dimensions as 8.1 Package Outline
  • Renamed Fig 8.1 Module Dimensions as Figure 8.1 Top and Side Views on page 30
  • Added missing outline dimensions and tolerances to Figure 8.1 Top and Side Views on page 30
  • Added Figure 8.2 Bottom View on page 30 and note on impact of solder paste on overall module height
  • Updated Figure 8.2 Bottom View on page 30 and Figure 8.3 Recommended Module PCB Land Pattern on page 31 to show location of bottom layer VDD test point
  • Updated Section rocco (ANRT), 11.18 Qatar (CRA), 11.19 Thailand (NBTC) MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet

Revision History

silabs.com | Building a more connected world. Rev. 1.2 | 43

Revision 0.5.1 September, 2019

  • Updated Ordering Information with "210LA" OPNs
  • Updated Package Specifications with corresponding "210LA" top mark figures Revision 0.5 August, 2019
  • Initial Production Release.
  • Updated Features with latest values, certifications, security, etc
  • Updated Ordering Information with OPNs for Reel packaging
  • Added System Overview
  • Updated Electrical Specifications with latest values
  • Updated Tables 6.2 - 6.4 in Pin Definitions
  • Updated wording and figures in Design Guidelines
  • Updated figures in Package Specifications and added Marking section
  • Added Tape and Reel dimensions
  • Updated list of regions/countries in Certifications
  • General wording, spelling, and grammar fixes. Revision 0.2 July, 2019
  • Updated typical specification values to reflect module measurements.
  • Wording, spelling, and grammar fixes. Revision 0.1 April, 2019
  • Initial Release. MGM210L Wireless Gecko Multi-Protocol Lighting Module Data Sheet

silabs.com | Building a more connected world. Rev. 1.2 | 44

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701 USA www.silabs.com IoT Portfolio www.silabs.com/IoT SW/HW www.silabs.com/simplicity Quality www.silabs.com/quality Support & Community www.silabs.com/community Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software imple - menters using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and “Typical” parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance of the product. Silicon Labs shall have no liability for the consequences of use of the infor - mation supplied in this document. This document does not imply or expressly grant any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required or Life Support Systems without the specific written consent of Silicon Labs. A “Life Support System” is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications. Note: This content may contain offensive terminology that is now obsolete. Silicon Labs is replacing these terms with inclusive language wherever possible. For more information, visit www.silabs.com/about-us/inclusive-lexicon-project Trademark Information Silicon Laboratories Inc. ®, Silicon Laboratories ®, Silicon Labs ®, SiLabs ® and the Silicon Labs logo ®, Bluegiga ®, Bluegiga Logo ®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, “the world’s most energy friendly microcontrollers”, Redpine Signals ®, WiSeConnect , n-Link, ThreadArch ®, EZLink®, EZRadio®, EZRadioPRO ®, Gecko®, Gecko OS, Gecko OS Studio, Precision32 ®, Simplicity Studio ®, Telegesis, the Telegesis Logo ®, USBXpress ® , Zentri, the Zentri logo and Zentri DMS, Z-Wave ®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders.