E40HX1K-CB132

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 52

Technical content

FPGA-DS-02029-3.5 September 2018

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 2 FPGA-DS-02029-3.5

Contents

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 4 FPGA-DS-02029-3.5 Tables

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 5 Acronyms in This Document A list of acronyms used in this document. Acronym Definition DFF D-style Flip-Flop DSP Digital Signal Processor EBR Embedded Block RAM HFOSC High Frequency Oscillator I2C Inter-Integrated Circuit LFOSC Low Frequency Oscillator LUT Look Up Table LVCMOS Low-Voltage Complementary Metal Oxide Semiconductor NVCM Non Volatile Configuration Memory PFU Programmable Functional Unit PLB Programmable Logic Blocks PLL Phase Locked Loops SPI Serial Peripheral Interface WLCSP Wafer Level Chip Scale Packaging

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 6 FPGA-DS-02029-3.5 1. General Description The iCE40™ LP/HX family of ultra-low power, non-volatile FPGAs has five devices with densities ranging from 384 to 7,680 Look-Up Tables (LUTs). In addition to LUT-based, low- cost programmable logic, these devices feature Embedded Block RAM (EBR), Non-volatile Configuration Memory (NVCM) and Phase Locked Loops (PLLs). These features allow the devices to be used in low-cost, high-volume consumer and system applications. Select packages offer High-Current drivers that are ideal to drive three white LEDs, or one RGB LED. The iCE40 LP/HX devices are fabricated on a 40 nm CMOS low power process. The device architecture has several features such as programmable low-swing differential I/Os and the ability to turn off on-chip PLLs dynamically. These features help manage static and dynamic power consumption, resulting in low static power for all members of the family. The iCE40 LP/HX devices are available in two versions – ultra low power (LP) and high performance (HX) devices. The iCE40 LP/HX FPGAs are available in a broad range of advanced halogen-free packages ranging from the space saving 1.40 mm x 1.48 mm WLCSP to the PCB-friendly 20 mm x 20 mm TQFP. Table 2.1 shows the LUT densities, package and I/O options, along with other key parameters. The iCE40 LP/HX devices offer enhanced I/O features such as pull-up resistors. Pull-up features are controllable on a per-pin basis. The iCE40 LP/HX devices also provide flexible, reliable and secure configuration from on-chip NVCM. These devices can also configure themselves from external SPI Flash or be configured by an external master such as a CPU. Lattice provides a variety of design tools that allow complex designs to be efficiently implemented using the iCE40 LP/HX family of devices. Popular logic synthesis tools provide synthesis library support for iCE40 LP/HX. Lattice design tools use the synthesis tool output along with the user-specified preferences and constraints to place and route the design in the iCE40 LP/HX device. These tools extract the timing from the routing and back-annotate it into the design for timing verification. Lattice provides many pre-engineered IP (Intellectual Property) modules, including a number of reference designs, licensed free of charge, optimized for the iCE40 LP/HX FPGA family. By using these configurable soft core IP cores as standardized blocks, users are free to concentrate on the unique aspects of their design, increasing their productivity. 1.1. Features  Flexible Logic Architecture  Five devices with 384 to 7,680 LUT4s and 10 to 206 I/Os  Ultra-low Power Devices  Advanced 40 nm low power process  As low as 21 µA standby power  Programmable low swing differential I/Os  Embedded and Distributed Memory  Up to 128 kb sysMEM™ Embedded Block RAM  Pre-Engineered Source Synchronous I/O  DDR registers in I/O cells  High Current LED Drivers  Three High Current Drivers used for three different LEDs or one RGB LED  High Performance, Flexible I/O Buffer  Programmable sysI/O™ buffer supports wide range of interfaces:  LVCMOS 3.3/2.5/1.8  LVDS25E, subLVDS  Schmitt trigger inputs, to 200 mV typical hysteresis  Programmable pull-up mode  Flexible On-Chip Clocking  Eight low skew global signal resources  Up to two analog PLLs per device  Flexible Device Configuration  SRAM is configured through:  Standard SPI Interface  Internal Nonvolatile Configuration Memory (NVCM)  Broad Range of Package Options  WLCSP , QFN, VQFP , TQFP , ucBGA, caBGA, and csBGA package options  Small footprint package options  As small as 1.40 mm x 1.48 mm  Advanced halogen-free packaging

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 7 2. Product Family Table 2.1 lists device information and packages of the iCE40 LP/HX family. Table 2.1. iCE40 LP/HX Family Selection Guide Part Number LP384 LP640 LP1K LP4K LP8K HX1K HX4K HX8K Logic Cells (LUT + Flip-Flop) 384 640 1,280 3,520 7,680 1,280 3,520 7,680 RAM4K Memory Blocks 0 8 16 20 32 16 20 32 RAM4K RAM bits 0 32K 64K 80K 128K 64K 80K 128K Phase-Locked Loops (PLLs) 0 0 11 22 22 11 2 2 Maximum Programmable I/O Pins 63 25 95 167 178 95 95 206 Maximum Differential Input Pairs 8 3 12 20 23 11 12 26 High Current LED Drivers 0 3 3 0 0 0 0 0

16 WLCSP

32 QFN

84 QFN

(7 mm x 7 mm, 0.5 mm)

100 VQFP

(14 mm x 14 mm, 0.5 mm) 121 ucBGA (5 mm x 5 mm, 0.4 mm) 121 csBGA (6 mm x 6 mm, 0.5 mm) 121 caBGA (9 mm x 9 mm, 0.8 mm) 132 csBGA (8 mm x 8 mm, 0.5 mm)

144 TQFP

(20 mm x 20 mm, 0.5 mm) 225 ucBGA (7 mm x 7 mm, 0.4 mm) 256-ball caBGA (14 mm x 14 mm, 0.8 mm) Notes: 1. No PLL available on the 16 WLCSP, 36 ucBGA, 81 csBGA, 84 QFN, and 100 VQFP packages. 2. Only one PLL available on the 81 ucBGA package. 3. High Current I/Os only available on the 16 WLCSP package.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 8 FPGA-DS-02029-3.5 3. Architecture 3.1. Architecture Overview The iCE40 LP/HX family architecture contains an array of Programmable Logic Blocks (PLB), sysCLOCK™ PLLs, Nonvolatile Programmable Configuration Memory (NVCM) and blocks of sysMEM Embedded Block RAM (EBR) surrounded by Programmable I/O (PIO). Figure 3.1 shows the block diagram of the iCE40LP/HX1K device. Programmable Logic Block (PLB) I/O Bank 0 I/O Bank 3 Programmable Interconnect Programmable Interconnect Programmable Interconnect I/O Bank 1 I/O Bank 2 NVCM Flip-flop with Enable and Reset Controls Non-volatile Configuration Memory (NVCM) Phase-Locked Loop Carry Logic 4-Input Look-up Table (LUT4)

8 Logic Cells = Programmable Logic Block

Figure 3.1. iCE40LP/HX1K Device, Top View The logic blocks, Programmable Logic Blocks (PLB) and sysMEM EBR blocks, are arranged in a two-dimensional grid with rows and columns. Each column has either logic blocks or EBR blocks. The PIO cells are located at the periphery of the device, arranged in banks. The PLB contains the building blocks for logic, arithmetic, and register functions. The PIOs utilize a flexible I/O buffer referred to as a sysI/O buffer that supports operation with a variety of interface standards. The blocks are connected with many vertical and horizontal routing channel resources. The place and route software tool automatically allocates these routing resources. In the iCE40 LP/HX family, there are up to four independent sysI/O banks. Note on some packages VCCIO banks are tied together. There are different types of I/O buffers on the different banks. Refer to the details in later sections of this

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 9 document. The sysMEM EBRs are large 4 kbit, dedicated fast memory blocks. These blocks can be configured as RAM, ROM or FIFO. The iCE40 LP/HX architecture also provides up to two sysCLOCK Phase Locked Loop (PLL) blocks. The PLLs have multiply, divide, and phase shifting capabilities that are used to manage the frequency and phase relationships of the clocks. Every device in the family has a SPI port that supports programming and configuration of the device. The iCE40 LP/HX includes on-chip, Nonvolatile Configuration Memory (NVCM). 3.1.1. PLB Blocks The core of the iCE40 LP/HX device consists of Programmable Logic Blocks (PLB) which can be programmed to perform logic and arithmetic functions. Each PLB consists of eight interconnected Logic Cells (LC) as shown in Figure 3.2. Each LC contains one LUT and one register.

8 Logic Cells (LCs)

Figure 3.2. PLB Block Diagram Logic Cells Each Logic Cell includes three primary logic elements shown in Figure 3.2.  A four-input Look-Up Table (LUT) builds any combinational logic function, of any complexity, requiring up to four inputs. Similarly, the LUT4 element behaves as a 16 x 1 Read-Only Memory (ROM). Combine and cascade multiple LUT4s to create wider logic functions.  A D-style Flip-Flop (DFF), with an optional clock-enable and reset control input, builds sequential logic functions. Each DFF also connects to a global reset signal that is automatically asserted immediately following device configuration.  Carry Logic boosts the logic efficiency and performance of arithmetic functions, including adders, subtracters, comparators, binary counters and some wide, cascaded logic functions. Table 3.1 lists the logic cell signals.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 10 FPGA-DS-02029-3.5 Table 3.1. Logic Cell Signal Descriptions Function Type Signal Name Description Input Data signal I0, I1, I2, I3 Inputs to LUT4 Input Control signal Enable Clock enable shared by all LCs in the PLB Input Control signal Set/Reset* Asynchronous or synchronous local set/reset shared by all LCs in the PLB. Input Control signal Clock Clock one of the eight Global Buffers, or from the general-purpose interconnects fabric shared by all LCs in the PLB. Input Inter-PLB signal FCIN Fast carry in Output Data signals O LUT4 or registered output Output Inter-PFU signal FCOUT Fast carry out *Note: If Set/Reset is not used, then the flip-flop is never set/reset, except when cleared immediately after configuration. 3.1.2. Routing There are many resources provided in the iCE40 LP/HX devices to route signals individually with related control signals. The routing resources consist of switching circuitry, buffers, and metal interconnect (routing) segments. The inter-PLB connections are made with three different types of routing resources: Adjacent (spans two PLBs), x4 (spans five PLBs) and x12 (spans thirteen PLBs). The Adjacent, x4, and x12 connections provide fast and efficient connections in the diagonal, horizontal and vertical directions. The design tool takes the output of the synthesis tool and places and routes the design. 3.1.3. Clock/Control Distribution Network Each iCE40 LP/HX device has eight global inputs, two pins on each side of the device. Note that not all GBINs are available in all packages. These global inputs can be used as high fanout nets, clock, reset or enable signals. The dedicated global pins are identified as GBIN[7:0] and the global buffers are identified as-GBUF[7:0]. These eight inputs may be used as general purpose I/O if they are not used to drive the clock nets. Global buffer GBUF7 in I/O Bank 3 also provides an optional direct LVDS25 or subLVDS differential clock input. Table 3.2 lists the connections between a specific global buffer and the inputs on a PLB. All global buffers optionally connect to the PLB CLK input. Any four of the eight global buffers can drive logic inputs to a PLB. Even-numbered global buffers optionally drive the Set/Reset input to a PLB. Similarly, odd-numbered buffers optionally drive the PLB clock- enable input. Table 3.2. Global Buffer (GBUF) Connections to Programmable Logic Blocks Global Buffer LUT Inputs Clock Reset Clock Enable GBUF0 Yes, any 4 of 8 GBUF Inputs Yes Yes — GBUF1 Yes — Yes GBUF2 Yes Yes — GBUF3 Yes — Yes GBUF4 Yes Yes — GBUF5 Yes — Yes GBUF6 Yes Yes — GBUF7 Yes — Yes The maximum frequency for the global buffers are listed in the External Switching Characteristics tables in this document.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 11 3.1.3.1. Global Hi-Z Control The global high-impedance control signal, GHIZ, connects to all I/O pins on the iCE40 LP/HX device. This GHIZ signal is automatically asserted throughout the configuration process, forcing all user I/O pins into their high-impedance state. 3.1.3.2. Global Reset Control The global reset control signal connects to all PLB and PIO flip-flops on the iCE40 LP/HX device. The global reset signal is automatically asserted throughout the configuration process, forcing all flip-flops to their defined wake-up state. For PLB flip-flops, the wake-up state is always reset, regardless of the PLB flip-flop primitive used in the application. 3.1.4. sysCLOCK Phase Locked Loops (PLLs) The sysCLOCK PLLs provide the ability to synthesize clock frequencies. The iCE40 LP/HX devices have one sysCLOCK PLL. REFERENCECLK is the reference frequency input to the PLL and its source can come from an external I/O pin, the internal Oscillator Generators from internal routing. EXTFEEDBACK is the feedback signal to the PLL which can come from internal routing or an external I/O pin. The feedback divider is used to multiply the reference frequency and thus synthesize a higher frequency clock output. The PLLOUT output has an output divider, thus allowing the PLL to generate different frequencies for each output. The output divider can have a value from 1 to 64 (in increments of 2X). The PLLOUT outputs can all be used to drive the iCE40 LP/HX global clock network directly or general purpose routing resources can be used. The LOCK signal is asserted when the PLL determines it has achieved lock and de-asserted if a loss of lock is detected. A block diagram of the PLL is shown in Figure 3.3. The timing of the device registers can be optimized by programming a phase shift into the PLLOUT output clock which will advance or delay the output clock with reference to the REFERENCECLK clock. This phase shift can be either programmed during configuration or can be adjusted dynamically. In dynamic mode, the PLL may lose lock after a phase adjustment on the output used as the feedback source and not relock until the tLOCK parameter has been satisfied. There is an additional feature in the iCE40 LP/HX PLL. There are two FPGA controlled inputs, SCLK and SDI, that allows the user logic to serially shift in data thru SDI, clocked by SCLK clock. The data shifted in would change the configuration settings of the PLL. This feature allows the PLL to be time multiplexed for different functions, with different clock rates. After the data is shifted in, you would simply pulse the RESET input of the PLL block, and the PLL will re-lock with the new settings. For more details, refer to iCE40 sysCLOCK PLL Design and Usage Guide (TN1251). Input Divider DIVR Low-Pass Filter Voltage Controlled Oscillator (VCO) VCO Divider DIVQ Feedback Divider DIVF RANGE Phase Detector Feedback_Path Fine Delay Adjustment Feedback Phase Shifter LATCHINPUT VALUE REFERENCE CLK DYNAMICDELAY[7:0] BYPASS RESET EXTFEE DBACK PLLOUTCORE PLLOUTGLOBAL LOCK BYPASS Low Pow er mode SIMPLE EXTERNAL VCC PLLGNDPLL Fine Delay Adjustment Output Port SCLK SDI Figure 3.3. PLL Diagram Table 3.3 provides signal descriptions of the PLL block.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 12 FPGA-DS-02029-3.5 Table 3.3. PLL Signal Descriptions Signal Name Direction Description REFERENCECLK Input Input reference clock BYPASS Input The BYPASS control selects which clock signal connects to the PLLOUT output. 0 – PLL generated signal 1 – REFERENCECLK EXTFEEDBACK Input External feedback input to PLL. Enabled when the FEEDBACK_PATH attribute is set to EXTERNAL. DYNAMICDELAY[7:0] Input Fine delay adjustment control inputs. Enabled when DELAY_ADJUSTMENT_MODE is set to DYNAMIC. LATCHINPUTVALUE Input When enabled, puts the PLL into low-power mode; PLL output is held static at the last input clock value. Set ENABLE ICEGATE_PORTA and PORTB to 1 to enable. PLLOUTGLOBAL Output Output from the Phase-Locked Loop (PLL). Drives a global clock network on the FPGA. The port has optimal connections to global clock buffers GBUF4 and GBUF5. PLLOUTCORE Output Output clock generated by the PLL, drives regular FPGA routing. The frequency generated on this output is the same as the frequency of the clock signal generated on the PLLOUTLGOBAL port. LOCK Output When High, indicates that the PLL output is phase aligned or locked to the input reference clock. RESET Input Active low reset. SCLK Input Input, Serial Clock used for re-programming PLL settings. SDI Input Input, Serial Data used for re-programming PLL settings. 3.1.5. sysMEM Embedded Block RAM Memory Larger iCE40 LP/HX device includes multiple high-speed synchronous sysMEM Embedded Block RAMs (EBRs), each 4 kbit in size. This memory can be used for a wide variety of purposes including data buffering and FIFO. 3.1.5.1. sysMEM Memory Block The sysMEM block can implement single port, pseudo dual port, or FIFO memories with programmable logic resources. Each block can be used in a variety of depths and widths as listed in Table 3.4.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 14 FPGA-DS-02029-3.5 Table 3.5 lists the EBR signals. Table 3.5. EBR Signal Descriptions Signal Name Direction Description WDATA[15:0] Input Write Data input. MASK[15:0] Input Masks write operations for individual data bit-lines. 0 – Write bit 1 – Do not write bit WADDR[7:0] Input Write Address input. Selects one of 256 possible RAM locations. WE Input Write Enable input. WCLKE Input Write Clock Enable input. WCLK Input Write Clock input. Default rising-edge, but with falling-edge option. RDATA[15:0] Output Read Data output. RADDR[7:0] Input Read Address input. Selects one of 256 possible RAM locations. RE Input Read Enable input. RCLKE Input Read Clock Enable input. RCLK Input Read Clock input. Default rising-edge, but with falling-edge option. For further information on the sysMEM EBR block, refer to Memory Usage Guide for iCE40 Devices (TN1250). 3.1.6. sysI/O Buffer Banks iCE40 LP/HX devices have up to four I/O banks with independent VCCIO rails with an additional configuration bank VCC_SPI for the SPI I/Os. Programmable I/O (PIO) The programmable logic associated with an I/O is called a PIO. The individual PIOs are connected to their respective sysI/O buffers and pads. The PIOs are placed on the top and bottom of the devices.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 16 FPGA-DS-02029-3.5 (1,0) (1,0) (1,0) (1,0) Pad Pad CLOCK_ENABLE OUTPUT_ENABLE OUTPUT_ENABLE OUTPUT_CLK INPUT_CLK LATCH_INPUT_VALUE LATCH_INPUT_VALUE D_IN_1 D_IN_0 D_OUT_1 D_OUT_0 D_IN_1 D_IN_0 D_OUT_1 D_OUT_0 PIO Pair = Statically defined by configuration program. Figure 3.6. iCE I/O Register Block Diagram Table 3.6. PIO Signal List Pin Name I/O Type Description OUTPUT_CLK Input Output register clock CLOCK_ENABLE Input Clock enable INPUT_CLK Input Input register clock OUTPUT_ENABLE Input Output enable D_OUT_0/1 Input Data from the core D_IN_0/1 Output Data to the core LATCH_INPUT_VALUE Input Latches/holds the Input Value

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 17 3.1.7. sysI/O Buffer Each I/O is associated with a flexible buffer referred to as a sysI/O buffer. These buffers are arranged around the periphery of the device in groups referred to as banks. The sysI/O buffers allow users to implement a wide variety of standards that are found in today’s systems including LVCMOS and LVDS25. High Current LED Drivers combine three sysI/O buffers together. This allows for programmable drive strength. This also allows for high current drivers that are ideal to drive three white LEDs, or one RGB LED. Each bank is capable of supporting multiple I/O standards including single-ended LVCMOS buffers and differential LVDS25E output buffers. Bank 3 additionally supports differential LVDS25 input buffers. Each sysI/O bank has its own dedicated power supply. Typical I/O Behavior During Power-up The internal power-on-reset (POR) signal is deactivated when VCC, VCCIO_2, VPP_2V5, and VCC_SPI have reached the level defined in Table 4.4. After the POR signal is deactivated, the FPGA core logic becomes active. It is your responsibility to ensure that all VCCIO banks are active with valid input logic levels to properly control the output logic states of all the I/O banks that are critical to the application. The default configuration of the I/O pins in a device prior to configuration is tri-stated with a weak pull-up to VCCIO. The I/O pins will maintain the pre-configuration state until VCC and VCCIO (for I/O banks containing configuration I/Os) have reached levels, at which time the I/Os will take on the software user- configured settings only after a proper download/configuration. Unused I/Os are automatically blocked and the pull-up termination is disabled. Supported Standards The iCE40 LP/HX sysI/O buffer supports both single-ended input/output standards, and used as differential configurable options for bus maintenance (weak pull-up or none). Table 3.7 and Table 3.8 show the I/O standards (together with their supply and reference voltages) supported by the iCE40 LP/HX devices. Table 3.7. Supported Input Standards I/O Standard VCCIO (Typical) 3.3 V 2.5 V 1.8 V Single-Ended Interfaces LVCMOS33 Yes — — LVCMOS25 — Yes — LVCMOS18 — — Yes Differential Interfaces LVDS25* — Yes — SubLVDS* — — Yes *Note: Bank 3 only. Table 3.8. Supported Output Standards I/O Standard VCCIO (Typical) Single-Ended Interfaces LVCMOS33 3.3 V LVCMOS25 2.5 V LVCMOS18 1.8 V Differential Interfaces LVDS25* — SubLVDS* — *Note: These interfaces can be emulated with external resistors in all devices.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 18 FPGA-DS-02029-3.5 3.1.8. Non-Volatile Configuration Memory All iCE40 LP/HX devices provide a Non-Volatile Configuration Memory (NVCM) block which can be used to configure the device. For more information on the NVCM, refer to iCE40 Programming and Configuration (FPGA-TN-02001). 3.1.9. Power On Reset iCE40 LP/HX devices have power-on reset circuitry to monitor VCC, VCCIO_2, VPP_2V5, and VCC_SPI voltage levels during power-up and operation. At power-up, the POR circuitry monitors VCC, VCCIO_2, VPP_2V5, and VCC_SPI (controls configuration) voltage levels. It then triggers download from the on-chip NVCM or external Flash memory after reaching the power-up levels specified in the Power-On-Reset Voltage table in the DC and Switching Characteristics section of this data sheet. Before and during configuration, the I/Os are held in tri-state. I/Os are released to user functionality once the device has finished configuration. 3.2. Programming and Configuration This section describes the programming and configuration of the iCE40 LP/HX family. Device Programming The NVCM memory can be programmed through the SPI port. Device Configuration There are various ways to configure the Configuration RAM (CRAM) including:  Internal NVCM Download  From an SPI Flash (Master SPI mode)  System microprocessor to drive a Serial Slave SPI port (SSPI mode) The image to configure the CRAM can be selected by the user on power up (Cold Boot) or once powered up (Warm Boot). For more details on configuring the iCE40 LP/HX device, refer to iCE40 Programming and Configuration (FPGA-TN- 02001). 3.2.1. Power Saving Options iCE40 LP/HX devices are available in two options for maximum flexibility: LP and HX devices. The LP devices have ultra low static and dynamic power consumption. HX devices are designed to provide high performance. Both the LP and the HX devices operate at 1.2 V VCC. iCE40 LP/HX devices feature iCEGate and PLL low power mode to allow users to meet the static and dynamic power requirements of their applications. While these features are available in both device types, these features are mainly intended for use with iCE40 LP devices to manage power consumption. Table 3.9. Power Saving Features Description Device Subsystem Feature Description PLL When LATCHINPUTVALUE is enabled, puts the PLL into low-power mode; PLL output held static at last input clock value. iCEGate To save power, the optional iCEGate latch can selectively freeze the state of individual, non-registered inputs within an I/O bank. Registered inputs are effectively frozen by their associated clock or clock- enable control.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 19 4. DC and Switching Characteristics 4.1. Absolute Maximum Ratings Table 4.1. Absolute Maximum Ratings* Parameter Min Max Unit Supply Voltage VCC –0.5 1.42 V Output Supply Voltage VCCIO –0.5 3.60 V NVCM Supply Voltage VPP_2V5 –0.5 3.60 V PLL Supply Voltage VCCPLL –0.5 1.42 V I/O Tri-state Voltage Applied –0.5 3.60 V Dedicated Input Voltage Applied –0.5 3.60 V Storage Temperature (Ambient) –65 150 °C Junction Temperature (TJ) –55 125 °C *Notes:  Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.  Compliance with the Thermal Management document is required.  All voltages referenced to GND.  I/Os can support a 200 mV Overshoot above the Recommended Operating Conditions VCCIO (Max) and -200 mV Undershoot below VIL (Min). Overshoot and Undershoot is permitted for 25% duty cycle but must not exceed 1.6 ns. 4.2. Recommended Operating Conditions Table 4.2. Recommended Operating Conditions1 Symbol Parameter Min Max Unit VCC 1 Core Supply Voltage 1.14 1.26 V VPP_2V5 VPP_2V5 NVCM Programming and Operating Supply Voltage Slave SPI Configuration 1.71 3.46 V Master SPI Configuration 2.30 3.46 V Configuration from NVCM 2.30 3.46 V NVCM Programming 2.30 3.00 V VPP_FAST4 Optional fast NVCM programming supply. Leave unconnected. N/A N/A V VCCPLL5,6 PLL Supply Voltage 1.14 1.26 V VCCIO1,2,3 I/O Driver Supply Voltage VCCIO0-3 1.71 3.46 V VCC_SPI 1.71 3.46 V tJIND Junction Temperature, Industrial Operation –40 100 °C tPROG Junction Temperature NVCM Programming 10.00 30.00 °C Notes: 1. Like power supplies must be tied together. For example, if VCCIO and VCC_SPI are both the same voltage, they must also be the same supply. 2. See recommended voltages by I/O standard in subsequent table. 3. VCCIO pins of unused I/O banks should be connected to the VCC power supply on boards. 4. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications, except CM36 and CM49 packages MUST have the VPP_FAST ball connected to VCCIO_0 ball externally. 5. No PLL available on the iCE40LP384 and iCE40LP640 device. 6. VCCPLL is tied to VCC internally in packages without PLL pins.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 20 FPGA-DS-02029-3.5 4.3. Power Supply Ramp Rates Table 4.3. Power Supply Ramp Rates* Symbol Parameter Min Max Unit tRAMP Power supply ramp rates for all power supplies All configuration modes. No power supply sequencing. 0.40 10 V/ms Configuring from Slave SPI. No power supply sequencing, 0.01 10 V/ms Configuring from NVCM. VCC and VPP_2V5 to be powered 0.25 ms before VCC_SPI. 0.01 10 V/ms Configuring from MSPI. VCC and VPP_SPI to be powered 0.25 ms before VPP_2V5. 0.01 10 V/ms Notes:  Assumes monotonic ramp rates.  iCE40LP384 requires VCC to be greater than 0.7 V when VCCIO and VCC_SPI are above GND. 4.4. Power-On-Reset Voltage Levels Table 4.4. Power-On-Reset Voltage Levels* Symbol Device Parameter Min Max Unit VPORUP iCE40LP384 Power-On-Reset ramp-up trip point (band gap based circuit monitoring VCC, VCCIO_2, VCC_SPI and VPP_2V5) VCC 0.67 0.99 V VCCIO_2 0.70 1.59 V VCC_SPI 0.70 1.59 V VPP_2V5 0.70 1.59 V iCE40LP640, iCE40LP/HX1K, iCE40LP/HX4K, iCE40LP/HX8K Power-On-Reset ramp-up trip point (band gap based circuit monitoring VCC, VCCIO_2, VCC_SPI and VPP_2V5) VCC 0.55 0.75 V VCCIO_2 0.86 1.29 V VCC_SPI 0.86 1.29 V VPP_2V5 0.86 1.33 V VPORDN iCE40LP384 Power-On-Reset ramp-down trip point (band gap based circuit monitoring VCC, VCCIO_2, VCC_SPI and VPP_2V5) VCC — 0.64 V VCCIO_2 — 1.59 V VCC_SPI — 1.59 V VPP_2V5 — 1.59 V iCE40LP640, iCE40LP/HX1K, iCE40LP/HX4K, iCE40LP/HX8K Power-On-Reset ramp-down trip point (band gap based circuit monitoring VCC, VCCIO_2, VCC_SPI and VPP_2V5) VCC — 0.75 V VCCIO_2 — 1.29 V VCC_SPI — 1.29 V VPP_2V5 — 1.33 V *Note: These POR trip points are only provided for guidance. Device operation is only characterized for power supply voltages specified under recommended operating conditions. 4.5. ESD Performance Please refer to the iCE40 Product Family Qualification Summary for complete qualification data, including ESD performance.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 21 4.6. DC Electrical Characteristics Over recommended operating conditions. Table 4.5. DC Electrical Characteristics Symbol Parameter Condition Min Typ Max Unit IIL, IIH1, 3, 4, 5, 6, 7 Input or I/O Leakage 0 V < VIN < VCCIO + 0.2 V — — ±10 µA C16, 7 I/O Capacitance2 VCCIO = 3.3 V, 2.5 V, 1.8 V VCC = Typ, VIO = 0 to VCCIO + 0.2 V — 6 — pf C26, 7 Global Input Buffer Capacitance2 VCCIO = 3.3 V, 2.5 V, 1.8 V VCC = Typ, VIO = 0 to VCCIO + 0.2 V — 6 — pf VHYST Input Hysteresis VCCIO = 1.8 V, 2.5 V, 3.3 V — 200 — mV IPU6, 7 Internal PIO Pull-up VCCIO = 1.8 V, 0 ≤ VIN ≤ 0.65 * VCCIO −3 — −31 µA VCCIO = 2.5 V, 0 ≤ VIN ≤ 0.65 * VCCIO −8 — −72 µA VCCIO = 3.3 V, 0 ≤ VIN ≤ 0.65 * VCCIO −11 — −128 µA Notes: 1. Input or I/O leakage current is measured with the pin configured as an input or as an I/O with the output driver tri-stated. It is not measured with the output driver active. Internal pull-up resistors are disabled. 2. TJ 25 oC, f = 1.0 MHz. 3. Refer to VIL and VIH in the sysI/O Single-Ended DC Electrical Characteristics table. 4. Only applies to I/Os in the SPI bank following configuration. 5. Some products are clamped to a diode when VIN is larger than VCCIO. 6. High current I/Os has three sysI/O buffers connected together. 7. The iCE40LP640 and iCE40LP1K SWG16 package has CDONE and a sysI/O buffer are connected together. 4.7. Static Supply Current – LP Devices Table 4.6. Supply Current– LP Devices1, 2, 3, 4 Symbol Parameter Device Typ VCC4 Unit ICC Core Power Supply iCE40LP384 21 µA iCE40LP640 100 µA iCE40LP1K 100 µA iCE40LP4K 250 µA iCE40LP8K 250 µA ICCPLL5, 6 PLL Power Supply All devices 0.5 µA IPP_2V5 NVCM Power Supply All devices 1.0 µA ICCIO, ICC_SPI Bank Power Supply4 VCCIO = 2.5 V All devices 3.5 µA Notes: 1. Assumes blank pattern with the following characteristics: all outputs are tri-stated, all inputs are configured as LVCMOS and held at VCCIO or GND, on-chip PLL is off. For more detail with your specific design, use the Power Calculator tool. Power specified with master SPI configuration mode. Other modes may be up to 25% higher. 2. Frequency = 0 MHz. 3. TJ = 25 °C, power supplies at nominal voltage. 4. Does not include pull-up. 5. No PLL available on the iCE40LP384 and iCE40LP640 device. 6. VCCPLL is tied to VCC internally in packages without PLL pins.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 22 FPGA-DS-02029-3.5 4.8. Static Supply Current – HX Devices Table 4.7. Supply Current– HX Devices1, 2, 3, 4 Symbol Parameter Device Typ VCC4 Unit ICC Core Power Supply iCE40HX1K 296 µA iCE40HX4K 1140 µA iCE40HX8K 1140 µA ICCPLL5 PLL Power Supply All devices 0.5 µA IPP_2V5 NVCM Power Supply All devices 1.0 µA ICCIO, ICC_SPI Bank Power Supply4 VCCIO = 2.5 V All devices 3.5 µA Notes: 1. Assumes blank pattern with the following characteristics: all outputs are tri-stated, all inputs are configured as LVCMOS and held at VCCIO or GND, on-chip PLL is off. For more detail with your specific design, use the Power Calculator tool. Power specified with master SPI configuration mode. Other modes may be up to 25% higher. 2. Frequency = 0 MHz. 3. TJ = 25 °C, power supplies at nominal voltage. 4. Does not include pull-up. 5. VCCPLL is tied to VCC internally in packages without PLL pins. 4.9. Programming NVCM Supply Current – LP Devices Table 4.8. Programming NVCM Supply Current – LP Devices1, 2, 3, 4 Symbol Parameter Device Typ VCC5 Unit ICC Core Power Supply iCE40LP384 60 µA iCE40LP640 120 µA iCE40LP1K 120 µA iCE40LP4K 350 µA iCE40LP8K 350 µA All devices 0.5 µA ICCPLL6, 7 PLL Power Supply All devices 2.5 mA IPP_2V5 NVCM Power Supply All devices 3.5 mA ICCIO , ICC_SPI Bank Power Supply4 iCE40LP384 60 µA Notes: 1. Assumes all inputs are held at VCCIO or GND and all outputs are tri-stated. 2. Typical user pattern. 3. SPI programming is at 8 MHz. 4. TJ = 25 °C, power supplies at nominal voltage. 6. No PLL available on the iCE40LP384 and iCE40LP640 devices. 7. VCCPLL is tied to VCC internally in packages without PLLs pins. 8. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications, except CM36 and CM49 packages MUST have the VPP_FAST ball connected to VCCIO_0 ball externally.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 23 4.10. Programming NVCM Supply Current – HX Devices Table 4.9. Programming NVCM Supply Current – HX Devices1, 2, 3, 4 Symbol Parameter Device Typ. VCC5 Units ICC Core Power Supply iCE40HX1K 278 µA iCE40HX4K 1174 µA iCE40HX8K 1174 µA ICCPLL6, 7 PLL Power Supply All devices 0.5 µA IPP_2V5 NVCM Power Supply All devices 2.5 mA ICCIO7, ICC_SPI Bank Power Supply5 All devices 3.5 mA Notes: 1. Assumes all inputs are held at VCCIO or GND and all outputs are tri-stated. 2. Typical user pattern. 3. SPI programming is at 8 MHz. 4. TJ = 25 °C, power supplies at nominal voltage. 6. VCCPLL is tied to VCC internally in packages without PLL pins. 7. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications. 4.11. Peak Startup Supply Current – LP Devices Table 4.10. Peak Startup Supply Current – LP Devices Symbol Parameter Device Max Units ICCPEAK Core Power Supply iCE40LP384 7.7 mA iCE40LP640 6.4 mA iCE40LP1K 6.4 mA iCE40LP4K 15.7 mA iCE40LP8K 15.7 mA ICCPLLPEAK1, 2, 4 PLL Power Supply iCE40LP1K 1.5 mA iCE40LP640 1.5 mA iCE40LP4K 8.0 mA iCE40LP8K 8.0 mA IPP_2V5PEAK NVCM Power Supply iCE40LP384 3.0 mA iCE40LP640 7.7 mA iCE40LP1K 7.7 mA iCE40LP4K 4.2 mA iCE40LP8K 4.2 mA IPP_FASTPEAK3 NVCM Programming Supply iCE40LP384 5.7 mA iCE40LP640 8.1 mA iCE40LP1K 8.1 mA ICCIOPEAK5, ICC_SPIPEAK Bank Power Supply iCE40LP384 8.4 mA iCE40LP640 3.3 mA iCE40LP1K 3.3 mA iCE40LP4K 8.2 mA iCE40LP8K 8.2 mA Notes: 1. No PLL available on the iCE40LP384 and iCE40LP640 device. 2. VCCPLL is tied to VCC internally in packages without PLLs pins. 3. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications, except CM36 and CM49 packages MUST have the VPP_FAST ball connected to VCCIO_0 ball externally. 4. While no PLL is available in the iCE40LP640 the ICCPLLPEAK is additive to ICCPEAK. 5. iCE40LP384 requires VCC to be greater than 0.7 V when VCCIO and VCC_SPI are above GND.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 24 FPGA-DS-02029-3.5 4.12. Peak Startup Supply Current – HX Devices Table 4.11. Peak Startup Supply Current – HX Devices Symbol Parameter Device Max Units ICCPEAK Core Power Supply iCE40HX1K 6.9 mA iCE40HX4K 22.3 mA iCE40HX8K 22.3 mA ICCPLLPEAK* PLL Power Supply iCE40HX1K 1.8 mA iCE40HX4K 6.4 mA iCE40HX8K 6.4 mA IPP_2V5PEAK NVCM Power Supply iCE40HX1K 2.8 mA iCE40HX4K 4.1 mA iCE40HX8K 4.1 mA ICCIOPEAK, ICC_SPIPEAK Bank Power Supply iCE40HX1K 6.8 mA iCE40HX4K 6.8 mA iCE40HX8K 6.8 mA *Note: VCCPLL is tied to VCC internally in packages without PLLs pins. 4.13. sysI/O Recommended Operating Conditions Table 4.12. sysI/O Recommended Operating Conditions Input/Output Standard VCCIO (V) Min. Typ. Max. LVCMOS 3.3 3.14 3.3 3.46 LVCMOS 2.5 2.37 2.5 2.62 LVCMOS 1.8 1.71 1.8 1.89 LVDS25E1, 2 2.37 2.5 2.62 subLVDSE1, 2 1.71 1.8 1.89 Notes: 1. Inputs on-chip. Outputs are implemented with the addition of external resistors. 2. Does not apply to Configuration Bank VCC_SPI. 4.14. sysI/O Single-Ended DC Electrical Characteristics Table 4.13. sysI/O Single-Ended DC Electrical Characteristics Input/Output Standard VIL VIH1 VOL Max. (V) VOH Min. (V) IOL Max. (mA) IOH Max. (mA) Min. (V) Max. (V) Min. (V) Max. (V) 0.4 VCCIO – 0.4 8, 16 , 24 –8, –16 –24 0.2 VCCIO – 0.2 0.1 –0.1 0.4 VCCIO – 0.4 6, 12 , 18 –6, –12 –18 0.2 VCCIO – 0.2 0.1 –0.1 0.4 VCCIO – 0.4 4, 8 , 12 –4, –8 , – 0.2 VCCIO – 0.2 0.1 –0.1 Notes: 1. Some products are clamped to a diode when VIN is larger than VCCIO. 2. Only for High Drive LED outputs.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 25 4.15. sysI/O Differential Electrical Characteristics The LVDS25E/subLVDSE differential output buffers are available on all banks but the LVDS/subLVDS input buffers are only available on Bank 3 of iCE40 LP/HX devices. 4.15.1. LVDS25 Over recommended operating conditions. Table 4.14. LVDS25 Parameter Symbol Parameter Description Test Conditions Min. Typ. Max. Units VINP, VINM Input Voltage VCCIO* = 2.5 0 — 2.5 V VTHD Differential Input Threshold — 250 350 450 mV VCM Input Common Mode Voltage VCCIO* = 2.5 (VCCIO/2) - 0.3 VCCIO/2 (VCCIO/2) + 0.3 V IIN Input Current Power on — — ±10 µA *Note: Typical 4.15.2. subLVDS Over recommended operating conditions. Table 4.15. subLVDS Parameter Symbol Parameter Description Test Conditions Min. Typ. Max. Units VINP, VINM Input Voltage VCCIO* = 2.5 0 — 1.8 V VTHD Differential Input Threshold — 100 150 200 mV VCM Input Common Mode Voltage VCCIO* = 2.5 (VCCIO/2) -

0.25 VCCIO/2 (VCCIO/2) +

0.25 V IIN Input Current Power on — — ±10 µA *Note: Typical

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 26 FPGA-DS-02029-3.5 4.16. LVDS25E Emulation iCE40 LP/HX devices can support LVDSE outputs via emulation on all banks. The output is emulated using complementary LVCMOS outputs in conjunction with resistors across the driver outputs on all devices. The scheme shown in Figure 4.1. LVDS25E Using External Resistors is one possible solution for LVDS25E standard implementation. Resistor values in Figure 4.1. LVDS25E Using External Resistors are industry standard values for 1% resistors. R R R OD OCM VCCIO Differential Output Pair Figure 4.1. LVDS25E Using External Resistors Over recommended operating conditions. Table 4.16. LVDS25E DC Conditions Parameter Description Typ. Units ZOUT Output impedance 20 Ω RS Driver series resistor 150 Ω RP Driver parallel resistor 140 Ω RT Receiver termination 100 Ω VOH Output high voltage 1.43 V VOL Output low voltage 1.07 V VOD Output differential voltage 0.30 V VCM Output common mode voltage 1.25 V ZBACK Back impedance 100.5 Ω IDC DC output current 6.03 mA

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 27 4.17. SubLVDS Emulation The iCE40 LP/HX family supports the differential subLVDS standard. The output standard is emulated using complementary LVCMOS outputs in conjunction with resistors across the driver outputs on all banks of the devices. The subLVDS input standard is supported by the LVDS25 differential input buffer. The scheme shown in Figure 4.2 is one possible solution for subLVDSE output standard implementation. Use LVDS25E mode with suggested resistors for subLVDSE operation. Resistor values in Figure 4.2 are industry standard values for 1% resistors. R R R OD OCM VCCIO Differential Output Pair Figure 4.2. subLVDSE DC Conditions Over recommended operating conditions. Table 4.17. subLVDSE DC Conditions Parameter Description Typ. Units ZOUT Output impedance 20 Ω RS Driver series resistor 270 Ω RP Driver parallel resistor 120 Ω RT Receiver termination 100 Ω VOH Output high voltage 1.43 V VOL Output low voltage 1.07 V VOD Output differential voltage 0.35 V VCM Output common mode voltage 0.9 V ZBACK Back impedance 100.5 Ω IDC DC output current 2.8 mA

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 28 FPGA-DS-02029-3.5 4.18. Typical Building Block Function Performance – LP Devices* 4.18.1. Pin-to-Pin Performance (LVCMOS25) – LP Devices Table 4.18. Pin-to-Pin Performance (LVCMOS25) – LP Devices Function Timing Units Basic Functions 16-bit decoder 11.0 ns 4:1 MUX 12.0 ns 16:1 MUX 13.0 ns 4.18.2. Register-to-Register Performance – LP Devices Table 4.19. Register-to-Register Performance – LP Devices Function Timing Units Basic Functions 16:1 MUX 190 MHz 16-bit adder 160 MHz 16-bit counter 175 MHz Embedded Memory Functions 256 x 16 Pseudo-Dual Port RAM 240 MHz *Notes:  The above timing numbers are generated using the iCECube2 design tool. Exact performance may vary with device and tool version. The tool uses internal parameters that have been characterized but are not tested on every device.  Using a VCC of 1.14 V at Junction Temp 85 °C. 4.19. Typical Building Block Function Performance – HX Devices* 4.19.1. Pin-to-Pin Performance (LVCMOS25) – HX Devices Table 4.20. Pin-to-Pin Performance (LVCMOS25) – HX Devices Function Timing Units Basic Functions 16-bit decoder 10.0 ns 4:1 MUX 9.0 ns 16:1 MUX 9.5 ns

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 29 4.19.2. Register-to-Register Performance – HX Devices Table 4.21. Register-to-Register Performance – HX Devices Function Timing Units Basic Functions 16:1 MUX 305 MHz 16-bit adder 220 MHz 16-bit counter 255 MHz 64-bit counter 105 MHz Embedded Memory Functions 256 x 16 Pseudo-Dual Port RAM 403 MHz Notes:  The above timing numbers are generated using the iCECube2 design tool. Exact performance may vary with device and tool version. The tool uses internal parameters that have been characterized but are not tested on every device.  Using a VCC of 1.14 V at Junction Temp 85 °C. 4.20. Derating Logic Timing Logic timing provided in the following sections of the data sheet and the Lattice design tools are worst case numbers in the operating range. Actual delays may be much faster. Lattice design tools can provide logic timing numbers at a particular temperature and voltage. 4.21. Maximum sysI/O Buffer Performance Table 4.22. Register-to-Register Performance1 I/O Standard Max. Speed Units Inputs LVDS252 400 MHz subLVDS182 400 MHz LVCMOS33 250 MHz LVCMOS25 250 MHz LVCMOS18 250 MHz Outputs LVDS25E 250 MHz subLVDS18E 155 MHz LVCMOS33 250 MHz LVCMOS25 250 MHz LVCMOS18 155 MHz Notes: 1. Measured with a toggling pattern. 2. Supported in Bank 3 only.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 30 FPGA-DS-02029-3.5 4.22. Timing Adders Over recommended operating conditions. Table 4.23. Timing Adders – LP Devices* Input Adjusters LVDS25 LVDS, VCCIO = 2.5 V –0.18 ns subLVDS subLVDS, VCCIO = 1.8 V 0.82 ns LVCMOS33 LVCMOS, VCCIO = 3.3 V 0.18 ns LVCMOS25 LVCMOS, VCCIO = 2.5 V 0.00 ns LVCMOS18 LVCMOS, VCCIO = 1.8 V 0.19 ns Output Adjusters LVDS25E LVDS, Emulated, VCCIO = 2.5 V 0.00 ns subLVDSE subLVDS, Emulated, VCCIO = 1.8 V 1.32 ns LVCMOS33 LVCMOS, VCCIO = 3.3 V –0.12 ns LVCMOS25 LVCMOS, VCCIO = 2.5 V 0.00 ns LVCMOS18 LVCMOS, VCCIO = 1.8 V 1.32 ns *Notes:  Timing adders are relative to LVCMOS25 and characterized but not tested on every device.  LVCMOS timing measured with the load specified in the Switching Test Condition table.  All other standards tested according to the appropriate specifications.  Commercial timing numbers are shown.  Not all I/O standards are supported for all banks. See the Architecture section of this data sheet for details. Over recommended operating conditions. Table 4.24. Timing Adders – HX Devices* Input Adjusters LVDS25 LVDS, VCCIO = 2.5 V 0.13 ns subLVDS subLVDS, VCCIO = 1.8 V 1.03 ns LVCMOS33 LVCMOS, VCCIO = 3.3 V 0.16 ns LVCMOS25 LVCMOS, VCCIO = 2.5 V 0.00 ns LVCMOS18 LVCMOS, VCCIO = 1.8 V 0.23 ns Output Adjusters LVDS25E LVDS, Emulated, VCCIO = 2.5 V 0.00 ns subLVDSE subLVDS, Emulated, VCCIO = 1.8 V 1.76 ns LVCMOS33 LVCMOS, VCCIO = 3.3 V 0.17 ns LVCMOS25 LVCMOS, VCCIO = 2.5 V 0.00 ns LVCMOS18 LVCMOS, VCCIO = 1.8 V 1.76 ns *Notes:  Timing adders are relative to LVCMOS25 and characterized but not tested on every device.  LVCMOS timing measured with the load specified in the Switching Test Condition table.  All other standards tested according to the appropriate specifications.  Commercial timing numbers are shown.  Not all I/O standards are supported for all banks. See the Architecture section of this data sheet for details.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 31 4.23. External Switching Characteristics – LP Devices Over recommended operating conditions. Table 4.25. External Switching Characteristics – LP Devices1, 2 Parameter Description Device Min. Max. Units Clock Global Clocks fMAX_GBUF Frequency for Global Buffer Clock network All iCE40 LP devices — 275 MHz tW_GBUF Clock Pulse Width for Global Buffer All iCE40 LP devices 0.92 — ns tSKEW_GBUF Global Buffer Clock Skew Within a Device iCE40LP384 — 370 ps iCE40LP640 — 230 ps iCE40LP1K — 230 ps iCE40LP4K — 340 ps iCE40LP8K — 340 ps Pin-LUT-Pin Propagation Delay tPD Best case propagation delay through one LUT-4 All iCE40 LP devices — 9.36 ns General I/O Pin Parameters (Using Global Buffer Clock without PLL) tSKEW_IO Data bus skew across a bank of IOs iCE40LP384 — 300 ps iCE40LP640 — 200 ps iCE40LP1K — 200 ps iCE40LP4K — 280 ps iCE40LP8K — 280 ps tCO Clock to Output - PIO Output Register iCE40LP384 — 6.33 ns iCE40LP640 — 5.91 ns iCE40LP1K — 5.91 ns iCE40LP4K — 6.58 ns iCE40LP8K — 6.58 ns tSU Clock to Data Setup - PIO Input Register iCE40LP384 –0.08 — ns iCE40LP640 –0.33 — ns iCE40LP1K –0.33 — ns iCE40LP4K –0.63 — ns iCE40LP8K –0.63 — ns tH Clock to Data Hold - PIO Input Register iCE40LP384 1.99 — ns iCE40LP640 2.81 — ns iCE40LP1K 2.81 — ns iCE40LP4K 3.48 — ns iCE40LP8K 3.48 — ns

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 32 FPGA-DS-02029-3.5 Parameter Description Device Min. Max. Units General I/O Pin Parameters (Using Global Buffer Clock with PLL)3 tCOPLL Clock to Output - PIO Output Register iCE40LP1K — 2.20 ns iCE40LP4K — 2.30 ns iCE40LP8K — 2.30 ns tSUPLL Clock to Data Setup - PIO Input Register iCE40LP1K 5.23 — ns iCE40LP4K 6.13 — ns iCE40LP8K 6.13 — ns tHPLL Clock to Data Hold - PIO Input Register iCE40LP1K –0.90 — ns iCE40LP4K –0.80 — ns iCE40LP8K –0.80 — ns Notes: 1. Exact performance may vary with device and design implementation. Commercial timing numbers are shown at 85 °C and 1.14 V. Other operating conditions can be extracted from the iCECube2 software. 2. General I/O timing numbers based on LVCMOS 2.5, 0 pf load. 3. Supported on devices with a PLL.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 33 4.24. External Switching Characteristics – HX Devices Over recommended operating conditions. Table 4.26. External Switching Characteristics – HX Devices1, 2 Parameter Description Device Min. Max. Units Clock Global Clocks fMAX_GBUF Frequency for Global Buffer Clock network All iCE40 HX devices — 275 MHz tW_GBUF Clock Pulse Width for Global Buffer All iCE40 HX devices 0.88 — ns tSKEW_GBUF Global Buffer Clock Skew Within a Device iCE40HX1K — 727 ps iCE40HX4K — 300 ps iCE40HX8K — 300 ps Pin-LUT-Pin Propagation Delay tPD Best case propagation delay through one LUT-4 All iCE40 HX devices — 7.30 ns General I/O Pin Parameters (Using Global Buffer Clock without PLL) tSKEW_IO Data bus skew across a bank of IOs iCE40HX1K — 696 ps iCE40HX4K — 290 ps iCE40HX8K — 290 ps tCO Clock to Output - PIO Output Register iCE40HX1K — 5.00 ns iCE40HX4K — 5.41 ns iCE40HX8K — 5.41 ns tSU Clock to Data Setup - PIO Input Register iCE40HX1K –0.23 — ns iCE40HX4K –0.43 — ns iCE40HX8K –0.43 — ns tH Clock to Data Hold - PIO Input Register iCE40HX1K 1.92 — ns iCE40HX4K 2.38 — ns iCE40HX8K 2.38 — ns General I/O Pin Parameters (Using Global Buffer Clock with PLL)3 tCOPLL Clock to Output - PIO Output Register iCE40HX1K — 2.96 ns iCE40HX4K — 2.51 ns iCE40HX8K — 2.51 ns tSUPLL Clock to Data Setup - PIO Input Register iCE40HX1K 3.10 — ns iCE40HX4K 4.16 — ns iCE40HX8K 4.16 — ns tHPLL Clock to Data Hold - PIO Input Register iCE40HX1K –0.60 — ns iCE40HX4K –0.53 — ns iCE40HX8K –0.53 — ns Notes: 1. Exact performance may vary with device and design implementation. Commercial timing numbers are shown at 85 °C and 1.14 V. Other operating conditions, including industrial, can be extracted from the iCECube2 software. 2. General I/O timing numbers based on LVCMOS 2.5, 0pf load. 3. Supported on devices with a PLL.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 34 FPGA-DS-02029-3.5 4.25. sysClock PLL Timing Over recommended operating conditions. Table 4.27. sysClock PLL Timing Parameter Descriptions Conditions Min. Max. Units fIN Input Clock Frequency (REFERENCECLK, EXTFEEDBACK) — 10 133 MHz fOUT Output Clock Frequency (PLLOUT) — 16 275 MHz fVCO PLL VCO Frequency — 533 1066 MHz AC Characteristics tDT Output Clock Duty Cycle fOUT < 175 MHz 40 50 %

175 MHz < fOUT < 275

MHz 35 65 "% tPH Output Phase Accuracy — — +/–12 deg tOPJIT1, 5 Output Clock Period Jitter fOUT <= 100 MHz — 450 ps p-p fOUT > 100 MHz — 0.05 UIPP Output Clock Cycle-to-cycle Jitter fOUT <= 100 MHz — 750 ps p-p fOUT > 100 MHz — 0.10 UIPP Output Clock Phase Jitter fPFD <= 25 MHz — 275 ps p-p fPFD > 25 MHz — 0.05 UIPP tW Output Clock Pulse Width At 90% or 10% 1.3 — ns tLOCK2, 3 PLL Lock-in Time — — 50 us tUNLOCK PLL Unlock Time — — 50 ns tIPJIT4 Input Clock Period Jitter fPFD  20 MHz — 1000 ps p-p fPFD < 20 MHz — 0.02 UIPP tFDTAP Fine Delay adjustment, per Tap — 147 195 ps tSTABLE3 LATCHINPUTVALUE LOW to PLL Stable — — 500 ns tSTABLE_PW3 LATCHINPUTVALUE Pulse Width — — 100 ns tRST RESET Pulse Width — 10 — ns tRSTREC RESET Recovery Time — 10 — us tDYNAMIC_WD DYNAMICDELAY Pulse Width — 100 — VCO Cycles tPDBYPASS Propagation delay with the PLL in bypass mode iCE40 LP 1.18 4.68 ns iCE40 HX 1.73 4.07 ns Notes: 1. Period jitter sample is taken over 10,000 samples of the primary PLL output with a clean reference clock. Cycle-to-cycle jitter is taken over 1000 cycles. Phase jitter is taken over 2000 cycles. All values per JESD65B. 2. Output clock is valid after tLOCK for PLL reset and dynamic delay adjustment. 3. At minimum fPFD. As the fPFD increases the time will decrease to approximately 60% the value listed. 4. Maximum limit to prevent PLL unlock from occurring. Does not imply the PLL will operate within the output specifications listed in this table. 5. The jitter values will increase with loading of the PLD fabric and in the presence of SSO noise.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 35 4.26. SPI Master or NVCM Configuration Time Table 4.28. SPI Master or NVCM Configuration Time1, 2 Symbol Parameter Condition Typ. Units tCONFIG POR/CRESET_B to Device I/O Active iCE40LP384 - Low Frequency (Default) 25 ms iCE40LP384 - Medium Frequency 15 ms iCE40LP384 - High Frequency 11 ms iCE40LP640 - Low Frequency (Default) 53 ms iCE40LP640 - Medium Frequency 25 ms iCE40LP640 - High Frequency 13 ms iCE40LP/HX1K - Low Frequency (Default) 53 ms iCE40LP/HX1K - Medium Frequency 25 ms iCE40LP/HX1K - High Frequency 13 ms iCE40LP/HX4K - Low Frequency (Default) 230 ms iCE40LP/HX4K - Medium Frequency 110 ms iCE40LP/HX4K - High Frequency 70 ms iCE40LP/HX8K - Low Frequency (Default) 230 ms iCE40LP/HX8K - Medium Frequency 110 ms iCE40LP/HX8K - High Frequency 70 ms Notes: 1. Assumes sysMEM Block is initialized to an all zero pattern if they are used. 2. The NVCM download time is measured with a fast ramp rate starting from the maximum voltage of POR trip point.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 36 FPGA-DS-02029-3.5 4.27. sysCONFIG Port Timing Specifications Table 4.29. sysCONFIG Port Timing Specifications1 Symbol Parameter Min Typ Max Unit All Configuration Modes tCRESET_B Minimum CRESET_B Low pulse width required to restart configuration, from falling edge to rising edge — 200 — — ns tDONE_IO Number of configuration clock cycles after CDONE goes High before the PIO pins are activated — 49 — — Clock Cycles Slave SPI tCR_SCK Minimum time from a rising edge on CRESET_B until the first SPI write operation, first SPI_SCK. During this time, the iCE40 device is clearing its internal configuration memory. iCE40LP384 600 — — us iCE40LP640, iCE40LP/HX1K 800 — — us iCE40LP/HX4K 1200 — — us iCE40LP/HX8K 1200 — — us tCR_SCK Minimum time from a rising edge on CRESET_B until the first SPI write operation, first SPI_SCK. During this time, the iCE40 LP/HX device is clearing its internal configuration memory. Write 1 — 25 MHz Read iCE40LP384 — 15 — MHz Read iCE40LP640, iCE40LP/HX1K — 15 — MHz Read iCE40LP/HX4K — 15 — MHz Read iCE40LP/HX8K — 15 — MHz tCCLKH CCLK clock pulse width high — 20 — — ns tCCLKL CCLK clock pulse width low — 20 — — ns tSTSU CCLK setup time — 12 — ns tSTH CCLK hold time — 12 — — ns tSTCO CCLK falling edge to valid output — 13 — — ns Master SPI fMCLK MCLK clock frequency Off — 0 — MHz Low Frequency (Default) — 7.5 — MHz Medium Frequency — 24 — MHz High Frequency — 40 — MHz tMCLK CRESET_B high to first MCLK edge iCE40LP384 - Low Frequency (Default) 600 — — us iCE40LP384 - Medium Frequency 600 — — us iCE40LP384 - High Frequency 600 — — us iCE40LP640, iCE40LP/HX1K - Low Frequency (Default) 800 — — us iCE40LP640, iCE40LP/HX1K - Medium Frequency 800 — — us iCE40LP640, iCE40LP/HX1K - High Frequency 800 — — us iCE40LP/HX1K -Low Frequency (Default) 800 — — us iCE40LP/HX1K - Medium Frequency 800 — — us iCE40LP/HX1K - High Frequency 800 — — us iCE40LP/HX4K - Low Frequency (Default) 1200 — — us

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 37 Symbol Parameter Min Typ Max Unit iCE40LP/HX4K - Medium Frequency 1200 — — us iCE40LP/HX4K - high frequency 1200 — — us iCE40LP/HX8K - Low Frequency (Default) 1200 — — us iCE40LP/HX8K - Medium Frequency 1200 — — us iCE40LP/HX8K - High Frequency 1200 — — us Notes: 1. Does not apply for NVCM. 2. Supported only with 1.2 V VCC and at 25 °C. 3. Extended range fMAX Write operations support up to 53 MHz only with 1.2 V VCC and at 25 °C. 4.28. Switching Test Conditions Figure 4.3 shows the output test load that is used for AC testing. The specific values for resistance, capacitance, voltage, and other test conditions are listed in Table 4.30. DUT VT CL Test Point Figure 4.3. Output Test Load, LVCMOS Standards Table 4.30. Test Fixture Required Components, Non-Terminated Interfaces* Test Condition R1 CL Timing Reference VT LVCMOS settings (L ≥ H, H ≥ L) ∞ 0 pF LVCMOS 3.3 = 1.5 V — LVCMOS 2.5 = VCCIO/2 — LVCMOS 1.8 = VCCIO/2 — LVCMOS 3.3 (Z ≥ H) 188 0 pF

1.5 V VOL

LVCMOS 3.3 (Z ≥ L) 1.5 V VOH Other LVCMOS (Z ≥ H) VCCIO/2 VOL Other LVCMOS (Z ≥ L) VCCIO/2 VOH LVCMOS (H ≥ Z) VOH – 0.15 V VOL LVCMOS (L ≥ Z) VOL – 0.15 V VOH *Note: Output test conditions for all other interfaces are determined by the respective standards.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 38 FPGA-DS-02029-3.5 5. Pinout Information 5.1. Signal Descriptions 5.1.1. General Purpose Signal Name I/O Description IO[Bank]_[Row/Column Number][A/B] I/O [Bank] indicates the bank of the device on which the pad is located. [Number] indicates IO number on the device. IO[Bank]_[Row/Column Number][A/B] I/O [Bank] indicates the bank of the device on which the pad is located. [Number] indicates IO number on the device. [A/B] indicates the differential I/O. 'A' = negative input. 'B' = positive input. HCIO[Bank]_[Number] I/O High Current IO. [Bank] indicates the bank of the device on which the pad is located. [Number] indicates IO number. NC — No connect GND — GND – Ground. Dedicated pins. It is recommended that all GNDs are tied together. VCC — VCC – The power supply pins for core logic. Dedicated pins. It is recommended that all VCCs are tied to the same supply. VCCIO_x — VCCIO – The power supply pins for I/O Bank x. Dedicated pins. All VCCIOs located in the same bank are tied to the same supply. 5.1.2. PLL and Global Functions (Used as user-programmable I/O pins when not used for PLL or clock pins) Signal Name I/O Description VCCPLLx — PLL VCC – Power. Dedicated pins. The PLL requires a separate power and ground that is quiet and stable to reduce the output clock jitter of the PLL. GNDPLLx — PLL GND – Ground. Dedicated pins. The sysCLOCK PLL has the DC ground connection made on the FPGA, so the external PLL ground connection (GNDPLL) must NOT be connected to the board’s ground. GBINx — Global pads. Two per side. 5.1.3. Programming and Configuration Signal Name I/O Description CBSEL[0:1] I/O Dual function pins. I/Os when not used as CBSEL. Optional ColdBoot configuration Select input, if ColdBoot mode is enabled. CRESET_B I Configuration Reset, active Low. Dedicated input. No internal pull-up resistor. Either actively drive externally or connect a 10 kΩ pull-up resistor to VCCIO_2. CDONE I/O Configuration Done. Includes a permanent weak pull-up resistor to VCCIO_2. If driving external devices with CDONE output, an external pull- up resistor to VCCIO_2 may be required. Refer to the iCE40 Programming and Configuration (FPGA-TN-02001) for more details. Following device configuration the iCE40LP640 and iCE40LP1K in the SWG16 package CDONE pin can be used as a user output.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 39 Signal Name I/O Description VCC_SPI — SPI interface voltage supply input. Must have a valid voltage even if configuring from NVCM. SPI_SCK I/O Input Configuration Clock for configuring an FPGA in Slave SPI mode. Output Configuration Clock for configuring an FPGA configuration modes. SPI_SS I/O SPI Slave Select. Active Low. Includes an internal weak pull-up resistor to VCC_SPI during configuration. During configuration, the logic level sampled on this pin determines the configuration mode used by the iCE40 LP/HX device. An input when sampled at the start of configuration. An input when in SPI Peripheral configuration mode (SPI_SS = Low). An output when in Master SPI Flash configuration mode. SPI_SI I/O Slave SPI serial data input and master SPI serial data output SPI_SO I/O Slave SPI serial data output and master SPI serial data input VPP_FAST — Optional fast NVCM programming supply. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications, except CM36 and CM49 packages MUST have the VPP_FAST ball connected to VCCIO_0 ball externally. VPP_2V5 — VPP_2V5 NVCM programming and operating supply

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 40 FPGA-DS-02029-3.5 5.2. Pin Information Summary iCE40LP384 iCE40LP640 iCE40LP1K SG32 CM362 CM492 SWG16 SWG16 CM361, CM491, CM81 CB81 QN84 CM121 CB121 General Purpose I/O per Bank Bank 0 6 4 10 3 3 4 10 17 17 17 24 24 Bank 1 5 7 7 0 0 7 7 15 16 17 25 21 Bank 2 0 4 4 1 1 4 4 11 8 11 18 19 Bank 3 6 6 12 2 2 6 10 16 17 18 24 24 Configuration 4 4 4 4 4 4 4 4 4 4 4 4 Total General Purpose Single Ended I/O 21 25 37 10 10 25 35 63 62 67 95 92 High Current Outputs per Bank Bank 0 0 0 0 3 3 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 0 0 0 0 0 Bank 3 0 0 0 0 0 0 0 0 0 0 0 0 Total Current Outputs 0 0 0 3 3 0 0 0 0 0 0 0 Differential Inputs per Bank Bank 0 0 0 0 0 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 0 0 0 0 0 Bank 3 3 3 6 1 1 3 5 8 9 7 12 12 Total Differential Inputs 3 3 6 1 1 3 5 8 9 7 12 12 Dedicated Inputs per Bank Bank 0 0 0 0 0 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 0 0 0 0 0 Bank 2 2 2 2 1 1 2 2 2 2 2 2 2 Bank 3 0 0 0 0 0 0 0 0 0 0 0 0 Configuration 0 0 0 0 0 0 0 0 0 0 0 0 Total Dedicated Inputs 2 2 2 1 1 2 2 2 2 2 2 2 Vccio Pins Bank 0 1 1 1 1 1 1 1 1 1 1 2 1 Bank 1 1 1 1 0 0 0 0 1 1 1 2 1 Bank 2 1 1 1 1 1 1 1 1 1 1 2 1 Bank 3 1 0 0 0 0 0 0 1 1 1 2 2 VCC 1 1 2 1 1 1 2 3 3 4 4 4 VCC_SPI 1 1 1 0 0 1 1 1 1 1 1 1 VPP_2V5 1 1 1 0 0 1 1 1 1 1 1 1 VPP_FAST3 0 0 0 0 0 1 1 1 0 1 1 1 VCCPLL 0 0 0 0 0 0 1 1 0 0 1 1 GND 2 3 3 2 2 3 4 5 8 4 8 11 NC 0 0 0 0 0 0 0 0 0 0 0 3 Total Count of Bonded Pins 32 36 49 16 16 36 49 81 81 84 121 121 Notes: 1. VCCIO0 and VCCIO1 are connected together. 2. VCCIO2 and VCCIO3 are connected together. 3. VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications, except CM36 and CM49 packages MUST have the VPP_FAST ball connected to VCCIO_0 ball externally.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 41 iCE40LP4K iCE40LP8K iCE40HX1K CM81 CM121 CM225 CM81 CM121 CM225 VQ100 CB132 TQ144 General Purpose I/O per Bank Bank 0 17 23 46 17 23 46 19 24 23 Bank 1 15 21 42 15 21 42 19 25 25 Bank 2 9 19 40 9 19 40 12 20 20 Bank 3 18 26 46 18 26 46 18 22 24 Configuration 4 4 4 4 4 4 4 4 4 Total General Purpose Single Ended I/O 63 93 178 63 93 178 72 95 96 High Current Outputs per Bank Bank 0 0 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 0 0 Bank 3 0 0 0 0 0 0 0 0 0 Total Differential Inputs 0 0 0 0 0 0 0 0 0 Differential Inputs per Bank Bank 0 0 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 0 0 Bank 3 9 13 23 9 13 23 9 11 12 Total Differential Inputs 9 13 23 9 13 23 9 11 12 Dedicated Inputs per Bank Bank 0 0 0 0 0 0 0 0 0 0 Bank 1 0 0 1 0 0 1 0 0 0 Bank 2 2 2 2 2 2 2 2 2 2 Bank 3 0 0 0 0 0 0 0 0 0 Configuration 0 0 0 0 0 0 0 0 0 Total Dedicated Inputs 2 2 3 2 2 3 2 2 2 Vccio Pins Bank 0 1 1 3 1 1 3 2 2 2 Bank 1 1 1 3 1 1 3 2 2 2 Bank 2 1 1 3 1 1 3 2 2 2 Bank 3 1 2 4 1 2 4 3 3 2 VCC 3 4 8 3 4 8 4 5 4 VCC_SPI 1 1 1 1 1 1 1 1 1 VPP_2V5 1 1 1 1 1 1 1 1 1 VPP_FAST* 1 1 1 1 1 1 1 1 1 VCCPLL 1 2 2 1 2 2 0 1 1 GND 5 12 18 5 12 18 10 14 10 NC 0 0 0 0 0 0 0 2 19 Total Count of Bonded Pins 81 121 225 81 121 225 100 132 144 *Note: 1VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 42 FPGA-DS-02029-3.5 iCE40HX4K iCE40HX8K BG121 CB132 TQ144 BG121 CB132 CM225 CT256 General Purpose I/O per Bank Bank 0 23 24 27 23 24 46 52 Bank 1 21 25 29 21 25 42 52 Bank 2 19 18 19 19 18 40 46 Bank 3 26 24 28 26 24 46 52 Configuration 4 4 4 4 4 4 4 Total General Purpose Single Ended I/O 93 95 107 93 95 178 206 High Current Outputs per Bank Bank 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 Bank 3 0 0 0 0 0 0 0 Total Differential Inputs 0 0 0 0 0 0 0 Differential Inputs per Bank Bank 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 Bank 2 0 0 0 0 0 0 0 Bank 3 13 12 14 13 12 23 26 Total Differential Inputs 13 12 14 13 12 23 26 Dedicated Inputs per Bank Bank 0 0 0 0 0 0 0 0 Bank 1 0 0 0 0 0 0 0 Bank 2 2 2 2 2 2 2 2 Bank 3 0 0 0 0 0 0 0 Configuration 0 0 0 0 0 0 0 Total Dedicated Inputs 2 2 2 2 2 2 2 Vccio Pins Bank 0 1 2 2 1 2 3 4 Bank 1 1 2 2 1 2 3 4 Bank 2 1 2 2 1 2 3 4 Bank 3 2 3 2 2 3 4 4 VCC 4 5 4 4 5 8 6 VCC_SPI 1 1 1 1 1 1 1 VPP_2V5 1 1 1 1 1 1 1 VPP_FAST* 1 1 1 1 1 1 1 VCCPLL 2 2 2 2 2 2 2 GND 12 15 11 12 15 18 20 NC 0 0 6 0 0 0 0 Total Count of Bonded Pins 121 132 144 121 132 225 256 *Note: VPP_FAST, used only for fast production programming, must be left floating or unconnected in applications.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 44 FPGA-DS-02029-3.5 5.4. Ordering Information iCE40 LP/HX devices have top-side markings as shown below: Industrial iCE40HX8K CM225 Datecode Figure 5.3. High Performance (HX) Devices Note: Markings are abbreviated for small packages. 5.5. Ordering Part Numbers 5.5.1. Ultra Low Power Industrial Grade Devices, Halogen Free (RoHS) Packaging Part Number LUTs Supply Voltage Package Leads Temperature ICE40LP384-CM36 384 1.2 V Halogen-Free ucBGA 36 IND ICE40LP384-CM36TR 384 1.2 V Halogen-Free ucBGA 36 IND ICE40LP384-CM36TR1K 384 1.2 V Halogen-Free ucBGA 36 IND ICE40LP384-CM49 384 1.2 V Halogen-Free ucBGA 49 IND ICE40LP384-CM49TR 384 1.2 V Halogen-Free ucBGA 49 IND ICE40LP384-CM49TR1K 384 1.2 V Halogen-Free ucBGA 49 IND ICE40LP384-SG32 384 1.2 V Halogen-Free QFN 32 IND ICE40LP384-SG32TR 384 1.2 V Halogen-Free QFN 32 IND ICE40LP384-SG32TR1K 384 1.2 V Halogen-Free QFN 32 IND ICE40LP640-SWG16TR 640 1.2 V Halogen-Free WLCSP 16 IND ICE40LP640-SWG16TR50 640 1.2 V Halogen-Free WLCSP 16 IND ICE40LP640-SWG16TR1K 640 1.2 V Halogen-Free WLCSP 16 IND ICE40LP1K-SWG16TR 1280 1.2 V Halogen-Free WLCSP 16 IND ICE40LP1K-SWG16TR50 1280 1.2 V Halogen-Free WLCSP 16 IND ICE40LP1K-SWG16TR1K 1280 1.2 V Halogen-Free WLCSP 16 IND ICE40LP1K-CM36 1280 1.2 V Halogen-Free ucBGA 36 IND ICE40LP1K-CM36TR 1280 1.2 V Halogen-Free ucBGA 36 IND ICE40LP1K-CM36TR1K 1280 1.2 V Halogen-Free ucBGA 36 IND ICE40LP1K-CM49 1280 1.2 V Halogen-Free ucBGA 49 IND ICE40LP1K-CM49TR 1280 1.2 V Halogen-Free ucBGA 49 IND ICE40LP1K-CM49TR1K 1280 1.2 V Halogen-Free ucBGA 49 IND ICE40LP1K-CM81 1280 1.2 V Halogen-Free ucBGA 81 IND ICE40LP1K-CM81TR 1280 1.2 V Halogen-Free ucBGA 81 IND ICE40LP1K-CM81TR1K 1280 1.2 V Halogen-Free ucBGA 81 IND ICE40LP1K-CB81 1280 1.2 V Halogen-Free csBGA 81 IND ICE40LP1K-CB81TR 1280 1.2 V Halogen-Free csBGA 81 IND ICE40LP1K-CB81TR1K 1280 1.2 V Halogen-Free csBGA 81 IND ICE40LP1K-CM121 1280 1.2 V Halogen-Free ucBGA 121 IND

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 45 Part Number LUTs Supply Voltage Package Leads Temperature ICE40LP1K-CM121TR 1280 1.2 V Halogen-Free ucBGA 121 IND ICE40LP1K-CM121TR1K 1280 1.2 V Halogen-Free ucBGA 121 IND ICE40LP1K-CB121 1280 1.2 V Halogen-Free csBGA 121 IND ICE40LP1K-QN84 1280 1.2 V Halogen-Free QFN 84 IND ICE40LP4K-CM81 3520 1.2 V Halogen-Free ucBGA 81 IND ICE40LP4K-CM81TR 3520 1.2 V Halogen-Free ucBGA 81 IND ICE40LP4K-CM81TR1K 3520 1.2 V Halogen-Free ucBGA 81 IND ICE40LP4K-CM121 3520 1.2 V Halogen-Free ucBGA 121 IND ICE40LP4K-CM121TR 3520 1.2 V Halogen-Free ucBGA 121 IND ICE40LP4K-CM121TR1K 3520 1.2 V Halogen-Free ucBGA 121 IND ICE40LP4K-CM225 3520 1.2 V Halogen-Free ucBGA 225 IND ICE40LP8K-CM81 7680 1.2 V Halogen-Free ucBGA 81 IND ICE40LP8K-CM81TR 7680 1.2 V Halogen-Free ucBGA 81 IND ICE40LP8K-CM81TR1K 7680 1.2 V Halogen-Free ucBGA 81 IND ICE40LP8K-CM121 7680 1.2 V Halogen-Free ucBGA 121 IND ICE40LP8K-CM121TR 7680 1.2 V Halogen-Free ucBGA 121 IND ICE40LP8K-CM121TR1K 7680 1.2 V Halogen-Free ucBGA 121 IND ICE40LP8K-CM225 7680 1.2 V Halogen-Free ucBGA 225 IND 5.5.2. High-Performance Industrial Grade Devices, Halogen Free (RoHS) Packaging Part Number LUTs Supply Voltage Package Leads Temperature ICE40HX1K-CB132 1280 1.2 V Halogen-Free csBGA 132 IND ICE40HX1K-VQ100 1280 1.2 V Halogen-Free VQFP 100 IND ICE40HX1K-TQ144 1280 1.2 V Halogen-Free TQFP 144 IND ICE40HX4K-BG121 3520 1.2 V Halogen-Free caBGA 121 IND ICE40HX4K-BG121TR 3520 1.2 V Halogen-Free caBGA 121 IND ICE40HX4K-CB132 3520 1.2 V Halogen-Free csBGA 132 IND ICE40HX4K-TQ144 3520 1.2 V Halogen-Free TQFP 144 IND ICE40HX8K-BG121 7680 1.2 V Halogen-Free caBGA 121 IND ICE40HX8K-BG121TR 7680 1.2 V Halogen-Free caBGA 121 IND ICE40HX8K-CB132 7680 1.2 V Halogen-Free csBGA 132 IND ICE40HX8K-CM225 7680 1.2 V Halogen-Free ucBGA 225 IND ICE40HX8K-CT256 7680 1.2 V Halogen-Free caBGA 256 IND

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 46 FPGA-DS-02029-3.5 Supplemental Information For Further Information A variety of technical documents for the iCE40 LP/HX family are available on the Lattice web site.  iCE40 Programming and Configuration (FPGA-TN-02001)  Memory Usage Guide for iCE40 Devices (TN1250)  iCE40 sysCLOCK PLL Design and Usage Guide (TN1251)  iCE40 Hardware Checklist (TN1252)  Using Differential I/O LVDS Sub-LVDS in iCE40 Devices (TN1253)  PCB Layout Recommendations for BGA Packages (FPGA-TN-02010)  iCE40 LED Driver Usage Guide (TN1288)  iCE40 Pinout Files  Thermal Management  Lattice design tools  IBIS  Package Diagrams  Schematic Symbols

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 47 Technical Support For assistance, submit a technical support case at www.latticesemi.com/techsupport.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 48 FPGA-DS-02029-3.5

Revision History

Revision 3.5, September 2018 Section Change Summary All  Changed document number from DS1040 to FPGA-DS-02029.  Updated document template. Pinout Information Changed signal name from SPI_SS_B to SPI_SS in Signal Descriptions table. Revision 3.4, October 2017 Section Change Summary Pin Information Modified the dedicated inputs for Bank 1 of iCE40HX1K (CB132, TQ144), iCE40HX4K (CB132, TQ144) and iCE40HX8K (CB132, CM225, CT256). Revision 3.3, March 2017 Section Change Summary Introduction Updated Features section. Added 121-ball caBGA package for ICE40 HX4K/8K to Table 1-1, iCE40 LP/HX Family Selection Guide. Architecture Updated PLB Blocks section. Changed “subtracters” to “subtractors” in the Carry Logic description. Updated Clock/Control Distribution Network section. Switched the Clock Enable and the Reset headings in Table 2-2, Global Buffer (GBUF) Connections to Programmable Logic Blocks. Pinout Information Updated Pin Information Summary section. Added BG121information under iCE40HX4K and iCE40HX8K. package under High Performance (HX) Devices. Updated Ordering Information section. Added part numbers for BG121 under High- Performance Industrial Grade Devices, Halogen Free (RoHS) Packaging. Supplemental Information Corrected reference to “Package Diagrams Data Sheet”. Revision 3.2, October 2015 Section Change Summary Introduction Updated Features section. Added footnote to 16 WLCSP Programmable I/O: Max Inputs (LVDS25) in Table 1-1, iCE40 LP/HX Family Selection Guide. DC and Switching Characteristics Updated sysCLOCK PLL Timing section. Changed tDT conditions. Updated Programming NVCM Supply Current – LP Devices section. Changed IPP_2V5 and ICCIO, ICC_SPI units. Revision 3.1, March 2015 Section Change Summary DC and Switching Characteristics Updated sysI/O Single-Ended DC Electrical Characteristics section. Changed LVCMOS 3.3 and

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 49 Revision 3.0, July 2014 Section Change Summary DC and Switching Characteristics Revised and/or added Typ. VCC data in the following sections.  Static Supply Current – LP Devices  Static Supply Current – HX Devices  Programming NVCM Supply Current – LP Devices  Programming NVCM Supply Current – HX Devices In each section table, the footnote indicating Advanced device status was removed. Pinout Information Updated Pin Information Summary section. Added footnote 1 to CM49 under iCE40LP1K. Revision 02.9, April 2014 Section Change Summary Ordering Information Changed “i” to “I” in part number description and ordering part numbers. Added part numbers to the Ultra Low Power Industrial Grade Devices, Halogen Free (RoHS) Packaging table. Revision 02.8, February 2014 Section Change Summary DC and Switching Characteristics Updated Features section.  Corrected standby power units.  Included High Current LED Drivers. Updated Table 1-1, iCE40 LP/HX Family Selection Guide.  Removed LP384 Programmable I/O for 81 ucBGA package. Architecture Updated Supported Standards section. Added information on High Current LED drivers. DC and Switching Characteristics Corrected typos. Added footnote to the Peak Startup Supply Current – LP Devices table. Ordering Information Updated part number description in the Ultra Low Power (LP) Devices section. Added part numbers to the Ultra Low Power Industrial Grade Devices, Halogen Free (RoHS) Packaging table. Revision 02.7, October 2013 Section Change Summary Introduction Updated Features list and iCE40 LP/HX Family Selection Guide table. Architecture Revised iCE40-1K device to iCE40LP/HX1K device. DC and Switching Characteristics Added iCE40LP640 device information. Pinout Information Added iCE40LP640 and iCE40LP1K information. Ordering Information Added iCE40LP640 and iCE40LP1K information. Revision 02.6, September 2013 Section Change Summary DC and Switching Characteristics Updated Absolute Maximum Ratings section. Updated sysCLOCK PLL Timing – Preliminary table. Pinout Information Updated Pin Information Summary table.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 50 FPGA-DS-02029-3.5 Revision 02.5, August 2013 Section Change Summary Introduction Updated the iCE40 LP/HX Family Selection Guide table. DC and Switching Characteristics Updated the following tables:  Absolute Maximum Ratings  Power-On-Reset Voltage Levels  Static Supply Current – LP Devices  Static Supply Current – HX Devices  Programming NVCM Supply Current – LP Devices  Programming NVCM Supply Current – HX Devices  Peak Startup Supply Current – LP Devices  sysI/O Recommended Operating Conditions  Typical Building Block Function Performance – HX Devices  External Switching Characteristics – HX Devices  sysCLOCK PLL Timing – Preliminary  SPI Master or NVCM Configuration Time Pinout Information Updated the Pin Information Summary table. Revision 02.4, July 2013 Section Change Summary Introduction Updated the iCE40 LP/HX Family Selection Guide table. DC and Switching Characteristics Updated the sysCONFIG Port Timing Specifications table. Updated footnote in DC Electrical Characteristics table. GDDR tables removed. Support to be provided in a technical note. Pinout Information Updated the Pin Information Summary table. Ordering Information Updated the top-side markings figure. Updated the Ultra Low Power Industrial Grade Devices, Halogen Free (RoHS) Packaging table. Revision 02.3, May 2013 Section Change Summary DC and Switching Characteristics Added new data from Characterization. Revision 02.2, April 2013 Section Change Summary Introduction Added the LP8K 81 ucBGA. Architecture Corrected typos. DC and Switching Characteristics Corrected typos. Pinout Information Added 7:1 LVDS waveforms. Ordering Information Corrected typos in signal descriptions.

© 2011-2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. FPGA-DS-02029-3.5 51 Revision 02.1, March 2013 Section Change Summary DC and Switching Characteristics Recommended operating conditions added requirement for Master SPI. Updated Recommended Operating Conditions for VPP_2V5. Updated Power-On-Reset Voltage Levels and sequence requirements. Updated Static Supply Current conditions. Changed unit for tSKEW_IO from ns to ps. Updated range of CCLK fMAX. Ordering Information Updated ordering information to include tape and reel part numbers. Revision 02.0, September 2012 Section Change Summary All Merged SiliconBlue iCE40 LP and HX data sheets and updated to Lattice format. Revision 01.31, September 2012 Section Change Summary Introduction Updated Table 1. Revision 01.3, September 2012 Section Change Summary All Production release. — Updated notes on Table 3: Recommended Operating Conditions. — Updated values in Table 4, Table 5, Table 12, Table 13 and Table 17. Revision 01.21, September 2012 Section Change Summary — Updated Figure 3 and Figure 4 to specify iCE40. Revision 01.2, August 2012 Section Change Summary — Updated company name. Revision 01.1, July 2011 Section Change Summary — Moved package specifications to iCE40 pinout Excel files. Updated Table 1 maximum I/Os. Revision 01.01, July 2011 Section Change Summary — Added 640, 1K and 4K to Table 13 configuration times. Updated Table 1 maximum I/Os. Revision 01.0, July 2011 Section Change Summary — Initial release.

7th Floor, 111 SW 5th Avenue Portland, OR 97204, USA T 503.268.8000 www.latticesemi.com