CA3240 SYC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 15

Technical content

Features

  • Dual Version of CA3140
  • Internally Compensated
  • MOSFET Input Stage - Very High Input Impedance (Z IN) 1.5TΩ (Typ) - Very Low Input Current (I I) 10pA (Typ) at ±15V - Wide Common-Mode Input Voltage Range (V ICR): Can Be Swung 0.5V Below Negative Supply Voltage Rail
  • Directly Replaces Industry Type 741 in Most Applications
  • Pb-Free Available (RoHS Compliant)

Applications

  • Ground Referenced Single Amplifiers in Automobile and Portable Instrumentation
  • Sample and Hold Amplifiers
  • Long Duration Timers/Multivibrators (Microseconds- Minutes-Hours)
  • Photocurrent Instrumentation Pinout CA3240, CA3240A (PDIP) TOP VIEW

Ordering Information

TEMP. RANGE (oC) PACKAGE PKG. DWG. # CA3240AE -40 to 85 8 Ld PDIP E8.3 CA3240AEZ (See Note) -40 to 85 8 Ld PDIP (Pb-free) E8.3 CA3240E -40 to 85 8 Ld PDIP E8.3 CA3240EZ (See Note) -40 to 85 8 Ld PDIP (Pb-free) E8.3 Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. A ≈ 10,000 BIAS CIRCUIT CURRENT SOURCES AND REGULATOR A ≈ 1 2mA 4mA 2mA1.6mA 2 µA200µA200µA IN- OUT- 12pF A ≈ 10 PUT PUT

  • Intrusion Alarm System • Active Filters
  • Comparators • Function Generators
  • Instrumentation Amplifiers • Power Supplies OUTPUT (A) INV. INPUT (A) NON-INV. OUTPUT INV. NON-INV. INPUT (A) INPUT (B) INPUT (B) CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2001-2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

Absolute Maximum Ratings Thermal Information Operating Conditions Thermal Resistance (Typical, Note 2) θJA (oC/W) *Pb-free PDIPs can be used for through hole wave solder process- ing only. They are not intended for use in Reflow solder processing applications. CAUTION: Stresses above those listed in “Abs olute Maximum Ratings” may cause permanent dam age to the device. This is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Short circuit may be applied to ground or to either supply. Temperatures and/or supply voltages must be limited to keep dissipation within max- imum rating. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications For Equipment Design, VSUPPLY = ±15V, TA = 25oC, Unless Otherwise Specified PARAMETER SYMBOL CA3240 CA3240A UNITSMIN TYP MAX MIN TYP MAX Input Offset Voltage V IO -51 5- 2 5 m V Input Offset Current I IO - 0.5 30 - 0.5 20 pA Input Current I I - 10 50 - 10 40 pA Large-Signal Voltage Gain (See Figures 12, 27) (Note 3) AOL 20 100 - 20 100 - kV/V 86 100 - 86 100 - dB Common Mode Rejection Ratio (See Figure 17) CMRR - 32 320 - 32 320 µV/V 70 90 - 70 90 - dB Common Mode Input Voltage Range (See Figure24) VICR -15 -15.5 to +12.5 11 -15 -15.5 to +12.5 12 V Power Supply Rejection Ratio (See Figure 19) PSRR (∆VIO/∆V±) - 100 150 - 100 150 µV/V 76 80 - 76 80 - dB Maximum Output Voltage (Note 4) (See Figures 23, 24) VOM+ 12 13 - 12 13 - V Maximum Output Voltage (Note 5) V OM- 0.4 0.13 - 0.4 0.13 - V Total Supply Current (See Figure 15) For Both Amps I+ - 8 12 - 8 12 mA Total Device Dissipation P D - 240 360 - 240 360 mW NOTES: 3. At V O = 26VP-P, +12V, -14V and RL = 2kΩ. 4. At R L = 2kΩ. 5. At V+ = 5V, V- = GND, I SINK = 200µA. Electrical Specifications For Equipment Design, VSUPPLY = ±15V, TA = 25oC, Unless Otherwise Specified PARAMETER SYMBOL TEST CONDITIONS TYPICAL VALUES UNITSCA3240A CA3240 Input Resistance R I 1.5 1.5 T Ω Input Capacitance C I 44 p F Output Resistance R O 60 60 Ω Equivalent Wideband Input Noise Voltage (See Figure 2) eN BW = 140kHz, RS = 1MΩ 48 48 µV CA3240, CA3240A

Equivalent Input Noise Voltage (See Figure 18) eN f = 1kHz, RS = 100Ω 40 40 nV/ √Hz f = 10kHz, RS = 100Ω 12 12 nV/ √Hz Short-Circuit Current to Opposite Supply I OM+S o u r c e 4 0 4 0 m A IOM-S i n k 1 1 1 1 m A Gain Bandwidth Product (See Figures 13, 27) f T 4.5 4.5 MHz Slew Rate (See Figure 14) SR 9 9 V/ µs Transient Response (See Figure 1) t r RL = 2kΩ, CL = 100pF Rise Time 0.08 0.08 µs OS R L = 2kΩ, CL = 100pF Overshoot 10 10 % Settling Time at 10VP-P (See Figure 25) t S AV = +1, RL = 2kΩ, CL = 100pF, Voltage Follower To 1mV 4.5 4.5 µs To 10mV 1.4 1.4 µs Crosstalk (See Figure 22) f = 1kHz 120 120 dB Electrical Specifications For Equipment Design, VSUPPLY = ±15V, TA = 25oC, Unless Otherwise Specified (Continued) PARAMETER SYMBOL TEST CONDITIONS TYPICAL VALUES UNITSCA3240A CA3240 Electrical Specifications For Equipment Design, at VSUPPLY = ±15V, TA = -40 to 85oC, Unless Otherwise Specified PARAMETER SYMBOL TYPICAL VALUES UNITSCA3240A CA3240 Input Offset Voltage |V IO|3 1 0 m V Input Offset Current (Note 8) |I IO|3 2 3 2 p A Input Current (Note 8) I I 640 640 pA Large Signal Voltage Gain (See Figures 12, 27), (Note 6) A OL 63 63 kV/V 96 96 dB Common Mode Rejection Ratio (See Figure 17) CMRR 32 32 µV/V 90 90 dB Common Mode Input Voltage Range (See Figure 24) V ICR -15 to +12.3 -15 to +12.3 V Power Supply Rejection Ratio (See Figure 19) PSRR (∆VIO/∆V±) 150 150 µV/V 76 76 dB Maximum Output Voltage (Note 7) (See Figures 23, 24) V OM+ 12.4 12.4 V VOM- -14.2 -14.2 V Supply Current (See Figure 15) Total For Both Amps I+ 8.4 8.4 mA Total Device Dissipation P D 252 252 mW Temperature Coefficient of Input Offset Voltage ∆VIO/∆T1 5 1 5 µV/oC NOTES: 6. At V O = 26VP-P, +12V, -14V and RL = 2kΩ. 7. At R L = 2kΩ. 8. At T A = 85oC. Electrical Specifications For Equipment Design, at V+ = 5V, V- = 0V, TA = 25oC, Unless Otherwise Specified PARAMETER SYMBOL TYPICAL VALUES UNITSCA3240A CA3240 Input Offset Voltage |V IO|2 5 m V Input Offset Current |I IO|0 . 1 0 . 1 p A Input Current I I 22 p A Input Resistance R IN 11 T Ω Large Signal Voltage Gain (See Figures 12, 27) A OL 100 100 kV/V 100 100 dB CA3240, CA3240A

FIGURE 2. TEST CIRCUIT AMPLIFIER (30dB GAIN) USED FOR WIDEBAND NOISE MEASUREMENT

  1. All resistance values are in ohms.

light level as the source ages. FIGURE 11. DIFFERENTIAL LIGHT DETECTOR

FIGURE 26. INPUT CURRENT vs TEMPERATURE FIGURE 27. OPEN LOOP VOLTAGE GAIN AND PHASE vs