BL9641 BELLING | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
www.belling.com.cn 1 42V Input Standoff Voltage, 0.7A Step-Down Converter BL9641
DESCRIPTION
The BL9641 is a wide input range, high-efficiency, and high frequency DC-to-DC step-down switching regulator, capable of delivering up to 0.7A of output current. With a fixed switching frequency of 660KHz, this current mode PWM controlled converter allows the use of small external components, such as ceramic input and output caps, as well as small inductors.BL9641 also employs a proprietary control scheme that switches the device into a power save mode during light load, thereby extending the range of high efficiency operation. An OVP function protects the IC itself and its downstream system against input voltage surges. With this OVP function, the IC can stand off input voltage as high as 42V, making it an ideal solution for industrial applications such as smart meters as well as automotive applications. In automotive systems, power comes from the battery, with its voltage typically between 9V and 24V. Including cold crank and double battery jump-starts, the minimum input voltage may be as low as 4V and the maximum up to 36V, with even higher transient voltages. With these high input voltages, linear regulators cannot be used for high supply currents without overheating the regulator. Instead, high efficiency switching regulators such as BL9641 must be used to minimize thermal dissipation. BL9641 is available SOT23-6 Packages.
FEATURES
Wide Input Operating Range from 4V to 38V Standoff Input Voltage: 42V High Efficiency at 12V In 5V Out: Up to 92%: High Efficiency PFM mode at light load Capable of Delivering 0.7A No External Compensation Needed Current Mode control Logic Control Shutdown Thermal shutdown and UVLO Available in SOT23-6 Package
APPLICATIONS
Smart Meters Industrial Applications Automotive Applications PIN OUT SOT23-6 SWBST FB EN GND 5 IN TYPICAL APPLICATION GND FB IN SW VOUT 3.3V/0.5A10μH 49.9K 16.2K EN 50V 10μF 6.3V 22μF BST 10nF1 VIN Standoff up to 42V
www.belling.com.cn 2 BL9641 MARK and ORDERING INFORMATION Mark Explanation aa: Type b: Year c: Week PINOUT DESCRIPTION PIN # NAME DESCRIPTION 1 BST Bootstrap pin. Connect a 10nF capacitor from this pin to SW
2 GND Ground
3 FB Feedback Input. Connect an external resistor divider from the output to FB and GND to set VOUT 4 EN Enable pin for the IC. Drive this pin high to enable the part, low to disable. 5 IN Supply Voltage. Bypass with a 10μF ceramic capacitor to GND 6 SW Inductor Connection. Connect an inductor Between SW and the regulator output. BLOCK DIAGRAM REG &REF PWM Logic DRIVER FB Slope Comp OSC Σ IN BST SW GND UVLO & Thermal shutdown Current Sense EA EN COMP network
www.belling.com.cn 3 BL9641 ABSOLUTE MAXIMUM RATING Parameter Value Input Voltage Range -0.3V-42V SW, EN Voltage –0.3V to VIN+0.3V BST Voltage –0.3V to SW+6V FB Voltage –0.3V to 6V SW to ground curren Internally limited Operating Junction Temperature(Tj) -40C –85C Storage Temperature(Ts) -55C - 150C Note: Exceed these limits to damage to the device. Exposure to absolute maximum rating conditions may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 12V, unless otherwise specified. Typical values are at TA = 25C .) PARAMETER CONDITIONS MIN TYP MAX UNITS Input Standoff Voltage 42 V Input Voltage Range 4 38 V Input UVLO Rising, Hysteresis=140mV 3.80 V Input OVP Rising, Hysteresis=1.3V 38 V Input Supply Current VFB =0.85V 0.6 mA Input Shutdown Current 6 μA FB Feedback Voltage 0.800 V FB Input Current 0.01 μA Switching Frequency 660 KHz Maximum Duty Cycle 90 % FoldBack Frequency VFB = 0V 60 KHz High side Switch On Resistance ISW =200mA 400 mΩ High side Switch Current Limit 1.2 A SW Leakage Current VIN=12V,VSW=0, EN= GND 10 μA EN Input Current VIN=12V ,VEN =5V 1 5 μA EN Input Low Voltage Rising, Hysteresis=100mV 0.8 1.1 1.4 V Thermal Shutdown Hysteresis=40° C 150 °C
www.belling.com.cn 4 BL9641 TYPICAL PERFORMANCE CHARACTERISTICS (Typical values are at TA = 25C unless otherwise specified.)
www.belling.com.cn 5 BL9641 TYPICAL CHARACTERISTICS (Typical values are at TA = 25C unless otherwise specified.) Start-up Waveform with EN VIN=12V,VOUT=5V,IOUT=0A 5ms/div VEN VOUT ISW Start-up Waveform with EN=VIN VIN=12V,VOUT=5V,IOUT=0A 5ms/div Shutdown Waveform with EN VIN=30V,VOUT=5V,IOUT=0.5A 5ms/div VOUT ISW ISW VIN VOUT VSW VSW VEN VSW Switching Waveform VIN=12V,VOUT=5V,IOUT=0.1A 5ms/div VOUT Switching Waveform VIN=12V,VOUT=5V,IOUT=0.3A 5ms/div Load Transient Response VIN=12V,VOUT=3.3V,IOUT=0 to 0.5A 5ms/div VOUT ISW VOUT VSW VSW Load Transient Response VIN=12V,VOUT=5V,IOUT=0 to 0.5A 5ms/div VOUT ISW Short-Circuit Response VIN=24V,VOUT=5V,IOUT=0A to Short 5ms/div Short-Circuit Recovery VIN=24V,VOUT=5V,IOUT= Short to 0A 5ms/div VOUT ISW ISW VOUT
www.belling.com.cn 6 BL9641 FUNCTIONAL DECRIPTIONS Loop Operation The BL9641 is a wide input range, high-efficiency, DC-to-DC step-down switching regulator, capable of delivering up to 0.7A of output current, integrated with a 400mΩ high side MOSFET. It uses a PWM current -mode control scheme. An error amplifier integrates error between the FB signal and the internal reference voltage. The output of the integrator is then compared to the sum of a current-sense signal and the slope compensation ramp. This operation generates a PWM signal that modulates the duty cycle of the power MOSFETs to achieve regulation for output voltage. Light Load Operation Traditionally, a fixed constant frequency PWM DC-DC regulator always switches even when the output load is small. When energy is shuffling back and forth through the power MOSFETs, power is lost due to the finite RDSONs of the MOSFETs and parasitic capacitances. At light load, this loss is prominent and efficiency is therefore very low. BL9641 employs a proprietary control scheme that improves efficiency in this situation by enabling the device into a power save mode during light load, thereby extending the range of high efficiency operation.
APPLICATION INFORMATION
Output voltages are set by external resistors. The FB threshold is 0.8V. RTOP = RBOTTOM x [(VOUT / 0.8) - 1] Inductor Selection The peak-to-peak ripple is limited to 30% of the maximum output current. This places the peak current far enough from the minimum overcurrent trip level to ensure reliable operation while providing enough current ripples for the current mode converter to operate stably. In this case, for 0.7A maximum output current, the maximum inductor ripple current is 300 mA. The inductor size is estimated as following equation: LIDEAL=(VIN(MAX)-VOUT)/IRIPPLE*DMIN*(1/FOSC) Therefore, for VOUT=5V, The inductor values is calculated to be L = 13μH. Chose 10μH or 15Μh For VOUT =3.3V,The inductor values is calculated to be L = 9.2μH. Chose 10μH Output Capacitor Selection For most applications a nominal 22μF or larger capacitor is suitable. The ETA2841 internal compensation is designed for a fixed corner frequency that is equal to FC= 8.7Khz For example, for VOUT=5V, L=15μH, COUT=22μF. The output capacitor keeps output ripple small and ensures control -loop stability. The output capacitor must also have low impedance at the switching frequency. Ceramic, polymer, and tant alum capacitors are suitable, with ceramic exhibiting the lowest ESR and high-frequency impedance. Output ripple with a ceramic output capacitor is approximately as follows:VRIPPLE = IL(PEAK)[1 / (2π x fOSC x COUT)] If the capacitor has significant ESR, the output ripple component due to capacitor ESR is as follows: VRIPPLE(ESR) = IL(PEAK) x ESR Input Capacitor Selection The input capacitor in a DC-to-DC converter reduces current peaks drawn from the battery or other input power source and reduces switching noise in the controller. The impedance of the input capacitor at the switching frequency should be less than that of the input source so high-frequency switching currents do not pass through the input source. The output capacitor keeps output ripple small and ensures control-loop stability. Components Selection VOUT (V) COUT (μF) L (μH) 8 22 15 to 22 5 22 10 to 15 3.3 22 6.8 to 10
www.belling.com.cn 7 BL9641 PACKAGE OUTLINE