BL9309 BELLING | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
www.belling.com.cn V1.1 1 BL9309 5.5V 2.0A 1.3MHz Synchronous Buck Converter GENERATION DESCRIPTION The BL9309 is a high-efficiency, DC-to-DC step-down switching regulators, capable of delivering up to 2A of output current. The device operates from an input voltage range of 2.5V to 5.5V and provides an output voltage from 0.6V to VIN, making the BL9309 ideal for low voltage power conversions. Running at a fixed frequency of 1.3MHz allows the use of small external components, such as ceramic input and output caps, as well as small inductors, while still providing low output ripples. This low noise output along with its excellent efficiency achieved by the internal synchronous rectifier, making BL9309 an ideal green replacement for large power consuming linear regulators. Internal soft-start control circuitry reduces inrush current. Short-circuit and thermal-overload protection improves design reliability. The BL9309 is available in a SOT23-6 and SOT23-5 Package.
FEATURES
High Efficiency: Up to 97% Capable of Delivering 2A 1.3MHz Switching Frequency No External Schottky Diode Needed Light-load Mode Internal Compensation and Soft-Start Current Mode control 0.6V Reference for Low Output voltages Logic Control Shutdown (IQ<1uA) Thermal shutdown and UVLO Available in SOT23-6 and SOT23-5
APPLICATIONS
Digital Cameras MP3 and MP4 players Set top boxes Wireless and DSL Modems USB supplied Devices in Notebooks Portable Devices TYPICAL APPLICATION CIRCUIT PIN ASSIGNMENT ORDER INFORMATION PART NO PACKAGE TEMPERATURE TAPE & REEL BL9309 SOT23-6 -40 ~ +85℃ 3000/REEL BL9309 SOT23-5 -40 ~ +85℃ 3000/REEL
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 2 PIN DESCRIPTION PIN NO SYMBOL DESCRIPTTION SOT23-6 SOT23-5 1 1 EN Enable pin 2 2 GND Ground 3 3 SW Power Switch Output 4 4 IN Power Supply Input
5 NC Not Connected
ABSOLUTE MAXIMUM RATINGS (Note 1) Parameter Value Max Input Voltage 6.5V Max Operating Junction Temperature(Tj) 125C Ambient Temperature(Ta) -40C – 85C Maximum Power Dissipation SOT23-5 400mW Storage Temperature(Ts) -40C - 150C Lead Temperature & Time 260C, 10S Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Range indicates c onditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Range. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. RECOMMANDED OPERATING RANGE SYMBOL ITEMS VALUE UNIT VIN VIN Supply Voltage 2.5 to 5.5 V TOPT Operating Temperature -40 to +85 ℃ ELECTRICAL CHARACTERISTICS (Note 2, 3)(VDD=5V, TA=25C)
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 3 SIMPLIFIED BLOCK DIAGRAM OPERATION DESCRIPTION The BL9309 high-efficiency switching regulator is a small, simple, DC-to-DC step-down converter capable of delivering up to 2A of output current. The device operates in pulse-width modulation (PWM) at 1.3MHz from a 2.5V to 5.5V input voltage and provides an output voltage from 0.6V on, making the BL9309 ideal for on-board pos t-regulation applications. An internal synchronous rectifier improves efficiency and eliminates the typical Schottky free-wheeling diode. Using the on resistance of the internal high-side MOSFET to sense switching currents eli minates current-sense resi stors, further improving efficiency and cost. Loop Operation BL9309 uses a PWM current-mode control scheme. An open-loop comparator compares the i ntegrated voltage-feedback signal against the sum of the amplified current-sense signal and the slope compensation ramp. At each rising edge of the internal clock, the internal high-side MOSFET turns on until the PWM comparator terminates the on cycle. During this on-time, current ramps up through the inductor, sourcing current to the output and storing energy in the inductor. The current mode feedback system regulates the peak inductor current as a function of the output voltage error signal. During the off cycle, the internal high-side P-channel MOSFET turns off, and the internal low-side N-channel MOSFET turns on. The inductor releases the stored energy as its current ramps down while still providing current to the output. Current Sense An internal current-sense amplifier senses the current through the high-side MOSFET during on time and produces a proportional current signal, which is used to sum with the slope compensation signal. The summed signal then is compared with the error amplifier output by the PWM comparator to terminate the on cycle. Current Limit There is a cycle-by-cycle current limit on the high-side MOSFET of 2.5A. When the current flowing out of SW exceeds this limit, the high-side MOSFET turns off and the synchronous rectifier turns on. BL9309 utilizes a frequency fold-back mode to prevent overheating during short-circuit output conditions. The device enters frequency fold-back mode when the FB voltage drops below 200mV, limiting the current to 2.5A and reducing power dissipation. Normal operation resumes upon removal of the short-circuit condition.
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 4 Soft-start BL9309 has a internal soft-start circuitry to reduce supply inrush current during startup conditions. When the device exits under-voltage lockout (UVLO), shutdown m ode, or restarts following a thermal-overload event, the l soft-start circuitry slowly ramps up current available at SW. UVLO and Thermal Shutdown If IN drops below 2.5V, the UVLO circuit inhibits switching. Once IN rises above 2.5V, the UVLO clears, and the soft-start sequence activates. Thermal-overload protection limits total power dissipation in the device. When the junction temperature exceeds TJ= +150°C, a thermal sensor forces the device into shutdown, allowing the die to cool. The thermal sensor turns the device on again after the junction temperature cools by 15°C, resulting in a pulsed output during continuous overload conditions. Following a thermal-shutdown condition, the soft-start sequence begins.
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 5 TYPICAL OPERATING CHARACTERISTICS Tested under TA=25C, unless otherwise specified
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 6
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 7
APPLICATION INFORMATION
Output voltages are set by external resistors. The FB_ threshold is 0.6V. RTOP = RBOT [(VOUT / 0.6) - 1] Input Capacitor Selection The input capacitor in a DC-to-DC converter reduces current peaks drawn from the battery or other input power source and reduces switching noise in the controller. The impedance of the input capacitor at the switching frequency should be less than that of the input source so high-frequency switching currents do not pass through the input source. The output capacitor keeps output ripple small and ensures control-loop stability. The output capacitor must also have low impedance at the switching frequency. Ceramic, polymer, and tantalum capacitors are suitable, with ceramic exhibiting the lowest ESR and high-frequency impedance. Output ripple with a ceramic output capacitor is approximately as follows: VRIPPLE = IL(PEAK)[1 / (2π x fOSC x COUT)] If the capacitor has significant ESR, the output ripple component due to capacitor ESR is as follows: VRIPPLE(ESR) = IL(PEAK) x ESR Output Capacitor and Inductor Selection Follow the below table for Inductor and Output cap selection: COUT 33F 33F 22F 22F 10F If much smaller values are used, inductor current rises, and a larger output capacitance may be required to suppress output ripple. Larger values than LIDEAL can be used to obtain higher output current, but typically with larger inductor size. Layout Guideline Layout is critical to achieve clean and stable operation. The switching power stage requires particular attention. Follow these guidelines for good PC board layout: 1) Place decoupling capacitors as close to the IC as possible 2) Connect input and output capacitors to the same power ground node with a star ground configuration then to IC ground. 3) Keep the high-current paths as short and wide as possible. Keep the path of switching current (C1 to IN and C1 to GND) short. Avoid vias in the switching paths. 4) If possible, connect IN, SW, and GND separately to a large copper area to help cool the IC to further improve efficiency and long-term reliability. 5) Ensure all feedback connections are short and direct. Place the feedback resistors as close to the IC as possible. 6) Route high-speed switching nodes away from sensitive analog area.
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 8 L PACKAGE OUTLINE SYMBOL SOT23-6 MILLIMETERS INCHES MIN MAX MIN MAX A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.400 0.012 0.016 c 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E1 2.650 2.950 0.104 0.116 e 0.950TYP 0.037TYP e1 1.800 2.000 0.071 0.079 L 0.700REF 0.028REF L1 0.300 0.600 0.012 0.024 θ 0° 8° 0° 8°
5.5V 2.0A 1.3MHz Synchronous Buck Converter www.belling.com.cn V1.1 9 Package specification：