AN0017

AN0017 UMS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 32

Technical content

Ref. : AN0017-8206 - 26 Jun 08 1/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 Application Note for Molded Plastic QFN Packages GaAs Monolithic Packaged Microwave IC 1. General considerations on plastic molded packages Surface Mount Device type packages (S MD*) for microwave applications are appearing more and more on the market. The use of such packages requires some specific knowledge in order to optimize the performances. In particular, the design of motherboard has a strong impact on the overall performance since the transition from the motherboard to the pack age is comparably large and, therefore, can lead to strong parasitic effects. The UMS RoHS* compliant plastic QFN* packages, SMT* compatible are appreciated for their very good electrical and thermal performances at low cost. Thanks to a limited area and very short leads, they perfectly suit to the microwave circuits where the package’s parasitic elements must be as small as possible in order to be negligible at high frequency. The best trade-off between electrical performances and industrial constraints is get with a lead to lead pitch of 0.5mm. Today, excellent performances are demonstrated up-to 40G Hz. And the performances of the packaged products are similar to the equivalent bare-dies when the package model is taken into account in MMIC* design. The lead-frame structure made of copper (C194 alloy) includes small leads but also a large metallic exposed-pad acting as an e fficient ground-pad and a thermal drain to the PCB* circuit. So, the thermal and elec trical ground paths are optimum, and the embedded MMIC is working in very good conditions (see Figure 1). QFN top-side view. QFN back-side view. Figure 1 : QFN package outline. See Glossary UMS PART# YYWWZZ Exposed pad Pin#1 index Device part number Date code Mold compound Leads Pin#1 index Top marking

Ref. : AN0017-8206 - 26 Jun 08 2/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 The packages are LASER marked on top- side as shown on the Figure 1. The package top marking includes a Pin#1 index and three lines of text used for the device identification.

• Line 1: UMS logo.
• Line 2: device part number.
• Line 3: date code o YY stands for the two last digits of the assembly year. o WW stands for the week in the assembly year (from 01 to 52). o ZZ are two optional characters used internally at UMS for lot identification. Remark: In some cases, samples or prototypes can be marked with white ink. The mold protection of the plastic QFN acts as a very good mechanical protection for SMT handling steps. When required, the QFN product qualification includes a THB* 85°C / 85% RH / 1000 hours test and a HTOL* / 1000 hours test [4]. The UMS’s QFN plastic packages are compliant with RoHS directive (Pb* free). The list of the materials constituting the product is given on the Figure 2. Figure 2 : QFN products build-up structure.

Ref. : AN0017-8206 - 26 Jun 08 3/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 The QFN devices are designed to be mount ed onto any standard PCB compatible with SMT process. But, of c ourse at millimetre-wave frequencies a special care must be taken at the PCB level to manage a good electrical and thermal matching of the device. This application note gives guide lines and recommendations in order to design the appropriate motherboard and take advantage of the best circuit performances. 2. UMS’s QFN packages outlines Considering the specificities of the microwave products and the impact of the package on the device performances, UMS proposes four types of over-molded plastic package. This family of packages perfectly answers to the high performances objectives and takes advantage of the standard lo w cost solutions available today for mass production. Package case UMS designation Package Outlines QFN 3x3, 16 leads QAG See annex 6.1 QFN 4x4, 24 leads QDG See annex 6.2 QFN 4x5, 24 leads QEG See annex 6.3 QFN 5x5, 28 leads QGG See annex 6.4 The package outlines have been defined bas ed on the JEDEC MO-220 standard [1]. The tolerances indicated on the drawings have been calculated to comply with the standard of several suppliers in order to propose the best industrial solution regarding the application needs like production volumes, cost, etc… Please download periodically from the UMS web site (http://www.ums-gaas.com) the latest version of this applic ation note to be certain to get the latest version of the drawings. 3. PCB design 3.1. General considerations for PCB design The products developed by UMS are test ed on an evaluation board in order to guarantee the best performances at the custom er level in the final equipment. Since the internal design of the GaAs MMIC is generally based on a micr o-strip structure, the motherboard where t he QFN device will be mounted should be designed in accordance with this configuration. The motherboard acts as a: Signal feeding structure to the QFN device: Transmission lines are needed on the PCB. For electromagnetic reasons, a micro-strip mode is generally chosen and helps to avoid parasitic propagations modes on the PCB. It will also help to minimize the electrical transmission losses. The UMS’ QFN packages are generally designed to be matched on 50Ω loads. However, the motherboard in the close area around the QFN device should be designed to have a good impedanc e transition from the micro-strip

Ref. : AN0017-8206 - 26 Jun 08 5/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 3.2. UMS PCBs for prototyping SMD type packages from UMS allow design and fabrication of mm-wave modules at low cost. Therefore, a suitable mother board environment was chosen according to this aim. All tests and verifications were performed on Rogers RO4003. This material has a permittivity of 3.38 and is used with a thickness of 203µm [8mils] and a 1/2oz or less copper cladding. The corresponding 50Ohm transmission line should have a strip width of about 460µm [approximately 18mils]. Other materials with similar properties can be used as well. The evaluation motherboards proposed in this application note were designed for prototyping and manual assembly. They lead to get the best product performances after assembly. The product datasheet generally includes the recommended motherboard used for the product characterization. Sometimes, slight differences can be observed between the motherboard proposed in the datasheet and the typical motherboard recommended in this application note. Thes e differences might come from product specificities, but generally t he land-pattern is strictly equi valent to those proposed in the next paragraph. It is recommended to use as much as po ssible the proposed layout and technology shown in the product’s datasheet in order to achieve the best performances out of the packaged product. 3.2.1. Recommended package land-pattern and package foot-print The contact areas on the motherboard fo r the package connections should be designed according to the foot-prints given in the following table: Package case UMS designation Package foot-print drawings QFN 3x3, 16 leads QAG See annex 6.5 QFN 4x4, 24 leads QDG See annex 6.6 QFN 4x5, 24 leads QEG See annex 6.7 QFN 5x5, 28 leads QGG See annex 6.8 The foot-print layout for the motherboard as given in the pr oduct datasheet is adapted to get the best performance out of the product and, therefore, can differ from product to product. A proper via structure under t he ground pad is very important in order to achieve a good RF and thermal performances. All te sts have been done by using a grid of plated via holes through the substrate wit h a diameter of less than 300µm [12mils] and a spacing lower than 700µm [28mils] from the centres of two adjacent via holes. Via holes grid should cover the whole ar ea of the ground pad. Th e nearest via holes to the RF ports should be as close as po ssible of the ground pad edges to allow a good RF ground connection. Since via holes are also important for heat transfer, a

Ref. : AN0017-8206 - 26 Jun 08 6/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 proper via filling should be guaranteed during the mounting procedure to get a low thermal resistance between the package and the heat sink. However, it is important to consider that via holes internal copper plating will always act as the main thermal drain. Via filling is also recommended for SMT assembly reasons. Conductive epoxy or any other appropriate thermal conductive mate rial can be used before solder past deposition in order to avoid solder wicking in to via holes during the reflow process. This configuration will help to decrease the thermal resistance of the PCB structure, but it will also avoid low package stand-off height. For the power devices the use of heat slugs in the motherboard in stead of a grid of via’s is recommended. The table hereafter gives the via holes geometry for each package type. QFN 16L 3x3 QFN 24L 4x4 QFN 24L 4x5 ( or 5x4) QFN 28L 5X5 Via-hole external diameter (mm) 0.30 0.30 0.30 0.30 Via-hole internal diameter (mm) 0.25 0.25 0.25 0.25 Number of vias under the package 4 12 24 36 Via holes pitch (mm) 0.70 0.70 0.60 0.60 Via holes height (=PCB thickness) (mm) 0.203 0.203 0.203 0.203 Rth_PCB_UMS : Estimated thermal resistance equivalent to the package foot-print on PCB (°C/W) 5.7 1.9 1.0 0.6 3.2.2. UMS’s motherboards layouts Besides of the package foot-prints descr ibed above, the eval uation motherboards includes transmission lines for the micr owave signals and DC path to bias the component. Thanks to advanced design tec hniques, the MMICs which are designed to be embedded in plastic packages have a very good intrinsic stability. So no decoupling capacitor is needed in the QFN package. The decoupling circuits can be reported directly on the PCB using high quality SMD components as close as possible from the QFN package. This conf iguration helps to get the lower cost solution at the sub-system level. Generic evaluation motherboards are given for each package in the following table: Package case UMS designation Motherboard drawings QFN 3x3, 16 leads QAG See annex 6.9 QFN 4x4, 24 leads QDG See annex 6.10 QFN 4x5, 24 leads QEG See annex 6.11 QFN 5x5, 28 leads QGG See annex 6.12

Ref. : AN0017-8206 - 26 Jun 08 7/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 3.3. Motherboard design for large production volumes (SMT process) The application’s motherboard should be designed to be as close as possible to the UMS’s PCB recommended in the datashee t, and then also complying with the constraints of the industr ial SMT processes. Large volumes production equipments and fully automatic SMT assembly lines have s pecific requirements to be taken into account for the application’s PCB design. A large set of parameters will influence the industrial assembly process and the final assembly yield like:

• the PCB stack-up structure
• the PCB materials properties
• the PCB thermal capacitance
• the solder paste properties
• the fabrication toleranc es of the stencil printer
• the placement tool agility and repeatability
• the solder paste reflow profile and the oven properties Since it is not possible to give generic motherboard layout fully compatible with all the industrial SMT processes in this document, this paragraph intent only to give some guide lines, but it should not replace the design rules provided by the industrial assembler who will consider all the param eters and the equipment s capabilities to achieve the best yield in production. 3.3.1. Package foot-print adjust ments for automatic SMT assembly process The foot-print recommended in the paragr aph 3.2.1 must be used to design the application motherboard. But in some cases, for industrial assembly reasons (stencil printer complexity, solder past selected, PCB material, etc…) it could be necessary to decrease the via-hole density under the package. The impact of low via holes density below t he package might have very bad effect on the device performances:
• The PCB thermal resistance will in crease. Then the ambient maximum temperature must be adjust ed in order to keep the ca se temperature (Tcase, see Figure 5) below the maximum value specified in the product datasheet. Figure 5 : Temperature reference point (Tcase) considered in the product datasheet. Tcase Example of QFN 16L 3x3 back-side view, temperature reference point (Tcase)

Ref. : AN0017-8206 - 26 Jun 08 8/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 Remark: A similar effect on the device t hermal performances is observed when the PCB thickness increases.

• The electrical grounding of the pa ckage could be also affected. It’s recommended to locate the via holes at the edges of the ground pad area as recommended on the UMS’s foot -print drawings in order to avoid device mismatch of unsuitable propagation modes (see filled scares on the Figure 6, the un-filled scares correspond to thermal via holes). Figure 6 : Via holes location (package foot-print QFN 16L 4x4). Remark: A modification of the package f oot-print should be done only after an analysis of the impact on the device electrical and thermal performances. 3.3.2. Solder mask design recommendations For compact and low pitch packages as for QFN packages it is difficult to prevent the solder bridging. Generally, a solder mask is used to avoid this kind of issues in production. The solder mask will also help to define the areas where the solder can flow and control the solder homogeneity under the package contacts (leads and exposed pad). Then the quality and the reliability of the solder join are enhanced. The recommended solder mask clearance ar ound the copper pads on the PCB for land pads is 70µm [2.8mils] as shown on the Figure 7. Concerning the package ground pad, it is recommended to manage an overlap of 70µm [2.8mils] minimum on the solder mask over the copper pad (see Figure 8). This configuration is suitable fo r self-centring of the package on the PCB foot-print during reflow process. Remark: The information’s given in this paragraph are only indicative and should not replace the design rules of the PCB manuf acturer. Furthermore, the solder mask design must also take into account the final SMT assembly process used for module as well as the selected solder past characteristics. Grounding via holes Thermal via holes Land pad Ground pad RF pad + RF line

Ref. : AN0017-8206 - 26 Jun 08 11/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 4. PCB assembly 4.1. SMT assembly process flow For the assembly process, the QFN type package can be handled as a standard surface mount component (please refer to the IPC/JEDEC J-ST D-020C standard or equivalent [2]). The use of solder is recommended, standard techniques involving solder paste and reflow process can be us ed (e.g. stencil solder printing, standard pick-and-place equipment, and solder reflow oven). However, caution should be taken to perform a good and reliable contac t over the whole pad area. The standard SMT process flow is given on the Figure 11. Figure 11 : Standard SMT process flow. 4.2. Bill of materials ƒ Motherboard (typically RO4003 or equivalent, 203µm thickness). ƒ SMD product. ƒ SMD components that might be necessary. ƒ Solder paste (RoHS compliant, but SN63/Pb37 might be used also). ƒ An appropriate solder stencil printer. ƒ A hot plate or a reflow oven. 4.3. Component placement UMS proposes antistatic tubes or tape&r eel as standard delivery conditioning for QFN devices. Tape&reel conditioning is appreciated for automatic SMT assembly lines. The QFN device is orientated in the tape&reel pockets as shown on Figure 12 and following the norm EIA-481 [5]. Automatic recognition system s will detect the QFN orientation in the tape&reel pocket to align the device on the PCB. In spite of discrepancies between suppliers that could affect the recognition system (top marking aspect, the lead finish aspect) , the relative position of the Pin#1 indicator on top marking to the tape&reel feeding direction is the key parameter to drive the placement process. Solder Screen Printing Component placement Reflow soldering Inspection

Ref. : AN0017-8206 - 26 Jun 08 14/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 During the assembly reflow the moistu re absorbed by the mold compound after storage will be vaporized. Then depending on t he percentage of humidity contained in the resin, high mechanical constraints might be applied to the package. The MSL* is an indicator fo r the maximum allowable time period (Floor Life Time) during which a moisture sensitive plastic device, once removed from the dry bag, can be exposed to an environment with a maximum temperature of 30°C and a maximum relative humidity of 60%RH or 85%RH before the solder reflow process: MSL Level MSL4 MSL3 MSL2A MSL2 MSL1 Floor Life (out of bag) at factory ambient 72hours 168hours 192hours 1year Unlimited Max. storage temperature Max. storage relative humidity ≤60%RH ≤60%RH ≤60%RH ≤60%RH ≤85%RH For details, refer to IPC/JEDEC J-STD-020C [2]. UMS standard offer is from MSL2 to MSL1. MLS1 is easier to achieve on the small packages than on the large ones as QFN 4x5 and 5x5. For MSL4 to MSL2, if during the device storage time none of the conditions below has been exceeded, the device Floor Life Time can be reset after a baking.

• Condition 1: Floor Life Time exceeded and storage conditions during this time ≤30°C and ≤60%RH.
• Condition 2: Device storage conditions have never exceeded ≤40°C and ≤85%RH. The backing conditions are described in the table below: Bake @ 125°C Bake @ 90°C ≤5%RH Bake @ 40°C ≤5%RH Package Body thickness ≤1.4mm Exceeding Floor Life by>72h Exceeding Floor Life by≤72h Exceeding Floor Life by>72h Exceeding Floor Life by≤72h Exceeding Floor Life by>72h Exceeding Floor Life by≤72h Bake duration @ MSL2 5hours 3hours 17hours 11hours 8days 5days Bake duration @ MSL2a 7hours 5hours 23hours 13hours 9days 7days Bake duration @ MSL3 9hours 7hours 33hours 23hours 13days 9days Bake duration @ MSL4 11hours 7hours 37hours 23hours 15days 9days For details, refer to IPC/JEDEC J-STD-033B [3].

Ref. : AN0017-8206 - 26 Jun 08 15/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 4.6. Inspection The quality of the solder joint will be ins pected by X-Ray analyse. This technique helps to detect a defective brazing quality where solder voids are present under the package exposed pad. The solder joint quality can be also in spected on the lead edges. After the QFN singulation the lead endings of the UMS’s packages are visible at the package edges (see Figure 16). During the reflow process, the solder will melt on these surfaces. This configuration has two main advantages. Firstly, the solder joint on the lead edges help to get a robust lead to the PCB attachment. Secondly, a standard visual inspection can confirm that all the package leads are connected to the PCB. Figure 16: QFN side view showing the lead endings after dicing. 4.7. Procedure for prototyping The different steps are: 1. The motherboard should be cleaned with Acetone and rinsed with alcohol and DI* water. Afterwards the circuit should be fully dried. 2. The solder paste dispense should be done according to the patterns shown in the paragraph 3.3.2. It is im portant to note that an ex cessive use of solder paste can cause electrical shorts leading to poor RF performances. 3. A packaged product should be placed on the motherboard with a correct orientation and a good alignment (see t he corresponding product datasheet). The alignment can be done manually by centring the packaged MMIC on the motherboard. 4. Then a reflow of the assembly shoul d be performed on a hot plate for 5 to 6 seconds. The temperature of the pl ate surface should be about 240°C – 260°C. 5. The assembly should cool down completely after the reflow process. 6. The whole assembly should be fi nally cleaned with acetone and rinsed with alcohol and DI water. Lead ending (copper) Tie bar ending (copper) Mold

Ref. : AN0017-8206 - 26 Jun 08 16/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 5. Datasheet electrical information and de-embedding method for the scattering parameters exploitation The RF performances of the QFN dev ice might be enhanced by external (on motherboard) specific shapes for the input and output RF lines, providing local re- matching (using stub and/or slug) in a dedi cated frequency sub-band. To ease the design of the custom motherboard layou t, the Sij (scattering ) parameters are provided in the product datasheet. Thes e Sij parameters ar e measured on the motherboard recommended in the product datasheet. The corresponding Touchtone compatible files (.s2p) can be also downloaded from the UMS’s web site. In order to design the appropriate matching network on the PCB, it is necessary to take into account the location of t he calibration plans used for the scattering parameters measurement in cluded to the product data-s heet (Figure 17). These drawings show the distance in millimetres from the centre of the QFN device to the access ports where the Sij parameters are given for each of the QFN’s used by UMS. QFN 3x3 QFN 4x4 and QFN 4x5 QFN 5x4 and QFN 5x5 Figure 17 : Calibration plans for Sij measurements reported in the product datasheet (drawings not to scale). QFN 16L 3x3 QFN 24L 4x4 (or 4x5) QFN 28L 5X5 (or 5x4) Sij access ports to package centre distance 2.65 mm 3.18 mm 3.66 mm Ports to package-centre distance considered for the Sij measurements reported in the product datasheet.

Ref. : AN0017-8206 - 26 Jun 08 17/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6. Annexes 6.1. QFN 3x3, 16 leads outline

Ref. : AN0017-8206 - 26 Jun 08 18/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.2. QFN 4x4, 24 leads outline

Ref. : AN0017-8206 - 26 Jun 08 19/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.3. QFN 4x5, 24 leads outline

Ref. : AN0017-8206 - 26 Jun 08 20/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.4. QFN 5x5, 28 leads outline

Ref. : AN0017-8206 - 26 Jun 08 21/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.5. Recommended foot-print for QFN 3x3, 16 leads

Ref. : AN0017-8206 - 26 Jun 08 22/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.6. Recommended foot-print for QFN 4x4, 24 leads

Ref. : AN0017-8206 - 26 Jun 08 23/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.7. Recommended foot-print for QFN 4x5, 24 leads

Ref. : AN0017-8206 - 26 Jun 08 24/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.8. Recommended foot-print for QFN 5x5, 28 leads

Ref. : AN0017-8206 - 26 Jun 08 25/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.9. Recommended evaluation board for QFN 3x3, 16 leads

Ref. : AN0017-8206 - 26 Jun 08 26/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.10. Recommended evaluation board for QFN 4x4, 24 leads

Ref. : AN0017-8206 - 26 Jun 08 27/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.11. Recommended evaluation board for QFN 4x5, 24 leads

Ref. : AN0017-8206 - 26 Jun 08 28/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 6.12. Recommended evaluation board for QFN 5x5, 28 leads

Ref. : AN0017-8206 - 26 Jun 08 29/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 7. Glossary SMD : Surface Mount Device SMT : Surface Mount Techniques QFN : Quad Flat Non-leaded PCB : Printed Circuit Board BOM : Bill Of Materials Sij : Scattering Parameters RoHS : Restriction of the use of certain Hazardous Substances Lead-free : Part of the RoHS directive DI : Deionised water MMIC : Monolithic Microw ave Integrated Circuit THB : Temperature and Humidity Biased HOTL : High Temperature Operating Life Pb : Lead MSL : Moisture Sensitivity Level 8. References [1] : JEDEC MO-220. Thermally enhanced plastic very thin and very very thin fin pitch quad flat no lead package. [2] : IPC/JEDEC J-STD-020C. Moisture/reflo w sensitivity classification for non hermetic solid-state surface-mount devices. [3] : IPC/JEDEC J-STD-033B. Handling, pa cking shipping and use of moisture/reflow sensitive surface mount devices. [4] : JEDEC JESD47D. Stress-test-driven qualification of integrated circuits. [5] : EIA STANDARD – 481. Taping of SMD.

Ref. : AN0017-8206 - 26 Jun 08 30/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 Table of contents 5. Datasheet electrical information and de-embedding method for the scattering parameters

Ref. : AN0017-8206 - 26 Jun 08 31/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09

Ref. : AN0017-8206 - 26 Jun 08 32/32 Subject to change without notice United Monolithic Semiconductors S.A.S. Route Départementale 128 - BP46 - 91401 Orsay Cedex France Tel.: +33 (0)1 69 33 03 08 - Fax: +33 (0)1 69 33 03 09 Notes: Contacts: Web site: www.ums-gaas.com email: mktsales@ums-gaas.com Phone: 33 (1) 69 33 02 26 (France) +1 973 812 2139 (USA) +86 21 6103 1635 (China) Information furnished is believed to be accurate and reliable. However United Monolithic Semiconductors S.A.S. assumes no responsibility for the c onsequences of use of such informat ion nor for any infringement of patents or other rights of thir d parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of United Monolithic Semiconductors S.A.S. . Specifications mentioned in this publication are subj ect to change without notice. This pub lication supersedes and replaces all information previously supplied. United Monolithic Semiconductors S.A.S. products are not authorised for use as critical components in life support devices or systems without express written approval from United Monolithic Semiconductors S.A.S.