AMW37-H35GHJR

Silicon Laboratories

Embedded Wi-Fi Networking Solution August 29, 2017

Manufacturer: Silicon Laboratories

Document: 32 Pages / 2Mb

Request Quote Download Datasheet Read online HTML view

More from Silicon Laboratories Browse A parts

Online Datasheet

Read AMW37-H35GHJR online.

AMW037 SILABS | Alldatasheet

Document overview

Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
PDF pages: 32

Technical content

Datasheet sections

1 General Description
1.1 ZentriOS
2 Block Diagram
3 Electrical Specifications
3.1 Absolute Maximum Ratings
3.2 Recommended Operating Conditions
3.3 Power Consumption
3.4 Digital IO Characteristics
4 WLAN RF Specifications
4.1 Summary WLAN Specifications
4.2 WLAN Specifications
5 Pinout and Signal Descriptions
5.1 Pinout
5.2 Pin Description
6 Design Guidelines
6.1 Dimensions
6.3 Recommended PCB Footprint
6.4 Routing Recommendations
6.5 Soldering Information
6.6 Application Examples
7 Regulatory Certification
7.1 United States
7.3 Canada
7.5 Europe
7.6 Australia
7.7 New Zealand
8 Packaging, Handling and Storage, RoHS
8.1 Packaging
8.2 Handling & Storage
8.3 RoHS Directive
8.4 Tape and Reel Specifications
9 Ordering Information
9.1 Ordering an Unspecified ZentriOS Version
9.2 Ordering a Specific ZentriOS -WL Version or a
9.3 ZentriOS Version History
10 Revision History & Glossary
10.1 Revision History
10.2 Glossary
11 References

ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | i AMW037 • AMW037 Datasheet Disclaimer While the information provided in this document is be- lieved to be accurate, it is under development and Zentri reserves the right to make changes without further no- tice to the product described herein to improve reliabil- ity, function, or design, and makes no guarantee or war- ranty concerning the accuracy of said information, nor shall it be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon, such information. Zentri makes no warranties of any kind, whether express, implied or arising by custom or course of trade or performance, and specifically disclaims the implied warranties of title, non-infringement, merchant- ability, or fitness for a particular purpose. No part of this document may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photographic, or otherwise, or used as the basis for manufacture or sale of any items without the prior written consent of Zentri. Trademarks Zentri and the Zentri logo are trademarks of Zentri. Other trademarks in this document belong to their respective owners. © 2014-2017 Zentri All rights reserved. Document Number: ADS-MW037-101R Release Date: August 29, 2017 Contact https://www.silabs.com/about-us/contact-us About this Data Sheet This document provides information on the AMW037 802.11b/g/n Wi-Fi networking module from Zentri. Specifications for the module I/O, peripherals the WLAN subsystem were compiled from vendor datasheets and measured data. Organization This data sheet is organized into the following sections: Not Recommended for New Designs

ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | ii AMW037 Data Sheet Embedded Wi-Fi Networking Solution General Features  Self-contained ultra-low power Wi-Fi module with industry standard SSL/TLS secure TCP/IP network stack and PCB Trace antenna.  Integrated SPI-serial flash for software upgrades and user accessible read/write file system Wi-Fi  Single band 2.4GHz IEEE 802.11b/g/n 1x1 Wi-Fi transceiver  Includes support for all Wi-Fi security modes includ- ing Open, WEP, WPA, and WPA2-PSK Microprocessor  32-bit application processor  Operates up to 160MHz core frequency Interfaces*  UART: 1 x 4-wire, 1 x TX only up to 4.5Mbit/s  GPIO: Up to 8 GPIOs (overlaid with peripherals)  A/D converter: 1 x 10-bit resolution  PWM: Up to 4 PWM outputs  Wake-up: Wake pin for ultra-low power operation *Some interfaces share module pins Operational & Radio  Single operating voltage : 3.3V (typical)  Operational Temperature Range: -40°C to +85°C  Weight : 0.03 oz (1g)  Current consumption @ 3.3V, 25°C - Standby : 0.9mA - Deep sleep / RTC : 20 / 60µA - Sleep (Memory Retention) : 0.31mA - Wi-Fi Powersave : 0.86mA (DTIM = 3) - Active receive : 65mA - Active transmit :  100mA @ +0dBm  200mA @ +18dBm  Maximum RF transmit power - 802.11b/g : +20 dBm - 802.11n : +16 dBm  Minimum Receive sensitivity - 802.11b/g : -93 dBm - 802.11n : -85 dBm

Applications

 Industrial, M2M and Home Automation - Environmental monitoring - Energy monitoring - Wireless sensing, remote data logging - HVAC, power, light, & thermostat control - Appliance control  Security - Cameras, Doors/Window monitoring - Alarms, Smoke Detectors - Door and entry control  Health & Fitness - Fitness Equipment - Home health monitoring e.g. weight scales  Consumer - Audio, Toys, Robots Not Recommended for New Designs

ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | iii ZentriOS-WL Firmware Features The ZentriOS-WL firmware supplied with the AMW037 provides a wide range of features beyond the underly- ing hardware, and supports application development via its command API. For complete documentation of ZentriOS-WL, see: https://docs.zentri.com/zentrios/wl/latest/ Software APIs  ZentriOS-WL command API Interfaces  Serial (UART, remote terminal)  SoftAP and WLAN client (not concurrent) Servers  TCP, UDP, HTTP, DHCP, DNS  HTTP Server with RESTful API  Fully customizable mobile responsive Web ap- plication with JavaScript and Python libraries Clients  TCP, TLS, NTP, DHCP, DNS  HTTP(S) client  Websocket client Setup  Multiple Wi-Fi setup options, including via serial command and Web setup with SoftAP Peripherals and Sensors  GPIOs for control, indication and monitoring  Automated broadcast and streaming of sensor data  Local caching of sensor data Update and Recovery Wireless OTA (Over-the-Air) update to remote manage firmware using the Zentri DMS (Device Management Service) System Management  System configuration and monitoring via setting and getting a wide range of variables  Configurable power states Sleep/wake timers File System  Read/write file system  Storage of large files  HTTP download to file system, HTTP upload from file system Not Recommended for New Designs

1 General Description

The AMW037 module from Zentri provides an ad- vanced stand-alone Wi-Fi and networking solution. An integrated module avoids difficult RF layout and ena- bles designers to rapidly embed Wi-Fi and secure net- working functionality into virtually any device. The ZentriOS embedded connected operating system , pre-programmed into all modules, may be used to fast- track module integration into end-products. With dimensions of just 16.5mm x 23.5 mm and a wide temperature range, the module is suitable for integra- tion into most embedded applications. The Wi- Fi device includes an integrated RF transmit power amplifier and provides superior Wi-Fi perfor- mance and full compatibility with all 2.4GHz 802.11b/g/n Wi-Fi networks. The AMW037 microcontroller core operat es at a fre- quency of 160MHz. The AMW037 module offers extensive I/O and periph- eral interfaces listed below, and provides additional interface combinations by leveraging multiplexing and alternate function capabilities.  1 x 4-Wire UART interface  8 x GPIOs  1 x 10-bit A/D converters  4 x PWM outputs  1 x ultra-low power wake input The module is powered by a single 3.3V power supply. Various powersave modes offer ultra-low power opera- tion. Wake from low power sleep mode is possible using IO pins or the internal real-time clock, and wake from ul- tra-low power standby mode is achieved using the dedi- cated wake pin. The module has numerous modular approvals. See Sec- tion 7, Regulatory Certification.

1.1 ZentriOS

This document is designed to cover the physical and electrical characteristics of the AMW037 module. For information on ZentriOS see: http://docs.zentri.com/zentrios/wl/latest/ Not Recommended for New Designs

2 MByte

2 Block Diagram

Figure 1. AMW037 Architecture

3 Electrical Specifications

3.1 Absolute Maximum Ratings

Table 1. Absolute Maximum Voltage Ratings Table 2. Absolute Maximum Environmental Ratings

3.2 Recommended Operating Conditions

limits for extended periods can adversely affect long-term reliability of the device. Table 3. Recommended DC Operating Conditions

The performance of the Wi-Fi subsystem is degraded significantly at low voltages

Table 4. Recommended Environmental Conditions

If you require an extended temperature range, contact Zentri.

3.3 Power Consumption

Table 5. Power consumption (VDD_3V3, VDD_WIFI, VBAT @ 3.3V)

3.4 Digital IO Characteristics

to minimize power consumption. must be stronger than the positive feedback. The required drive strength is however small – in the range of 5uA. Table 6. Digital IO Characteristics

4 WLAN RF Specifications

other antenna port terminated in 50 ohms.

4.1 Summary WLAN Specifications

Table 7. Summary WLAN Specifications

4.2 WLAN Specifications

Table 8. WLAN Receiver Performance Specifications

1 Mbps DSSS – -98 –

6 Mbps OFDM – -93 –

PSDU) at either antenna port.

6.5 Mbps MCS0, HT20

65 Mbps MCS7, HT20

Operation below -20°C and above +65°C with parameter derating per Note 2
Derate receive sensitivity by 1.5dB for operation between temperatures of -40°C to -20°C and 65°C to 85°C

5 Pinout and Signal Descriptions

5.1 Pinout

footprint is provided in Section 6.2. Figure 2. AMW037 Pinout (TOP View – Pins NOT visible from top!)

5.2 Pin Description

Table 9. AMW037 Pin Definitions

1 GND S Ground -

3 ADC A ADC -

6 WAKE O WAKE (1k resistor to RESET_N)

8 GPIO_0 I/O GPIO /

9 GPIO_1 I/O GPIO PWM_1

10 UART_RX I/O - -

11 UART_TX I/O - Boot Control3

12 GND S Ground -

13 GPIO_2 I/O GPIO Boot Control3

14 GPIO_3 IO GPIO Boot Control3

15 GPIO_4 I/O GPIO PWM2

Pinout and Signal Descriptions, Section 5 AMW037 Datasheet ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | 10 Pin Name Type1 Primary Function Alternate & Other Function(s) 16-22 - NC - -

23 GND S Ground -

24 GPIO_5 I/O GPIO -

29 RESET_N I RESET -

30 GPIO_6 I/O GPIO UART_CTS

31 GPIO_7 I/O GPIO UART_RTS

33 CHIP_EN I Chip Enable VDD = Enable module

GND = Deep Sleep Mode (onboard 100k pull up) 34-44 GND S - - Notes: 1. I = Input, O = Output, S = Supply, A = Analog, NC = No Connection (Do not connect to ground) 2. The Wi-Fi Antenna pin is AC-coupled and has a nominal 50 ohms output impedance. 3. The Boot Control pins must be at the following levels immediately after a reset in order for the module to boot correctly: UART_TX = GND, GPIO_2 = VDD, GPIO_3 = VDD Not Recommended for New Designs

6 Design Guidelines

6.1 Dimensions

Figure 3 - AMW037 Spectre Dimensions Figure 4 - AMW037 Spectre Dimensions Symbol Imperial (thou) Tolerance (thou) Metric (mm) Tolerance (mm) A 101 ±6 2.57 ±0.15 A1 30 ±3 0.76 ±0.08 A2 71 ±6 1.80 ±0.15 D 975 ±5 24.77 ±0.13 D1 133 ±5 3.38 ±0.13 D2 433 ±6 11.00 ±0.15 D3 358 ±5 9.09 ±0.13 E 650 ±5 16.51 ±0.13 E1 88 ±5 2.24 ±0.13 E2 472 ±6 12.00 ±0.15 E3 88 ±5 2.24 ±0.13 Not Recommended for New Designs

6.3 Recommended PCB Footprint

All dimensions in Figure 5 are in thousands of an inch unless otherwise marked. Figure 5. AMW037 Recommended Footprint (Top)

6.4 Routing Recommendations

plane. Failure to comply with these recommendations may result in degraded performance of WLAN functionality.

6.5 Soldering Information

Figure 6 - Recommended solder reflow profile Figure 7 - Example solder reflow profile (AMW037-E03 evaluation board) Not Recommended for New Designs

6.6 Application Examples

up/down resistors are included inside the module. The general guidelines for the AMWx06 devices apply to all Zentri devices. Figure 8. Using the AMW037 Module with ZentriOS and a UART serial interface

7 Regulatory Certification

The AMW037 module has been certified for operation in various regulatory domains. This section outlines certifi- cation information specific to the following countries and regions:  United States  Canada  Europe  Australia  New Zealand The certifications listed in this section are valid at the time of publication. For up- to-date information refer to Zentri documentation online at: https://docs.zentri.com. All AMW037 test reports are available on the Zentri web- site at: https://docs.zentri.com/zentri/docresources#amw037 Should you require regulatory certification for the AMW037 module in a country or region not listed, please contact your local Zentri sales office or create a support request via our website at https://www.silabs.com/about-us/contact-us

7.1 United States

The Zentri AMW037 module has received Federal Com- munications Commission (FCC) CFR47 Telecommunica- tions, Part 15 Sub-part C “Intentional Radiators” modular approval in accordance with Part 15.212 Modular Trans- mitter approval. Modular approval allows the end user to integrate the AMW037 module into a finished product without obtaining subsequent and separate FCC approv- als for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or modifications could void the user’s authority to oper- ate the equipment. The end user must comply with all of the instructions provided by the Grantee which indicate installation and/or operating conditions necessary for compliance. The finished product is required to comply with all appli- cable FCC equipment authorization, regulations, require- ments, and equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated to regulations for other transmit- ter components within the host product; to require- ments for unintentional radiators (Part 15 Sub-part B “Unintentional Radiators”), such as digital devices, com- puter peripherals, radio receivers, etc.; and to additional authorization requirements for non-transmitter func- tions on the transmitter module (i.e. Verification, or Dec- laration of Conformity) (e.g., transmitter modules may also contain digital logic functions) as appropriate. Labeling and User Information Requirements The AMW037 module has been labelled with a unique FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the out- side of the finished product into which the module is in- stalled must also display a label referring to the enclosed module. This exterior label can use wording as follows: If the exterior label area is smaller than the palm of the hand, the end product user manual must contain the above statement. The user manual should contain the following additional statement: Contains FCC ID: 2ABPY-5B9198 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause unde- sired operation. Not Recommended for New Designs

Regulatory Certification, Section 7 AMW037 Datasheet ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | 16 The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engi- neering and Technology (OET) Laboratory Division Knowledge Database (KDB) at the following website: http://www.fcc.gov For products available in the USA/Canada market, only channels 1 to 11 can be operated. Selection of other channels is not possible. This module is intended for OEM integrators. The OEM integrator is responsible for compliance in all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. RF Exposure All transmitters regulated by FCC must comply with RF exposure requirements. OET Bulletin 65, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, provides assis- tance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal Communications Commission (FCC). The bulletin offers guidelines and suggestions for evaluating compliance. If appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels and by providing users with in- formation concerning minimum separation distances from transmitting structures and proper installation of antennas. The following statement must be included as a CAUTION statement in manuals and OEM products to alert users of FCC RF exposure compliance: If the AMW037 module is used in a portable application (i.e., the antenna is less than 20 cm from persons during operation), the integrator is responsible for performing Specific Absorption Rate (SAR) testing in accordance with FCC rules 2.1091. Further Information Additional information regarding FCC certification and use of the AMW037 module in the United States is avail- able from the following sources.  Federal Communications Commission (FCC) http://www.fcc.gov This equipment has been tested and found to com - ply with the limits for a Class B digital device, pursu- ant to part 15 of the FCC Rules. These limits are de- signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre- quency energy and if not installed and used in ac- cordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular install ation. If this equipment does cause harmful interference to radio or television re- ception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equip- ment and receiver.  Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained be- tween the antenna of this device and persons dur- ing operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Not Recommended for New Designs

7.3 Canada

The AMW037 module has been certified for use in Can- ada under Industry Canada (IC) Radio Standards Specifi- cation (RSS) RSS-210 and RSSGen. Modular approval per- mits the installation of a module in a host device without the need to recertify the device. Labeling and User Information Requirements Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host de- vice shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to dis- play the Industry Canada certification number of the module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording ex- pressing the same meaning, as follows: The user documentation should contain the following in- formation: For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other chan- nels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sé- lection d'autres canaux n'est pas possible. The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. User Manual Notice for License-Exempt Radio Apparatus (from Section 7.1.3 RSS-Gen, Issue 3, December 2010): User manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicu- ous location in the user manual or alternatively on the device or both: Transmitter Antenna Notification (from Section 7.1.2 RSS-Gen, Issue 3, December 2010): User manuals for transmitters shall display the following notice in a con- spicuous location: The above notice may be affixed to the device instead of displayed in the user manual. Contains transmitter module IC: 11685A-5B9198 This device complies with Industry Canada license - exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux onditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appa- reil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en com- promettre le fonctionnement. Under Industry Canada regulations, this radio trans- mitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the trans- mitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotrop- ically radiated power ( EIRP) is not mo re than that necessary for successful communication. Conformément à la réglementation d'Industrie Can - ada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infé- rieur) approuvé pour l'émetteur par Industrie Can- ada. Dans le but de réduire les risques de brouil-lage radioélectrique à l'intention des autres utilisa -teurs, il faut choisir le type d'antenne et son gain de sorte que la pui ssance isotrope rayonnée équiva lente (p.i.r.e.) ne dépasse pas l'intensité nécess aire à l'établissement d'une communication satisfaisante. Not Recommended for New Designs

Regulatory Certification, Section 7 AMW037 Datasheet ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | 18 In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation wit h the antenna while this end product is installed and oper- ated. The end user has to be informed that the IC radio- frequency exposure guidelines for an uncontrolled envi- ronment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufac- turer could void the user's authority to operate this equipment. User manuals for transmitters equipped with detach- able antennas shall also contain the following notice in a conspicuous location: Immediately following the above notice, the manufac- turer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required imped- ance for each. Further Information Additional information may be obtained from the Indus- try Canada website at http://www.ic.gc.ca This radio transmitter IC ID 11685A-5B9198 has been approved by Industry Canada to operate with the built-in antenna type, with the maximum permissible gain and required antenna impedance for each an- tenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio IC ID 11685A-5B9198 a été approuvé par Industrie Canada pour fonctionner avec l'antenne installé, et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Not Recommended for New Designs

7.5 Europe

ing integrated into a final product. Opinion has also been issued. AMW037 module must follow CE marking requirements. Note 01 provides guidance on final product CE marking. tance 20cm between the radiator and your body. Table 12. European Compliance Testing

26 July 2016 Eurofins

the essential requirements of the R&TTE Directive.

7.6 Australia

Australian radio regulations do not provide a modular approval policy similar to the United States (FCC) or Can- ada (IC). However, AMW037 module test reports may be used in part to demonstrate compliance in accordance with ACMA Radio communications “Short R ange De- vices” Standard 2004 which references Australia/New Zealand industry standard AS/NZS-4268:2012. AMW037 RF transmitter test reports may be used as part of the product certification and compliance folder. For further information regarding the availability of RF test reports, please contact Zentri via our website at https://www.silabs.com/about-us/contact-us. Further Information Additional information may be obtained from the Aus- tralian Communications and Media Authority website at http://www.acma.gov.au.

7.7 New Zealand

New Zealand radio regulations do not provide a modular approval policy similar to the United States (FCC) or Can- ada (IC). However, AMW037 module test reports may be used in part to demonstrate compliance with the New Zealand “General User Radio License for Short Range De- vices”. New Zealand Radio communications (Radio Standards) Notice 2010 references Australia/New Zea- land industry standard AS/NZS-4268:2012. AMW037 RF transmitter test reports may be used as part of the prod- uct certification and compliance folder. For further infor- mation regarding the availability of RF test reports, please contact Zentri via our website at https://www.silabs.com/about-us/contact-us. Further Information Additional information may be obtained from the New Zealand Radio Spectrum Ministry of Economic Develop- ment website at http://www.rsm.govt.nz. Not Recommended for New Designs

8 Packaging, Handling and Storage, RoHS

8.1 Packaging

Modules are shipped in cut tape, with ESD-safe packaging, or in reels. For package quantity, see section 9, Ordering Information. Reels are shipped enclosed inside a moisture resistant sealed bag. The shelf life of the sealed reel is 12 months at 40°C and <90% Relative Humidity (RH). Please refer to the bag seal date and the following section for handling & storage. Ensure that all modules are managed in accordance with Moisture Sensitive Level 3 (MSL3) per IPC/JEDEC J-STD-20. If reflow is required, AMW037 modules must be baked first, according to Joint Industry Standard J-STD-033C.

8.2 Handling & Storage

MSL3 Sensitive Device! The AMW037 module is a moisture sensitive device rated at Moisture Sensitive Level 3 (MSL3) per IPC/JEDEC J-STD- 20. After opening the moisture sealed storage bag, modules that will be subjected to reflow solder or other high temper- ature processes must be: 1. mounted to a circuit board within 168 hours at factory conditions (≤30°C and <60% RH) OR 2. continuously stored per IPC/JEDEC J-STD-033 Modules that have been exposed to moisture and environmental conditions exceeding packaging and storage condi- tions MUST be baked before mounting according to IPC/JEDEC J-STD-033. Failure to meet packaging and storage conditions will result in irreparable damage to modules during solder reflow.

8.3 RoHS Directive

The AMW037 module is produced according to the RoHS (Restriction of the use of certain Hazardous Substances in electrical and electronic equipment) directive and complies with the directive. Not Recommended for New Designs

8.4 Tape and Reel Specifications

Figure 7 - Tape Specifications Symbol A0 B0 D0 E F P0 P1 P2 T W Specification (mm) 16.30 ±0.10 23.30 ±0.10 1.50 +0.10, -0.00 1.75 ±0.10 20.20 ±0.10 4.00 ±0.10 20.0 ±0.10 2.00 ±0.10 0.30 ±0.05 44.00 ±00.30  All dimensions are in mm unless otherwise specified  The maximum cumulative tolerance is ±0.2mm for 10 sprocket hole pitch  Cambers do not exceed 1.0mm in 250mm length  All dimensions follow EIA-481-2A series definition  Material: PS black  One 22” Reel = 60 meters Not Recommended for New Designs

Packaging, Handling and Storage, RoHS, Section 8 AMW037 Datasheet ADS-MW037-101R • AMW037 Datasheet August 29, 2017 © 2014-2017 Zentri. http://www.zentri.com Page | 23 Figure 8 - Reel Specifications Symbol A B C T W B C T A W Not Recommended for New Designs

9 Ordering Information

You can order AMW037 modules as either cut tape loaded with an unspecified ZentriOS, or as a full reel of 500 units, pre-loaded with either a specific ZentriOS version or a version of your embedded custom application. When you order, refer to the OPN (Orderable Part Number), as described below. For examples, see Table 6 - Ordering Information below.

9.1 Ordering an Unspecified ZentriOS Version

OPN: AMW037 When ordering an unspecified ZentriOS version as cut tape, the OPN is simply AMW037. When the ZentriOS version is unspecified, orders of AMW037 modules ship with whatever versions of ZentriOS are available. The ZentriOS version is not guaranteed to be the same for all items shipped. Cut tape is suita- ble for sampling, evaluation, and pilot builds. Upon delivery, you can update modules individually, via OTA (Over-The-Air update), with a specific firmware version.

9.2 Ordering a Specific ZentriOS-WL Version or a Custom Firmware Version

ZentriOS version OPN: AMW037-x.y.zR Custom firmware version OPN: AMW037-xxxxxxR Volume orders are delivered in reels, as indicated by the R suffix. To ensure consistency, specify an OPN correspond- ing to a specific version. ZentriOS version: the OPN is of the form AMW037-x.y.zR, where x is the major version, y is the minor version and z is the patch version. Custom firmware version: the OPN is of the form AMW037-xxxxxxR, where xxxxxx is a unique ID indicating a specific product version. Zentri ships reels with the product version specified. A custom firmware version includes a specific version of ZentriOS, and additional configuration details. After shipping, individual modules may be updated to later versions of this product only. Table 6 - Ordering Information Order Type Delivery Format Quantity Example OPN Unspecified firmware Cut tape Fewer than 500 units AMW037 Specified ZentriOS version Full reel box 500 units AMW037-1.0.2R Custom firmware Full reel box 500 units AMW37-H35GHJR

9.3 ZentriOS Version History

ZentriOS-WL firmware revision history is available online at: https://docs.zentri.com/zentrios/editions-and-versions#zentrioswl Not Recommended for New Designs

10.1 Revision History

Table 14: Document Revision History Revision Date Change Description ADS-MW037-100R Aug 20, 2016 Initial release ADS-MW037-101R Aug 29, 2017 Added Firmware Features, Dimensions section, new Silicon Labs ordering information, updated European Certification

10.2 Glossary

In most cases, acronyms and abbreviations are defined on first use. A comprehensive list of acronyms and other terms used in Zentri documents are provided on the Zentri website at https://docs.zentri.com/zentri/glossary. Not Recommended for New Designs

11 References

Throughout this data sheet, references to other docu- ments are listed. The following documents provide addi- tional material: 1. IEEE 802.11 Standard Institute of Electrical and Electronics Engineers. http://standards.ieee.org Not Recommended for New Designs

http://www.silabs.com Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701 USA Smart. Connected. Energy-Friendly.Products www.silabs.com/products Quality www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Micrium, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress®, Zentri and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Not Recommended for New Designs

Product Information

AMW37-H35GHJR specifications and overview.

Summary

Embedded Wi-Fi Networking Solution August 29, 2017

Description

Embedded Wi-Fi Networking Solution August 29, 2017

Source title AMW37-H35GHJR Datasheet(PDF) - Silicon Laboratories

Related Parts

More parts from the same family.

Browse manufacturer