AMS001-E03

Silicon Laboratories

Embedded Bluetooth Low Energy Solutions

Manufacturer: Silicon Laboratories

Document: 29 Pages / 1Mb

Request Quote Download Datasheet Read online HTML view

More from Silicon Laboratories Browse A parts

Online Datasheet

Read AMS001-E03 online.

AMS001-E03 SILABS | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 29

Technical content

Datasheet sections

1 General Description
2 Block Diagram
3 Electrical Specifications
3.1 Absolute Maximum Ratings
3.2 Recommended Operating Conditions
3.3 Power Consumption
3.4 Input/Output Pins
3.5 ADC Specifications
4 Bluetooth RF Specifications
4.1 Summary RF Specifications
4.2 Receiver Specifications
4.3 Transmitter Specifications
5 Pinout and Signal Descriptions
5.1 Pinout
5.2 Pin Description
6 Design Guidelines
6.1 Recommended PCB Footprint
6.2 Routing Recommendations
6.3 Soldering Information
6.4 AMS00x Photograph
6.5 Application Examples
6.6 Operation using TruConnect
7 Regulatory Certification
7.1 United States
7.2 Canada
7.3 Europe
7.4 Australia
7.5 New Zealand
8 Packaging, Handling & Storage, RoHS
8.1 Packaging
8.2 Tape and Reel Specifications
8.3 Handling & Storage
8.4 RoHS Directive
9 Ordering Information
10 Revision History & Glossary
10.1 Revision History
10.2 Glossary

AMS00x • Embedded Bluetooth Low Energy Solution ADS-MS00x-107R • Preliminary Data Sheet Page | i ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 Disclaimer While the information provided in this document is be- lieved to be accurate, it is under development and ACKme Networks reserves the right to make changes without further notice to the product de scribed herein to improve reliability, function, or design, and makes no guarantee or warranty concerning the accuracy of said information, nor shall it be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon, s uch information. ACKme Networks makes no warranties of any kind, whether express, im- plied or arising by custom or course of trade or perfor- mance, and specifically disclaims the i mplied warranties of title, non-infringement, merchantability, or fitness for a particular purpose. No part of this document may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photographic, or otherwise, or used as the basis for manufacture or sale of any ite ms without the prior written consent of ACKme Networks. Trademarks ACKme Networks and the ACKme Networks logo are trademarks of ACKme Networks. WICED™ is a trade- mark of Broadcom ® Corporation, Inc. Bluetooth® is a trademark of the Bluetooth SIG. Other trade marks in this document belong to their respective owners. Copyright © 2014-2015 ACKme Networks. All rights reserved. Document Number: ADS-MS00x-107R Release Date: September 14, 2015 Contact http://ack.me/contact About this Data Sheet This document provide s information on the family of AMS00x Bluetooth Low Energy (Bluetooth Smart) mod- ules from ACKme Networks. Organization This data sheet is organized into the following sections:  Features & Applications  General Description, Section 1  Block Diagram, Section 2  Electrical Specifications, Section 3  Bluetooth RF Specifications, Section 4  Pinout and Signal Descriptions, Section 5  Design Guidelines, Section 6  Regulatory Certification, Section 7  Packaging, Handling & Storage, RoHS, Section 8  Ordering Information, Section 9  Revision History & Glossary, Section 11

Features

 Bluetooth Low Energy (Bluetooth Smart) modules fully certified to meet Bluetooth version 4.1.  Integrated 8 Mbit SPI-serial flash supports firm- ware updates and multiple on-board applications  On-board PCB-style antenna  ARM® Cortex™ M3-based microprocessor core  Adaptive Frequency Hopping (AFH)  Programmable RF transmit power control  Operation directly from a battery or mains supply  Small size enables integration into most sensor products and applications  Secure Over -the-Air (OTA) software update using industry-standard AES-128 security  Easily integrated into existing or new products us- ing TruConnect, ACKme’s configurable Bluetooth Low Energy application (pre -installed on every module)  Multiple services including ACKme TruConnect , Beacon, iBeacon, plus more … Interfaces*  A/D converter: 7 channels with 4 modes providing variable resolution (10 -13 ENOBs), sampling rate (5.9-187 kHz) and conversion latency (5-171 µs)  USART: 1 x 4-wire up to 1.5 Mbit/s for general use, 1 x 2-wire for in-circuit programming  SPI: 1 x master, 1 x slave at ≤12 Mbit/s  I2C: 1 x I2C master interface up to 1 MHz  GPIO: Up to 12 GPIOs (overlaid with peripherals), programmable pull -up/pull-down resistors with 16 mA drive strength at 3.3V (2 mA standard).  4 x PWM channels each with a 10 -bit counter clocked at 128 kHz.  Wake-up: Wake from GPIO for ultra -low power operation. *Some interfaces share module pins Operational & Radio  Operational voltage : 1.8V - 3.6V  Operational Temperature Range: -30°C to +85°C  Weight : 0.04 oz (1.2g)  Current consumption @ 3.0V, 25°C - Deep Sleep : 1.65µA (typ.) - Sleep : 12 µA - AMS001  Active Receive : 12.8 mA  Active Transmit : 10.8 mA - AMS002  Active Receive : 26.6 mA  Active Transmit : 22.0 mA  RF Transmit Power: +4 dBm (max.)  Receive Sensitivity : -94 dBm

Applications

 Health & Fitness - Fitness Equipment - Heart rate monitors - Weight scales - Thermometers - Pedometers - Glucose meters - Blood pressure monitoring  Retail - Advertising and Beaconing - Proximity detection - Point-of-sale  Home & Industrial Control and Automation - Appliance control and monitoring - Doors/Window monitoring - Alarms - Wireless cable replacement - Environmental & Energy monitoring - Wireless sensing, remote data logging  Consumer - Toys - Robots Remote controls

1 General Description

The family of AMS00x ‘Bobcat’ modules from ACKme Networks is based on an ultra-low power Bluetooth Low Energy (Bluetooth Smart) SoC from Broadcom Cor- poration. All modules incorporate serial -flash memory and a printed antenna to provide a state -of-the-art ful- ly-certified Bluetooth 4.1 solution. An integrated solution avoids difficult RF layout and enables designers to rapidly embed Bluetooth Low En- ergy into virtually any device. The AMS001 (Low Power) version slashes active power consumption for applications requiring multi -year bat- tery life, while the AMS002 (L ow Cost) version provides the lowest cost solution suitable for price sensitive ap- plications. The modules are 100% footprint compatible. Modules ship with ACKme TruConnect, an easy-to-use application enabling control and configuration via UART-serial and r emote terminal interfaces . TruCon- nect virtually eliminates difficult and time -consuming software development effort and vastly reduce s prod- uct development cycles. With dimensions of just 17.6 x 11.4 mm, a wide tem- perature range, and a n ultra -low power vers ion, the module is suitable for integration into any battery- powered embedded wireless application. The Bluetooth Low Energy SoC from Broadcom is pur- pose-designed to support the entire spectrum of Blue- tooth Smart use cases for medical, home automation, accessory, sensor, retail and wearable market seg- ments. Superior receive sensitivity, a n integrated RF transmit power amplifi er and transmit/receive switch, along with the on -board antenna, provide extended range and full compatibility with all Bluetooth 4.1 de- vices. At the heart of all AMS00x modules is a Bluetooth Low Energy SoC with a high-performance ARM® 32-bit Cor- tex™-M3 core operating at a frequency of 24 MHz. The SoC includes is configured to boot applications stored in the 8 Mbit serial flash memory a vailable on-board the module. The Broadcom BLE SoC supports Adaptive Frequency Hopping. Each module provides an extensive array of I/O and peripheral interfaces. The following interfaces are available, many of which are accessible with I/O multi- plexing and alternate function capabilities: 7 x A/D converter channels  2 x UART interfaces: 1 x 4-wire, 1 x 2-wire  1 x SPI master, 1 x SPI slave bus  1 x I2C interface  Up to 12 x ultra-low power wake input  32kHz crystal interface The module may be powered directly from a battery supply in the range 1. 8-3.6V including 2xAAA, 2xAA, or a single Lithium coin cell. Internal power domains are a utomatically adjusted to minimize power dissipation based on user activity. Var- ious power modes, including an ultra -low power deep sleep mode, are provided to minimize total avera ge power consumption and maximize battery life. Custom factory settings may be saved to a non-erasable area of static memory to enable out -of-the-box custom product configuration and the ability to return products incorporating the module to a known factor y reset state. The module may be woken from deep sleep mode by a level transition on the GPIO assigned for stream mode selection. Other GPIOs may be dynamically allocated for control and status including a BLE connection indicator, serial bus mode control and status indicator, audible alerts and factory reset. An internal 32kHz low -power oscillator is available by default for non -critical timing requirements . Applica- tions requiring an accurate real-time clock may connect an (optional) external 32kHz crystal. All versions of the module have Bluetooth BQB SIG cer- tification, and FCC & IC modular approval for use in the United States and Canada , and CE approval for use in Europe and other countries.

2 Block Diagram

duce active mode power consumption. Figure 1. AMS00x Architecture

8 Mbit

3 Electrical Specifications

3.1 Absolute Maximum Ratings

term reliability of the device. Table 1. Absolute Maximum Voltage Ratings Table 2. Absolute Maximum Environmental Ratings

3.2 Recommended Operating Conditions

limits for extended periods can adversely affect long-term reliability of the device. Table 3. Recommended DC Operating Conditions

Overall performance degrades beyond minimum and maximum supply voltages.
The module may fail to boot if this condition is not met when power is initially applied.

Table 4. Recommended Environmental Conditions

3.3 Power Consumption

consumption in each state, and for each version of the module, is specified in Table 5. Table 5. Power Consumption (3.0V, 25°C)

Requires 10K pullup resistor on module pin 6. See 6.5.1, UART Application for Configuration and Streaming

3.4 Input/Output Pins

All digital I/O pins have a maximum input voltage rating of VSS-0.3V to VDD+0.3V. The maximum supply voltage is 3.63V. Consequently, digital I/O pins are NOT +5V tolerant. Table 6. Digital I/O Pin Levels

At the specified drive current for the pin.

3.5 ADC Specifications

Table 7. ADC Specifications (@ 25°C)

4 Bluetooth RF Specifications

4.1 Summary RF Specifications

Table 8. Summary RF Specifications

4.2 Receiver Specifications

Table 9. Receiver Performance Specifications

4.3 Transmitter Specifications

Table 10. Transmitter Performance Specifications

5 Pinout and Signal Descriptions

5.1 Pinout

A top view of the AMS00x pinout is depicted in Figure 2. mended PCB footprint is provided in Section 6.1. Figure 2. AMS00x Pinout (TOP View – Pins NOT visible from top!)

5.2 Pin Description

Table 11. AMS00x Pin Definitions

1 GND S Ground -

2 PROG_RX I PROG RX -

3 PROG_TX O PROG TX -

6 GPIO_2 I/O USER TX SPI_MOSI (Slave), ADC, GPIO

8 RESET_N I System Reset -

9 GPIO_4 I/O USER_CTS SPI_CLK (Slave), GPIO

10 GPIO_5 I/O USER_RX SPI_CS (Slave), GPIO

AMS00x • Embedded Bluetooth Low Energy Solution Pinout and Signal Descriptions, Section 5 ADS-MS00x-107R • Preliminary Data Sheet Page | 9 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 Pin Name Type1 Primary Function Alternate & Other Function(s)

11 GPIO_6 I/O GPIO SPI_MOSI (Master), FACTORY_RESET3

12 GPIO_7 N/C Reserved4 Reserved. Not available as digital I/O

13 GPIO_8 I/O GPIO SPI_MISO (Master)

14 GPIO_9 I/O GPIO SPI_CLK (Master)

15 GPIO_102 I/O GPIO ADC, PWM

16 GPIO_11 I/O GPIO ADC, PWM

17 GPIO_12 I/O GPIO SPI_CS (Master), ADC

18 GPIO_132 I/O GPIO ADC, PWM, XOSC32_OUT

19 GND S Ground -

20 GPIO_142 I/O GPIO ADC, PWM, XOSC32K_IN

21 VDD S VDD -

Notes: 1. I = Input, O = Output, S = Supply 2. The drive strength of standard GPIOs is 2mA, the drive strength of this GPIO is 16mA. 3. The FACTORY_RESET pin may be moved to a different GPIO, but it may not be de-assigned 4. Connected to SPI serial flash inside the module

6 Design Guidelines

6.1 Recommended PCB Footprint

All dimensions in Figure 3 are in thousands of an inch unless otherwise marked. Figure 3. AMS00x Recommended Footprint (Top)

6.2 Routing Recommendations

than signal or power traces, is strongly advised. the radio receiver and/or transmitter. vias in the shaded rectangle. Measurements are in thousandths of an inch.

6.3 Soldering Information

Figure 4. Recommended solder reflow profile

6.4 AMS00x Photograph

Figure 5. AMS00x Photograph (Top)

6.5 Application Examples

not required, but is recommended for streaming continuous data. Figure 6. Connecting a Host MCU to the AMS001/AMS002 User UART

6.6 Operation using TruConnect

User Settings. This configuration is set by a user and

TruConnect attempts to load the factory settings.

AMS00x • Embedded Bluetooth Low Energy Solution Design Guidelines, Section 6 ADS-MS00x-107R • Preliminary Data Sheet Page | 13 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 2. Factory Settings. Factory configuration provides a way to save a configuration at manufacturing time. Factory settings are saved using the TruConnect command: save factory <BD_ADDR> Save with the lock option to ensure that factory settings cannot be overwritten: save factory <BD_ADDR> lock CAUTION! The factory configuration cannot be changed after saving with the lock option. If no factory configuration is present or it is corrupt- ed, then TruConnect loads the basic compile-time default configuration. 3. Default Settings. The default configuration is a sane set of defaults that are hardcoded in TruCon- nect. Factory Reset The module may be factory reset with a TruConnect command, or by asserting the factory reset pin at bootup. To factory reset via a command, issue: > fac <BD_ADDR> To factory reset via the factory reset GPIO: 1. Identify the GPIO used for factory reset by issu- ing the command to get GPIO usage: get gp u (the factory reset default is GPIO 6). 2. Assert a logic 1 (high) on the pin associated with the factory reset GPIO 3. Assert and de -assert the reset pin to force the module to reboot 4. Wait at least 10 seconds (the status of factory reset is printed to the User UART 5. De-assert the factory reset pin Command and Stream Mode The module boots into serial bus command mode by default and accepts configuration and control com- mands via the User UART. Once the configuration is saved, stream mode may be used to transfer data be- tween the serial interface and a remote device con- nected to the Bluetooth LE wireless interface. To toggle between command mode and stream mode, the GPIO alternate function mode_sel may be used (if config- ured), or to simply transition from command mode to stream mode, use the str command. Once in stream mode, characters received from a host MCU on the seria l interface are automatically transmit- ted to a remotely connected device via the BLE wireless interface, and characters received from a remotely connected device on the BLE wireless interface are seamlessly transmitted on the serial interface to the host MCU. Configuration of the module is also possible using a re- motely connected application, however if the serial in- terface is configured to use command mode, remote applications are forbidden from accessing the com- mand interface. To grant a remote application access to the command interface, the serial interface must first place the module into stream mode to signal that it no longer requires access to the command parser. GPIO Configuration & Usage The default GPIO configuration of the module is shown in the following list, obtained by issuing the TruConnect command sequence get gp u. The User UART, factory reset and I2C pins are configured by default. All other pins are unassigned or reserved. > get gp u ! # Description # 0 i2c_sda # 1 i2c_scl # 2 user_tx # 3 none # 4 none # 5 user_rx # 6 none,factory # 7 reserved # 8 none # 9 none # 10 none # 11 none # 12 none # 13 none # 14 none To configure a GPIO pin for use, the pin must be as- signed a function. A large range of functions is ava ila- ble, please refer to the TruConnect reference guide online (at the following link ) for further information: http://truconnect.ack.me/commands#gfu

7 Regulatory Certification

The AMS00x family of modules has been certified for operation in various regulatory domains. This section outlines certification information specific to the follow- ing countries and regions:  United States  Canada  Europe  Australia  New Zealand Should you require regulatory certification for the AMS00x module in a country or region not listed, please contact your local ACKme Networks sales office or cre- ate a support request via our website at http://ack.me/contact.

7.1 United States

The ACKme Networks AMS -00x module has received Federal Communications Commission (FCC) CFR47 Tele- communications, Part 15 Sub-part C “Intentional Radia- tors” modular approval in accordance with Part 15.212 Modular Transmitter approval. Mo dular approval al- lows the end user to integrate the AMS -00x module into a finished product without obtaining subsequent and separate FCC approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or modifications could void the user’s authority to operate the equipment. The end user must comply with all of the instructions provided by the Grantee which indicate installation and/or oper- ating conditions necessary for compliance. The finished product is required to comply with all ap- plicable FCC equipment authorization, regulations, re- quirements, and equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Sub-part B “Unintentional Radiators”), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for non - transmitter functions on the transmitter module (i.e. Verification, or Declaration of Conformity) (e.g., trans- mitter modules may also contain digital logic functions) as appropriate. Labeling and User Information Requirements The AMS -00x module has been labelled with a unique FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the out- side of the finished product into which the module is installed must also display a label referring to the en- closed module. This e xterior label can use wording as follows: The user manual for the product should include the fol- lowing statement: Contains FCC ID: 2ABPY-BB4EA - Model No: AMS001 Contains FCC ID: 2ABPY-0D06E - Model No: AMS002 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un- desired operation. This equipment has been tested and found to com - ply with the limits for a Class B digital device, pursu- ant to part 15 of the FCC Rules. These limits are de- signed to provide reasonable protec tion against harmful interference in a residential installation. This equipment generates, uses and can radiate ra- dio frequency energy and if not installed and used in accordance with the instructions, may cause harm- ful interference to radio communications . However, there is no guarantee that interference will not oc- cur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equip- ment and receiver.  Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-107R • Preliminary Data Sheet Page | 15 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engi- neering and Technology (OET) Laboratory Division Knowledge Database (KDB) at the following website: https://apps.fcc.gov/oetcf/kdb/index.cfm RF Exposure All transmitters reg ulated by FCC must comply with RF exposure requirements. OET Bulletin 65, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, provides assis- tance in determining whether proposed or existing transmitting f acilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal Communications Com- mission (FCC). The bulletin offers guidelines and sugges- tions for evaluating compliance. If appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels and by providing users with information concerning minimum separation distances from transmitting structures and proper installation of antennas. The following statement must be included as a CAU- TION statement in manuals and OEM products to alert users of FCC RF exposure compliance: If the AMS-00x module is used in a portable application (i.e., the antenna is less than 20 cm from persons dur- ing o peration), the integrator is responsible for per- forming Specific Absorption Rate (SAR) testing in ac- cordance with FCC rules 2.1091. External Antenna Modular approval in the United States is permitted with the use of the integrated antenna ONLY. If an exter nal antenna is used with the AMS -00x module, additional testing of the end product is needed to meet FCC re- quirements. Further Information Additional information regarding FCC certification and use of the AMS -00x module in the United States is available from the following sources.  Federal Communications Commission (FCC) http://www.fcc.gov.au  FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) http://apps.fcc.gov/oetcf/kdb/index.cfm

7.2 Canada

The AMS-00x module has been certified for use in Can- ada under Industry Canada (IC) Radio Standards Specifi- cation (RSS) RSS -210 and RSSGen. Modular approval permits the installation of a modul e in a host device without the need to recertify the device. Labeling and User Information Requirements Labeling Requirements for the Host Device (from Sec- tion 3.2.1, RSS -Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words “Contains transmit- ter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows: User Manual Notice for License -Exempt Radio Appa- ratus (from Section 7.1.3 RSS -Gen, Issue 3, December 2010): User manuals for license -exempt radio appa- To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Contains transmitter module IC: 11685A-0D06E

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-107R • Preliminary Data Sheet Page | 16 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 ratus shall contain the following or equivalent notice in a conspicuous location in the user manual or alterna- tively on the device or both: Transmitter Antenna Notification (from Section 7.1.2 RSS-Gen, Issue 3, December 2010): User manuals for transmitters shall display the following notice in a con- spicuous location: The above notice may be affixed to the device instead of displayed in the user manual. User manuals for transmitters equipped with detach - able antennas shall also contain the following notice in a conspicuous location: Immediately following the above notice, the manufac- turer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible anten na gain (in dBi) and required imped- ance for each. External Antenna Types Transmitter Antenna (from Section 7.1.2 RSS-Gen, Issue 3, December 2010): The AMS-00x module can only be operated with the on- board antenna with which it was approved without ad- ditional testing. If an external antenna is used with the AMS -00x mod- ule, additional testing of the end product is needed to meet IC requirements as described in the previous sec- tion. Further Information Additional information may be obtained from the In- dustry Canada website at http://www.ic.gc.ca This device complies with Industry Canada license - exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this de vice must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Indus- trie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux de ux onditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appa- reil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Can ada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Can - ada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Indus- trie Canada. Dans le but de réduire les risques de brouil-lage radioélectrique à l'intention des autres utilisa-teurs, il faut choisir le type d'antenne et son gain de sorte que la pui ssance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter (identify the device by certifi- cation number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'an- tenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

7.3 Europe

The AMS -00x module is an R&TTE Directive assessed radio module that is CE marked and has been manufac- tured and tested with the intention of being integrated into a final product. The AMS -00x module has been tested to R&TTE Di- rective 1999/5/EC Essential Requirements for Health and Safety Article 3.1(a), Electromagnetic Compatibility (EMC) Article 3.1(b), and Radio Article 3.2 and the re- sults are summarized in Table 12. A Notified Body Opin- ion has also been issued. All AMS -00x test reports are available on the ACKme Networks website at http://ack.me/contact. The R&TTE Compliance Association provides guidance on modular devic es in the document titled Technical Guidance Note 01 available on the website at http://www.rtteca.com/html/download_area.htm. Labeling and User Information Requirements The label on the fina l product which contains the AMS-00x module must follow CE marking requirements. The R&TTE Compliance Association Technical Guidance Note 01 provides guidance on final product CE marking External Antenna Requirements From R&TTE Compliance Association docu ment Tech- nical Guidance Note 01: Provided the integrator installing an assessed radio module with an integral or specific antenna and in- stalled in conformance with the radio module manufac- turer’s installation instructions requires no further evaluation under Article 3.2 of the R&TTE Directive and does not require further involvement of an R&TTE Di- rective Notified Body for the final product. [ Section 2.2.4] The European Compliance Testing listed in Table 12 was performed using the AMS-00x on-board antenna. Further Information A document that can be used as a starting point in un- derstanding the use of Short Range Devices (SRD) in Europe is the European Radio Communications Com- mittee (ERC) Recommendation 70 -03 E, which can be downloaded from the European Radio Communications Office (ERO) at: http://www.ero.dk. Further information may be obtained from the follow- ing websites:  Radio and Telecommunications Terminal Equip- ment (R&TTE) http://ec.europa.eu/enterprise/rtte/index_en.htm  European Conference of Postal and Telecommuni- cations Administrations (CEPT) http://www.cept.org  European Telecommunications Standards Institute (ETSI) http://www.etsi.org  European Radio Communications Office (ERO) http://www.ero.dk  The Radio and Telecommunications Terminal Equipment Compliance Association (R&TTE CA) http://www.rtteca.com/ NOTE: To maintain conformance to the testing listed in Table 12, the module shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. When integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essential requirements of the R&TTE Directive.

Table 12. European Compliance Testing

7.4 Australia

our website at http://ack.me/contact. Australian regulatory requirements.

7.5 New Zealand

New Zealand radio regulations do not provide a modu- lar approval policy similar to the United States (FCC) and Canada (IC). However, AMS -00x module test re- ports may be used in part to demonstrate compliance with the New Zealand “General User Radio License for Short Range Devices”. New Zealand Radio communica- tions (Radio Standards) Notice 2010 references Austral- ia/New Zealand industry standard AS/NZS -4268:2012. AMS-00x RF transmitter test reports may be used as part of the product certification and compliance folder. For further information regarding the availability of RF test reports, please contact ACKme Networks via our website at http://ack.me/contact. External Antenna Requirements The compliance test reports provided in Table 12 were performed using the AMS -00x on-board antenna. If an external antenna is used with the AMS -00x module, additional testing of the end product is needed to meet New Zealand regulatory requirements. Further Information Additional information may be obtained from the New Zealand Radio Spectrum Ministry of Economic Devel- opment website at http://www.rsm.govt.nz.

AMS00x • Embedded Bluetooth Low Energy Solution Packaging, Handling & Storage, RoHS, Section 8 ADS-MS00x-107R • Preliminary Data Sheet Page | 20 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015

8 Packaging, Handling & Storage, RoHS

8.1 Packaging

AMS00x modules are shipped in an ESD bag. AMS00x modules are also available in reels each containing 1000 modules. Reels are shipped in an ESD and moisture resistant sealed bag. The shelf life of the sealed bag is 12 months at 40°C and <90% Relative H umidity (RH). Please refer to the bag seal date.

8.2 Tape and Reel Specifications

Figure 7 - Tape Specifications Symbol A0 B0 D0 E F K0 Symbol P P0 P2 T W  Tape material : black PS material, in line with ROHS environmental management substances  Tape thickness: 0.3 mm ± 0.05 mm  Tape width: 32mm (1.3")  Protection zone: black PS material  Distance between chain hole centers within the range of ± 0.2 mm of cumulative error  Anti-camber at 1 mm / 250 mm  All dimensions in line with the requirements of EIA-481-D

AMS00x • Embedded Bluetooth Low Energy Solution Packaging, Handling & Storage, RoHS, Section 8 ADS-MS00x-107R • Preliminary Data Sheet Page | 21 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015 Figure 8 - Reel Specifications Symbol A B C1 D E H T

AMS00x • Embedded Bluetooth Low Energy Solution Packaging, Handling & Storage, RoHS, Section 8 ADS-MS00x-107R • Preliminary Data Sheet Page | 22 ©2014-2015 ACKme Networks. http://ack.me September 14, 2015

8.3 Handling & Storage

MSL3 Sensitive Device! AMS00x modules are moisture sensi tive device s rated at Moisture Sensitive Level 3 (MSL3) per IPC/JEDEC J-STD-20. After opening the moisture sealed storage bag, mod- ules that will be subjected to reflow solder or other high temperature processes must be: 1. mounted to a circuit board within 168 hours at factory conditions (≤30°C and <60% RH) OR 2. continuously stored per IPC/JEDEC J-STD-033 Modules that have been exposed to moisture and envi- ronmental conditions exceeding packaging and storage conditions MUST be baked before mounting according to IPC/JEDEC J-STD-033. Failure to meet packaging and storage conditions will result in irreparable damage to modules during solder reflow.

8.4 RoHS Directive

Each AMS00x module is produced according to the RoHS (Restr iction of the use of certain Hazardous Substances in electrical and electronic equipment) di- rective and complies with the directive.

9 Ordering Information

AMS00x modules are available individually or in a reel of 1000 units as described in the tables below. Table 13. AMS001 Ordering Information AMS001/R A single reel containing 1000 x AMS001 modules, each with TruConnect pre-installed. The entire reel is packaged in an ESD and MSL3-rated moisture sensitive bag. Table 14. AMS002 Ordering Information AMS002/R A single reel containing 1000 x AMS002 modules, each with TruConnect pre-installed. The entire reel is packaged in an ESD and MSL3-rated moisture sensitive bag.

10.1 Revision History

Table 15: Document Revision History Revision Date Change Description ADS-MS00x-100R 10-Nov-2014 Initial version ADS-MS00x-101R 7-Jan-2015 Note minimum boot voltage Add packaging section ADS-MS00x-102R 2-Feb-2015 Note pull-up requirement and minimum deep sleep current ADS-MS00x-103R 2-Feb-2015 Finalized AMS002 CE regulatory information for AMS002 ADS-MS00x-104R 8-Apr-2015 Added limits for IO pins Finalized AMS001 regulatory information ADS-MW00x-105R 9-Jun-2015 Updated GPIO and pin definitions in Pin and Signal Descriptions ADS-MW00x-106R 28-Aug-2015 Added maximum voltage details for Input and Output Pins Added vias diagram to Routing Recommendations Added tape and reel documentation. Removed tray packaging details. ADS-MW00x-107R 14-Sep-2015 Added Adaptive Frequency Hopping to features and description.

10.2 Glossary

In most cases, acronyms and abbreviations are defined on first use. A comprehensive list of acronyms and other terms used in ACKme Networks documents are provided on the ACKme Networks website at http://ack.me/FAQs/Glossary.

AMS00x • Embedded Bluetooth Low Energy Solution ACKme reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by ACKme is believed to be accurate and reliable. However, ACKme does not assume any liability arising out of the application or use of this information, nor the application or use of any product described herein, neither does it convey an y license under its patent rights nor the rights of others. ACKme Networks

20 North Santa Cruz Ave

Product Information

AMS001-E03 specifications and overview.

Summary

Embedded Bluetooth Low Energy Solutions

Description

Embedded Bluetooth Low Energy Solutions

Source title AMS001-E03 Datasheet(PDF) - Silicon Laboratories

Related Parts

More parts from the same family.

Browse manufacturer