HM8113 HMSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • Wide 4V to 18V Operating Input Range
  • 3A Continuous Output Current
  • 500KHz Switching Frequency
  • Short Protection with Hiccup-Mode
  • Built-in Over Current Limit
  • Built-in Over V oltage Protection
  • Internal Power-Save Mode (PFM/PWM)
  • Internal Soft-Start
  • 70mΩ/50mΩ Low RDS(ON) Internal Power MOSFETs
  • Output Adjustable from 0.6V
  • No Schottky Diode Required
  • Integrated internal compensation
  • Thermal Shutdown
  • Available in SOT23-6 Package
  • -40°C to +85°C Temperature Range

Applications

  • Digital Set-top Box (STB)
  • Tablet Personal Computer (Pad)
  • Flat-Panel Television and Monitor
  • Wi-Fi Router / AP
  • Digital Video Recorder (DVR)
  • Portable Media Player (PMP)
  • Cable Modem / XDSL
  • General Purposes General Description The +0 is a high frequency, synchronous, rectified, step-down, switch-mode converter with internal power MOSFETs. It offers a very compact solution to achieve a 4 A peak output current over a wide input supply range, with excellent load and line regulation. The +0 requires a minimal number of readily available, external components and is available in a space saving SOT23-6 package. Typical Application Circuit COUTR1 CIN IN SW EN FB GND VIN VOUT BS ON/ OFF CFF COUTR1 CIN IN SW EN FB GND VIN VOUT BS ON/ OFF CFF Basic Application Circuit

18V 3A 500KHz Synchronous Step-Down Regulator Pin Description Pin Configuration SW EN IN BS FB GND SW EN IN BS FB GND TOP VIEW SOT23-6 SW EN IN BS FB GND TOP VIEW SOT23-6 Top Marking: DBYLL (device code: DB, Y=year code, LL= lot number code) Pin Description Pin Name Function 1 BS Bootstrap. A capacitor connected between SW and BST pins is required to form a floating supply across the high-side switch driver.

2 GND GROUND Pin

3 FB Adjustable V ersion Feedback input. Connect FB to the center point of the external resistor divider 4 EN Drive this pin to a logic-high to enable the IC. Drive to a logic-low to disable the IC and enter micro-power shutdown mode.

5 IN Power Supply Pin

6 SW Switching Pin

Marking Part No. Model Description Package MOQ DBYLL 70301041 +0 +0 B uck, 4-18V , 3A, 500KHz, VFB 0.6V , SOT23-6 SOT23-6 3000PCS HM8113

18V 3A 500KHz Synchronous Step-Down Regulator Absolute Maximum Ratings VIN, EN, V oltage …………………... -0.3V to 21V Operating Temperature Range …...-40°C to +85°C Lead Temperature (Soldering, 10s) ……... +300°C ESD (Human Body Made) HMB…………….2KV Storage Temperature Range ………………. -65°C to 150°C Note1: Exceeding these ratings may damage the device. Note2: The device is not guaranteed to function outside of its operating conditions.

Electrical Characteristics

Parameter Test Conditions Min Typ. Max Unit Input V oltage Range 4 18 V Supply Current in Operation VEN=3.0V , VFB=1.1V 0.4 0.6 mA Supply Current in Shutdown VEN =0 or EN = GND 4 uA Regulated Feedback V oltage TA = 25°C, 4V≤VIN ≤18V 0.588 0.6 0.612 V High-Side Switch On-Resistance 70 mΩ Low-Side Switch On-Resistance 50 mΩ High-Side Switch Leakage Current VEN=0V , VSW=0V 0 10 uA Upper Switch Current Limit Minimum Duty Cycle 4 A Oscillation Frequency 0.5 MHz Maximum Duty Cycle VFB=0.6V 92 % Minimum On-Time 60 nS Minimum Off-Time 90 nS Soft Start 1.2 mS Thermal Shutdown 160 ℃ Thermal Hysteresis 20 ℃ Note3: MOSFET on-resistance specifications are guaranteed by correlation to wafer level measurements. Note4: Thermal shutdown specifications are guaranteed by correlation to the design and characteristics analysis. HM8113

Figure 2. HM8113 Block Diagram network minimizes the external component counts and simplifies the control loop design. higher than REF, REF regains control. The SS time is internally max to 1.2ms.

18V 3A 500KHz Synchronous Step-Down Regulator current is greatly reduced to alleviate the thermal issue and to protect the regulator. The HM8113 exits the hiccup mode once the over current condition is removed. Startup and Shutdown If both VIN and EN are higher than their appropriate thresholds, the chip starts. The reference block starts first, generating stable reference voltage and currents, and then the internal regulator is enabled. The regulator provides stable supply for the remaining circuitries. Three events can shut down the chip: EN low, VIN low and thermal shutdown. In the shutdown procedure, the signaling path is first blocked to avoid any fault triggering. The comp voltage and the internal supply rail are then pulled down. The floating driver is not subject to this shutdown command. Applications Information Setting the Output Voltage HM8113 require an input capacitor, an output capacitor and an inductor. These components are critical to the performance of the device. HM8113 are internally compensated and do not require external components to achieve stable operation. The output voltage can be programmed by resistor divider. 𝑉𝑂𝑈𝑇 = 𝑉𝐹𝐵×𝑅1+𝑅2 VOUT R1 R2 L1MIN L1TYP L1MAX CIN COUT 1V 6.7KΩ 10KΩ 2.2μH 2.2μH 4.7μH 20-47uF 20-68uF 1.2V 10KΩ 10KΩ 2.2μH 2.2μH 4.7μH 20-47uF 20-68uF 1.5V 15KΩ 10KΩ 2.2μH 2.2μH 4.7μH 20-47uF 20-68uF 3.3V 45KΩ 10KΩ 3.3μH 3.3μH 4.7μH 20-47uF 20-68uF Selecting the Inductor The recommended inductor values are shown in the Application Diagram. It is important to guarantee the inductor core does not saturate during any foreseeable operational situation. The inductor should be rated to handle the peak load current plus the ripple current: Care should be taken when reviewing the different saturation current ratings that are specified by different manufacturers. Saturation current ratings are typically specified at 25°C, so ratings at maximum ambient temperature of the application should be requested from the manufacturer. 𝐿 =𝑉𝑂𝑈𝑇×(𝑉𝐼𝑁 −𝑉𝑂𝑈𝑇) 𝑉𝐼𝑁×∆𝐼𝐿×𝐹𝑂𝑆𝐶 Where ΔIL is the inductor ripple current. Choose inductor ripple current to be approximately 30% if the maximum load current. The maximum inductor peak current is: 𝐼𝐿(𝑀𝐴𝑋) = 𝐼𝐿𝑂𝐴𝐷 +∆𝐼𝐿 HM8113

18V 3A 500KHz Synchronous Step-Down Regulator Under light load conditions below 100mA, larger inductance is recommended for improved efficiency. Selecting the Output Capacitor Special attention should be paid when selecting these components. The DC bias of these capacitors can result in a capacitance value that falls below the minimum value given in the recommended capacitor specifications table. The ceramic capacitor’s actual capacitance can vary with temperature. The capacitor type X7R, which operates over a temperature range of −55°C to +125°C, will only vary the capacitance to within ±15%. The capacitor type X5R has a similar tolerance over a reduced temperature range of −55°C to +85°C. Many large value ceramic capacitors, larger than 1uF are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop by more than 50% as the temperature varies from 25°C to 85°C. Therefore X5R or X7R is recommended over Z5U and Y5V in applications where the ambient temperature will change significantly above or below 25°C. Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more expensive when comparing equivalent capacitance and voltage ratings in the 0.47uF to 44uF range. Another important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum will increase about 2:1 as the temperature goes from 25°C down to −40°C, so some guard band must be allowed. PC Board Layout Consideration PCB layout is very important to achieve stable operation. It is highly recommended to duplicate EVB layout for optimum performance. If change is necessary, please follow these guidelines for reference. 1. Keep the path of switching current short and minimize the loop area formed by Input capacitor, high-side MOSFET and low-side MOSFET. 2. Bypass ceramic capacitors are suggested to be put close to the Vin Pin. 3. Ensure all feedback connections are short and direct. Place the feedback resistors and compensation components as close to the chip as possible. 4. VOUT, SW away from sensitive analog areas such as FB. 5. Connect IN, SW, and especially GND respectively to a large copper area to cool the chip to improve thermal performance and long-term reliability. HM8113

18V 3A 500KHz Synchronous Step-Down Regulator Package Description TOP VIEW RECO MMENDED PAD LAYOUT FRO NT VIEW SIDE VIEW AAAAA 2.80 3.00 1.50 1.70 2.60 3.00 PIN EXA MPLE TOP MARK 1.20 TYP 0.60 TYP 0.95 BSC 2.60 TYP 0.90 1.30 0.30 0.50 0.95 BSC

1.45 MAX

0.00 0.15 SEA TING PLANE 0.09 0.20 SOT23-6 GAU GE PLANE

0.25 BSC

0.30 0.550°~8° Note: 1. All dimensions are in millimeters. 2. Package length does not include mold flash, protrusion or gate burr. 3. Package width does not include flash or protrusion. 4. Lead coplanarity (bottom of leads after forming) shall be 0.10 millimeters max. 5. Pin 1 is lower left pin when reading top mark from left to right. HM8113