615 NYLENE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 1
Technical content
NYLENE USA NYLENE CANADA ULC. ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities en 1421 Hwy 136 West 200 McNab Street Product is manufactured in Henderson, KY one) Nylene Henderson, Kentucky 42420 Arnprior, Ontario K7S 3P2 Web: www.nylene.com | Email: info@nylene.com Phone: 270-826-7641 Phone: 613-623-3191 TDS Ref ID: 1531 Toll-free: 800-626-7050 Toll-free: 800-267-7394 Date Updated October 11, 2024 Nylene® 615 Technical Data Sheet Resin Type: * Nylon 6 tesin Type: yion Processing Method{(s): Description: _ * Nylon-6 extrusion grade suitable for coating and film co-extrusion applications * Extrusion * Meets the requirements of FDA regulation for direct food contact * Nylene 615 does not absorb food odors Additives/Modifiers: Properties ASTMI/ISO Procedure Unit English sl * FDA Food Contact Physical Specific Gravity D792 nla 193 1 Form(s)/Color(s): . * Pellets Mechanical Tensile Strength @ Yield D638 si (MPa 5480 38 ane psi (MP2) Features: r Tensil h i (MP. Ultimate Tensile Strengtt D638 psi (MPa) 8650 60 « Excellent melt stablity and strength Elongation D638 % 290 = Mid RV - * Resistance to abrasion Secant Modulus Deez psi (MPa) 95000 652 * Superior grease resistance Thermal * Superior toughness Melt Point 03418 °F (°C) 428 220 Approvals & Recognition: Film "Direct Food Contact: FDA 21 CFR Elmendorf Tear D192 Ibf (af) 0123 56 1771500 End Uses: Notes: Testing conducted on dry-as-molded specimens at 73°F (22.8°C} * Extrusion = Fiber i iderati it ‘ * Pack: Recommended Processing Considerations: Med Viscosity Extrusion ackeging ees ooo © Blown Film * Cast Film (anti-static) Zone °F(C*) —_ Residence Time: Screw should not be left idle for more than 3-4 minutes " Extrusion Coating for Paper Feed 450-470 (232-243) specs in the melt. * Food Packaging Transition 470-490 (243-254) _Regrind Level: Typically, up to 25% is recommended but higher levels are " Fresh & Processed ‘ Meat Packaging 7 : Possible with little or no effect on flow and finish. Metering 480-500 (249-260) * Juice Packaging/Mik Drying Temperature: Although Nylene resins are packaged and delivered Die 480-500 (249-260) ying em oy panes Cartons in a low moisture state, it is good material handling practice to use a » Stand Up Packaging Melt Temp. 480-500 (249-260) hopper dryer to maintain dryness. Should pre-drying be necessary, use for Barrier Strenath settings of 180 °F (82.2°C) air at dew point of -40 at a rate of 1 cu. ft. / hour . 9 per pound of resin and a residence time of 2-4 hours. Plastic Containers Line Rate pph-rpm * Single Layer/Multi Layer Film Cooling ana Sizing: White both air and water can be used as the cooling 22" extruder 15-19 medium, air is preferred. The use of air allows additional time for sizing and 12 reduces residual stress. This aids in reducing warpage, especially in Disclaimer 3?" extruder 35-45 profiles with varying wall sections. If water is used, heat the first section to _Nylene does not guarantee the accuracy of 42" extruder 6.5-7.5 above 100 °F (38°C) to reduce quenching and residual stress. this information or the suitability of this Die Design: Draw down of 30% is typical for all dimensions except wall product for any given application or usage thickness situation. These values are based on test shoul Land length: should be around 10x wall thickness. specimens and should not be used to establish specification limits or fabricate tooling.