609 NYLENE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
NYLENE USA NYLENE CANADA ULC. ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities en 1421 Hwy 136 West 200 McNab Street Product is manufactured in Henderson, KY one) Nylene Henderson, Kentucky 42420 Arnprior, Ontario K7S 3P2 Web: www.nylene.com | Email: info@nylene.com Phone: 270-826-7641 Phone: 613-623-3191 TDS Ref ID: 1520 Toll-free: 800-626-7050 Toll-free: 800-267-7394 Date Updated September 30, 2024 Nylene® 609 Technical Data Sheet Resin Type: * Nylon 6 tesin Type: ryion Processing Method{(s): Description: * Nylon 6, high viscosity, extrusion grade recommended for practically all types of extrusion including * Extrusion profile, film, and extrusion coating * Film * Can also be used for blow molding applications * Blown Film * Optimum processing conditions should permit for a melt temperature of 550 - 575°F (289 - 301°C) at * Coating the die. * Tubing & Profile = Especially recommended for flexible packaging where as a film or coating it is used for the outside layer * Pipe Profiles in multi-ply film constructions * Rods & Other Profiles Properties ASTM/ISO Unit English si Form(s)/Color(s): Procedure ee * Pellets Physical Specific Gravity p792 nla 112 1 Features: Relative Viscosity D789 Formic Acid nla 200 * Excellent melt flow . Sr th Water Absorption 570 % W Good melt strengt! "High RV Mechanical * Single layer nylon system Elongation D638 (77°C) % 140 Approvals & Recognition: Flexural Modulus D790 psi (MPa) 380000 2,620 "Direct Food Contact: FDA 21 CFR Flexural Stiffness 790 psi (MPa) 260000 1,793 4771500 Notched Izod @ 23°C D256 ft-Ib/in (u/m) 1 53 ‘Automotive OEM: Specs & Colors: Rockwell Hardness RScale - 118 "Chrysler, Fiat, Peugeot, FCA Group Tensile Strength D638 psi (MPa) m1000 76 MS-DB41 CPN 5165 Thermal End Uses: Heat Deflection @ 264 psi (1.8 MPa) D648 °F (°C) 60 140 * Extrusion Melt Point D3418 F (°C) 430 221 * Extrusion Coating * Pipe * Profile Extrusion Notes: Testing conducted on dry-as-molded specimens at 73°F (22.8°C} * Rod Stock * Tubing * Packaging Recommended Processing Considerations: High Viscosity Extrusion = Blown Film Zone °F(C°) Residence Time: Screw should not be left idle for more than 3-4 minutes Disctaimer Feed 420-445 (216-220) ith meltin the barrel. Excess residence willbe visible as black carbon Nylene does not guarantee the accuracy of eet ~ : specs in the melt. this information or the suitability of this Transition 435-465 (224-241) Regrind Level: Typically, up to 25% is recommended but higher levels are Product for any given application or usage situation. These values are based on test Metering 445-475 (229-246) Possible with little or no effect on flow and finish, . specimens and should not be used to Drying Temperature: Although Nylene resins are packaged and delivered Die 445-475 (229-246) establish specification limits or fabricate in a low moisture state, it is good material handling practice to use a tooling Melt Temp. 455-489 (235-254) hopper dryer to maintain dryness. Should pre-drying be necessary, use settings of 180 °F (82.2°C) air at dew point of -40 at a rate of 1 cu. ft. / hour per pound of resin and a residence time of 2-4 hours. Line Rate pph-rpm Cooling ana Sizing: While both air and water can be used as the cooling 22" extruder 15-19 medium, air is preferred. The use of air allows additional time for sizing and 312" extrud 35-45 “educes residual stress. This alds in reducing warpage, especially in extruder as profiles with varying wall sections. If water is used, heat the first section to V2" extruder 65-75 above 100 °F (38°C) to reduce quenching and residual stress
Die Design: Draw down of 30% is typical for all dimensions except wall thickness. Land length: should be around 10x wall thickness.