607 NYLENE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
NYLENE USA NYLENE CANADA ULC. ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities >> 1421 Hwy 136 West 200 McNab Street Product is manufactured in Henderson, KY & oO Nylene Henderson, Kentucky 42420 Arnprior, Ontario K7S 3P2 Web: www.nylene.com | Email: info@nylene.com OP Phone: 270-826-7641 Phone: 613-623-3191 TDS Ref ID: 1517 Toll-free: 800-626-7050 Toll-free: 800-267-7394 Date Updated September 20, 2024 Nylene® 607 Technical Data Sheet Resin Type: * Nylon 6 tesin Type: ryion Processing Method{(s): Description: — * Very high viscosity extrusion resin having an ASTM relative viscosity of 800. * Extrusion * Particularly recommended for the extrusion of thick slab, large rod stock, and large complex profiles. * Optimum processing conditions should permit for a melt temperature of 550 - 575°F (289 - 301°C) at the die. Additives/Modifiers: * Properties promote dimensional control for extrusion of pipe, tubing, film, and sheet. * Lubricated Properties ASTM/ISO Unit English sI pi If a! Form(s)/Color(s): Procedure / EE * Pellets Physical Specific Gravity 0792 nla 114 1 Features: Water Absorption Ds70 % 20 * Excellent durability Menteanieal = Excellent properties = Excellent structural strength Tensile Strength D638 psi (MPa) 12300 85 * Good draw-down Flexural Modulus D790 psi (MPa) 400000 2,758 * Good melt strength Flexural Strength D790 psi (MPa) 15500 107 Automotive OEM: Specs & Colors: Notched Izod @ 23°C D256 ft-lb/in (u/m) 09 48 General Motors Corporation Thermal GM7001M PAG (A4, DC1130, E60, F219, G20, K650, M240, R35, DTUL @ 66 psi/0.45 MPa D648 F (°C) 367 186 SAN60) DTUL @ 264 psi/1.82 MPa D648 °F (°C) 149 65 End Uses: * Extrusion Notes: Testing conducted on dry-as-molded specimens at 73°F (22.8°C} * Large Complex Profiles * Large Rod Stock is iderati ah Viecosit i * Pipe Recommended Processing Considerations: High Viscosity Extrusion © Thick Slab "Tubing Zone °F(C*) Residence Time: Screw should not be left idle for more than 3-4 minutes * Packaging ea apo-ags (nie-p70)_ With-meltin the barre. Excess residence willbe visible as black carbon * Blown Film ee "445 (216-229) specs in the melt. * Film ti * Sheet Transition 435-465 (224-241) _Regrind Level: Typically, up to 25% is recommended but higher levels are Metering 445-475 (229-246) Possible with little or no effect on flow and finish. vise bh 4445-475 (229-246) DYving Temperature: Although Nylene resins are packaged and delivered isclaimer e . - in a low moisture state, it is good material handling practice to use a Nylene does not guarantee the accuracy of Melt Temp. 455-489 (235-254) hopper dryer to maintain dryness. Should pre-drying be necessary, use this information or the suitability of this settings of 180 °F (82.2°C) air at dew point of -40 at a rate of 1cu. ft./hour _ product for any given application or usage , per pound of resin and a residence time of 2-4 hours. situation. These values are based on test Line Rate pph-rpm ————_ Coooting and Sizing: While both air and water can be used as the cooling specimens and should not be used to 22" extruder 15-19 medium, air is preferred. The use of air allows additional time for sizing and _@tablish specification limits or fabricate va. reduces residual stress. This aids in reducing warpage, especially in tooling. 32" extruder 35-45 profiles with varying wall sections. If water is used, heat the first section to V2" extruder 65-75 above 100 °F (38°C) to reduce quenching and residual stress. Die Design: Draw down of 30% is typical for all dimensions except wall thickness. Land length: should be around 10x wall thickness.