EUK-075SXXXDT INVENTRONICS
Document overview
- Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
- PDF pages: 13
Technical content
Features
Description
The EUK-075SxxxDT(TT) series is a 75W, constant-current, programmable IP67 LED driver that operates from 90-305 Vac input with excellent power factor. It is created for many lighting applications including low bay, tunnel and street. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input surge, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range Full-Power Current Range (1) Default Output Current Input Voltage Range(2) Output Voltage Range Max. Output Power Typical Efficiency (3) Power Factor Model Number 120Vac 220Vac 45-700mA 450-700mA 530 mA 90~305 Vac/ 127~250Vdc 54~167Vdc 75 W 90.5% 0.98 0.96 EUK-075S070DT(TT) 70-1050mA 700-1050mA 700 mA 90~305 Vac/ 127~250 Vdc 36~107Vdc 75 W 90.0% 0.98 0.96 EUK-075S105DT(TT) (4) 119-1750mA 1190-1750mA 1400 mA 90~305 Vac/ 127~250 Vdc 22 ~ 63Vdc 75 W 90.0% 0.98 0.96 EUK-075S175DT(TT) (4) 190-2800mA 1900-2800mA 2100 mA 90~305 Vac/ 127~250Vdc 14 ~ 39Vdc 75 W 88.5% 0.98 0.96 EUK-075S280DT(TT) (5) Notes: (1) Output current range with constant power at 75W (2) Certified voltage range: UL, FCC 100-277Vac or 127-250Vdc; otherwise 100-240Vac or 127-250Vdc (except KS) (3) Measured at 100% load and 220Vac input (see below “General Specifications” for details). (4) SELV Output. (5) Class 2 & SELV Output. High Efficiency (Up to 90.5%) Full Power at Wide Output Current Range (Constant Power) 0-10V/10V PWM Dimmable (DT models)
3 Timer Modes Dimmable (TT models)
Input Surge Protection: 6kV line-line, 10kV line-earth All-Around Protection: OVP, SCP, OTP Waterproof (IP67) and UL Dry / Damp / Wet Location Class 2 & SELV Output TYPE HL, for use in a Class I, Division 2 hazardous (Classified) location 5 Years Warranty
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com I-V Operating Area EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) Input Specifications Parameter Min. Typ. Max. Notes Input Voltage 90 Vac - 305 Vac 127~250Vdc Input Frequency 47 Hz - 63 Hz Leakage Current - - 0.75 MIU UL8750; 277Vac/ 60Hz - - 0.70 mA IEC60598-1; 240Vac/ 60Hz Input AC Current - - 0.8 A Measured at 100% load and 120 Vac input. - - 0.40 A Measured at 100% load and 220 Vac input. Inrush Current(I2t) - 0.25A 2s At 220Vac input, 25C cold start, duration=112 us, 10%Ipk-10%Ipk. See Inrush Current Waveform for the details.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Input Specifications (Continued) Parameter Min. Typ. Max. Notes PF 0.9 - - At 100-277Vac, 50-60Hz, 75%-100% Load THD - 8% - At 220-240Vac, 50-60Hz, 80%-100%Load (60-75W) Output Specifications Parameter Min. Typ. Max. Notes Output Current Tolerance -5%Ioset - 5%Ioset 100% load Output Current Setting(Ioset) Range EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) 45 mA 70 mA 119 mA 190 mA 700 mA 1050 mA 1750 mA 2800 mA Output Current Setting Range with Constant Power EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) 450 mA 700 mA 1190 mA 1900 mA 700 mA 1050 mA 1750 mA 2800 mA Total Output Current Ripple (pk-avg) - 50%Iomax 100%Iomax 100% load. 20 MHz BW Startup Overshoot Current - - 10%Iomax 100% load No Load Output Voltage EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) 200 V 119 V 78 V 59 V Line Regulation - - ±5.0% 100% load Load Regulation - - ±5.0% Turn-on Delay Time - - 1.0 s Measured at 120Vac input, 75%-100% Load - - 0.5 s Measured at 220Vac input, 75%-100% Load Temperature Coefficient of Ioset - 0.06%/C - Case temperature = 0C ~Tc max Note: All specifications are typical at 25C unless otherwise stated.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com General Specifications Parameter Min. Typ. Max. Notes Efficiency at 120 Vac input: EUK-075S070DT(TT) Io= 450 mA Io= 700 mA EUK-075S105DT(TT) Io= 700 mA Io=1050 mA EUK-075S175DT(TT) Io=1190 mA Io=1750 mA EUK-075S280DT(TT) Io=1900 mA Io=2800 mA 85.5% 85.5% 85.5% 84.5% 85.0% 84.5% 83.5% 82.0% 87.5% 87.5% 87.5% 86.5% 87.0% 86.5% 85.5% 84.0% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Efficiency at 220 Vac input: EUK-075S070DT(TT) Io= 450 mA Io= 700 mA EUK-075S105DT(TT) Io= 700 mA Io=1050 mA EUK-075S175DT(TT) Io=1190 mA Io=1750 mA EUK-075S280DT(TT) Io=1900 mA Io=2800 mA 88.5% 88.0% 88.0% 87.0% 88.0% 87.0% 86.5% 85.0% 90.5% 90.0% 90.0% 89.0% 90.0% 89.0% 88.5% 87.0% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Efficiency at 277 Vac input: EUK-075S070DT(TT) Io= 450 mA Io= 700 mA EUK-075S105DT(TT) Io= 700 mA Io=1050 mA EUK-075S175DT(TT) Io=1190 mA Io=1750 mA EUK-075S280DT(TT) Io=1900 mA Io=2800 mA 88.5% 88.5% 88.5% 88.0% 88.0% 87.5% 86.5% 85.5% 90.5% 90.5% 90.5% 90.0% 90.0% 89.5% 89.0% 87.5% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) MTBF - 556,000 Hours - Measured at 220Vac input, 80%Load and 25C ambient temperature (MIL-HDBK- 217F) Lifetime - 84,000 Hours - Measured at 220Vac input, 80%Load and 70C case temperature; See lifetime vs. Tc curve for the details Operating Case Temperature for Safety Tc_s -40°C - +88°C Operating Case Temperature for Warranty Tc_w -40°C - +75C Case temperature for 5 years warranty Storage Temperature -40°C - +85°C Humidity: 5%RH to100%RH Dimensions Inches (L × W × H) Millimeters (L × W × H) 5.71 × 2.66 × 1.44 145 × 67.5 × 36.5 With mounting ear 6.54 × 2.66 × 1.44 166 × 67.5 × 36.5 Net Weight - 770 g - Note: All specifications are typical at 25C unless otherwise stated.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Dimming Specifications Safety &EMC Compliance Safety Category Standard CE EN 61347-1, EN61347-2-13 KS KS C 7655 EMI Standards Notes EN 55015(1) Conducted emission Test &Radiated emission Test EN 61000-3-2 Harmonic current emissions EN 61000-3-3 Voltage fluctuations & flicker FCC Part 15(1) ANSI C63.4 Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired Operation. Parameter Min. Typ. Max. Notes DT Models Absolute Maximum Voltage on the Vdim (+) Pin -20 V - 20 V Source Current on Vdim (+)Pin 200 uA 300 uA 450 uA Vdim(+) = 0 V Recommended Dimming Range for 0-10V 0 V - 10 V PWM_in High Level - 10V - PWM_in Low Level - 0V - PWM_in Frequency Range 200 Hz - 2 KHz PWM_in Duty Cycle 0% - 100% TT Models Dimming Level 10% - 100% Default is Traditional Timer. Dimming mode set to Self Adapting- Midnight or Self Adapting-Percentage in PC interface. Hold Time 0 Hours - 18 Hours Fade Time 0 Minutes - 60 Minutes Dimming Step 1 - 6 Dimming Output Range EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) 10%Ioset - Ioset 450 mA ≤ Ioset ≤ 700 mA 700 mA ≤ Ioset ≤ 1050 mA 1190 mA ≤ Ioset ≤ 1750 mA 1900 mA ≤ Ioset ≤ 2800 mA EUK-075S070DT(TT) EUK-075S105DT(TT) EUK-075S175DT(TT) EUK-075S280DT(TT) 45 mA 70 mA 119 mA 190 mA - Ioset 45 mA ≤ Ioset ＜ 450 mA 70 mA ≤ Ioset ＜ 700 mA 119 mA ≤ Ioset ＜ 1190 mA 190 mA ≤ Ioset ＜ 1900 mA
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Safety &EMC Compliance (Continued) EMS Standards Notes EN 61000-4-2 Electrostatic Disch arge (ESD): 8 kV air discharge, 4 kV contact discharge EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS EN 61000-4-5 Surge Immunity Test: AC Power Line: line to line 6 kV, line to earth 10 kV(2) EN 61000-4-6 Conducted Radio Fr equency Disturbances Test-CS EN 61000-4-8 Power Frequency Magnetic Field Test EN 61000-4-11 Voltage Dips EN 61547 Electromagnetic Immunity Require ments Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hi-pot) testing, the “GDT ground disconnect” (nut and metal lock sheet) on the driver end-cap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC 60598-1 Clause 10.2). After testing is completed, these items must be reinstalled to restore line-to-earth surge protection and secure the end cap. Derating
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Lifetime vs. Case Temperature Inrush Current Waveform Efficiency vs. Load EUK-075S070DT(TT)(Io=450mA) EUK-075S070DT(TT)(Io=700mA)
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com EUK-075S105DT(TT)(Io=700mA) EUK-075S105DT(TT)(Io=1050mA) EUK-075S175DT(TT)(Io=1190mA) EUK-075S175DT(TT)(Io=1750mA) EUK-075S280DT(TT)(Io=1900mA) EUK-075S280DT(TT)(Io=2800mA)
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Power Factor Total Harmonic Distortion Protection Functions Parameter Notes Over Temperature Protection Decreases output current, retu rning to normal after over temperature is removed. Short Circuit Protection Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Over Voltage Protection Limits output voltage at no load and in case the normal voltage limit fails.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Dimming 0-10V Dimming (Only DT models) The recommended implementation of the dimming control is provided below. Implementation 1 Notes: 1. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like resistors and zener. 2. If 0-10V dimming is not used, Dim + should be open. 10V PWM Dimming (Only DT models) Implementation 2 Notes: If PWM dimming is not used, Dim + should be open. Time Dimming (Only TT models) Time dimming control includes 3 kinds of modes, they are Self Adapting-Midnight, Self Adapting- Percentage and Traditional Timer. Self Adapting-Midnight : Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Output Lumen Compensation (Only TT models) Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRG-MUL2 Multi-Programmer datasheet for details. Mechanical Outline PROJ: Unspecified tolerance:±1 INPUT (UL SJTW 3*18AWG 7.8) AC/L (BLACK) AC/N (WHITE) GND (GREEN) V+ (RED) V- (BLUE) OUTPUT (UL SJTW 2*18AWG 7.3) Dimming Wire(UL21996 3*22AWG 5.0) BLACK/WHITE PURPLE GRAY Tc
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products.
Specifications are subject to changes without notice. EUK-075SxxxDT(TT) Rev. C 75W Programmable IP67 Driver www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com
Revision History
Date Rev. Description of Change Item From To 2017-09-25 A Datasheets Release / / 2017-11-10 B Operating Case Temperature for Safety Tc_s +90°C +88°C 2018-05-30 C Description / Updated Mechanical Outline / Updated