DS-ESD-150SXXXDT INVENTRONICS
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 14
Technical content
Features
Description
The ESD-150SxxxDT series is a 150W, constant-current, programmable LED driver th at operates from 249-528 Vac input with excellent power factor. Created for many lightin g applications including high bay, tunnel and roadway, it provides a dim-off mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input su rge, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range Full-Power Current Range (1) Default Output Current Input Voltage Range (2) Output Voltage Range Max. Output Power Typical Efficiency (3) Typical Power Factor Model Number 277Vac 480Vac 70-1050mA 700-1050mA 700 mA 249~528 Vac 352~500 Vdc 75~214Vdc 150 W 94.5% 0.96 0.95 ESD-150S105DT 140-2100mA 1400-2100m A 1400 mA 249~528 Vac 352~500 Vdc 38~107Vdc 150 W 94.0% 0.96 0.95 ESD-150S210DT 245-3500mA 2450-3500m A 2800 mA 249~528 Vac 352~500 Vdc 22 ~ 61Vdc 150 W 93.0% 0.96 0.95 ESD-150S350DT (4) 385-5600mA 3850-5600m A 4200 mA 249~528 Vac 352~500 Vdc 14 ~ 39Vdc 150 W 93.0% 0.96 0.95 ESD-150S560DT (4) Notes: (1) Output current range with constant power at 150W (2) Certified input voltage range: 277-480Vac or 352-500Vdc (3) Measured at 100% load and 480Vac input (see below “General Specifications” for details). (4) SELV Output Ultra High Efficiency (Up to 94.5%) Full Power at Wide Output Cur rent Range (Constant Power) Thermal Sensing and Protection for LED Module 0-10V/PWM/3-Timer-Modes Dimmable Dim-to-Off with Standby Power ≤ 1.5 W Output Lumen Compensation Input Surge Protection: DM 6kV, CM 10kV All-Around Protection: OVP, SCP, OTP IP67 and UL Dry / Damp / Wet Location SELV Output TYPE HL, for use in a Class I, Division 2 hazardous (Classified) location 5 Years Warranty
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com I-V Operating Area ESD-150S105DT ESD-150S210DT Output Voltage (V) Output Current (mA) Good Performance Area Allowed Operating Area Programmed Operating Area Note: 700mA≤Ioset≤1050mA (420,214)(70,214) 120 160 200 240 0 200 400 600 800 1000 1200 (700,214) (1050,143) 100%Load60%Load (1050,75) (Ioset,150/Ioset)(10%Ioset,150/Ioset) (105,75) (Ioset,75) (1050,86) (840,107)(140,107) (2100,43) 100 120 0 400 800 1200 1600 2000 2400 Output Voltage(V) (1400,107) (2100,71) (10%Ioset,150/Ioset) (Ioset,150/Ioset) 100%Load 60%Load Good Performance Area Allowed Operating Area (2100,38) Programmed Operating Area (210,38) (Ioset,38) Output Current (mA) Note: 1400mA≤Ioset≤2100mA ESD-150S350DT ESD-150S560DT (1470,61)(245,61) (3500,26) 0 700 1400 2100 2800 3500 4200 Output Voltage(V) (2450,61) (3500,43) (10%Ioset,150/Ioset) (Ioset,150/Ioset) 100%Load 60%Load Good Performance Area Allowed Operating Area (3500,22) Programmed Operating Area (350,22) (Ioset,22) Output Current (mA) Note: 2450mA≤Ioset≤3500mA (2310,39)(385,39) (5600,16) 0 1000 2000 3000 4000 5000 6000 Output Voltage(V) (3850,39) (5600,26.8) (10%Ioset,150 /Ioset) (Ioset,150/Ioset) 100%Load60%Load Good Performance Area Allowed Operating Area (5600,14) Programmed Operating Area (560,14) (Ioset,14) Output Current (mA) Note: 3850mA≤Ioset≤5600mA Input Specifications Parameter Min. Typ. Max. Notes Input AC Voltage 249 Vac - 528 Vac Input DC Voltage 352 Vdc - 500 Vdc Input Frequency 47 Hz - 63 Hz Leakage Current - - 0.75 MIU UL8750; 480Vac/ 60Hz, grounding effectively - - 0.70 mA IEC60598-1; 480Vac/ 60Hz, grounding effectively Input AC Current - - 0.70 A Measured at 100% load and 277 Vac input. - - 0.40 A Measured at 100% load and 480 Vac input. Inrush Current(I2t) - - 7.6 A 2s At 480Vac input, 25C Cold Start, Duration=680 μs, 10%Ipk-10%Ipk. See Inrush Current Waveform for the details.
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Input Specifications (Continued) Parameter Min. Typ. Max. Notes PF 0.90 - - At 277-480Vac, 50-60Hz,60%-100%Load Output Specifications Parameter Min. Typ. Max. Notes Output Current Tolerance -5%Ioset - 5%Ioset At 100% load condition Output Current Setting(Ioset) Range ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT 70 mA 140 mA 245 mA 385 mA 1050 mA 2100 mA 3500 mA 5600 mA Output Current Setting Range with Constant Power ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT 700 mA 1400 mA 2450 mA 3850 mA 1050 mA 2100 mA 3500 mA 5600 mA Total Output Current Ripple (pk-pk) - 5%Iomax 10%Iomax At 100% load condition, 20 MHz BW Output Current Ripple at < 200 Hz (pk-pk) - 2%Iomax - At 100% load condition. Only this component of ripple is associated with visible flicker. Startup Overshoot Current - - 10%Iomax At 100% load condition No Load Output Voltage ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT 223 V 116 V 64 V 43 V Line Regulation - - ±0.5% Measured at 100% load Load Regulation - - ±1.5% Turn-on Delay Time - 0.5 s 0.75 s Measured at 277Vac and 480Vac input, 60%-100% Load Temperature Coefficient of Ioset - 0.03%/C - Case temperature = 0C ~Tc max 12V Auxiliary Output Voltage (Vaux) 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current (Iaux) 0 mA - 200 mA Return terminal is “Dim−“
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com General Specifications Parameter Min. Typ. Max. Notes Efficiency at 277 Vac input: ESD-150S105DT Io= 700mA Io=1050mA ESD-150S210DT Io=1400mA Io=2100mA ESD-150S350DT Io=2450mA Io=3500mA ESD-150S560DT Io=3850mA Io=5600mA 91.5% 89.5% 91.0% 90.0% 91.0% 89.0% 90.5% 88.0% 93.5% 91.5% 93.0% 92.0% 93.0% 91.0% 92.5% 90.0% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Efficiency at 347 Vac input: ESD-150S105DT Io= 700mA Io=1050mA ESD-150S210DT Io=1400mA Io=2100mA ESD-150S350DT Io=2450mA Io=3500mA ESD-150S560DT Io=3850mA Io=5600mA 92.0% 90.5% 91.5% 90.5% 91.5% 89.5% 90.5% 88.5% 94.0% 92.5% 93.5% 92.5% 93.5% 91.5% 92.5% 90.5% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Efficiency at 480 Vac input: ESD-150S105DT Io= 700mA Io=1050mA ESD-150S210DT Io=1400mA Io=2100mA ESD-150S350DT Io=2450mA Io=3500mA ESD-150S560DT Io=3850mA Io=5600mA 92.5% 91.0% 92.0% 91.0% 91.0% 90.0% 91.0% 89.0% 94.5% 93.0% 94.0% 93.0% 93.0% 92.0% 93.0% 91.0% Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby power - - 1.5 W Measured at 480Vac/50Hz; Dimming off MTBF - 203,000 Hours - Measured at 480Vac input, 80%Load and 25C ambient temperature (MIL-HDBK- 217F) Lifetime - 99,000 Hours - Measured at 480Vac input, 80%Load and 70C case temperature with Iaux=100mA; See lifetime vs. Tc curve for the details Operating Case Temperature for Safety Tc_s -40°C - +88°C Operating Case Temperature for Warranty Tc_w -40°C - +75°C Humidity: 10%RH to 95%RH Storage Temperature -40°C - +85°C Humidity: 5%RH to 95%RH Dimensions Inches (L × W × H) Millimeters (L × W × H) 8.70 × 2.66 × 1.56 221 × 67.5 × 39.7 With mounting ear 9.53 × 2.66 × 1.56 242 × 67.5 × 39.7 Net Weight - 1300 g -
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Dimming Specifications Safety & EMC Compliance Safety Category Standard UL/CUL UL 8750,CAN/CSA-C22.2 No. 250.13 CE EN 61347-1, EN 61347-2-13 EMI Standards Notes EN 55015(1) Conducted emission Test & Radiated emission Test EN 61000-3-2 Harmonic current emissions EN 61000-3-3 Voltage fluctuations & flicker Parameter Min. Typ. Max. Notes Absolute Maximum Voltage on the Vdim (+) Pin -20 V - 20 V Source Current on Vdim (+)Pin 200 uA 300 uA 450 uA Vdim(+) = 0 V Dimming Output Range ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT 10%Ioset - Ioset 700mA ≤ Ioset ≤ 1050mA 1400mA ≤ Ioset ≤ 2100mA 2450mA ≤ Ioset ≤ 3500mA 3850mA ≤ Ioset ≤ 5600mA ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT 70 mA 140 mA 245 mA 385 mA - Ioset 70mA ≤ Ioset ＜ 700mA 140mA ≤ Ioset ＜ 1400mA 245mA ≤ Ioset ＜ 2450mA 385mA ≤ Ioset ＜ 3850mA Recommended Dimming Input Range 0 V - 10 V Default 0-10V dimming mode. Dim off Voltage 0.35 V 0.5 V 0.65 V Dim on Voltage 0.55 V 0.7 V 0.85 V Hysteresis - 0.2 V - PWM_in High Level 3 V - 10 V Dimming mode set to PWM in PC interface. PWM_in Low Level -0.3 V - 0.6 V PWM_in Frequency Range 200 Hz - 3 KHz PWM_in Duty Cycle 1% - 99% PWM Dimming off (Positive Logic) 2% 5% 8% PWM Dimming on (Positive Logic) 4% 7% 10% PWM Dimming off ( Negative Logic) 92% 95% 98% PWM Dimming on ( Negative Logic) 90% 93% 96% Hysteresis - 2% -
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Safety & EMC Compliance (Continued) EMI Standards Notes FCC Part15(1) ANSI C63.4 Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interfere nce, and [2] this device must accept any interference received, including interference that may cause undesired operation. EMS Standards Notes EN 61000-4-2 Electrostatic Disch arge (ESD): 8kV air discharge, 4kV contact discharge EN 61000-4-3 Radio-Frequency Elec tromagnetic Field Susceptibility Test-RS EN 61000-4-5 Surge Immunity Test: AC Power Line: Differential M ode 6kV, Common Mode 10kV(2) EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS EN 61000-4-8 Power Frequency Magnetic Field Test EN 61000-4-11 Voltage Dips EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hi-pot) testing, the “GDT gro und disconnect” (nut and metal lock sheet) on the driver end-cap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC 60598-1 Clause 10.2). After testing is completed , these items must be reinstalled to restore line-to-earth surge protection and secure the end cap. Lifetime vs. Case Temperature
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Inrush Current Waveform Efficiency vs. Load ESD-150S105DT(Io=700mA) ESD-150S105DT(Io=1050mA) ESD-150S210DT(Io=1400mA) ESD-150S210DT(Io=2100mA)
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com ESD-150S350DT(Io=2450mA) ESD-150S350DT(Io=3500mA) ESD-150S560DT(Io=3850mA) ESD-150S560DT(Io=5600mA) Power Factor
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Total Harmonic Distortion Protection Functions Parameter Notes Over Temperature Protection Decreases output current, returning to normal after over temperature is removed. Short Circuit Protection Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Over Voltage Protection Limits output voltage at no load and in case the normal voltage limit fails. External Thermal Protection NTC R1 - 7.81 kOhm - When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. R2 - 4.16 kOhm - When R_NTC is less than R2, output current is reduced to the programmed “Protection Current Floor.” Protection Current Setting Range 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset≤Iomin (default setting is 60% ) Dimming 0-10V Dimming The recommended implementation of the dimming control is provided below. Dim+ Dim- Dimmer Inventronics LED Driver V-L OTP- N G Vac Vaux OTP+ Implementation 1: DC Input
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Notes: 1. Do NOT connect Dim− to the output V− or V+, otherwise the dr iver will not work properly. 2. The dimmer can also be replaced by an active 0-10V voltage s ource signal or passive components like zener. PWM Dimming The recommended implementation of the dimming control is provided below. Dim+ Dim- Inventronics LED Driver V-L OTP- N G Vac Vaux OTP+ PWM Signal Implementation 2: Positive logic Dim+ Dim- Inventronics LED Driver V-L OTP- N G Vac Vaux OTP+ PWM Signal Implementation 3: Negative logic Notes: 1. Do NOT connect Dim− to the output V− or V+, otherwise the dr iver will not work properly. 2. When PWM negative logic dimming mode and Dim+ is open, the d river will dim to off and be standby. Time Dimming Time dimming control includes 3 kinds of modes, they are Self Adapting-Midnight, Self Adapting- Percentage and Traditional Timer. Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes.
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRG-MUL2 Multi-Programmer datasheet for details. Mechanical Outline PROJ: Unspecified tolerance:±1 INPUT(UL STW 3*18AWG 9.5) AC/L(BLACK) AC/N (WHITE) GND (GREEN) DIMMING WIRE (UL21996 5*22AWG 5.8) PINK BLACK/WHITE PURPLE BLUE/WHITE WHITE/PURPLE OUTPUT(UL SJTW 2*18AWG 7.3) V+ (RED) V- (BLUE) Tc
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com RoHS Compliance Our products comply with reference to RoHS Directive (EU) 2015/ 863 amending 2011/65/EU, calling for the elimination of lead and other hazardous substances from electronic products.
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com
Revision History
Date Rev. Description of Change Item From To 2015-09-23 A Datasheets Release / / 2016-06-02 B Input AC Current / Updated General Specifications With mounting ear Added General Specifications Net Weight Added Safety &EMC Compliance Notes Added Programming Connection Diagram / Updated Mechanical Outline / Updated 2017-08-03 C Features / Updated Input Specifications PF/THD Updated Output Specifications Turn-on Delay Time Updated Output Specifications Temperature Coefficient of Ioset Updated Safety & EMC Compliance / Updated Mechanical Outline / Updated 2019-06-26 D CE / Updated Features / Updated Description / Updated Models / Updated Input Specifications Input Voltage Updated Input Specifications Leakage Current Updated Output Specifications Turn-on Delay Time Updated General Specifications Lifetime Updated Safety & EMC Compliance / Updated Lifetime vs. Case Temperature / Updated Mechanical Outline / Updated
Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. 150W Programmable IP67 Driver ESD-150SxxxDT Rev. E www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com Revision History (Continued) Change Date Rev. Description of Change Item From To 2022-03-10 E Product Photograph / Updated Features / Updated General Specifications Humidity Updated Dimming / Updated Programming Connection Diagram / Updated Mechanical Outline / Updated RoHS Compliance / Updated