UPG2157T5F-E2

UPG2157T5F CEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

DESCRIPTION

The +PG2157T5F is a GaAs MMIC 50 1 termination type high power SPDT (S ingle Pole Double Throw) switch which was developed for WiMAX. This device can operate from frequency 2.3 to 5.85 GHz, with low insertion loss and high isolation. This device is housed in a 12-pin plastic QFN (Q uad Flat Non-leaded) package. This package is suitable for high- density surface mounting.

FEATURES

• Control voltage : V cont (H) = 2.5 to 3.3 V (3.0 V TYP.) V: cont (L) = 0 to 0.4 V (0 V TYP.)
• High isolation : ISL1 = 28 dB TYP. @ f = 2.3 to 2.7 GHz, V cont (H) = 3.0 V, Vcont (L) =0V V,zHG8.3ot3.3=f@.PYTBd52=2LSI: cont (H) = 3.0 V, Vcont (L) =0V V,zHG58.5ot51.5=f@.PYTBd22=3LSI: cont (H) = 3.0 V, Vcont (L) = 0 V
• Handling power : P in (1 dB) * +37.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V P: in (1 dB) * +37.0 dBm TYP. @ f = 5.85 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V
• High-density surface mounting : 12-pin plastic QFN package (3.0 = 3.0 = 0.75 mm)

APPLICATIONS

• Antenna switch for WiMAX, 802.11a/b/g access point

ORDERING INFORMATION

Part Number Order Number Package Marking Supplying Form +PG2157T5F-E2 +PG2157T5F-E2-A 12-pin plastic QFN (Pb-Free) 2157 % Embossed tape 8 mm wide % Pin 1 indicates roll-in direction of tape % Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: +PG2157T5F-A DATA SHEET Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. 50 1 TERMINATION TYPE HIGH POWER SPDT SWITCH FOR WiMAX GaAs INTEGRATED CIRCUIT +PG2157T5F Document No. PG10641EJ01V0DS (1st edition) Date Published October 2006 NS CP(K) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.

PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM Pin No. Pin Name

1 GND

2 INPUT

3 GND

4 GND

6 GND

7 OUTPUT2

8 GND

9 OUTPUT1

10 GND

11 V cont1

(Top View) 2157 1112 10 546 (Bottom View) 1110 12 564 (Top View) 1112 10 546 50 1 50 1

12 GND

Remark Exposed pad : GND TRUTH TABLE Vcont1V cont2 INPUT<OUTPUT1 INPUT <OUTPUT2 High Low ON OFF Low High OFF ON ABSOLUTE MAXIMUM RATINGS (TA =+ 2 5$C, unless otherwise specified) Parameter Symbol Ratings Unit Switch Control Voltage V cont +6.0 V PrewoPtupnI in +38 dBm Operating Ambient Temperature T A <45 to +85 $C Storage Temperature T stg <55 to +150 $C RECOMMENDED OPERATING RANGE (TA =+ 2 5$C, unless otherwise specified) Parameter Symbol MIN. TYP. MAX. Unit Operating Frequency f opt1 2.3 < 2.7 GHz fopt2 3.3 < 3.8 GHz fopt3 5.15 < 5.85 GHz Switch Control Voltage (H) V cont (H) 2.5 3.0 3.3 V Switch Control Voltage (L) V cont (L) 0 0 0.4 V Data Sheet PG10641EJ01V0DS2 +PG2157T5F

ELECTRICAL CHARACTERISTICS

(TA =+ 2 5$C, V cont (H) = 3.0 V, V cont (L) = 0 V, DC blocking capacitors = 8 pF, unless otherwise specified) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit L1ssoLnoitresnI ins1 f = 2.3 to 2.7 GHz < 0.60 0.85 dB L2ssoLnoitresnI ins2 f = 3.3 to 3.8 GHz < 0.60 0.85 dB L3ssoLnoitresnI ins3 f = 5.15 to 5.85 GHz < 0.80 1.05 dB Isolation 1 (INPUT<OFF Port) 8252zHG7.2ot3.2=f1LSI < dB Isolation 2 (INPUT<OFF Port) 5222zHG8.3ot3.3=f2LSI < dB Isolation 3 (INPUT<OFF Port) 2291zHG58.5ot51.5=f3LSI < dB Isolation 4 (OUTPUT1<OUTPUT2) 6232zHG7.2ot3.2=f4LSI < dB Isolation 5 (OUTPUT1<OUTPUT2) 3202zHG8.3ot3.3=f5LSI < dB Isolation 6 (OUTPUT1<OUTPUT2) 1281zHG58.5ot51.5=f6LSI < dB Input Return Loss 1 RL in1 f = 2.3 to 2.7 GHz < 20 < dB Input Return Loss 2 RL in2 f = 3.3 to 3.8 GHz < 20 < dB Input Return Loss 3 RL in3 f = 5.15 to 5.85 GHz < 20 < dB Output Return Loss 1 RL out1 f = 2.3 to 2.7 GHz < 20 < dB Output Return Loss 2 RL out2 f = 3.3 to 3.8 GHz < 20 < dB Output Return Loss 3 RL out3 f = 5.15 to 5.85 GHz < 20 < dB Return Loss (OFF Port) RL f = 2.3 to 2.7 GHz < 15 < dB zHG8.3ot3.3=f < 15 < dB zHG58.5ot51.5=f < 15 < dB 1 dB Loss Compression P in (1 dB) f = 2.5 GHz <* +37.0 < dBm Input Power Note f = 5.85 GHz <* +37.0 < dBm Switch Control Current I cont < 20 30 +A Switch Control Speed t SW 50% CTL to 90/10% RF < 100 < ns Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Data Sheet PG10641EJ01V0DS 3 +PG2157T5F

The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. Data Sheet PG10641EJ01V0DS4 +PG2157T5F

MOUNTING PAD LAYOUT DIMENSIONS 12-PIN PLASTIC QFN (UNIT: mm) 1.55 0.5 1.0 12–0.3 0.5 1.0 0.650.65 0.5 1.0 0.5 1.0 0.650.65 1.55 Remark The mounting pad layouts in this document are for reference only. Data Sheet PG10641EJ01V0DS 5 +PG2157T5F

12-PIN PLASTIC QFN (UNIT: mm) 3.0±0.1 3.0±0.1 0.75±0.1 (Bottom View) 0.5±0.06 1.0 0.9 0.4 Dimensions of pin No.1 indication 0.5±0.06 1.0 0.4±0.1 0.24+0.07 –0.05 1.55±0.1 0.4±0.1 0.4±0.1 Data Sheet PG10641EJ01V0DS6 +PG2157T5F

RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. gniredloSdohteMgniredloS lobmySnoitidnoCsnoitidnoC Infrared Reflow Peak temperature (package surface temperature) : 260 $C or below sselrosdnoces01:erutarepmetkaeptaemiT Time at temperature of 220$C or higher : 60 seconds or less Preheating time at 120 to 180$ 021:C (30 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below IR260 Wave Soldering Peak temperature (molten solder temperature) : 260 $C or below sselrosdnoces01:erutarepmetkaeptaemiT Preheating temperature (package surface temperature) : 120 $C or below Maximum number of flow processes : 1 time Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below WS260 Partial Heating Peak temperature (terminal temperature) : 350$C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10641EJ01V0DS 7 +PG2157T5F

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A -AZLead (Pb) < 1000 PPM Not Detected (*) Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sol d by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.