UPG168TB CEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

UPG168TBNEC's L, S-BAND SPDT SWITCH California Eastern Laboratories

  • SWITCH CONTROL VOLTAGE: Vcont (H) = 2.5 to 5.3 V (3.0 V TYP.) Vcont (L) = −0.2 to +0.2 V (0 V TYP.)
  • LOW INSERTION LOSS: L INS2 = 0.40 dB TYP. @ f = 2.0 GHz, Vcont = 3.0 V/0V
  • HIGH ISOLATION: ISL1 = 27 dB TYP. @ f = 0.5 to 2.0 GHz, Vcont = 3.0 V/0 V ISL2 = 18 dB MIN. @ f = 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V
  • MIDDLE POWER: Pin (1 dB) = +26.5 dBm TYP . @ f = 1.0 GHz, Vcont = 3.0 V/0 V
  • HIGH-DENSITY SURFACE MOUNTING: 6-pin super minimold package (2.0 × 1.25 × 0.9 mm)

FEATURES

ORDERING INFORMATION

Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPG168TB NEC's UPG168TB is GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which were developed for mobile phone and another L, S-band application. This device can operate frequency from 0.5 to 2.5 GHz, having the low insertion loss and high isolation. This device is housed in a 6-pin super minimold pack- age. And this package is able to high-density surface mounting.

DESCRIPTION

  • L-band digital cellular or cordless telephone
  • PCS, W-LAN, WLL and BluetoothTM etc. APPLICATION PART NUMBER PACKAGE MARKING SUPPLYING FORM UPG168TB-E4 6-pin super minimold G2T • Embossed tape 8 mm wide
  • Pin 4, 5, 6 face the perforation side of the tape
  • Qty 3 kpcs/reel Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.

PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM TRUTH TABLE Vcont1 Vcont2 INPUT-OUTPUT1 INPUT-OUTPUT2 Low High ON OFF High Low OFF ON ABSOLUTE MAXIMUM RATINGS (TA =+25ºC, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Switch Control Voltage Vcont −6.0 to +6.0 Note 1 V Input Power Pin +28 dBm Power Dissipation PD 150 Note 2 mW Operating Ambient Temperature TA −45 to +85 °C Storage Temperature Tstg −55 to +150 °C Notes 1. Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB, TA = +85°C 2. | Vcont1 − Vcont2 | ≤ 6.0 V PIN NO. PIN NAME

1 OUTPUT2

2 GND

3 OUTPUT1

4 Vcont1

5 INPUT

6 V cont2

(Top View) G2T (Top View) (Bottom View) PARAMETER SYMBOL MIN. TYP. MAX. UNIT Switch Control Voltage (H) Vcont (H) 2.5 3.0 5.3 V Switch Control Voltage (L) Vcont (L) −0.2 0 0.2 V RECOMMENDED OPERATING RANGE (TA =+25ºC, unless otherwise specified)

ELECTRICAL CHARACTERISTICS (TA = +25°C, Vcont = 3.0 V/0 V, DC blocking capacitors = 51 pF, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Insertion Loss 1 LINS1 f = 0.5 to 1.0 GHz − 0.30 0.55 dB Insertion Loss 2 LINS2 f = 2.0 GHz − 0.40 0.65 dB Insertion Loss 3 LINS3 f = 2.0 to 2.5 GHz − − 0.90 dB Isolation 1 ISL1 f = 0.5 to 2.0 GHz 22 27 − dB Isolation 2 ISL2 f = 2.0 to 2.5 GHz 18 − − dB Input Return Loss 1 RLin1 f = 0.5 to 2.0 GHz 13 19 − dB Input Return Loss 2 RLin2 f = 2.0 to 2.5 GHz 11 − − dB Output Return Loss 1 RLout1 f = 0.5 to 2.0 GHz 13 19 − dB Output Return Loss 2 RLout2 f = 2.0 to 2.5 GHz 11 − − dB 1 dB Gain Compression Input Power Note Pin (1 dB) f = 1.0 GHz +22.0 +26.5 − dBm Switch Control Speed tSW − 50 200 ns Switch Control Current Icont − 0.5 10 μA Note P in (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25°C, Vcont = 3.0 V/0 V, DC cut capacitors = 51 pF, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT 0.1 dB Gain Compression Input Power Note Pin (0.1 dB) f = 1.0 GHz − +23.0 − dBm Note P in (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of recommended DC cut capacitor value is less than 100 pF.

EVALUATION CIRCUIT (Vcont = 3.0 V/0 V, DC blocking capacitors = 51 pF) This application circuit and its parameters are for reference only. OUTPUT2 OUTPUT1 Vcont2 INPUT Vcont1 51 pF 51 pF 1000 pF 1000 pF51 pF 6 5 4 1 2 3

ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD VC 2 VC 1 IN OUT 1 OUT 2 6Pin SMM SPDT SW C1C5 C1C1 G2T VDD Vcont INPUT OUTPUT1 OUTPUT2 USING THE NEC EVALUATION BOARD SYMBOL VALUES C1, C2, C3 51 pF C4, C5 1000 pF

6-PIN SUPER MINIMOLD (UNIT:mm) 0.9±0.1 0.7 0 to 0.1 0.15+0.1 -0.05 0.2+0.1 -0.05 2.0±0.2 1.3 0.650.65 1.25±0.1 2.1±0.1 0.1 MIN.

RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Soldering Conditions Condition Symbol Infrared Reflow Peak temperature (package surface temperature) : 260 °C or below Time at peak temperature : 10 seconds or less Time at temperature of 220°C or higher : 60 seconds or less Preheating time at 120 to 180°C : 120±30 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below IR260 VPS Peak temperature (package surface temperature) : 215 °C or below Time at temperature of 200°C or higher : 25 to 40 seconds Preheating time at 120 to 150°C : 30 to 60 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below VP215 Wave Soldering Peak temperature (molten solder temperature) : 260 °C or below Time at peak temperature : 10 seconds or less Preheating temperature (package surface temperature) : 120 °C or below Maximum number of flow processes : 1 time Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below WS260 Partial Heating Peak temperature (pin temperature) : 350°C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. A Business Partner of NEC Compound Semiconductor Devices, Ltd. 03/15/2005