UPB1510GV-E1-A

UPB1510GV CEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX ICC Circuit Current, No Input Signal mA 10.5 14 17 fIN (u)1 Upper Limit Operating Frequency 1, P IN = -10 to +6 dBm GHz 3.0 fIN (u)2 Upper Limit Operating Frequency 2, P IN = -15 to +6 dBm GHz 2.7 fIN (L) Lower Limit Operating Frequency, PIN = -15 to +6 dBm GHz 0.5 PIN1 Input Power 1, f IN = 2.7 to 3.0 GHz dBm -10 +6 PIN2 Input Power 2, f IN = 1.0 to 2.7 GHz dBm -15 +6 POUT Output Power, PIN = 0 dBm, fIN = 2.0 GHz dBm -12 -7

3.0 GHz DIVIDE BY 4 PRESCALER

FEATURES

• HIGH FREQUENCY OPERATION TO 3 GHz
• LOW CURRENT CONSUMPTION: 15 mA at 5 V
• SMALL PACKAGE: 8 PIN SSOP
• AVAILABLE IN TAPE AND REEL

DESCRIPTION

NEC's UPB1510GV is a Silicon RFIC digital prescaler manu- factured with the NESAT™ IV silicon bipolar process. It fea- tures frequency response to 3 GHz, a divide-by-four ratio, and operates on a 5 volt supply while drawing only 15 mA. The device is housed in a small 8 pin SSOP package that contrib- utes to system miniaturization. The low power consumption and wide frequency operation makes the device well suited for use in a PLL synthesizer for UHF/VHF TV and DBS tuner applications. UPB1510GV ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 4.5 to 5.5 V, ZS = ZL = 50 Ω) TEST CIRCUIT Power Supply 1000 pF OPEN OPEN 1000 pF C1 2200 pF 1000 pF 1000 pF 5 V ± 0.5 V RFIN OUT California Eastern Laboratories

Pin No. Symbol Applied Description Voltage 1000 pF). 2 IN – Signal input pin. This pin should be coupled to source with a capacitor (e.g. 1000 pF). 3 IN – Signal input bypass pin. This pin must be equipped with a bypass capacitor (e.g. 1000 pF) to ground. 4 GND 0 Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance.

5 GND 0

6 NC – No connection, this pin should be left open. 7 OUT – Divided frequency output pin. This pin is designed as an emitter follower output, and should be coupled to the load with a capacitor (e.g. 1000 pF). 8 NC – No connection, this pin should be left open. SYMBOLS PARAMETERS UNITS RATINGS VCC Supply Voltage V 6.0 VIN Input Voltage V 6.0 PD Total Power Dissipation2 mW 250 TA Operating Ambient Temp. °C -40 to +85 TSTG Storage Temperature °C -55 to +150 ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) UPB1510GV SYMBOL PARAMETER UNITS MIN TYP MAX VCC Supply Voltage V 4.5 5.0 5.5 TA Operating Ambient Temp. °C -40 +25 +85 RECOMMENDED OPERATING CONDITIONS Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy glass PWB (T A = +85˚C). PIN DESCRIPTIONS SYSTEM APPLICATION EXAMPLE BPF OSC MIX FM demo PLL synth. for VHF/UHF band AGC ampSAW LPF Prescaler 1st IF Input from DBS converter Baseband Output UPB1510GV RF UNIT BLOCK OF DBS TUNER INTERNAL BLOCK DIAGRAM IN IN CLK D CLK Q Q AMP OUT D CLK CLK Q Q

TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) Supply Voltage, VCC (V) Circuit Current, I CC (mA) CURRENT vs. VOLTAGE and TEMPERATURE 763210 No input signal TA = +85°C TA = -40°C TA = +25°C TA = +25°C VCC = 4.5 to 5.5 V Guaranteed operating range +20 +10 -10 -20 -30 -40 -50 1030.1 1 0.5 +20 +10 -10 -20 -30 -40 -50 1030.1 VCC = 5 V Guaranteed operating range TA = 25°C TA = 85°C TA = -40°C TA = 85°C TA = 25°C TA = -40°C 10.5 -10 -15 1030.1 1 0.5 TA = 85°C TA = 25°C TA = -40°C VCC = 5 V PIN = 0 dBm ZL = 50 W -10 -15 1030.1 1 0.5 VCC = 5.5 V VCC = 5 V VCC = 4.5 V TA = 25°C PIN = 0 dBm ZL = 50 Ω -10 -15 1030.1 1 0.5 VCC = 5.5 V VCC = 5 V VCC = 4.5 V TA = -40°C PIN = 0 dBm ZL = 50 Ω Input Frequency, fin (MHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (GHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (GHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (GHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (GHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and VOLTAGE UPB1510GV

TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) -10 -15 1030.1 1 0.5 VCC = 5.5 VVCC = 5 V VCC = 4.5 V TA = 85°C PIN = 0 dBm ZL = 50 Ω UPB1510GV S11 Z REF 1.0 Units 200.0 mUnits/ 27.159 Ω -27.582 Ω hp MARKER 4

3 GHz

S11 vs. INPUT FREQUENCY VCC = 5.0 V, TA = 25°C, ZO = 50 ΩΩΩΩΩ START 0.500000000 GHz STOP 3.000000000 GHz TYPICAL SCATTERING PARAMETERS (TA = 25°C) : 500 MHz : 1000 MHz : 2000 MHz : 3000 MHz FREQUENCY S 11 (Ω)(Ω)(Ω)(Ω)(Ω) MHz 500 37.1 - j207.8 1000 14.2 - j105.1 2000 7.9 - j35.8 3000 27.1 - j27.5 Input Frequency, fin (GHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE

TYPICAL SCATTERING PARAMETERS (TA = 25°C) S22 Z REF 1.0 Units 200.0 mUnits/ 60.925 Ω 104.77 Ω hp MARKER 4

750 MHz

S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 500 MHz, TA = 25°C, ZO = 50 ΩΩΩΩΩ START 0.125000000 GHz STOP 0.750000000 GHz S22 Z REF 1.0 Units 200.0 mUnits/ 15.613 Ω 98.168 Ω hp MARKER 4 S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 3 GHz, TA = 25°C, ZO = 50 ΩΩΩΩΩ START 0.125000000 GHz STOP 0.750000000 GHz : 125 MHz : 250 MHz : 500 MHz : 750 MHz : 125 MHz : 250 MHz : 500 MHz : 750 MHz FREQUENCY S 22 (Ω)(Ω)(Ω)(Ω)(Ω) MHz 125 55.5 + j6.7 250 53.7 + j30.4 500 55.0 + j60.3 750 60.9 + j104.8 FREQUENCY S 22 (Ω)(Ω)(Ω)(Ω)(Ω) MHz 125 28.5 + j11.5 250 27.6 + j23.6 500 20.5 + j50.7 750 15.6 + j98.2

ORDERING INFORMATION

OUTLINE DIMENSIONS (Units in mm) PIN CONNECTIONS 1. VCC 5. GND 2. IN 6. NC 3. IN 7. OUT 4. GND 8. NC Note: 1. Embossed tape 8 mm wide. Pin 1 is in the tape pull-out direction. 8 7 6

3.0 MAX

1.5±0.1

1.8 MAX

0.1 ± 0.1 0.3 +0.10 -0.05

0.575 MAX

0.15+0.10 -0.05 4.94 ± 0.2 3.2±0.1 0.87±0.2 0.5 ± 0.2 0.65 3 +7˚ -3˚ Detail of Lead End 0.15 1510 EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 09/13/2000DATA SUBJECT TO CHANGE WITHOUT NOTICE Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A -AZLead (Pb) < 1000 PPM Not Detected (*) Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substan ce content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway t o better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and ac curate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.