UPB1509GV CEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX ICC Supply Current, No Input Signal, Vcc = 3 V mA 3.5 5.0 5.9 fIN (u) Upper Limit Operating Frequency, PIN = -20 to 0 dBm MHz 500 PIN = -20 to -5 dBm at÷ 2 MHz 700 at ÷ 4 MHz 800 at ÷ 8 MHz 1000 fIN (L) Lower Limit Operating Frequency, PIN = -20 to 0 dBm MHz 50 PIN = -20 to -5 dBm MHz 500 PIN Input Power, fIN = 50 to 1000 MHz dBm -20 -5 fIN = 50 to 500 MHz dBm -20 0 VOUT Output Voltage, RL = 200 Ω VP-P 0.1 0.2 VIN(H) Division Ratio Control Voltage High V V CC VIN(L) Division Ratio Control Voltage Low V OPEN NEC's 1.0 GHz DIVIDE BY 2/4/8 PRESCALER

FEATURES

  • HIGH FREQUENCY OPERATION TO 1 GHz
  • SELECTABLE DIVIDE RATIO: ÷2, ÷4, ÷8
  • WIDE SUPPLY VOLTAGE RANGE: 2.2 TO 5 V
  • LOW SUPPLY CURRENT: 5.3 mA
  • SMALL PACKAGE: 8 pin SSOP
  • AVAILABLE IN TAPE AND REEL

DESCRIPTION

NEC's UPB1509GV is a Silicon RFIC digital prescaler manu- factured with the NESAT™ IV silicon bipolar process. It fea- tures frequency response to 1 GHz, selectable divide-by-two, four, or eight modes, and operates from a 3 to 5 volt supply while drawing only 5.3 milliamps. The device is housed in a small 8 pin SSOP package that contributes to system miniatur- ization. The low power consumption and wide supply range makes the device well suited for cellular and cordless tele- phones as well as DBS receiver applications. TEST CIRCUIT BIPOLAR DIGITAL INTEGRATED CIRCUIT UPB1509GV VCC C C C C C C C C = 1000 pF VOUT fIN VCC1 IN IN GND VCC2 OUT SW2 SW1 The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 2.2 to 5.5 V, unless otherwise noted) Date Published: June 28, 2005

Pin No. Symbol Applied Pin Description Voltage Voltage 1 VCC1 2.2 to 5.5 – Power supply pin of input amplifier and dividers. This pin must be equipped with bypass capacitor (eg 1000 pF) to ground. 2 I N – 1.7 to 4.95 Signal input pin. This pin should be coupled with a capacitor (eg 1000 pF). 3 I N – 1.7 to 4.95 Signal input bypass pin. This pin must be equipped with a bypass capacitor (eg 1000 pF) to ground. 4 GND 0 – Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. 5 SW1 H/L – Divided ratio control pin. Divide ratio can be controlled by the following (VCC /OPEN) input voltages to these pins.

6 SW2 H/L

(VCC /OPEN) These pins must each be equipped with a bypass capacitor to ground. 7 OUT – 1.0 to 4.7 Divided frequency output pin. This pin is designed as an emitter follower output. This pin can output 0.1 Vp-p min with a 200 Ω load. This pin should be coupled to load device with a capacitor (eg 1000 pF). 8V CC2 2.2 to 5.5 – Power supply pin of output buffer amplifier. This pin must be equipped with bypass capacitor (eg 1000 pF) to ground. SYMBOLS PARAMETERS UNITS RATINGS VCC1, VCC2 Supply Voltage V 6.0 VIN Input Voltage V 6.0 PD Power Dissipation2 mW 250 TOP Operating Temperature °C -45 to +85 TSTG Storage Temperature °C -55 to +150 ABSOLUTE MAXIMUM RATINGS 1 (TA = 25°C) RECOMMENDED OPERATING CONDITIONS Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy glass PWB (T A = +85˚C). INTERNAL BLOCK DIAGRAM SW2 H (VCC )L (OPEN) H (VCC ) 1/2 1/4 SW1 L (OPEN) 1/4 1/8 PIN DESCRIPTIONS IN SW1 SW2 OUT D CLK Q IN Q D CLK Q Q D CLK Q Q UPB1509GV SYMBOL PARAMETER UNITS MIN TYP MAX VCC1, VCC2 Supply Voltage V 2.2 3.0 5.5 TOP Operating Temperature °C -40 +25 +85

TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) Input Power, P IN (dBm) 0123 4 56 Recommended operating range TA = -40°C TA = +25°C TA = +85°C TA = +25¡C +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 VCC = 5.5 V VCC = 2.2 V VCC = 3.0 V VCC = 5.5 V VCC = 2.2 VVCC = 3.0 V Guaranteed Operating Window VCC = 3.0 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +25°C TA = +85°C TA = -40°C Guaranteed operating window TA = +25°C TA = +85°CTA = -40°C VCC = 2.2 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +25°C TA = +85°C TA = -40°C Guaranteed operating window TA = +25°C TA = +85°C TA = -40°C Supply Voltage, VCC (V) Circuit Current, I CC (mA) CIRCUIT CURRENT vs. SUPPLY VOLTAGE and TEMPERATURE Input Frequency, fin (MHz) OutputVoltage Swing, V P-P (V) OUTPUT VOLTAGE SWING vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and VOLTAGE VCC = 5.5 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +25°C TA = +85°C TA = -40°C Guaranteed operating window TA = +85°C TA = -40°C TA = +25°C TA = +85°C TA = -40°C TA = +85°C TA = -40°C TA = +25°C TA = +25°C VCC = 3.0 V PIN = 0 dBm 0.3 0.2 0.1 200010010 1000 Input Power, P IN (dBm) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE

TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) TA = +25°C PIN = 0 dBm 0.3 0.2 0.1 200010010 1000 VCC = 5.5 V VCC = 2.2 V VCC = 3.0 V TA = -40°C PIN = 0 dBm 0.3 0.2 0.1 200010010 1000 VCC = 5.5 V VCC = 2.2 V VCC = 3.0 V TA = +85°C PIN = 0 dBm 0.3 0.2 0.1 200010010 1000 VCC = 5.5 V VCC = 2.2 V VCC = 3.0 V TA = +25ºC +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 VCC = 5.5 V VCC = 5.5 V VCC = 2.2 V VCC = 3.0 V Guaranteed Operating Window VCC = 3.0 V VCC = 5.5 V VCC = 2.2 V Input Frequency, fin (MHz) Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) VCC = 3.0 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +25°C TA = +85°C TA = -40°C Guaranteed operating window TA = +85°C TA = -40°C TA = +25°C Input Power, P IN (dBm) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) OutputVoltage Swing, V P-P (V) OutputVoltage Swing, V P-P (V) OUTPUT VOLTAGE SWING vs. INPUT FREQUENCY and VOLTAGE OUTPUT VOLTAGE SWING vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) OutputVoltage Swing, V P-P (V) OUTPUT VOLTAGE SWING vs. INPUT FREQUENCY and VOLTAGE Divide by 4 mode (Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85°C)

VCC = 3.0 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +85°C TA = -40°C Guaranteed operating window TA = +85°C TA = +25°C TA = +25°C TA = -40°C TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) Input Power, P IN (dBm) VCC = 5.5 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +85°C TA = -40°C Guaranteed operating window TA = +85°C TA = +25°C TA = -40°C TA = -40°C TA = +25°C TA = +25°C +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 VCC = 2.2 V VCC = 3.0 V Guaranteed Operating Window VCC = 3.0 V VCC = 5.5 V VCC = 2.2 V VCC = 5.5 V VCC = 3.0 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +85°C TA = -40°C Guaranteed operating window TA = -40°C TA = +25°C TA = -40°C TA = +85°C TA = +25°C VCC = 2.2 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = -40°C Guaranteed operating window TA = +85°C TA = +25°C TA = +25°C TA = -40°C TA = +85°C TA = +25°C Input Frequency, fin (MHz) Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) VCC = 5.5 V +20 +10 -10 -20 -30 -40 -50 -60 200010010 1000 TA = +85°C TA = -40°C Guaranteed operating window TA = +85°C TA = +25°C TA = -40°C TA = +25°C Input Power, P IN (dBm) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Power, P IN (dBm) Divide by 8 mode (Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85 °C)

REF 1.0 Units/ 200.0 mUnits/ 55.375 Ω -142.79 Ω MARKER 2

700.0 MHZ

S11 vs. INPUT FREQUENCY START 0.050000000 GHz STOP 1.000000000 GHz TYPICAL SCATTERING PARAMETERS (TA = 25°C) S22 REF 1.0 Units 200.0 mUnits/ S22 vs. OUTPUT FREQUENCY START 0.050000000 GHz STOP 0.350000000 GHz Z

50 MHz

149.09 Ω + j 14.86 Ω

350 MHz

194.21 Ω – j 36.64 Ω FREQUENCY S 11 GHz MAG ANG 0.1 0.929 -6.7 0.2 0.898 -10.5 0.3 0.866 -13.6 0.4 0.840 -15.9 0.5 0.834 -19.1 0.6 0.819 -21.9 0.7 0.803 -24.7 0.8 0.792 -27.0 0.9 0.787 -30.0 1.0 0.771 -32.7 VCC1 = VCC2 = 3.0 V, SW1 = SW2 = 3.0 V

OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S08 PIN CONNECTIONS 1. VCC1 2. IN 3. IN 4. GND 5. SW1 6. SW2 7. OUT 8. V CC2 8 7 6

3.0 MAX

N 1509 1.5±0.1

1.8 MAX

0.1 ± 0.1 0.3+0.10 -0.05

0.575 MAX

0.15+0.10 -0.05 4.94 ± 0.2 3.2±0.1 0.87±0.2 0.5 ± 0.2 0.150.65 3 +7˚ -3˚ Detail of Lead End SYSTEM APPLICATION EXAMPLE RX TX SW PA VCO DEMO N N PLL PLL 90¡ µPB1509GV I Q I Q Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. ORDERING INFORMATION (Solder Contains Lead) PART NUMBER QUANTITY UPB1509GV-E1 1000/Reel ORDERING INFORMATION (Pb-Free) PART NUMBER QUANTITY UPB1509GV-E1-A 1000/Reel A Business Partner of NEC Compound Semiconductor Devices, Ltd.

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A -AZLead (Pb) < 1000 PPM Not Detected (*) Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.