UPB1508GV

UPB1508GV CEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX ICC Supply Current mA 7.6 12 14.5 fIN (U) Upper Limit Operating Frequency, PIN = -10 to +6 dBm GHz 3.0 PIN = -15 to +6 dBm GHz 2.7 fIN (L) Lower Limit Operating Frequency, PIN = -15 to +6 dBm GHz 0.5 PIN Input Power, fIN = 2.7 to 3.0 GHz dBm -10 +6 fIN = 0.5 to 2.7 GHz dBm -15 +6 POUT Output Power, PIN =0 dBm, fIN = 2 GHz dBm -12 -7

3.0 GHz

FEATURES

• HIGH FREQUENCY OPERATION TO 3 GHz
• FIXED DIVIDE RATIO: ÷2
• LOW CURRENT CONSUMPTION: 12 mA at 5 V
• SMALL PACKAGE: 8 pin SSOP
• AVAILABLE IN TAPE AND REEL

DESCRIPTION

NEC's UPB1508GV is a Silicon RFIC digital prescaler manu- factured with the NESAT™ IV silicon bipolar process. It fea- tures frequency response to 3 GHz, a divide-by-two ratio, and operates on a 5 volt supply while drawing only 12 mA. The device is housed in a small 8 pin SSOP package that contrib- utes to system miniaturization. The low power consumption and wide frequency operation makes the device well suited for use in a PLL synthesizer for UHF/VHF TV and DBS tuner applications. INTERNAL BLOCK DIAGRAM UPB1508GV ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 4.5 to 5.5 V, ZS = ZL = 50 Ω) California Eastern Laboratories IN AMP OUTIN D CLK CLK Q Q

Pin no. Symbol Applied Pin Description Voltage Voltage 1V CC 4.5 to 5.5 Power supply pin. This pin must be equipped with bypass capacitor (eg 1000 pF) to ground. 2 IN 1.7 to 4.95 Signal input pin. This pin should be coupled with a capacitor (eg 1000 pF). 3 IN 1.7 to 4.95 Signal input bypass pin. This pin must be equipped with a bypass capacitor (eg 1000 pF) to ground. 4, 5 GND 0 Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. 6 NC No connection. This pin should be left open. 7 OUT 1.0 to 4.7 Divided frequency output pin. This pin should be coupled to load device with a capacitor (eg 1000 pF). 8 NC No connection. This pin should be left open. ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS UNITS RATINGS VCC Supply Voltage V 6.0 VIN Input Voltage V 6.0 PT Total Power Dissipation2 mW 250 TOP Operating Temperature °C -40 to +85 TSTG Storage Temperature °C -55 to +150 UPB1508GV SYMBOL PARAMETER UNITS MIN TYP MAX VCC Supply Voltage V 4.5 5.0 5.5 TOP Operating Temperature °C -40 +25 +85 RECOMMENDED OPERATING CONDITIONS Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy glass PWB (T A = +85˚C). TEST CIRCUIT PIN DESCRIPTIONS Signal Generator Power Supply 5 V ±0.5 V1000 pF 1000 pF 1000 pF 1000 pF 1000 pF C2 C4 OPEN OPEN Counter HP5350B (Spectrum Analyzer) HP8665A 50 Ω 50 Ω

Supply Voltage, VCC (V) Circuit Current, I CC (mA) CIRCUIT CURRENT vs. SUPPLY VOLTAGE and TEMPERATURE TYPICAL PERFORMANCE CURVES (Unless otherwise specified, TA = 25°C) TA = -40 °C TA = +85 °C TA = +25 °C 0 6 54321 Guaranteed Operating Window TA = +25 °C VCC = 4.5 to 5.5 V VCC = 4.5 to 5.5 V +20 +10 -10 -20 -30 -40 -50 1000100 4000 -60 Guaranteed Operating Window VCC = 4.5 to 5.5 V +20 +10 -10 -20 -30 -40 -50 1000100 4000 -60 TA = -40 °C TA = +85 °C TA = +25 °C TA = +85 °C TA = +25 °C TA = -40 °C -10 -12 -14 -16 1000 4000100 VCC = 5.0 V PIN = 0 dBm ZL = 50 Ω TA = +85 °C TA = +25 °C TA = +85 °C TA = +25 °C TA = -40 °C TA = -40 °C UPB1508GV TA = +25 °C PIN = 0 dBm ZL = 50 Ω VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V -10 -12 -14 -16 1000 4000100 TA = -40 °C PIN = 0 dBm ZL = 50 Ω VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V -10 -12 -14 -16 1000 4000100 Input Frequency, fin (MHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Input Frequency, fin (MHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE Input Frequency, fin (MHz) Input Power, P IN (dBm) INPUT POWER vs. INPUT FREQUENCY and VOLTAGE

Input Frequency, fin (MHz) Output Power, P OUT (dBm) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE TYPICAL PERFORMANCE CURVES (Unless otherwise specified, TA = 25 °C) TA = +85 °C PIN = 0 dBm ZL = 50 Ω VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V -10 -12 -14 -16 1000 4000100 UPB1508GV FREQUENCY S 11 GHz MAG ANG 0.5 0.850 -30.2 0.6 0.796 -37.8 0.7 0.790 -39.2 0.8 0.754 -45.2 0.9 0.766 -53.7 1.0 0.701 -57.6 1.1 0.660 -62.3 1.2 0.606 -67.2 1.3 0.571 -70.3 1.4 0.521 -70.6 1.5 0.495 -68.3 1.6 0.441 -60.6 1.7 0.479 -45.1 1.8 0.602 -62.3 1.9 0.595 -74.2 2.0 0.608 -82.9 2.1 0.603 -89.8 2.2 0.599 -97.3 2.3 0.588 -107.7 2.4 0.532 -122.0 2.5 0.396 -132.0 2.6 0.325 -127.1 2.7 0.270 -123.6 2.8 0.232 -122.7 2.9 0.258 -105.8 3.0 0.351 -103.7 TYPICAL SCATTERING PARAMETERS (TA = 25 °C) S11 Z REF 1.0 Units 200.0 mUnits/ 34.604 Ω -26.496 Ω hp C D MARKER 4 : 0.5 GHz : 1.0 GHz : 2.0 GHz : 3.0 GHz S11 vs. INPUT FREQUENCY VCC = 5.0 V START 0.500000000 GHz STOP 3.000000000 GHz

0.25 0.526 118.9 0.30 0.463 131.2 0.35 0.466 124.7 0.40 0.460 117.1 0.45 0.441 110.2 0.50 0.456 103.0 0.55 0.353 94.8 0.60 0.438 91.1 0.65 0.444 83.9 0.70 0.436 78.3 0.75 0.435 71.8 0.80 0.431 65.9 0.85 0.431 60.3 0.90 0.431 53.7 0.95 0.408 49.2 1.00 0.445 44.9 1.05 0.428 41.0 1.10 0.429 33.7 1.15 0.355 42.7 1.20 0.418 20.0 1.25 0.403 17.1 1.30 0.392 9.6 1.35 0.368 3.3 1.40 0.343 -3.4 1.45 0.319 -9.2 1.50 0.289 -14.1 TYPICAL SCATTERING PARAMETERS (TA = 25 °C) S22 Z REF 1.0 Units 200.0 mUnits/ 87.789 Ω -13.633 Ω hp C D MARKER 4

1.5 GHZ 1

: 0.25 GHz : 0.50 GHz : 1.00 GHz : 1.50 GHz FREQUENCY S 22 GHz MAG ANG 0.25 0.555 146.6 0.30 0.545 139.9 0.35 0.571 136.1 0.40 0.529 127.9 0.45 0.521 122.4 0.50 0.515 116.9 0.55 0.510 104.5 0.60 0.492 106.6 0.65 0.487 100.9 0.70 0.482 95.3 0.75 0.473 89.9 0.80 0.461 83.8 0.85 0.454 78.4 0.90 0.449 72.3 0.95 0.430 69.6 1.00 0.443 64.3 1.10 0.440 52.3 1.15 0.438 46.0 1.20 0.501 37.5 1.25 0.408 32.9 1.30 0.388 25.1 1.35 0.359 16.3 1.40 0.335 9.7 1.45 0.304 3.1 1.50 0.285 4.6 S22 Z REF 1.0 Units 200.0 mUnits/ 91.109 Ω 2.6523 Ω hp C D 2 MARKER 4

1.5 GHZ

: 0.25 GHz : 0.50 GHz : 1.00 GHz : 1.50 GHz S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 3002 MHz S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 498 MHz START 0.250000000 GHz STOP 1.500000000 GHz START 0.250000000 GHz STOP 1.500000000 GHz

ORDERING INFORMATION

Note: 1. Embossed tape 8 mm wide. Pin 1 is in the tape pull-out direction. PART NUMBER QUANTITY UPB1508GV-E1-A 1000/Reel OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S08 PIN CONNECTIONS 1. VCC 2. IN 3. IN 4. GND 5. GND 6. NC 7. OUT 8. NC 8 7 6

3.0 MAX

N 1.5±0.1

1.8 MAX

0.1 ± 0.1 0.3+0.10 -0.05

0.575 MAX

0.15+0.10 -0.05 4.94 ± 0.2 3.2±0.1 0.87±0.2 0.5 ± 0.2 0.65 3 +7˚ -3˚ Detail of Lead End 0.15 1508 PIN CONNECTION SYSTEM APPLICATION EXAMPLE 1st IF Input from DBS Converter Baseband Output BPF SAW OSC LPF Prescaler AGC Amp. UPB1508GV PLLsynth. for VHF/UHF band FM Demo. MIX EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 09/21/2000DATA SUBJECT TO CHANGE WITHOUT NOTICE Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A -AZLead (Pb) < 1000 PPM Not Detected (*) Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substan ce content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway t o better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and ac curate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.