DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
１．Scope ２．Specification (Note1) (Note2) (Note3) (Note4) This document applies to Blower TF029B-1000-F (hereinafter referred to as "PRODUCT"), a product of NIDEC COPAL ELECTRONICS CORP. (hereinafter referred to as "NCEL"). Unless otherwise specified, the environmental conditions are 23℃±5℃，normal humidity, and atmospheric pressure range 90 to 106kPa. Measuring conditions : Driving circuit = NCEL's standard driving circuit, Supply voltage = DC24V, measurement equipment = NCEL's standard equipment NIDEC COPAL ELECTRONICS CORP. 18 Specifications Model No. TF029B-1000-F Issuing Date Aug.1, 2017
2 Direction of
Rotation CCW (Counter-Clockwise) Looking down from the air inlet.
3 Kind of Gas Air Noncorrosive gas
Please contact us if you'd like to operate the PRODUCT outside of specifications. No. Items Specification Remarks
1 Rated Voltage DC 12 〜 27 V
6 Number of Poles 4 Poles (2 pole pairs)
7 Drive System 3 Phase, Bipolar
4 Configuration Motor with Centrifugal Blade Without driving circ uit
5 Type of Motor DC Brushless Motor
11 Mounting
Shaft vertical to ground, air inlet facing upwards No vibration, shock, or gyration is to be applied during operation.
10 Outline Drawing ︓ 6405-00151-01 Please refer to attached
drawing.
8 Bearings Aero-Dynamic Bearings
9 Impeller Centrifugal Turbo Blade
The below specifications specify the characteristics of the Blowers at the time of shipment. The characteristics may change over time depending on the usage conditions and environment.
max. (Note4) ohm ohm max. (reference value)
14 Rated Power
Consumption 14.9 W at 2.0kPa, 100L/min, DC 24Vmax. 17 Rated Pressure 2.0 kPa (≒20 cmH2O） at 100L/min 15 Rated Air Flow 100 L/min at 2.0kPa
16 Minimum Air Flow 10 L/min
max.
20 Min．Rotation
Speed 10,000 r/min
13 Rated Power
Supply Current 0.62 A at 2.0kPa, 100L/min, DC 24V
18 Maximum
Pressure 3.5 kPa (≒35 cmH2O） Absolute maximum pressure. NIDEC COPAL ELECTRONICS CORP. 28 No. Items Specification Remarks
19 Rated Rotation
Speed 36,000 r/min at 2.0kPa, 100L/min 12 Max. Input Coil Current 2.0 A rms In continuous operation. Excluding inrush current.
21 Max．Rotation
Speed 50,000 r/min Pressure-air flow must be within the "area of use" specified in "5. Operating Range" on P.5.
22 Torque Constant (reference
value) 0.0014 ~ 0.0020 N･m/A
23 Acoustic Audible
Noise 65.0 dB(A )max. at 2.0kPa, 100L/min. Measured at 1m from air inlet. Include background noise 15dB(A).
24 Coil Resistance at 20℃ （Between 2 phase)
(reference value) (reference value）
28 Dielectric
Strength Leak current to be less than 1mA. AC600V for 1sec. between terminal pins and shaft holder. JIS C 4003
29 Weight 55 g
10 g･cm (reference value) 0.37 ~ 0.49 (reference value) Maximum axial force applying to the intake (upper housing)
25 Coil Inductance 22 ~ 29 μH at 20℃, 10kHz
(Between 2 phase)
26 Insulation Class Class E JIS C 4003
30 Rotor Inertia
27 Insulation
Resistance 1M min. DC500V,between terminal pins and shaft holder. JIS C 4003 31 Max. Axial Loading 3N
-20 to 60℃ 0 to 50℃
33 Operating
Humidity Range 10 to 95%RH No condensation No. Items Specification Remarks
37 Resistance to
The Blower shall satisfy Specification No.12 〜 28 after the following test. Non-operating Acceleration 294m/s2（30G） Pulse Width 6ms Shock Wave Semi-sinusoidal wave @ acceleration 19.6m/s2 (2G) Sweep To-and-fro, approx. 5min. Test Time X, Y, Z directions, 60min. each NIDEC COPAL ELECTRONICS CORP.
36 Resistance to
The Blower shall satisfy Specification No.12 〜 28 after the following test. Non-operating Kind of Vibration Sweep Frequency Range 10〜22Hz @ amplitude 1mm 22〜50Hz
35 Storage
Humidity Range 10 to 95%RH No condensation Operating Temperature Range Storage Temperature Range Number of Shock X, Y, Z, directions, once per each direction
３．Interface : TDK Corp. : NTCG164BH103JT ４． Timing Chart [deg] Electrical de gree [deg] Mechanical degree NIDEC COPAL ELECTRONICS CORP. 4
1 U Brown Motor Coil (U)
2 V Red Motor Coil (V)
Pin No. Symbol Wire Color Signal U V W 0 60 120 Part No. (Note5) Thermistor Manufacturer and Part No. Manufacturer
3 W Orange Motor Coil (W)
4 TH(-) Yellow Thermistor Output（－）
5 TH(+) Green Thermistor Output(+)
５．Operating Range The following graph is provided for reference only. Values are not guaranteed. Operating Range at DC24V (1atm) Area of use Operating Range at DC12V (1atm) Area of use NIDEC COPAL ELECTRONICS CORP. 58 Conditions: Ambient temperature 23±5℃, normal humidity, atmospheric pressure (100± 2kPa). Make sure the thermistor temperature does not exceed 80℃ during blower operation. (Thermistor resistance value R(80 deg C)=1.177kΩ) 0.0 1.0 2.0 3.0 4.0 0 20 40 60 80 100 120 140 160 Pressure [kPa] Air Flow [L/min] 38,500r/min 36,000r/min 26,700r/min 0.0 1.0 2.0 3.0 4.0 0 20 40 60 80 100 120 140 160 Pressure [kPa] Air Flow [L/min] 36,000r/min 26,700r/min
６．Manufacturing Code T F029B -1000-F □□□□ - □□□□ Serial Number Control number : al phabet (A - Z) Date of manufacture : refer to Chart 1 below Month of manufacture : refer to Chart 2 below Year of manufacture : last di git of the year (A.D.) 【Chart 1】 【Chart 2】 ７．Warranty ７-１．Warranty Period Warranty period of the PRODUCT is 1 year from delivery. ７-２．Warranty Scope (1) (2) 18 19 20 Code 123456 12 13 14 15 16 176789 1 0 1 1Date 12345 NIDEC COPAL ELECTRONICS CORP. 30 3126 27Date 21 22 23 24 25 VWX Y 28 29 9AB KL DEFGHJ78 C Code MNP Q RTU 2345 9OND In case a defect is found in the PRODUCT during the above warranty period and NCEL is responsible for the defect, NCEL will either repair or replace the defected PRODUCT free of charge. However, in the following cases, the PRODUCT will not be covered by warranty. Code 12345678 6789 1 0 1 1Month 1 Defects caused by inappropriate conditions, environments, handlings, and use which are not specified in this specification. Defects caused by your equipments and/or software. Defects caused by modifications and/or repairs which were not done by NCEL. Defects which could have been avoided if the PRODUCT was used accordin gly to this specification. Defects which were unpredictable with the scientific or technical level of NCEL at the time of shipment. Defects caused by external factors such as natural hazards (fire, earthquakes, floods) or electrical surges. NCEL will be responsible for the PRODUCT only in which the coverage will be limited to Clause 7-2. (1). NCEL shall not be liable for customer's equipment damages, opportunity losses, or lost earnings caused by defects of the PRODUCTS. The user shall indemnify NCEL and hold NCEL harmless from any liability or damage whatsoever arising out of any action not in accordance with this specification.
７-３．Product Application ８．Notes (1) All values are measured with NCEL's standard equipments unless otherwise specified. (2) The PRODUCT is compliant with RoHS directives which went into effect July, 2011. (3) (4) (5) (6) Please provide safety measures to prevent damages in case of product failures. (7) (8) (9) Please do not use the PRODUCT in applications to protect the body. (10) Please protect the PRODUCT from condensation. (11) Please use the correct supply voltage to operate the PRODUCT. (12) Do not disassemble or modify the PRODUCT. (13) Turn off the power immediately and stop using the PRODUCT in the following cases.
- In case water or foreign substances get into the PRODUCT.
- In case the PRODUCT is dropped or the housing is broken.
- In case unusual odor, abnormal noise, or smoke are generated from the PRODUCT. (14) Do not use or store in the following conditions;
- Humid, dusty, or poorly-ventilated area.
- Areas where the temperature is expected to rise (direct sunlight, etc.).
- Areas with corrosive gas or flammable gas in the surrounding air.
- Areas where vibration, shock, or rocking motion is applied directly to the PRODUCT.
- Areas where the PRODUCTS may be splashed with water, oil, or chemicals.
- Areas where static electricity can easily be built up. (15) Make sure the wiring is done properly. (16) (17) Install the PRODUCT using cushioning materials such as vibration dampeners. Please contact us if you have any questions regarding installation. Turn off the power of the PRODUCT and any equipment attached to the PRODUCT when putting on or taking off the cables. The PRODUCT is designed and manufactured for general-purposes. Please do not use in applications such as nuclear power, aviations, railroads, or medical equipment where great effect to human lives or wealth are expected. However,if NCEL agree with the customer the usage of the PRODUCT in such applications, NCEL will warrant the PRODUCT in the same scope described in "7. Warranty" in this specification. Performance cannot be guaranteed in case the PRODUCT is used beyond the specification or the PRODUCT is modified. Depending on the conditions or the environment, functions or performances of the PRODUCT ma y not be satisfied when the PRODUCT is used with other equipments. The PRODUCT is compliant with Directive 2006/122/EC of the European Parliament (Council Directive 76/769/EEC（30th amendment)) which restricts the use of PFOS. Please check if the PRODUCT operates normally at every start-up and during operation. Designated hazardous substances are lead, mercury, cadmium, hexavalent chrome, brominated flame retardants (PBB, PBDE) and its compounds. NIDEC COPAL ELECTRONICS CORP. 78 Contents of this document may be changed without notice. The production of the PRODUCT may be discontinued without notice. Please confirm with your local contact before ordering.
(18) (19) (20) The resin parts constituting the PRODUCT use non-flame-retardant grade. NIDEC COPAL ELECTRONICS CORP. 8 Do not block the air inlet and outlet (3 places). Please contact us if you have any questions regarding the air inlet and outlet. Vibration or audible noise level may change over time due to contamination of the blade. Please provide dust-proof constructions around the PRODUCT.