STG-12-S1 ERAVANT | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Final Rev 1.5 E-Band Noise Figure and Gain Test Extenders STG-12-S1 is an E-Band noise figure and gain test set that extends the noise and gain measurement capabilities of common and low frequency signal synthesizers and noise figure meters to the frequency range of 60 to 90 GHz. This extender is designed to interface with industry standard noise and gain test systems, such as the Keysight 8970A/B and Y Factor measurements with a spectrum analyzer. It can also interface with most noise and gain analyzers in the 10.0 MHz to 1.6 GHz frequency range. Electrical Specifications: Mechanical Specifications: Parameter Minimum Typical Maximum RF Frequency 60 GHz 90 GHz Noise Source ENR 15 dB Noise Source Bias Voltage/Current +15 VDC +28 VDC/90 mA Down Converter IF Frequency 10 MHz 1.6 GHz Down Converter LO Frequency/Power 10 GHz 15 GHz Down Converter LO Input Power +3 dBm +20 dBm Down Converter RF Damage Level +18 dBm Down Converter Gain 20 dB Power Supply (AC Adapter Provided) 100 VAC 240 VAC Specification Temperature +25 °C Operating Temperature 0 °C +50 °C Item Specification Noise Source RF Ports WR-12 Waveguide with UG-387/U-M Compatible Anti-Cocking Flange Noise Source Bias Port BNC (F) Noise Source Trigger SMA (F) Down Converter RF Port WR-12 Waveguide with UG-387/U-M Precision Anti-Cocking Flange Down Converter LO Port SMA (F) Down Converter IF Port SMA (F) Down Converter Bias Port 2.5 mm DC Jack (AC-to DC power converter included) Weight 4 lbs Outline Down Converter (TC-E-A) Noise Source (TZ-WE-A) ECCN EAR99
FEATURES
- Full Band Coverage
- Precision Calibrated ENR
- Great ENR and Gain Flatness
APPLICATIONS
- Test Lab
- Instrumentations SUPPLEMENTAL DETAILS
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Final Rev 1.5 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 Conversion Gain (dB) Frequency (GHz) Typical Conversion Gain vs. Frequency IF: 1 GHz, LO: +3 dBm, RF: -40 dBm 60 65 70 75 80 85 90 ENR (dB) Frequency (GHz) ENR vs. Frequency
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Final Rev 1.5 Down Converter Mechanical Outline: Unless otherwise specified, all dimensions are in inches [millimeters]) Noise Source Mechanical Outline: Unless otherwise specified, all dimensions are in inches [millimeters])
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Final Rev 1.5 NOTE:
- All data presented is collected from a sample lot. Actual data may vary unit to unit.
- All testing was performed under +25 ˚C case temperature.
- The Triggering Port (female SMA connector) of the noise source is provided to turn the noise source on and off via a TTL control signal any time the Bias is applied. The switching frequency is limited to 1 KHz.
- The Power/Triggering Inversion Switch of the noise source is provided to manually turn the noise source on and off any time the Bias is applied. When the switch is in the “ON” position, the LED light will be illuminated.
- Eravant reserves the right to change the information presented without notice. CAUTION:
- Exceeding absolute maximum ratings shown will damage the device.
- Any foreign objects in the waveguide will cause performance degradation and possible device damage.