STG-06-S1 ERAVANT | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Advanced Rev 1.7 D-Band Noise Figure and Gain Test Extenders STG-06-S1 is a full D-Band noise figure and gain test extender that extends the noise and gain measurement capabilities of common and low frequency signal synthesizers and noise figure meters to the frequency range of 110 to 170 GHz. This extender is designed to interface with industry standard noise and gain test systems, such as Keysight 8970A/B and Y Factor with a spectrum analyzer. It can also interface with most noise and gain analyzers in the 10.0 MHz to 1.6 GHz frequency range. Electrical Specifications: Parameter Minimum Typical Maximum RF Frequency 110 GHz 170 GHz Noise Source ENR 12 dB Noise Source Bias Voltage/Current +18 VDC/ 50 mA +28 VDC/ 60 mA +30 VDC/ 75 mA Down Converter IF Frequency 10.0 MHz 1.6 GHz Down Converter LO Frequency/Power
9.16 GHz/
+3 dBm
11.6 GHz/
+5 dBm
14.17 GHz/
+20 dBm Down Converter LO Damage Level +20 dBm Down Converter RF Damage Level +15 dBm Down Converter Noise Figure 16 dB Down Converter Gain 20 dB Down Converter Bias Voltage +8 VDC +12 VDC +15 VDC Down Converter Bias Current 450 mA Specification Temperature +25 ˚C Operating Temperature 0 ˚C +50 ˚C ECCN 3A001.b.7
FEATURES
- Full Band Coverage
- Precision Calibrated ENR
- Great ENR and Gain Flatness
APPLICATIONS
- Test Lab
- Instrumentations SUPPLEMENTAL DETAILS
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Advanced Rev 1.7 Mechanical Specifications: Item Specification Noise Source RF Port WR-06 Waveguide with UG-387/U-M Anti-Cocking Flange Noise Source Bias Port BNC (F) Noise Source Trigger SMA (F) Down Converter RF Port WR-06 Waveguide with UG-387/U-M Precision Anti-Cocking Flange Down Converter LO Port SMA (F) Down Converter IF Port SMA (F) Down Converter Bias Port Banana Jack Weight 4.0 lbs. Outline Down Converter (TC-D-A), Noise Source (TZ-WD-A) 110 120 130 140 150 160 170 ENR (dB) Frequency (GHz) Typical ENR vs. Frequency VDC= +28 V, IDC= 60 mA
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Advanced Rev 1.7 Down Converter Mechanical Outline: Unless otherwise specified, all dimensions are in inches [millimeters]) Noise Source Mechanical Outline: Unless otherwise specified, all dimensions are in inches [millimeters])
www.eravant.com | 424-757-0168 | support@eravant.com Copyright © 2023 by Eravant Advanced Rev 1.7 NOTE:
- All data presented is collected from a sample lot. Actual data may vary unit to unit.
- All testing was performed under +25˚C case temperature.
- The Triggering Port (female SMA connector) of the noise source is provided to turn the noise source on and off via a TTL control signal any time the Bias is applied. The switching frequency is limited to 1 KHz.
- The Power/Triggering Inversion Switch of the noise source is provided to manually turn the noise source on and off any time the Bias is applied. When the switch is in the “ON” position, the LED light will be illuminated.
- Eravant reserves the right to change the information presented without notice. CAUTION:
- Exceeding absolute maximum ratings shown will damage the device.
- Any foreign objects in the waveguide will cause performance degradation and possible device damage.