PS9822-2-F3-AX

PS9822-1 CEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. PHOTOCOUPLER PS9822-1,-2 Document No. PN10698EJ01V0DS (1st edition) Date Published January 2008 NS

1 Mbps OPEN COLLECTOR OUTPUT TYPE

8-PIN SSOP (SO-8) HIGH-SPEED PHOTOCOUPLER −NEPOC Series− 2008 1234 8765 PS9822-1 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. V O 7. NC 8. VCC 1234 8765 SHIELD SHIELD PS9822-2 1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. V 7. VO1 8. VCC PIN CONNECTION (Top View)

DESCRIPTION

The PS9822-1 and PS9822-2 are active-low type high-speed photocouplers that use a GaAlAs light-emitting diode on the input side and a photodetector IC that includes a photodiode and a signal processor on the same chip on the output side. The PS9822-1, -2 are high-speed digital output type photocouplers designed specifically for low circuit current. The PS9822-2 is suitable for high density applications.

FEATURES

• Supply Voltage N rank: VCC = 3.3 V L rank: VCC = 5 V
• Pulse width distortion ( ⏐tPHL−tPLH⏐ = 200 ns MAX.)
• 40% reduction of mounting area (5-pin SOP × 2)
• High-speed (1 Mbps)
• High isolation voltage (BV = 2 500 Vr.m.s.)
• Open collector output
• Ordering number of tape product : PS9822-1-F3: 1 500 pcs/reel leer/scp 005 1 :3F-2-2289SP :
• Pb-Free product

APPLICATIONS

• PoE (Power over Ethernet)
• Measurement equipment
• FA Network TRUTH TABLE LED Output ON L OFF H

Preliminary Data Sheet PN10698EJ01V0DS 2 PS9822-1,-2 PACKAGE DIMENSIONS (UNIT: mm) 3.95±0.1 6.0±0.2 0.5±0.3 0.15+0.10 –0.05 0.10 S 1.27 0.1±0.1 3.27±0.2 5.21±0.25 MARKING EXAMPLE No. 1 pin Mark Initial of NEC (Engraved mark) PS9822-1 PS9822-2 No. 1 pin Mark Initial of NEC (Engraved mark) N 9822-2 NT731 Week Assembled Assembly Lot N 9822-1 NT731 7 31 Year Assembled (Last 1 Digit) TN Rank Code In-house Code (T: Pb-Free) 7 31 Year Assembled (Last 1 Digit) TN Rank Code In-house Code (T: Pb-Free) Week Assembled Type Number Assembly Lot Type Number

Preliminary Data Sheet PN10698EJ01V0DS 3 PS9822-1,-2

ORDERING INFORMATION

Part Number Order Number Rank Solder Plating Specification Packing Style N PS9822-1 PS9822-1-AX L Pb-Free 20 pcs (Tape 20 pcs cut) N PS9822-1-F3 PS9822-1-F3-AX L Embossed Tape 1 500 pcs/reel N PS9822-2 PS9822-2-AX L 20 pcs (Tape 20 pcs cut) N PS9822-2-F3 PS9822-2-F3-AX L Embossed Tape 1 500 pcs/reel *1 N rank: VCC = 3.3 V *2 L rank: VCC = 5 V

Preliminary Data Sheet PN10698EJ01V0DS 4 PS9822-1,-2 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Symbol Ratings Unit 2-2289SP 1-2289SP Diode Forward Current I F 20 mA Reverse Voltage V R 5 V/ch Detector Supply Voltage V CC 7 V Output Voltage V O 7 V/ch Output Current I O 25 mA/ch Power Dissipation P C 40 mW/ch Isolation Voltage .s.m.rV 005 2 VB Operating Ambient Temperature T A −40 to +100 °C Storage Temperature T stg −55 to +125 °C *1 Reduced to 0.3 mA/ °C at TA = 60°C or more. *2 Reduced to 0.1 mA/ °C at TA = 60°C or more. *3 Applies to output pin V O (collector pin). Reduced to 1.5 mW/°C at TA = 65°C or more. *4 AC voltage for 1 minute at T A = 25°C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. TYP. MAX. Unit Low Level Input Voltage V FL 0 0.8 V High Level Input Current I FH 6.3 10 12.5 mA Supply Voltage N rank V CC 2.7 3.3 3.6 V 5.5 0.5 5.4 knar L R ecnatsiseR pu-lluP L 330 4 k Ω TLL (RL = 1.0 kΩ, loads) N 5

Preliminary Data Sheet PN10698EJ01V0DS 5 PS9822-1,-2 ELECTRICAL CHARACTERISTICS: N rank (TA = −40 to +100°C, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. MAX. Unit Diode Forward Voltage V F I F = 10 mA, TA = 25°C 1.6 1.8 V Reverse Current I R V R = 3 V, TA = 25° 01 C μA Terminal Capacitance C t V = 0 V, f = 1 MHz, T A = 25°C 30 pF Detector High Level Output Current I OH V CC = VO = 3.3 V, VF = 0.8 V 1 100 μA Low Level Output Voltage V OL V CC = 3.3 V, IF = 5 mA, IOL = 13 mA 0.2 0.6 V High Level Supply Current I CCH V CC = 3.3 V, IF = 0 mA, VO = Open 2 mA/ch Low Level Supply Current I CCL V CC = 3.3 V, IF = 10 mA, VO = Open 3 Coupled Threshold Input Current (H → L) IFHL V CC = 3.3 V, VO = 0.8 V, RL = 350 Ω 5 mA Isolation Resistance R I-O V I-O = 1 kVDC, RH = 40 to 60%, TA = 25°C Ω Isolation Capacitance C I-O V = 0 V, f = 1 MHz, T A = 25°C 0.6 pF Propagation Delay Time (H → L) tPHL V CC = 3.3 V, RL = 350 Ω, IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 500 ns Propagation Delay Time (L → H) tPLH 007 Pulse Width Distortion (PWD) ⏐tPHL-tPLH⏐ V CC = 3.3 V, RL = 350 Ω, IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 200 ns *1 Typical values at T A = 25°C *2 Because V OL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device.

Preliminary Data Sheet PN10698EJ01V0DS 6 PS9822-1,-2 ELECTRICAL CHARACTERISTICS: L rank (TA = −40 to +100°C, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. MAX. Unit Diode Forward Voltage V F I F = 10 mA, TA = 25°C 1.6 1.8 V Reverse Current I R V R = 3 V, TA = 25° 01 C μA Terminal Capacitance C t V = 0 V, f = 1 MHz, T A = 25°C 30 pF Detector High Level Output Current I OH V CC = VO = 5 V, VF = 0.8 V 1 100 μA Low Level Output Voltage V OL V CC = 5 V, IF = 5 mA, IOL = 13 mA 0.2 0.6 V High Level Supply Current I CCH V CC = 5 V, IF = 0 mA, VO = Open 2.5 mA/ch Low Level Supply Current I CCL V CC = 5 V, IF = 10 mA, VO = Open 3.5 Coupled Threshold Input Current (H → L) IFHL V CC = 5 V, VO = 0.8 V, RL = 350 Ω 5 mA Isolation Resistance R I-O V I-O = 1 kVDC, RH = 40 to 60%, TA = 25°C Ω Isolation Capacitance C I-O V = 0 V, f = 1 MHz, T A = 25°C 0.6 pF Propagation Delay Time (H → L) tPHL V CC = 5 V, RL = 350 Ω, IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 500 ns Propagation Delay Time (L → H) tPLH 007 Pulse Width Distortion (PWD) ⏐tPHL-tPLH⏐ V CC = 5 V, RL = 350 Ω, IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 200 ns *1 Typical values at T A = 25°C *2 Because V OL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device.

Preliminary Data Sheet PN10698EJ01V0DS 7 PS9822-1,-2 TAPING SPECIFICATIONS (UNIT: mm) 4.05 MAX. Outline and Dimensions (Reel) Packing: 1 500 pcs/reel 2.0±0.5 R 1.0 13.0±0.2φ 21.0±0.8φ 330±2.0φ 100±1.0φ 2.0±0.5 11.9 to 15.4 Outer edge of flange 17.5±1.0 13.5±1.0 13.0±0.2φ 1.7±0.1 2.0±0.05 4.0±0.1 1.75±0.1 6.4±0.1 5.56±0.1 0.3±0.058.0±0.1 1.5+0.1 5.5±0.1 12.0±0.2 3.6±0.1 Outline and Dimensions (Tape) Taping Direction PS9822-1-F3 PS9822-2-F3

Preliminary Data Sheet PN10698EJ01V0DS 8 PS9822-1,-2 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) 1.45 0.81.27 5.25

Preliminary Data Sheet PN10698EJ01V0DS 9 PS9822-1,-2 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering 062 erutarepmet wolfer kaeP • °C or below (package surface temperature)

• Time of peak reflow temperature 10 seconds or less
• Time of temperature higher than 220°C 60 seconds or less
• Time to preheat temperature from 120 to 180°C 120 ±30 s eerhT swolfer fo rebmuN • llams gniniatnoc xulf nisoR xulF • amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) 120±30 s (preheating) 220˚C 180˚C Package Surface Temperature T (˚C) Time (s) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s to 60 s 260˚C MAX. 120˚C (2) Wave soldering
• Temperature 260 °C or below (molten solder temperature)
• Time 10 seconds or less
• Preheating conditions 120 °C or below (package surface temperature)
• Number of times One (Allowed to be dipped in solder including plastic mold portion.)
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron
• Peak temperature (lead part temperature) 350 °C or below
• Time (each pins) 3 seconds or less llams gniniatnoc xulf nisoR xulF • amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100°C.

Preliminary Data Sheet PN10698EJ01V0DS 10 PS9822-1,-2 (4) Cautions

• Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 μF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity.

Preliminary Data Sheet PN10698EJ01V0DS 11 PS9822-1,-2 The information in this document is current as of January, 2008. The information is subject to change without notice. For actual design-in, refe r to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in t his document. NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such pr oducts. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Elec tronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possib ility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate suffic ient safety measures in their design, such as redundancy, fire-containment and anti-failure features. NEC Electronics products are classified into the following three quality grad es: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electroni cs products developed based on a customer- designated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. The quality grade of NEC Electr onics pr oducts is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electr onics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) M8E 02. 11-1 (1) (2) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. "Standard": "Special": "Specific":

PS9822-1,-2 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points.

• Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.