PS9711-E4

PS9711 CEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

HIGH SPEED 10 Mbps, TOTEM-POLE OUTPUT TYPE

5 PIN SOP TOM OPTOCOUPLER

DESCRIPTION

The PS9711 is an optically coupled high speed totem pole isolator containing a GaAIAs LED on the light emitting diode side (input side) and a photodiode and a signal processing circuit on the light receiving side (output side) on one chip. It is housed in a plastic SOP (Small Out-Line Package) for high density applications.

• COMPUTER AND PERIPHERAL DEVICES
• MEASUREMENT EQUIPMENT
• POWER SUPPLY

FEATURES

• HIGH COMMON MODE TRANSIENT IMMUNITY CMH, CML: ±10 kV/µs TYP
• SMALL PACKAGE 5 pin SOP
• HIGH SPEED RESPONSE tPHL = 30 ns, tPLH = 35 ns TYP
• PULSE WIDTH DISTORTION |tPHL-tPLH| = 7 ns TYP
• TOTEM-POLE OUTPUT No Pull-up resistor required
• TAPE AND REEL AVAILABLE

APPLICATIONS

SYMBOLS PARAMETERS UNITS MIN TYP MAX VF Forward Voltage, IF = 10 mA, TA = 25°CV 1.4 1.65 1.9 IR Reverse Current, VR = 3 V, TA = 25°C µA1 0 Ct Capacitance, V = 0, f = 1.0 MHz, TA = 25°Cp F 3 0 IOH High Level Output Current, VCC = VO = 5.5 V, IF = 250 µA µA1 200 VOH High Level Output Voltage, VCC = 4.5 V, IF = 250 µA, IOH = -2 mA V 2.4 3.0 VOL Low Level Output Voltage, VCC = 4.5 V, IF = 7 mA, IO = 8 mA V 0.38 0.6 ICCH High Level Supply Current, VCC = 5.5 V, IF = 0 mA mA 11 17 ICCL Low Level Supply Current, VCC = 5.5 V, IF = 10 mA mA 12 18 IOSH High Level Output Short Circuit Current, VCC = 5.5 V, VO =GND, IF = 0 mA, 10 ms or less mA -26 IOSL Low Level Output Short Circuit Current, VCC = 5.5 V, VO =GND, IF = 8 mA, 10 ms or less mA 34 IFHL Threshold Input Current, High → Low, VCC = 5 V TA = 25°Cm A 2.0 5 IFLH Threshold Input Current, Low → High, VCC = 5 V TA = 25°Cm A 0.5 0.35 RI-O Isolation Resistance, Vin-out = 1 kVDC, RH = 40 to 60%, TA = 25°C Ω 1011 CI-O Isolation Capacitance, V = 0, f = 1.0 MHz, TA = 25°Cp F 0.6 tPHL Propagation Delay Time, High → Low2 , VCC = 5 V, IF = 7.5 mA ns 15 30 65 TA = 25°C1 0 8 5 tPLH Propagation Delay Time, Low → High2 ,VCC = 5 V, IF = 7.5 mA ns 15 35 65 TA = 25°C1 0 8 5 |tPHL-tPLH| Pulse Width Distortion, (PWD)2,VCC = 5 V, IF = 7.5 mA ns 7 35 CMH Common Mode Transient Immunity at High Level Output3 kV/µs1 1 0 VCC = 5 V, TA = 25°C, IF = 0 mA, VO(min) = 2 V , VCM = 100 V CML Common Mode Transient Immunity at Low Level Output3 kV/µs1 1 0 VCC = 5 V, TA = 25°C, IF = 7.5 mA, VO = 0.8 V (max) RL = 350 Ω VCM = 1 kV ELECTRICAL CHARACTERISTICS (TA = -40 to +85 °C, unless otherwise specified) Detector Diode Coupled SEE NOTES ON NEXT PAGE California Eastern Laboratories

CL is approximately 15 pF, which includes probe and stray wiring capacitance. 1. Typical Values at TA = 25°C. 2. Test Circuit for Propagation Delay Time: Input VON Output IF (ON) 50% IF (ON) 1.5 V VOL tPLHtPHL 3. Test Circuit for Common Mode Transient Immunity Input Monitor Pulse Input (IF) VCC = 5 VVCC = 5 V VO (Monitor) *CL = 30pF 0.1 µF 47 Ω 2.5 kΩ 1.3 kΩ PW = 500 ns Duty Cycle = 1/2( ) VCC GND C L = 15 pF GL SW IF VCC = 5 V VO (Monitor) C L = 15pF 0.1 µF VCC GND 90% 10% 0.8 V VOL tftr VCM VO VO VOH 100 V 0 V 2 V IF = 7.5 mA IF = 0 mA ELECTRICAL CHARACTERISTICS NOTES: CL is approximately 15 pF, which includes probe and stray wiring capacitance. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 µF is used between VCC and GND near device. PART NUMBER PS9711 SYMBOLS PARAMETERS UNITS MIN TYP MAX IFH High Level Input Current mA 7.5 12.5 IFL Low Level Input Current µA0 250 VCC Supply Voltage V 4.5 5.0 5.5 N TTL → RL = 1 kΩ TTL 3 RECOMMENDED OPERATING CONDITIONS PART NUMBER PACKAGE PACKING STYLE PS9711 5 Pin SOP Magazine case 100 pcs PS9711-E3 Embossed Tape 900 pcs/reel PS9711-E4 PS9711-F3 Embossed Tape 3500 pcs/reel PS9711-F4

ORDERING INFORMATION

SYMBOLS PARAMETERS UNITS RATINGS Diode VR Reverse Voltage V 3.0 IF Forward Current (DC) mA 30 Detector VCC Supply Voltage V 7 VO Output Voltage V 7 IOH High Level Output Current2 mA -5 IOL Low Level Output Current2 mA 13 PD Power Dissipation mW 130 Coupled BV Isolation Voltage 3 Vr.m.s. 2500 TSTG Storage Temperature °C -55 to +125 TA Operating Temperature °C -40 to +85 ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) Notes: 1. Operaion in excess of any one of these parameters may result in permanent damage. 3. AC voltage for 1 minute at T A = 25 °C, RH = 60 % between input and output.

OUTLINE DIMENSIONS (Units in mm) PS9711 PIN CONNECTION (Top View) 1.2 MAX 2.1±0.2 1.27 4.4 0.5 ± 0.3 7.0 ± 0.3 4.0±0.5 0.25 M0.4 +0.10 -0.05 1.3 0.15 +0.10 -0.05 0.1 ± 0.1 1. Anode 2. Cathode 3. GND 4. V O 5. V CC 543 INTERNAL OUTPUT CIRCUIT VCC (5) VO (4) GND (3) TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Ambient Temperature, TA (°C) Maximum Forward Current, I F (mA) Ambient Temperature, TA (°C) Detector Power Dissipation, Pc (mW) FORWARD CURRENT vs. FORWARD VOLTAGE Forward Voltage, VF (V) Forward Current I F (mA) SUPPLY CURRENT vs. AMBIENT TEMPERATURE Ambient Temperature, TA (°C) High Level Supply Current, I CCH (mA) Low Level Supply Current, I CCL (mA) LED OUTPUT ON L OFF H 20 40 60 80 100 85 0 100 200 20 40 60 80 100 150 0.01 0.1 1.0 100 TA = 100 ˚C 50 ˚C 25 ˚C 0 ˚C -25 ˚C VCC = 5.5 V, ICCH: IF = 0 mA ICCL: IF = 10 mA ICCL ICCH -50 -25 0 25 50 75 100

TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified) VCC = 4.5 V, IF = 250 µA TA = +85°C +25°C -40°C VCC = 4.5 V, IF = 250 µA, IOH = -2 mA -50 -25 0 25 50 75 100 TA = +85°C +25°C -40°C VCC = 4.5 IF = 7 mA 05 1 0 15 VCC = 4.5 V, IF = 7 mA, IO = 8 mA 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -50 -25 0 25 50 75 100 VCC = 5 V -10 -20 -30 0 5 10 15 20 25 tPHL tPLH PWD tPHL tPLH PWD -50 -25 0 25 50 75 100 V CC = 5 V, IF = 7.5 mA HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT High Level Output Current IOH (mA) High Level Output Voltage, V OH (V) HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE High Level Output Voltage, V OH (V) Ambient Temperature, TA (°C) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE Ambient Temperature, TA (°C) Ambient Temperature, TA (°C)Forward Current, IF (mA) Propagation Delay Time, t PHL, tPLH (ns) Pulse Width Distortion, |t PHL - t PLH | (ns) Propagation Delay Time, t PHL, tPLH (ns) Pulse Width Distortion, |t PHL - t PLH | (ns) LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT Low Level Output Current IOH (mA) Low Level Output Voltage, V OH (V) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE Low Level Output Voltage, V OH (V)

Threshold Input Current, I FHL , I FLH (mA) THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified) Ambient Temperature, TA (°C) IFHL IFLH V CC = 5 V -50 -25 0 25 50 75 100 TAPING SPECIFICATIONS (Units in mm) 13.0±1.0 φ180 φ13.0±0.5 φ21.0±0.8 φ60 φ13.0±0.5 2.0 2.0±0.5 15° 15° 4±0.1 2±0.1 1.55±0.1 4.6±0.1 8±0.1 1.55±0.1 12±0.2 5.5±0.1 1.75±0.1 2.4±0.1 0.3 7.4±0.1 TAPE OUTLINE AND DIMENSIONS TAPE DIRECTION PS9711-E3 PS9711-E4 REEL OUTLINE AND DIMENSIONS Packing: 900 pcs/reel

TAPING SPECIFICATIONS (Units in mm) 2.0 ± 0.5 1.5 ± 0.5 12.4 +2.0 -0.0 φ21.0 ± 0.8 6.0 ± 1 120 PS89701-E3, E4: φ178 PS9701-F3, F4: φ 330 φ66 φ13.0±0.5 60°

18.4 MAX

1.5 ± 0.1 1.5 ± 0.1 PS9711 4±0.1 2±0.1 1.55±0.1 4.6±0.1 8±0.1 1.55±0.1 12±0.2 5.5±0.1 1.75±0.1 2.4±0.1 0.3 7.4±0.1 TAPE OUTLINE AND DIMENSIONS TAPE DIRECTION REEL OUTLINE AND DIMENSIONS PS9711-F3 PS9711-F4 Packing: 3500 pcs/reel

RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering

• Peak reflow temperature 235 ˚C or below (package surface temperature)
• Time of temperature higher than 210 ˚C 30 seconds or less
• Number of reflows Three
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). (2) Dip soldering
• Temperature 260 ˚C or below (molten solder temperature)
• Time 10 seconds or less
• Number of times One (Allowed to be dipped in solder including plastic mold portion.)
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). (3) Cautions
• Fluxes Avoid removing the residual flux with chlorine-based cleaning solvent after a reflow process. Time (s) Package Surface Temperature T (˚C) 100 to 160 ˚C 60 to 120 s (preheating) (heating) to 10 s to 30 s 235 ˚C (peak temperature) 210 ˚C Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. A Business Partner of NEC Compound Semiconductor Devices, Ltd. 03/17/2003