PM600 ARTESYN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Voltage accuracy ±5.0%, max. Line regulation LL to HL ±0.3% Load regulation NL to FL ±0.4% Ripple and noise 20MHz BW 20mV pk-pk, max. See Note 5 Transient response Overshoot for ±0.1%, typical 10% to 90% FL Temperature coefficient ±0.01%°C, typical Short circuit protection Output thermal Continuous limited automatic recovery INPUT SPECIFICATIONS Input voltage range 5VDC, See Note 10 4.5 to 5.5VDC 12VDC, See Note 10 10.8 to 13.2VDC Input filter See Note 8 Pi network Fault current mode 150% of FL input current PM600 SERIES Single and dual output [ 2 YEAR WARRANTY ]

  • 24 pin DIP package
  • 1.25 x 0.8 x 0.4 inch package
  • Tight regulation
  • Pi input filter
  • 20mV pk-pk ripple and noise
  • Short circuit protection The PM600 Series are a broad line of low cost, high performance single and dual output DC/DC converters packaged in an IC compatible 24 pin DIP configuration. These miniature converters are ideal for use on high density PC boards, or wherever low power, isolated and regulated outputs are required. A self contained input Pi network filter, available on all models, minimizes reflected ripple current for critical applications. This feature eliminates the need for external filters thus reducing overall system cost. The PM600 series maintain ±0.3% line and ±0.4% load regulation, and require no derating over the specified operating temperature range. Other specifications include: output voltage accuracy, ±5.0%; ripple and noise, 20mV pk-pk; isolation, 300VDC. PM600 series DC/DC converters are intended for a wide variety of industrial applications, especially where tight regulation is required. SPECIFICATION All specifications are typical at nominal input, full load at 25 °C unless otherwise stated PAGE 1 GENERAL SPECIFICATIONS Efficiency 50% typical Isolation voltage 300VDC Switching frequency Variable 40kHz to 70kHz Case material UL94V-0 Non-conductive black plastic Weight 14g (0.5oz) MTBF Single Outputs 434,000 hours (75% FL) Dual Outputs 268,000 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient –25°C to +71°C Non-operating amb., –40°C to +125°C Case +95°C, max. Derating None required Cooling Free air convection cooled Relative humidity Non-condensing 20% to 95% RH Altitude Operating 10,000 feet max. Non operating 40,000 feet max. Vibration 5Hz to 500Hz 2.5G rms (approx.)
  • PM671P . 0.08 (2.0) 0.02 DIA. (0.5) 1.25 (31.8) 0.10 (2.54) 0.15 (3.8) 0.40 (10.2) 0.80 (20.3) 0.60 (15.2) CASE F (OPT.) ALL DIMENSIONS IN INCHES (mm) Notes 1 Maximum figure, at full load. 2M easured from high line to low line. 3M easured as load changes from no load to 100% full load.

4 The PM671 is available with optional voltage balance pin, and is

designated by suffix letter ‘P’. For connection information, see case drawing. In addition, both the PM671 and PM672 are available with alternate pin-out (including balance pin) designated by suffix letter ‘R’. See case drawing. If not required, the balance pin can be left floating. 5M easured with a 15µF tantalum capacitor across each output. 6 On dual output models the four common pins are internally connected. The outputs can be returned through one pin while the others remain floating.

7 Standard specifications are conservative and can be optimized for specific

applications. In particular, converter start-up at lower than specified temperature, wider input voltage range and output voltage adjustment are all relatively simple modifications to the standard product. Consult factory for details.

8 Fixed frequency design provides for easier input filtering and better noise

performance. 9 Units are tested with resistive load only. 10 Output current derates to 0 at 110% nominal Vin. 11 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. (Opt.) or Balance Pin Connection: Connect R1 as required to balance outputs when I + VoutI > I - VoutI Connect R2 as required to balance outputs when I - VoutI > I + VoutI Input to balance pin: ±5mA, max. R1 or R2: 3K Ohm, min. PIN CONNECTIONS SINGLE DUAL ALTERNATE PIN-OUTPIN OUTPUT OUTPUT SUFFIX R (4) NUMBER MODELS MODELS (6) 1 +V Input +V Input +V Input

2 Do not connect –V Output +V Input

3 Do not connect Common +V Input

9 No Pin Balance (opt)* No Pin

10 –V Output Common Common 11 +V Output +V Output Common 12 –V Input –V Input Do not connect 13 –V Input –V Input –V Output 14 +V Output +V Output Balance 15 –V Output Common +V Output

22 Do not connect Common –V Input

23 Do not connect –V Output –V Input

24 +V Input +V Input –V Input INPUT OUTPUT OUTPUT INPUT TYPICAL REGULATION MODEL VOLTAGE VOLTAGE CURRENT CURRENT (1) EFFICIENCY LINE (2) LOAD (3) NUMBER 5VDC 5VDC 100mA 260mA 50% ±0.3% ±0.4% PM621 5VDC 12VDC 80mA 380mA 50% ±0.3% ±0.4% PM623 5VDC 15VDC 65mA 380mA 50% ±0.3% ±0.4% PM624 5VDC ±12VDC ±40mA 380mA 50% ±0.3% ±0.4% PM671 (4,6) 5VDC ±15VDC ±33mA 380mA 50% ±0.3% ±0.4% PM672 (4,6) 12VDC 5VDC 100mA 100mA 50% ±0.3% ±0.4% PM631 12VDC ±12VDC ±40mA 145mA 50% ±0.3% ±0.4% PM681 (6) 12VDC ±15VDC ±33mA 145mA 50% ±0.3% ±0.4% PM682 (6) 0.5 to 1 Watt Nominal input DC/DC converters SPECIAL APPLICATION MODELS | 0.5-1W DC/DC PAGE 2http://www.artesyn.com ds_pm600_20050826.PDF Datsheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Art esyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompa ny the sale of any such product(s) or information contained herein.