DS850DC-3 ARTESYN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Distributed Power Bulk Front-End Total Output Power: 650 - 850 Watts +3.3vdc Stand-by Output Standard Telco input range -39 V to -72 VDC Special FeatureS 1U X 2U form factor 15.4W/ in3 +12Vdc output +3.3vdc stand-by (5V standby - consult factory) No minimum load required Hot plug operation N + 1 redundant Internal OR’ing fets Active current sharing 2PSU shared from 30% to 100% 4PSU shared from 20% to100% Built-in cooling fan (40mm x 28mm) I 2C communication Interface bus EEPROM for FRU data Amber/green bi-color LED status Internal fan speed control Fan fail tach output signal One year warranty SaFety UL/cUL 60950 (UL recognized) NEMKO+ CB report EN60950 CE mark China CCC Electrical Specifications Input Input ra nge: -40 Vdc to -75 Vdc Efficiency: > 80% typical Conducted EMI: FCC Subpart J EN55022 Class B Radiated EMI: FCC Subpart J EN55022 Class B Hold up time: 1 ms @48 Vdc Output Main DC voltage: +12 V @ 70 A; DS850DC +12 V @ 52.5 A; DS650DC Stand-By: +3.3 Vsb @ 6A (5V @ 4A available) Adjustment range: Factory Set, no pot adjustments Regulation: +12 Vdc; +5%/-5% +3.3 Vsb; +5%/-5% Overcurrent: +12 Vdc; 77A - 105A - DS850DC; +12 Vdc 57.75 A - 78.75 A; DS650DC latches off if overcurrent lasts over 1 second, otherwise it is auto recovery. +3.3 vsb, 9A max (hiccup mode) Overvoltage: +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc Under voltage: +12 Vdc; 9 - 10.8V (latch off) Turn-on delay: 2 Second max +12VOutput Rise Time: 10 - 300 mS, Monotonic Rise Data Sheet DC Input Connector input shown
DS650DC-3/DS850DC-3 Data Sheet Logic Control PS_SEATED TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed. PWR GOOD Active TTL HiIGH when output is within regulation limits. DC Input OK A LOW logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warning signal before 12.0v DC output loss of regulation. Temp OK A TTL logic HIGH, when operating within allowable temperature range. PS_INHIBIT/PS_KILL When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pulled low by the system and turn the power supply on. Environmental Specifications Operating temperature: 0 to 50°C, unimpeded airflow Storage temperature: -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility/Input transients: -EN61000-3-2, -3-3 -EN55024:1998 RoHS & lead-free compliant (no tantalum caps.) Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons complies with Astec Std. Specifications. MTBF (observed) 500K Hrs at 80% load
Ordering Information
Voltage Set Point Set Point Tolerance Total Regulation Minimum Current Maximum Current Output Ripple P/P DS850DC-3 12.0 Vdc
3.3 Vsb*
± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 70 A 6.0 A 120 mV 50 mV DS850DC-3-003 12.0 Vdc
5 Vsb*
± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 70 A 4.0 A 120 mV 50 mV DS850DC-3-004 (Reverse airflow)
12.0 Vdc
± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 70 A 6.0 A 120 mV 50 mV DS650DC-3 12.0 Vdc ± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 52.5 A 6.0 A 120 mV 50 mV DS650DC-3-002 12.0 Vdc ± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 52.5 A 4.0 A 120 mV 50 mV DS650DC-3-003 (Reverse airflow) ± 0.2% ± 1% ± 5% ± 5% 0 A 0 A 52.5 A 6.0 A 120 mV 50 mV
DS650DC-3/DS850DC-3 Data Sheet 5FSNJOBMCMPDLJOQVUTIPXO Mechanical Drawing Power Supply Condition LED Green/Amber No AC power to all PSU OFF AC present/Standby outpus ON, Main output OFF Blinking Green Power supply DC outputs ON and OK Solid Green Main output failure (OCP , OVP , UVP) Blinking Amber Fan Fail, OTP , Standby output OCP/UVP Solid Amber
DS650DC-3/DS850DC-3 Data Sheet WORLDWIDE OFFICES americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 europe (uK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc. www.artesyn.com DS650DC-3/DS850DC-3-DS Rev. 07.03.14 DC Output Connector Pinout Assignment Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 PB1 PB2 PB3 PB4 PB5 PB6 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 Pin Assignments Pin Signal Name PB 1 +12V RETURN PB 2 +12V RETURN PB 3 +12V RETURN PB 4 +12V PB 5 +12V PB 6 +12V A1 PS_ON A2 +12V RMT SENSE RETURN A3 TEMP_OK A4 PS_SEATED ( Power Supply Seated) A5 +3V3 STAND-BY A6 +3V3SB RETURN B1 DC input OK B2 +12V RMT SENSE B3 +12V CURRENT SHARE B4 PS_INHIBIT/PS_KILL B5 +3V3 STAND-BY B6 +3V3SB RETURN Pin Assignments Pin Signal Name C1 SDA (I2C Data Signal) C2 SCL (I2C Clock Signal)* C3 POWER GOOD C4 FAN FAIL (Fan Fail Signal) C5 +3V3 STAND-BY C6 +3V3SB RETURN D1 A0 (I2C Address BIT 0 Signal) D2 A1 (I2C Address BIT 1 Signal) D3 S_INT (Alarm) D4 +3V3 STAND-BY RMT SENSE D5 +3V3 STAND-BY D6 +3V3SB RETURN *Supports I2C standard mode (100 kHz) only P1 - Power Supply Side FCI Power Blade 51721 series 51721-10002406AA Molex Power Connector SD-87667 series 87667-7002 Mating Connector (System Side) FCI Power Blade 51741-10002406CC Strait Pins FCI Power Blade 51761-10002406AA Right Angle