PI216MC-DR AMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

  • Light source, lens, and sensor are integrated into a single module
  • 8 dpm resolution, 88 mm scanning length
  • Up to 176 µsec/line scanning speed, with 4 MHz pixel rate (See Table 3, Note 3.)
  • Wide dynamic range
  • Two-Level Tracking Digital Output ( “ Dynamic Threshold Digitizer ” )
  • 660 nm light source (other colors available)
  • Compact size ≅ 13 mm x 25.6 mm x 102 mm
  • Low power
  • Light weight General Description The PI216MC-DR is a contact image sensor, CIS, module with a n additional on board circuit that digitizes the analog pixels from the CIS image sensor to a “ background- tracking ” , two-level digital output signal. It is based on CIS modul e, the PI209M-A6 manufactured by PIC, but with a shorter read length of 88 mm . Hence, its performance is equivalent to the PI209M-A6 that uses MOS image sensor technology to gains its high- speed performance and high sensitivity. The PI216MC-DR is su itable for scanning documents with width of 88 mm and with resolution of 8 dots per millimeter. Its has broad applications, but it was especially designed for the followi ng areas:
  • Where data compression is required, such as in data transmis sions.
  • Where component pin-out count must be kept to a minimum. PI216MC-DR Engineering Data Sheet Peripheral Imaging Corporation 200DPI CIS Two Level Digital Output Module PAGE 1 OF 9 - PI216MC-DR, 7/7/99

referred to as the “ tracking digitizer ” . output of the module. See Figure 1, the block diagram of the PI216MC-DR module. source from dust. The pictorial of PI216MC-DR cross section is shown in Figure 2. FIGURE 1. BLOCK DIAGRAM OF

The table of pins and their functions are listed in Table I, Pin Configuration.

1 DIGOUT Digital Video Output

2 Vdd (+5 V) Ground; 0 V

3 Vn (-5 V) Negative power supply

4 SP Start Pulse for the shift register

5 GRD Ground; 0 V

6 CLOCK Clock for the shift register

7 GLED Return for the LED light source

8 VLED Power in for the LED light

Table 1. Pin configuration The connector is a 8-pin 1-mm surface mount flex input, Molex 52207-0890.

  • Clock is on Pin 6 of the I/O Connector. This is main clock i nput into the CIS Module.
  • SP is on Pin 4. This is the start clock input to the CIS Mo dule. PAGE 4 OF 9 - PI216MC-DR, 7/7/99
  • VDD is on Pin 2. This is a + 5 Volts supply.
  • VN is on Pin 3. This is a – 5 Volts supply.
  • VLED is on Pin 8. This is a +5 Volts supply for the LED ligh t source. Note: Power return for the LED light source is GLED on Pin 7 and the ground return for the CIS modules is pin 5. Video Output : DIGOUT is on pin 1 of the I/O connector. This is the digital video output from the CIS module. Reflection off the dark target produces a digital si gnal of “ 0 ” level, while the white reflection off the white target produces a digital level of “ one ” . The amplitudes of the white and dark are listed in the table below: Electro-Optical Characteristics (25 ° C)

Table 2. Electro-optical characteristics at 25 ° C. maximum clock frequency is 4.0 MHz. Table 3. Recommended Operating Conditions (25 ° C)

(1) VLED sources are also available from 5 to 24 Voltages. (2) Clock pulse high is specified at 4.0 MHz at 25% duty. Diagram. The timing parametric values and their symbols are given in the Table 4. Table 4. Switching Parameter and Timing Symbol Definition

Signal delay time tdl 50 ns Signal settling time tsh 120 ns Digital Signal Delay tddl 60 ns Digital Signal Off Delay tdodl 20 ns Table 5 Absolute Maximum Rating: Parameter Symbols Maximum Rating Units Vdd 10 V Idd 100 mA Vn -10 V In 30 mA VLED 5.5 V Power supply voltage ILED 400 mA Input clock pulse (high level) Vih Vdd – 0.5 V Input clock pulse (low level) Vil -0.8 V Table 6 Operating Environment Operating temperature Top 0 to 50 0 C Operating humidity Hop 10 to 85 % Storage temperature Tstg -25 to+75 0 C Storage humidity Hstg 5 to 95 % Setup and Adjustments The Clock Rate and Integration Time: This was factory set to a specific application. See note 1 under Table 2, Electro-optical characteristics at 25 ° C. The clock frequency was set to 2.0 MHz. The total integration time was set to 360 µsec. The Required Power. The required power is slightly greater than the specified va lues in Table 3. Circuit Power: Positive Supply: +5 Volts @ 90 mA Negative Supply: -5 Volts @ 20 mA LED Power: +5 Volts @ 300 mA PAGE 7 OF 9 - PI216MC-DR, 7/7/99