P4C422 PYRAMID | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Document # SRAM101 REV. A Revised October 2005

FEATURES

High Speed (Equal Access and Cycle Times) – 10/12/15/20/25/35 ns (Commercial) – 15/20/25/35 ns (Military) CMOS for Low Power – 495 mW Max. – 10/12/15/20/25 (Commercial) – 495 mW Max. – 15/20/25/35 (Military)

DESCRIPTION

The P4C422 is a 1,024-bit high-speed (10ns) Static RAM with a 256 x 4 organization. The memory requires no clocks or refreshing and has equal access and cycle times. Inputs and outputs are fully TTL compatible. Operation is from a single 5 Volt supply. Easy memory expansion is provided by an active LOW chip select one (CS 1) and active HIGH chip select two (CS2) as well as 3-state outputs. P4C422 HIGH SPEED 256 x 4 STATIC CMOS RAM FUNCTIONAL BLOCK DIAGRAM PIN CONFIGURATIONS In addition to high performance and high density, the device features latch-up protection, single event and upset protection. The P4C422 is offered in several packages: 22-pin 400 mil DIP (plastic and ceramic), 24- pin 300 mil SOIC, 24-pin square LCC and 24-pin CERPACK. Devices are offered in both commercial and military temperature ranges. Single 5V±10% Power Supply Separate I/O Fully TTL Compatible Inputs and Outputs Resistant to single event upset and latchup resulting from advanced process and design improvements Standard 22-pin 400 mil DIP, 24-pin 300 mil SOIC, 24-pin square LCC package and 24-pin CERPACK package SOIC (S4) CERPACK (F3) SIMILAR DIP (P3-1, C3-1, D3-1) LCC (L4)

Page 2 of 10Document # SRAM101 REV. A DC ELECTRICAL CHARACTERISTICS Over recommended operating temperature and supply voltage (2) P4C422 Min Max VOH Output High Voltage I OH = –5.2 mA, VCC = Min.2.4 V VOL Output Low Voltage I OL = +8 mA, VCC = Min. 0.4 V VIH Input High Voltage 2.1 V VIL Input Low Voltage 0.8 V VCL Input Clamp Diode Voltage I IN = –10 mA –1.5 V IIX Input Load Current GND ≤ VIN ≤ VCC –10 10 µA IOZ Output Current (High Z) V OL ≤ VOUT ≤ VOH , Output Disabled –10 10 µA IOS Output Short Circuit V CC= Max., VOUT = GND 90 mA Current(3) Grade(2) Ambient Temp Gnd Vcc Commercial 0°C to 70°C 0V 5.0V ±10% Military – 55°C to 125°C 0V 5.0V ±10% Symbol Parameter Test Conditions Unit Symbol Parameter Conditions Typ. Unit CIN Input Capacitance V IN = 0V 5 pF COUT Output Capacitance VOUT = 0V 7 pF CAPACITANCES(4) (VCC = 5.0V, TA = 25°C, f = 1.0MHz) RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit TBIAS Temperature Under –55 to +125 °C Bias TSTG Storage Temperature –65 to +150 °C IOUT DC Output Current 20 mA MAXIMUM RATINGS(1) Symbol Parameter Value Unit V CC Power Supply Pin with –0.5 to +7 V Respect to GND Terminal Voltage with –0.5 to VTERM Respect to GND V CC +0.5 V (up to 7.0V) TA Operating Temperature –55 to +125 °C Notes: 1. Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to MAXIMUM rating conditions for extended periods may affect reliability. 2. Extended temperature operation guaranteed with 400 linear feet per minute of air flow. 3. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds. 4. This parameter is sampled and not 100% tested. 5. Transition time is ≤ 3ns for 10, 12, and 15 ns products and ≤ 5ns for 20, 25, and 35 ns products, see Fig 1d. Timing is referenced at input and output levels of 1.5V. The output loading is equivalent to the specified I OL/IOH with a load capacitance of 15 pF (10, 12) or 30 pF (15, 20, 25, 35) as in Fig. 1a and 1b respectively. 6. Transition time is ≤ 3ns for 10, 12, and 15 ns products and ≤ 5ns for 20, 25, and 35 ns products, see Fig 1d. Transition is measured at steady state HIGH level -500mV or steady state LOW level +500mV on the output from a level on the input with load shown in Fig. 1c. 7. t W is measured at tWSA = min.; tWSA is measured at tW = min. POWER DISSIPATION CHARACTERISTICS VS. SPEED Symbol ICC Parameter Dynamic Operating Current Temperature Range Commercial Military -10 N/A -12 N/A -15 -20 -25 -35 Unit mA mA

Page 3 of 10Document # SRAM101 REV. A Mode CS 2 CSCSCSCSCS1 WEWEWEWEWE OEOEOEOEOE Output Standby L X X X High Z Standby X H X X High Z DOUT Disabled H L X H High Z Read H L H L D OUT Write H L L X High Z recovery times by eliminating the “write recovery glitch.” Reading is performed with chip selct one (CS1) LOW, chip select two (CS 2) HIGH, write enable ( WE) HIGH and output enable ( OE) LOW. The information stored in the addressed word is read out on the noninverting outputs 0 through O 3). The outputs of the memory go to an inactive high impedance state whenever chip select one (CS 1) is HIGH, or during the write operation when write enable (WE) is LOW. An active LOW write enable ( WE) controls the writing/ reading operation of the memory. When the chip select one (CS 1) and the write enable (WE) are LOW and the chip select two (CS2) is HIGH, the information on data inputs (D0 through D3) is written into the addressed memory word and preconditions the output circuitry so that true data is present at the outputs when the write cycle is complete. This preconditioning operation insures minimum write FUNCTIONAL DESCRIPTION TRUTH TABLE AC ELECTRICAL CHARACTERISTICS—READ CYCLE (VCC = 5V ± 10% except as noted, All Temperature Ranges)(2) TIMING WAVEFORM OF READ CYCLE Notes: H = HIGH L = Low X = Don't Care HIGH Z = Implies outputs are disabled or off. This condition is defined as high impedance state for the P4C422. Sym. tRC tACS tZRCS tAOS tZROS tAA Read Cycle Time (5) Chip Select Time (5) Chip Select to High-Z (6) Output Enable Time Output Enable to High-Z (6) Address Access Time (5) -10* Min Max 7.5 7.5 -12 Min Max -15 Min Max -20 Min Max -25 Min Max -35 Min Max Unit ns ns ns ns ns ns25 *VCC = 5V ± 5% Parameter

Page 4 of 10Document # SRAM101 REV. A Max AC CHARACTERISTICS—WRITE CYCLE (VCC = 5V ± 10% except as noted, All Temperature Ranges)(2) TIMING WAVEFORM OF WRITE CYCLE Parameter Write Cycle Time (5) Write Enable to High-Z (6) Write Recovery Time Write Pulse Width (5,7) Data Setup Time Prior to Write (5) Data Hold Time (5) Address Setup Time (5,7) Address Hold Time (5) Chip Select Setup Time (5) Chip Select Hold Time (5) Sym. tWC tZWS tWR tW tWSD tWHD tWSA tWHA tWSCS tWHCS -10* -12 -15 -20 -25 -35 Unit Min Max Min Max Min Max Min Min Max Min Max ns ns ns ns ns *VCC = 5V ± 5% 225 55 n s 00 0 25 5n s 22 4 55 5 ns 0 002 55n s 22 55 5n s

Page 6 of 10Document # SRAM101 REV. A *Military temperature range with MIL-STD-883, Class B compliance. N/A = Not Available SELECTION GUIDE The P4C422 is available in the following temperature range, speed, and package options.

ORDERING INFORMATION

Plastic DIP -10PC -12PC -15PC -20PC -25PC -35PC SOIC -10SC -12SC -15SC -20SC -25SC -35SC Side Brazed DIP N/A N/A -15CM -20CM -25CM -35CM CERDIP N/A N/A -15DM -20DM -25DM -35DM LCC N/A N/A -15LM -20LM -25LM -35LM CERPACK N/A N/A -15FM -20FM -25FM -35FM Side Brazed DIP N/A N/A -15CMB -20CMB -25CMB -35CMB CERDIP N/A N/A -15DMB -20DMB -25DMB -35DMB LCC N/A N/A -15LMB -20LMB -25LMB -35LMB CERPACK N/A N/A -15FMB -20FMB -25FMB -35FMB Military Temperature Military Processed* Speed (ns )Temperature Range Package Commercial Temperature

Page 7 of 10Document # SRAM101 REV. A SIDE BRAZED DUAL IN-LINE PACKAGE CERDIP DUAL IN-LINE PACKAGE α Pkg # # Pins Symbol Min Max A - 0.200 b 0.014 0.026 b2 0.035 0.060 C 0.008 0.015 D - 1.100 E 0.360 0.410 eA e L 0.125 0.200 Q 0.015 0.060 S1 0.005 - S2 0.005 -

0.100 BSC

22 (400 Mil)

0.400 BSC

Pkg # # Pins Symbol Min Max A - 0.225 b 0.014 0.026 b2 0.045 0.065 C 0.008 0.018 D - 1.111 E 0.350 0.410 eA e L 0.125 0.200 Q 0.015 0.070 S1 0.005 - 0° 15° 22 (400 Mil)

Page 8 of 10Document # SRAM101 REV. A SQUARE LEADLESS CHIP CARRIER CERPACK CERAMIC FLAT PACKAGE Pkg # # Pins Symbol Min Max A 0.060 0.090 b 0.015 0.022 c 0.004 0.009 D- 0 . 6 3 0 E 0.330 0.380 e k 0.008 0.015 L 0.250 0.370 Q 0.026 0.045 S- 0 . 0 8 5 S1 0.005 -

0.050 BSC

Pkg # # Pins Symbol Min Max A 0.060 0.075 A1 0.050 0.065 B1 0.022 0.028 D/E 0.395 0.410 D1/E1 D2/E2 D3/E3 - 0.410 e h j L 0.045 0.055 L1 0.045 0.055 L2 0.075 0.095 ND NE

0.040 REF

0.020 REF

0.250 BSC

0.125 BSC

Page 9 of 10Document # SRAM101 REV. A PLASTIC DUAL IN-LINE PACK- AGE SMALL OUTLINE IC PLASTIC PACKAGE α α Pkg # # Pins Symbol Min Max A - 0.210 A1 0.015 - b 0.014 0.022 b2 0.045 0.065 C 0.009 0.015 D 1.065 1.120 E1 0.330 0.390 E 0.390 0.425 e eB - 0.500 L 0.115 0.160 0° 15° 22 (400 Mil) Pkg # # Pins Symbol Min Max A 0.093 0.104 A1 0.004 0.012 b2 0.013 0.020 C 0.009 0.012 D 0.598 0.614 e E 0.291 0.299 H 0.394 0.419 h 0.010 0.029 L 0.016 0.050 0° 8° 24 (300 Mil)

Page 10 of 10Document # SRAM101 REV. A REVISIONS DOCUMENT NUMBER: SRAM101 DOCUMENT TITLE: P4C422 HIGH SPEED 256 x 4 Static CMOS RAM REV. ISSUE DATE ORIG. OF CHANGE DESCRIPTION OF CHANGE OR 1997 DAB New Data Sheet A Oct-05 JDB Change logo to Pyramid