DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

30 W DC-DC Converter P30J-Series

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

  • Wide 4:1 input range
  • 1600 VDC isolation
  • Soft start up
  • Remote control input
  • Adjustable output voltage
  • Standard package 1” x 1” x 0.4”
  • -40...100 °C operating temperature range
  • Protected against over current, continuous short circuit, and over temperature, over voltage Model guide Type Input voltage Input current Output voltage [VDC] Output current Efficiency typ. [%] Capacitive load max. [µF] note 1 Nominal [VDC] range [VDC] no load [mA] typ. full load [mA] typ. min. [mA] max. [mA] Single output P30J243R3S 24 9...36 10 1100 3.3 0 7000 88 10000 P30J2405S 24 9...36 10 1400 5.0 0 6000 89 7200 P30J2412S 24 9...36 10 1400 12.0 0 2500 89 1200 P30J2415S 24 9...36 10 1400 15.0 0 2000 91 1000 P30J483R3S 48 18...75 8 540 3.3 0 7000 89 10000 P30J4805S 48 18...75 8 700 5.0 0 6000 90 7200 P30J4812S 48 18...75 8 700 12.0 0 2500 90 1200 P30J4815S 48 18...75 8 700 15.0 0 2000 92 1000 Dual output P30J2412D 24 9...36 10 1400 ±12.0 ±0 ±1250 89 2 x 750 P30J2415D 24 9...36 10 1400 ±15.0 ±0 ±1000 91 2 x 500 P30J4812D 48 18...75 8 700 ±12.0 ±0 ±1250 90 2 x 750 P30J4815D 48 18...75 8 700 ±15.0 ±0 ±1000 91 2 x 500 Specifications Page 1 of 4 General Switching frequency 300 kHz, typ. Start up time 30 ms, typ. Reliability Calculated MBTF 370 000 h Safety standards EN-, IEC-, UL-, ULc 60950-1 EN-, IEC-, UL-, ULc 62368-1 EMC Radiated emissions EN 55032 class A Conducted emissions EN 55032 class A ESD IEC61000-4-2 perf. criteria A RS IEC61000-4-3 perf. criteria A EFT (see Fig. 4) IEC61000-4-4 perf. criteria A Surge (see Fig. 4) IEC61000-4-5 perf. criteria A CS IEC61000-4-6 perf. criteria A PFMF IEC61000-4-8 perf. criteria A Environmental Operating ambient temperature -40 ... 100 °C (see derating diagram) Case temperature 105 °C, max. Over temperature protection, automatic restart 115 °C, typ., case surface Storage temperature -55 .. 125 °C Storage humidity 95 %, max, non condensing Cooling by free air convection > 16 … 33 cm/s Physical Dimensions standard version 25.4 x 25.4 x 10.9 mm Dimensions with heat sink 25.4 x 25.4 x 17.2 mm Weight standard version 19 g Weight with heat sink 21 g Thermal impedance 13 K / W, standard version

12 K / W, with heat sink

Potting Material Epoxy UL94V-0 rated Absolute maximum ratings P30J24xxS, P30J24xxD 50 VDC max. for 0.1 s max. P30J48xxS, P30J48xxD 100 VDC max. for 0.1 s max. Pin soldering temperature distance 1.5 mm from body 260 °C for 10 s Input Start up voltage P24Jxxx: 8.6 V P48Jxxx: 17.5 V Under voltage lockout P24Jxxx: 7.6 V P48Jxxx: 16.5 V Filter π − type Input ripple current 30 mAp-p (see Fig. 1) Remote control input Pin 3 On state 3 … 12 V (see Fig. 3) Off state 0 … 1.2 V (see Fig. 3) Idle current @ Off state 2 mA, typ. Isolation: Rated voltage, input to output 1600 VDC, 60s Rated voltage, input or output to case

1600 VDC

Resistance 109 Ω Capacitance 2000 pF, typ. Output Voltage accuracy ± 1 % Voltage trim range, only single ± 10 %, max. Dual output cross regulation ± 5 % @ 75 % load difference Line voltage regulation ± 0.5 % Load regulation, single output ± 0.5 % @ 0 %...100 % load Load regulation, dual output, at balanced load current Ripple and noise (20 MHz BW) 75 mVp-p (see Fig. 2) Short circuit protection Indefinite, automatic restart Over load protection 170 %, typ. Temperature coefficient ± 0.02 % / °C Transient recovery time 250 µs, typ., @ 25 % load steps Transient response deviation ± 5 %, max. Output over voltage protection P30Jxx3R3x 3.9 V Z-Diode P30Jxx05x 6.2 V Z-Diode P30Jxx12x 15 V Z-Diode P30Jxx15x 18 V Z-Diode

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Fig. 1 Input reflected ripple current measure circuit Input reflected current is measured through a source inductor and a source capacitor at nominal input voltage and full load. Fig. 2 Output ripple & noise measurement test method Use the following measurement circuit. The oscilloscope mesurement bandwidth must be > 20 MHz. Fig. 3 ON / OFF remote control circuit ON / OFF remote control circuit for inverse logic Page 2 of 4 RL +Vin -Vout +Vout DC DC 10 µF MLCC GND CH1 -Vin/GND 47 µF + +Vin Load -Vout -Vin/GND +Vout 12 µH Measure point DC DC ESR <1 Ω @ 100 kHz 10 µF MLCC 10 µF MLCC RL RL +Vin -Vout -Vin/GND +Vout DC DC CH1 CH2 COM +Vin -Vin/GND Ctrl +Vin Load -Vout +Vout DC DC Remote control input on: 3 V…≤12 V or open off: 0…1.2 V -Vin/GND +Vin -Vin/GND Load -Vout +Vout DC DC off Remote control input on on off

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Fig. 4 External circuits to meet EMI standards IEC61000-4-4 and IEC61000-4-5 BOM to Fig. 4 Type C1 D C2 D P30J24xxx 3.3 µF, 100 V 0.82 µH 330 µF, 100 V TVS Diode 58 V, 3 kW P30J48xxx 1 µF, 100 V 2.2 µH 330 µF, 100 V TVS Diode 120 V, 3 kW Fig. 5 Trim down application circuit with fixed resistors Trim trim up application circuit with fixed resistors Trim application circuit with potentiometer Page 3 of 4 +Vin -Vin Load 4 -Vout 6 +Vout DC DC

5 Trim

+Vin -Vin Load 4 -Vout 6 +Vout DC DC +Vin -Vin 4 -Vout 6 +Vout DC DC Load +Vin -Vin/GND D +Vin Load -Vout -Vin +Vout DC DC cer. L EFT & Surge- Filter EMI-Filter to meet class A

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Dimensions standard version Notes: Dimensions in mm Pin diameter tolerance ± 0.05 mm Pin pitch tolerance ± 0.35 mm Case tolerance ± 0.5 mm Stand off tolerance ± 0.1 mm Dimensions heatsink version Notes: Dimensions in mm Pin diameter tolerance ± 0.05 mm Pin pitch tolerance ± 0.35 mm Case tolerance ± 0.5 mm Stand off tolerance ± 0.1 mm Page 4 of 4 Pin assignment Pin Single output Dual output 1 +V input +V input 2 -V input -V input 3 Rem. control Rem. control 4 -V output -V output

5 Trim Common

PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals ! Not for resale or distribution to the general public in any way ! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for us e in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 20170828 f