DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

12 W DC-DC Converter P12C-Series

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

  • 2:1 Wide Input Range
  • 1600 VDC Isolation
  • MTBF >1 Mio. h
  • Continuous Short Circuit Protection
  • Efficiency up to 91%
  • Soft Start
  • On/Off remote Control
  • Wide Operation Temperature Range -40...85°C Model guide Type Input voltage Input current Output voltage [VDC] Output current [mA] Efficiency typ. [%] Capacitor load [µF] max. Nominal [VDC] Range [VDC] No load [mA] Full load [mA] Single output P12C122R5S 12 9...18 15 890 2.5 0…3500 85 2000 P12C123R3S 12 9...18 15 1145 3.3 0…3500 87 2000 P12C1205S 12 9...18 15 1165 5.0 0…2400 89 2000 P12C1212S 12 9...18 15 1150 12.0 0…1000 90 430 P12C1215S 12 9...18 15 1150 15.0 0…800 90 300 P12C242R5S 24 18...36 15 445 2.5 0…3500 85 2000 P12C243R3S 24 18...36 15 575 3.3 0…3500 87 2000 P12C2405S 24 18...36 15 580 5.0 0…2400 89 2000 P12C2412S 24 18...36 15 575 12.0 0…1000 90 430 P12C2415S 24 18...36 15 575 15.0 0…800 90 300 P12C482R5S 48 36...75 15 225 2.5 0…3500 84 2000 P12C483R3S 48 36...75 15 285 3.3 0…3500 88 2000 P12C4805S 48 36...75 15 290 5.0 0…2400 89 2000 P12C4812S 48 36...75 15 295 12.0 0…1000 88 430 P12C4815S 48 36...75 15 290 15.0 0…800 89 300 Dual output P12C1212D 12 9...18 15 1150 ±12.0 ± 0…500 90 2 x 200 P12C1215D 12 9...18 15 1135 ±15.0 ± 0…400 91 2 x 120 P12C2412D 24 18...36 15 575 ±12.0 ± 0…500 90 2 x 200 P12C2415D 24 18...36 15 560 ±15.0 ± 0…400 91 2 x 120 P12C4812D 48 36...75 15 295 ±12.0 ± 0…500 88 2 x 200 P12C4815D 48 36...75 15 290 ±15.0 ± 0…400 89 2 x 120 Specifications Page 1 of 4 General Switching frequency 330 kHz, typ. Safety Standard IEC 60950-1 Reliability calculated MTBF (MIL-HDBK-217F) > 1 Mio. h EMC Characteristics Radiated Emissions (See figure 3) EN55032 class A Conducted Emissions (See figure 3) EN55032 class A ESD EN61000-4-2 Crit. B RS EN61000-4-3 Crit. A EFT EN61000-4-4 Crit. A Surge (See figure 3) EN61000-4-5 Crit. A CS (See figure 3) EN61000-4-6 Crit. A PFMF EN61000-4-8 Crit. A Environmental Operating ambient temperature -40 … 85 °C (see derating) Storage temperature -40 … 125 °C Case temperature 100 °C max. Derating see diagram Storage humidity Up to 95 %, non condensing Cooling Free air convection 16...33 cm/s Physical Dimensions 31.75 x 20.32 x 10.16 mm Weight 18 g Case material Nickel coated copper Potting material Epoxy (UL94V-0 rated) Absolute maximum conditions Soldering temperature < 260 °C for <10 s, > 1.5 mm distance from body Input surge voltage for < 1 s P12C12xxx: 36 VDC, max. P12C24xxx: 50 VDC, max. P12C48xxx: 100 VDC, max. Input Filter Pi Network Reflected input current 20 mAp-p (see figure 1) Start up time with R-load 20 ms typ. Remote CTRL on/off, Pin1 (See figure 4) On: 3...12 V or open input Off: 0...1.2 V Standby idle current 5 mA typ. Isolation: Rated voltage (for 60 s) Input to output: 1600 VDC Case to input/output: 1600 VDC Resistance 109 Ω Capacitance 1200 pF, typ. Output Voltage accuracy ± 1.2 %, max. Line regulation ± 0.5 %, max. P30CxxxxD: ± 1 %, max. Cross regulation ± 5 % Ripple and noise (at 20 MHz BW) 85 mVp-p, max. (See figure 2) Over current limiting 150 % of Iout max. Temperature coefficient ± 0.02 % / °C Short circuit protection Indefinite, hiccup, automatic restart Transient recovery time @ 25 % load change steps 250 µs typ. Transient response drift @ 25 % load change steps 3 %, max. Over voltage protection P12Cxx2V5S, P12Cxx3R3S 3.9 V Z-diode clamping P12Cxx05S 6.2 V Z-diode clamping P12Cxx12x 15 V Z-diode clamping P12Cxx15x 18 V Z-diode clamping

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Notes: 1. All parameter are typical specified at 25 °C ambient temperature, nominal input voltage and full load, unless otherwise noted. 2. Capacitive load tested by minimal input voltage and constant resistive load. 3. An external filter is required to meet EFT standard IEC 61000-4-4 and IEC 61000-4-5. (see Figue 3) Figure 1 Measure circuit for reflected input ripple current Figure 2 Measure circuit for output ripple and noise voltage Figure 3 Input filter circuit to meet the class A specifications The filter components should be mounted as near as possible and with shortest connections to the DC/DC-Converter. Figure 4 Remote control circuit for control voltage ≤ 12 V DC Page 2 of 4 47 µF + +Vin Load -Vout -Vin +Vout 12 µH Measure point DC DC ESR <1 Ω @ 100 kHz +Vin -Vin 22, 23 Load -Vout 2, 3 +Vout DC DC Remote control input on: 3…≤12 V or open Input off: 0…1.2 V RL 1 µF Cer. +Vin -Vout +Vout DC DC GND CH1 -Vin/GND + 330 µF Type KY Nippon Chemicon +Vin Load -Vout -Vin +Vout 12 µH DC DC

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Page 3 of 4

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Dimensions Page 4 of 4 Pin assignment Pin Single output Dual output 1 Remote contr. Remote contr. 2 -V Input -V Input 3 -V Input -V Input

9 Omitted Common

11 N.C. -V Output 14 +V Output +V Output 16 -V Output Common 22 +V Input +V Input 23 +V Input +V Input PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals ! Not for resale or distribution to the general public in any way ! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devic es which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 20180611 f Note: All dimensions in mm Pin diameter tolerance: ± 0.05 mm Pin pitch and length tolerance: ± 0.35 mm Case tolerance: ± 0.5 mm Stand-off tolerance: ± 0.1 mm