DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

30 W DC-DC Converter P30HxxxxCx-Series

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

  • Wide 4:1 input range
  • Efficiency up to 90 %
  • Adjustable output voltage
  • Remote control on / off
  • 1500 VDC isolation
  • Continuous short circuit protection
  • Over voltage protection
  • -40...+80 °C operating temperature range Model guide Specifications Page 1 of 8 Type Input voltage Input current Output voltage [VDC] Output current Efficiency @ full load [%] typ. Capacitive load (see note 1) [µF] max. Nominal [VDC] Range [VDC] no load [mA] typ. full load [mA] typ. minimum load [mA] typ. maximum load [mA] typ. Single output P30H243R3CS 24 9...36 60 1000 3.3 0 6000 85 10000 P30H2405CS 24 9...36 60 1400 5 0 6000 88 10000 P30H2409CS 24 9...36 6 1400 9 0 3333 88 4700 P30H2412CS 24 9...36 6 1400 12 0 2500 90 2700 P30H2415CS 24 9...36 6 1400 15 0 2000 90 1680 P30H2424CS 24 9...36 6 1400 24 0 1250 90 680 P30H483R3CS 48 18...75 20 500 3.3 0 6000 86 10000 P30H4805CS 48 18...75 20 700 5 0 6000 88 10000 P30H4812CS 48 18...75 5 700 12 0 2500 88 2700 P30H4815CS 48 18...75 5 700 15 0 2000 89 1680 P30H4824CS 48 18...75 5 700 24 0 1250 89 680 Dual output P30H2405CD 24 9...36 60 1400 ±5 0 ±3000 86 2 x 2000 P30H2412CD 24 9...36 6 1400 ±12 0 ±1250 89 2 x 1250 P30H2415CD 24 9...36 6 1400 ±15 0 ±1000 89 2 x 680 P30H2424CD 24 9...36 6 1400 ±24 0 ±625 89 2 x 470 P30H4805CD 48 18...75 20 700 ±5 0 ±3000 86 2 x 2000 P30H4812CD 48 18...75 5 700 ±12 0 ±1250 88 2 x 1250 P30H4815CD 48 18...75 5 700 ±15 0 ±1000 88 2 x 680 Input Under voltage lockout P30H24xxCS: 5.5 VDC P30H48xxCS: 12 VDC Start up voltage P30H24xxCS: 9 VDC P30H48xxCS: 18 VDC Filter π - type Reflected ripple current 40 mAp-p, typ. (see Figure 1) Remote control theshold On: 3.5…12 VDC, or open input Off: 0…1.2 VDC Off state idle supply current 8 mA, max. Rated isolation voltage Input / output (1 Min. tested) 1500 VDC, min. Resistance > 109 Ω, measured @ 500 VDC Input / output capacitance 2000 pF, typ. @ 100 kHz, 0.1V Output Voltage tolerance ± 1 %, typ. @ full load range ± 3 %, max. @ 5…100 % l oad ± 5 %, max. @ 0… 5 % load Line regulation, positive output ± 0.5 %, max @ full Vin range Line regulation, negative output ± 1 %, max @ full Vin range Load regulation, positive output ± 1 %, max. @ 5..100 % load Load regulation, negative output ± 1.5 %, max. @ 5..100 % load Dual output cross regulation ± 5 %, max. @ 50 % load +Vout and 10…100 % load -Vout Temperature coefficient ± 0.03 % / °C Transient recovery time < 500 µs, @ 25 % load change steps Transient response deviation P30Hxx3R3CS, P30Hxx05Cx < 8 %, @ 25 % load change steps Oll others < 5 %, @ 25 % load change steps Short circuit protection Continuous, hiccup Short circuit restart Automatic Output voltage trim range ± 10 % Rippel & noise, BW 20MHz (see Figure 2) Single output: 100 mVp-p, max. Dual output: 150 mVp-p, max. Over current protection 110… 190 % of full load Over voltage protection 110… 160 % of nominal Vout General Start up time 10 ms, typ @ constant R-load Switching frequency 300 kHz, typ. Reliability calculated MTBF MIL-HDBK-217F @ 25 °C > 1 Mio. hours EMC characteristics Radiated emissions CISPR32 / EN55032 Class A Radiated emissions, see Fig. 2 CISPR32 / EN55032 Class B Conducted emissions CISPR32 / EN55032 Class A Conducted emissions, see Fig. 2 CISPR32 / EN55032 Class B ESD, contact ± 4kV EN61000-4-2 perf. crit. B see Fig. 2 RS 10 V/m EN61000-4-3 perf. crit. A EFT ±2 kV EN61000-4-4 perf. crit. B see Fig. 2 Surge ±2 kV EN61000-4-5 perf. crit. B see Fig. 2 CS 3 Vrms EN61000-4-6 perf. crit. A Environmental Operating ambient temperature -40 … 80 °C with derating Case temperature 105 °C, max. Storage temperature -55 … 125 °C Storage humidity 5…95 %, non condensing Cooling Free air convection Vibration 10…55 Hz,10 g, 30 Min. along X, Y, Z axis Physical Dimensions without heatsink with heatsink 50.8 x 25.4 x 11.8 mm 51.4 x 26.2 x 16.5 mm Weight without heatsink with heatsink 26 g 34 g Case material Aluminium alloy Potting Material Epoxy (UL94V-0 rated) Absolute max. ratings Pin soldering temperature ≤ 300 °C for ≤ 10 sec ≥ 1.5 mm distance from body Max. input voltage < 1 s P30H24xxCx: -0.7…50 VDC P30H48xxCx: -0.7…100 VDC

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Odering information Output power Series designation Input voltage range Output voltage Revision Output configuration Case option P PHI-CON 30 30 W H 24 9…36 V 3R3 3.3 V C S single output blank standard 48 36…75 V 05 5 V D ± dual output K heatsink 12 12 V 15 15 V Notes: 1. Maximum capacitive load is tested at input voltage range and full load. 2. All specifications measured at Ta 25 °C, humidity < 75 %, nominal input voltage and rated output load unless otherwise specified. 3. Specifications of this product are subject to changes without prior notice. 4. It is not recommended to increase the output power capability by connecting two or more converters in parallel. 5. The converters are not hot swappable. Figure 1 Input reflected ripple current measure circuit The input reflected ripple current is measured with inductor Lin and capacitor Cin to simulate source impedance. Figure 2a Output ripple & noise parallel strip line measurement method Single output Page 2 of 8 1 µF 10 µF + RL +Vin +Vout DC DC GND 25.4 12.7 50.8 Dimensions in mm Copper Foil 2.54 MLCC RF-Probe head +Vin Load GND +Vout 4.7 µH DC DC Measure point 220 µF + ESR <1 Ω @ 100 kHz

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Figure 2b Output ripple & noise parallel strip line measurement method Dual output Figures 3 Typical application circuits The P30HxxxxCx series is been tested according to the following recommended test circuit before leaving the factory (see Figures 3). If you want to further decrease the input / output ripple, you can increase a capacitance values properly or choose capacitor s with low ESR, but the total capacitance of the filter capacitor must not exceed the maximum load capacitance value. (see „Model guide“ table right column) Page 3 of 8 Recommended peripheral components to figure 3 Type Cout Cin P30Hxx3R3CS 220 µF 100 µF P30Hxx05CS 220 µF P30Hxx09CS 220 µF P30Hxx12CS 100 µF P30Hxx15CS 100 µF P30Hxx24CS 100 µF P30Hxx05CD 2 x 220 µF P30Hxx12CD 2 x 220 µF P30Hxx15CD 2 x 220 µF P30Hxx24CD 2 x 100 µF +Vin GND 0 V +Vout DC DC Cout Cin Load Load +Vin GND -Vout +Vout DC DC Cout Cout Cin 0 V Load MLCC MLCC -Vout 1 µF 10 µF + RL 1 µF 10 µF + RL DC DC GND +Vin +Vout 25.4 12.7 50.8 Dimensions in mm 2.54 2.54 Copper Foil RF-Probe head RF-Probe head

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Recommended EMC circuit for higher performance of class B Figure 4a single output Figure 4b dual output Page 4 of 8 Recommended peripheral components to circuits in figure 4a, single output version Type Fuse time delayed type MOV Type Cin C2 CX LCM CY Cout P30H243R3CS 5 A S20K30 680 µF, 50 V 4.7 µF, 50 V 330 µF, 50V 1 mH 1 nF, 2 kV 220 µF P30H2405CS P30H2409CS P30H2412CS 5 A S20K30 680 µF, 50 V 4.7 µF, 50 V 330 µF, 50V 1 mH 1 nF, 2 kV 100 µF P30H2415CS P30H2424CS P30H483R3CS 2.5 A S14K60 330 µF, 100 V 2.2 µF, 100 V 330 µF, 100 V 1 mH 1 nF, 2 kV 220 µF P30H4805CS P30H4809CS P30H4812CS 2.5 A S14K60 330 µF, 100 V 2.2 µF, 100 V 330 µF, 100 V 1 mH 1 nF, 2 kV 100 µF P30H4815CS P30H4824CS Recommended peripheral components to circuits in figure 4b, dual output version Type Fuse time delayed type MOV Type Cin C1 C2 CX L CY Cout P30H2405CD 5 A S20K30 680 µF, 50 V 2.2 µF, 50 V 4.7 µF, 50 V 330 µF, 50V 3.3 µH 1 nF, 2 kV 220 µF P30H2412CD P30H2415CD P30H2424CD 5 A S20K30 680 µF, 50 V 2.2 µF, 50 V 4.7 µF, 50 V 330 µF, 50V 3.3 µH 1 nF, 2 kV 100 µF P30H4805CD 2.5 A S14K60 330 µF, 100 V 2.2 µF, 100 V 2.2 µF, 100 V 330 µF, 100 V 3.3 µH 1 nF, 2 kV 220 µF P30H4812CD P30H4815CD +Vin GND Load +Vout DC DC LCM EMI-Filter to meet class B EFT & Surge Filter to meet class B MOV CX Fuse CY CY Cout Cin +Vin GND Load -Vout +Vout DC DC L EMI-Filter to meet class B EFT & Surge Filter to meet class B MOV CX Fuse CY CY Cout Load Cout Cin

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Figure 5 Application circuit remote control Figure 6 Application circuit to output voltage trimming Calculation for trim down resistor (Rtd) or trim up resistor (Rtu) Model series R1 [kΩ] R2 [kΩ] R3 [kΩ] V Ref [V] Rtd min. [kΩ] Rtu min. [kΩ] P30Hxx3R3CS 4.801 2.87 12.4 1.24 11.75 6.43 P30Hxx05CS 2.883 10 2.5 1.27 4.75 P30Hxx09CS 7.5 15 30 6.63 P30Hxx12CS 11 15 56 9.6 P30Hxx15CS 14.494 15 83 11.4 P30Hxx24CS 24.872 17.8 167.5 10 Maximum output voltage adjust range ± 10 % of Vout nominal, see min. Rtd / Rtu Trim down resistor formula Trim up resistor formula Page 5 of 8 Rtu= R2*a R2-a -R3 Vref Vout-Vref *R1 Rtd= R1*b R1-b -R3 Vref Vout-Vref *R2 Rtd Trim down circuit P30HxxxxCS 0 V VRef +Vout Rtu Trim up circuit P30HxxxxCS 0 V VRef +Vout +Vin GND Ctrl +Vin Load +Vout DC DC Remote control input on: 3.5 V…≤12 V or open input off: 0…1.2 V GND

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Page 6 of 8

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Page 7 of 8

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Dimensions standard version Footprint top view Dimensions heatsink version Page 8 of 8 Pin assignment single dual 1 + Vin + Vin

2 GND GND

3 CTRL CTRL

4 Trim - Vo

PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals ! Not for resale or distribution to the general public in any way ! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or s ystems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 20180615 f Unit: mm Pin diameter tolerance:± 0.1 mm Pin height tolerance:± 0.5 mm General tolerances:± 0.3 mm