DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

25 W DC-DC Converter P25E-Series

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

  • Very wide input range 10:1
  • 3000 VDC isolation
  • Aluminium heat sink case
  • Continuous short circuit protection
  • Over current protection
  • Over continuous short circuit protection
  • Output over voltage protection
  • Over temperature protection
  • Wide operation temperature range -40...100 °C
  • Adjustable output voltage
  • On / Off remote control input
  • EN 50155 standard Model guide Type Input voltage Input current Output voltage [VDC] Output current Efficiency [%] typ. Capacitor load (note2) [µF] max. Nominal [VDC] Range [VDC] no load [mA] typ. full load [mA] typ. [mA] min. [mA] max. P25E7205SK 72 16...160 10 410 5.0 0 5000 85 6800 P25E7212SK 72 16...160 10 415 12.0 0 2080 84 1000 P25E7215SK 72 16...160 10 410 15.0 0 1670 85 820 P25E7224SK 72 16...160 10 410 24.0 0 1040 85 470 Specifications Notes: 1. All parameter are typical at 25 °C, nominal input voltage and full load specified, unless otherwise noted. 2. Capacitive load tested by minimal input voltage and constant resistive load. Page 1 of 4 EMC Characteristics Radiated Emissions, EN50121-3-2 40 dBµV at 20…230 MHz 47 dBµV at 230 MHz…1 GHz Conducted Emissions EN 50121-3-2 (see figure 3) 99 dBµV at 150…500 kHz 93 dBµV at 500 kHz…30 MHz ESD, EN 50121-3-2, perf. crit. A Air ± 8 kV Contact ± 6 kV RS, EN 50121-3-2 perf. crit. A

20 V/m

EFT, EN 50121-3-2, perf. crit. A (see figure 3) 2 kV Surge, EN 50121-3-2, perf. crit. A (see figure 3) 2 kV CS, EN 50121-3-2 perf. crit. A 10 V PFMF, EN 61000-4-8 perf. crit. A

100 A/m

Operating ambient temperature (see derating diagram) -40… 58 °C, without derating -40… 100 °C, with derating Storage temperature -55…125 °C Case temperature 105 °C, max. Over temperature protection 115 °C surface, typ. Thermal resistance mounted on FR4 PCB 150 mm x 70 mm 8 K/W, typ. Humidity 95 %, max. non condensing Thermal shock IEC 60068 Mechnical shock and vibration EN 61373 Free air convection cooling 30…65 LFM (15...35 cm/s) Physical Dimensions 53 x 27.6 x 16.6 mm Weight 48 g Case material Aluminium Potting material Epoxy (UL94V-0 rated) Absolute maximum ratings Input voltage P25E72xxSK 176 VDC, 100 ms, max. Pin soldering temperature ≤ 260 °C, ≤ 10 s, ≥ 1.5 mm distance from body Input Start up voltage P25E72xxSK: 13.8 VDC Under voltage lockout P25E72xxSK: 12 VDC Filter Pi Network Start up time with R-load 60 ms, typ. Reflected ripple current 20 mAp-p, (see figure 1) ON / OFF Control threshold (see figures 6) On: 3...12 VDC or open input Off: 0...1.2 VDC Standby idle current 3 mA, typ. Isolation: Input / output voltage for 60 s Input or output to case for 60 s

3000 VDC

1600 VDC

Resistance 109 Ω Capacitance 2000 pF, typ. Output Voltage accuracy ± 1 %, max. Voltage trim range (see fig. 5) ± 10 % Over voltage protection via Z-Diode clamping P25E7205S: 6.2 V P25E7212S: 15 V P25E7215S:18 V P25E7224S: 30 V Line voltage regulation ± 0.2 %, max. Load regulation 0...100 % load ± 0.5 %, max. Transient recovery time 500 µs, typ. Transient response deviation @ 25 % load change steps ± 4 %, max. Temperature coefficient ± 0.02 % / °C Ripple and noise (at 20 MHz BW) ≤ 100 mVp-p, (see figure 2) Short circuit protection Indefinite (hiccup), automatic restart Over current protection 150 % of Iout, typ. General Switching frequency 250 kHz, typ. Safety Standard EN 50155 EN-, IEC-, UL 60950-1, EN-, IEC-, UL 62368-1, Reliability calculated MTBF MIL-HDBK-217F at 25 °C 230.000 h

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Figure 1 Measure circuit reflected input ripple current Figure 2 Measure circuit for output ripple & noise voltage, measure band wide 20 MHz Figure 3 Application circuit to meet EN 50121-3-2 and ripple & noise reduction Page 2 of 4 To meet the specified ripple and noise level are for the output filter circuit multilayer ceramic capacitors necessary. 10 µF + +Vin Load -Vout -Vin/GND +Vout 22 µH Measure point DC DC 10 µF + RL +Vin -Vout +Vout DC DC 10 µF MLCC GND CH1 -Vin/GND +Vin - Vin -Vout +Vout Load DC DC 22 µH 10 µF + 10 µF + 1 µF Cer. + 10 µF EFT & Surge- Filter EMI-Filter 2*100 µF BXF / 250 V Rubicon

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Figure 4 Output voltage trimming application Figures 5 ON/OFF remote control application circuit ON/OFF remote control application circuit for inverse logic and higher input level possibility Page 3 of 4 +Vin -Vin/GND Ctrl 3 Load -Vout +Vout DC DC Remote control input on: 3 V…≤12 V or open off: 0…1.2 V +Vin -Vin/GND Ctrl.3 Load -Vout +Vout DC DC Remote control input off on on off -Vin/GND Load 5 -Vout 4 +Vout DC DC

6 Trim

-Vin +Vin

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Dimensions Page 4 of 4 Pin assignment Pin Single out 1 +Vin 2 -Vin 3 Rem. Ctrl. 4 +Vout 5 -Vout PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instruc tions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to p erform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significa nt injury to the user. Rev: 20180905 f Note: All dimensions in mm 1. Pin diameter tolerance ±0.05 mm 2. Pin pitch and lengh tolerance ±0.35 mm 3. Pin to case tolerance ±0.5 mm 4. Case tolerance ±0.5 mm 5. Stand off tolerance ±0.1 mm 6. Recommented Pin hole diameter 1.5 mm