DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

20 W DC-DC Converter P20HxxxxCx-Series

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

  • Wide 4:1 input range
  • Efficiency up to 90 %
  • Adjustable output voltage
  • Remote control on / off
  • 1500 VDC isolation
  • Continuous short circuit protection
  • Over voltage protection
  • Standard package 2” x 1” x 0.4” Model guide With suffix “K” heatsink version Specifications Page 1 of 6 Type Input voltage Input current Output voltage [VDC] Output current Efficiency @ full load [%] typ. Capacitive load (see note 2) [µF] max. Nominal [VDC] Range [VDC] no load [mA] full load [mA] Min. [mA] Max. [mA] P20H243R3CS 24 9...36 40 800 3.3 0 5000 86 10000 P20H2405CS 24 9...36 60 916 5 0 4000 90 10000 P20H2409CS 24 9...36 18 947 9 0 2222 88 4700 P20H2412CS 24 9...36 15 937 12 0 1667 89 1600 P20H2415CS 24 9...36 15 926 15 0 1333 90 1000 P20H2424CS 24 9...36 20 927 24 0 834 90 500 P20H483R3CS 48 18...75 35 400 3.3 0 5000 86 10000 P20H4805CS 48 18...75 35 463 5 0 4000 90 10000 P20H4812CS 48 18...75 10 468 12 0 1667 89 1600 P20H4815CS 48 18...75 10 463 15 0 1333 90 1000 P20H4824CS 48 18...75 10 463 24 0 834 90 500 P20H2405CD 24 9...36 20 969 ±5 0 ±2000 86 2 x 4800 P20H2409CD 24 9...36 20 969 ±9 0 ±1111 88 2 x 1000 P20H2412CD 24 9...36 15 948 ±12 0 ±834 88 2 x 800 P20H2415CD 24 9...36 15 947 ±15 0 ±667 88 2 x 625 P20H4805CD 48 18...75 18 485 ±5 0 ±2000 86 2 x 4800 P20H4812CD 48 18...75 14 474 ±12 0 ±834 88 2 x 800 P20H4815CD 48 18...75 14 468 ±15 0 ±667 89 2 x 625 Input Start up voltage P20H24xxCx: ≤9 VDC P20H48xxCx: ≤18 VDC Under voltage lockout P20H24xxCx: ≥5.5 VDC P20H48xxCx: ≥14 VDC Filter π – type Reflected ripple current 30 mAp-p, typ. (see figure 2) Remote control theshold On state 3.5…12 VDC, or open input Off state 0…1.2 VDC Input idle current @ Off state 4 mA, typ., <7 mA Isolation input - output: Rated voltage (tested 60 s @ ≤1 mA leakage current) 1500 VDC Resistance > 109 Ω, measured @ 500 VDC Input / output capacitance All others 1000 pF, typ. @ 100 kHz, 0.1 V P20C2424CS 2000 pF, typ. @ 100 kHz, 0.1 V Output Output voltage tolerance ≤ ±3 % @ 0…100 % load range Output voltage load regulation ≤ ±1 % deviation, 5… 100 % load Output voltage trim range ± 10 %, typ. Dual output voltage cross balance ≤ ±5 %, @ 90 % load difference Output voltage Vin regulation ≤ ±1 % deviation @ full Vin range Temperature coefficient ± 0.03 % / °C Transient recovery time ≤ 500 µs, @ 25 % load change steps Transient response deviation @ 25 % load change steps P20Hxx3R3Cx, P20Hxx05Cx: <8 % All others: <5 % Over voltage protection via integrated Z-Diode 110…160 % Over current protection 110…190 % Short circuit protection Continuous, hiccup Short circuit restart Automatic Rippel & noise, BW 20 MHz ≤100 mVp-p @ 5..100 % load range (see fig. 3) Start up time 10 ms, typ @ R-load General Safety standard IEC-, UL-, EN60950-1 Switching frequency (PWM) 270 kHz, typ. Reliability calculated MTBF MIL-HDBK-217F @ 25 °C > 1 Mio. h Vibration along X, Y and Z axis 10..55 Hz, 10 g, 30 minutes EMC characteristics Radiated emissions (see fig. 1) CISPR22 / EN55022 Class A Conducted emissions (see fig.1) CISPR22 / EN55022 Class A Radiated emissions (see fig. 4) CISPR22 / EN55022 Class B Conducted emissions, (see fig. 4) CISPR22 / EN55022 Class B ESD, contact ±4 kV (see fig. 4) IEC-, EN61000-4-2 perf. crit. B RS, 10 V/m IEC-, EN61000-4-3 perf. crit. A EFT, ±2 kV, (see fig. 4) IEC-, EN61000-4-4 perf. crit. B Surge, line to line ±2 kV (see fig. 4) IEC-, EN61000-4-5 perf. crit. B Conducted surge 3 Vrms IEC-, EN61000-4-6 perf. crit. A Voltage dips, short interruptions and voltage variations immunity, 0…70 % IEC-, EN61000-4-29 perf. crit. B Environmental Operating ambient temperature -40 … 85 °C with derating Case temperature 105 °C, max. Storage temperature -55 … 125 °C Over temp. protection Case temp. 110 °C, typ Storage humidity 5…95 %, non condensing Cooling Free air convection Physical Dimensions without heatsink with heatsink 50.80 x 25.40 x 11.8 mm 50.80 x 25.40 x 16.3 mm Weight without heatsink with heatsink 26 g 34 g Case material Aluminium alloy Potting Material Epoxy (UL94V-0 rated) Absolute max. ratings Pin soldering temperature ≤300 °C for ≤10 sec, ≥ 1.5 mm distance from body Max. input voltage < 1 sec P20H24xxCx -0.7…50 VDC P20H48xxCx -0.7…100 VDC

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch - Input + Input DC DC + Vin - Vin + Vout - Vout Cout Cin - Input + Input DC DC + Vin - Vin + Vout - Vout Cout Cout Cin Note: 1. The recommended unbalanced load of dual output converter should be low than 5 %. If the load asymmetry greater than 5 %, it may not be guaranteed to meet all specifications listed. Please contact our technical support for more details. 2. Maximum capacitive load is tested at full input voltage range and full load current. 3. All specifications measured at Ta 25 °C, humidity < 75 %, nominal input voltage and rated output load current unless otherwise specified. 4. Specifications of this product are subject to changes without prior notice. 5. It is not recommended to increase the output power capability by connecting two or more converters in parallel. 6. The converters are not hot swappable 1) Recommended circuit The P20H series is been tested according to the following recommended test circuit before leaving the factory (see Figures 1). If you want to further decrease the input / output ripple, you can increase a capacitance values properly or choose capacitors with low ESR, but the total capacitance of the filter capacitor must not exceed the maximum load capacitance value (see „Model guide“ table). Figure 1a Figure 1b Figure 2 Measure circuit input reflected ripple current The input reflected ripple current is measured with inductor Lin and capacitor Cin to simulate source impedance. Page 2 of 6 Recommended peripheral components to figure 1a Cin Cout P20Hxx3R3CS 100 µF 470 µF P20Hxx05CS 470 µF P20Hxx09CS 220 µF P20Hxx12CS 220 µF P20Hxx15CS 220 µF P20Hxx24CS 100 µF Recommended peripheral components to figure 1b Cin Cout P20Hxx05CD 100 µF 220 µF P20Hxx09CD 100 µF P20Hxx12CD P20Hxx15CD + 220 µF +Vin Load -Vout -Vin/GND +Vout 4.7 µH DC DC Measure point ESR <1 Ω @ 100 kHz

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Figure 3 Measure circuit input reflected ripple Figure 4, EMC filter circuit for IEC/EN61000-4-4, IEC/EN61000-4-5 performance criteria B and EN55022 Class B Single output Dual output Recommended peripheral components to circuits in figures 4 Type Fuse Slow blow MOV Type L C1 C2 CY P20H24xxCS 2.5 A S20K30 4.7 µH 330 µF, 50 V 1 µF, 50 V 1 nF, 2 kV P20H24xxCD 2.5 A S20K30 4.7 µH 330 µF, 50 V 1 µF, 50 V 1 nF, 2 kV P20H48xxCS 1.5 A S14k60 4.7 µH 330 µF; 100 V 1 µF, 100 V 1 nF, 2 kV P20H48xxCD 1.5 A S14k60 4.7 µH 330 µF, 100 V 1 µF, 100 V 1 nF, 2 kV Page 3 of 6 MOV CY CY EMI Filter +Vin -Vin/GND +Vin Load -Vout -Vin +Vout DC DC L + Co EFT, Surge Filter Fuse MOV CY CY EMI Filter +Vin -Vin/GND +Vin Load -Vout -Vin +Vout DC DC L + Co EMS Filter Fuse + Co RL 1 µF +Vin -Vout +Vout DC DC GND CH1 -Vin/GND

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Application circuit for remote control function Application circuit for trimming function. Only for single output converter. Calculation for trim down resistor (Rtd) or trim up resistor (Rtu) Model series R1 [kΩ] R2 [kΩ] R3 [kΩ] V Ref [V] Rtd min. [kΩ] Rtu min. [kΩ] P20Hxx09CS 7.5 2.87 15 2.5 30 6.63 P20Hxx12CS 11 2.87 15 2.5 56.2 9.6 P20Hxx15CS 14.494 2.87 15 2.5 83 11.36 P20Hxx24CS 24.872 2.87 17.8 2.5 167 10 Maximum output voltage adjust range ± 10 % of Vout nominal, see min. Rtd / Rtu Trim down resistor formula Trim up resistor formula Page 4 of 6 Rtu= R2*a R2-a -R3 Vref Vout-Vref *R1 Rtd= R1*b R1-b -R3 Vref Vout-Vref *R2 +Vin -Vin/GND Ctrl 6 +Vin Load -Vout +Vout DC DC Remote control input on: 3.5 V…12 V or open Ctrl input off: 0…1.2 V -Vin/GND 1 Rtd Trim down circuit P20HxxxxCS VRef +Vout Rtu Trim up circuit P20HxxxxCS VRef +Vout 5 0V/-Vout 5 0V/-Vout

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Without heatsink With heatsink Page 5 of 6

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch Dimensions standard version Dimensions heatsink version Page 6 of 6 Pin Assignment Pin Single Dual 1 - Vin/GND - Vin/GND 2 + Vin + Vin 3 + Vout + Vout 4 Trim 0V/Com. 5 0V/-Vout - Vout

6 Rem Ctrl Rem Ctrl

PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals ! Not for resale or distribution to the general public in any way ! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 20180309 f Unit: mm Pin diameter tolerance: 0.1 mm Pin height tolerance: 0.5 mm General tolerances: 0.5 mm Unit: mm Pin diameter tolerance: 0.1 mm Pin height tolerance: 0.5 mm General tolerances: 0.5 mm