DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

  • Input + Input DC DC + Vin - Vin + Vout - Vout Cout Cin - Input + Input DC DC + Vin - Vin + Vout - Vout Cout Cout Cin

10 W DC-DC Converter P10G-Series

  • Wide 4:1 input range
  • Efficiency up to 88 %
  • Remote control on/off
  • 1500 VDC isolation
  • Continuous short circuit protection
  • Over voltage protection
  • Standard package 1” x 1”
  • MTBF > 1 Mio. hours
  • -40...+85 °C operating temperature range Model guide Type Input voltage Input current Output voltage [VDC] Output current Efficiency @ full load Capacitive load (see note 3) [µF] max. nominal [VDC] Range [VDC] no load [mA] full load [mA] minimum load [mA] maximum load [mA] [%] min. [%] typ. Single Output P10G243R3S 24 9...36 8 510 3.3 0 2400 77 79 2200 P10G2405S 24 9...36 8 510 5 0 2000 81 83 2200 P10G2409S 24 9...36 8 510 5 0 1111 84 86 680 P10G2412S 24 9...36 8 510 12 0 833 85 87 470 P10G2415S 24 9...36 8 510 15 0 667 85 87 330 P10G24245S 24 9...36 8 510 24 0 416 86 88 100 P10G483R3S 48 18...75 6 255 3.3 0 2400 77 79 2200 P10G4805S 48 18...75 6 255 5 0 2000 81 83 2200 P10G4812S 48 18...75 6 255 12 0 1111 85 87 680 P10G4815S 48 18...75 6 255 15 0 833 85 87 470 P10G4824S 48 18...75 6 255 24 0 667 86 88 330 Dual Output P10G2405D 24 9...36 8 510 ±5 0 ±1000 81 83 2 x 1000 P10G2409D 24 9...36 8 510 ±9 0 ±555 84 86 2 x 680 P10G2412D 24 9...36 8 510 ±12 0 ±416 85 87 2 x 470 P10G2415D 24 9...36 8 510 ±15 0 ±333 85 87 2 x 330 P10G2424D 24 9...36 8 510 ±24 0 ±208 85 87 2 x 100 P10G4805D 48 18...75 6 255 ±5 0 ±555 81 83 2 x 1000 P10G4812D 48 18...75 6 255 ±12 0 ±416 85 87 2 x 470 P10G4815D 48 18...75 6 255 ±15 0 ±333 85 87 2 x 330 P10G4824D 48 18...75 6 255 ±24 0 ±208 85 87 2 x 100 With suffix “K” heatsink version 1) Typical circuit The P10G series is been tested according to the following recommended test circuit before leaving the factory (see Figures 1). If you want to further decrease the input / output ripple, you can increase a capacitance values properly or choose capacitors with low ESR, but the total capacitance of the filter capacitor must not exceed the maximum load capacitance value (see Model guide table). Figure 1a Figure 1b Page 1 of 5 Recommended peripheral components to figure 1a & 1b Cin Cout P10G24xxx 100 µF, 50 V 10 µF P10G48xxx 10...47 µF, 100 V 10 µF Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch
  • Input + Input DC DC + Vin - Vin + Vout - Vout Measure point Lin 4.7 µH Cin 220 µF ESR < 1 Ω at 100 kHz Load

P10G24xxx on @ ≤ 9 VDC off @ ≥ 5.5 VDC P10G48xxx on @ ≤ 18 VDC off @ ≥ 14 VDC Filter π - type Reflected ripple current *6 P10G24xxx: P30 mAp-p, typ. P10G48xxx: P40 mAp-p, typ. Remote control theshold On state 3.5…12 VDC, or open input Off state 0…1.2 VDC Input idle current @ Off state 6… 10 mA Isolation input - output: Rated voltage (tested for 1 min.) 1500 VDC, at ≤ 1 mA Resistance > 109 Ω, measured @ 500 VDC Capacitance 1000 pF, typ. Output Voltage tolerance ± 3 %, max. Voltage cross balance (dual outputs) ± 1.5 %, max. @ balanced load Voltage cross balance (dual outputs) ± 5 %, max. @ 50 % load difference Voltage regulation ± 1 %, max @ full Vin range Temperature coefficient ± 0.03 % / °C Transient recovery time ≤ 500 µs, @ 25 % load steps Transient response deviation ≤ 5 %, @ 25 % load steps Short circuit protection Continuous, hiccup Short circuit restart Automatic Over current protection 140 % of rated current, typ. 190 % of rated current, max. Rippel & noise, BW 20MHz 80 mVp-p, max. Over voltage protection 110… 160 % of rated Vout Note: 1. Min. load should not be less than 5 %, otherwise ripple maybe increased dramatically, If the product operates under min. load, it may not be guaranteed to meet all specifications listed. Operation under minimum load will not damage the converter. 2. The recommended unbalanced load of dual output converter should be low than 5 %. If the load asymmetry greater than 5%, it may not be guaranteed to meet all specifications listed. Please contact our technical support for more details. 3. Maximum capacitive load is tested at input voltage range and full load. 4. All specifications measured at Ta 25 °C, humidity < 75 %, nominal input voltage and rated output load unless otherwise specified. 5. It is not recommended to increase the output power capability by connecting two or more converters in parallel. 6. The converters are not hot swappable Input reflected ripple measure circuit The input reflected ripple current is measured with inductor Lin and capacitor Cin to simulate source impedance. Page 2 of 5 General Start up time 10 ms, typ @ R-load Switching frequency 350 kHz, typ. Reliability Calculated MTBF MIL-HDBK-217F @ 25 °C > 1 Mio. hours EMC characteristics Radiated emissions CISPR22 / EN55022 Class A Radiated emissions,(with Fig. 2) CISPR22 / EN55022 Class B Conducted emissions CISPR22 / EN55022 Class A Conducted emissions, (with Fig. 2) CISPR22 / EN55022 Class B ESD, (with Fig. 2) EN61000-4-2 Contact ± 4 kV perf. crit. B RS EN61000-4-3 10V/m perf. crit. A EFT (with Fig. 2) EN61000-4-4 ± 2 kV perf. crit. B Surge (with Fig. 2) EN61000-4-5 ± 2 kV perf. crit. B CS EN61000-4-6 3 Vrms perf. crit. A Voltage dips, short interruptions and voltage variations immunity EN61000-4-29 0…70 % perf. crit. B Environmental Operating temperature (ambient) -40 °C to +85 °C with derating -40 °C to +65 °C at full load Storage temperature -55 °C to +125 °C Humidity 5…95 %, non condensing Cooling Free air convection Vibration 10…55 Hz, 10G, 30 min., X, Y and Z axis Physical Dimensions 25.40 x 25.40 x 11.7 mm Weight 15 g Case material Aluminium Alloy Potting Material Epoxy (UL94V-0 rated) Absolute max. ratings Pin soldering temperature 1.5 mm distance from body 300 °C for 10 sec Max. input voltage < 1 s P10G48xxx -0.7…50 VDC P10G24xxx -0.7…100 VDC Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

Figures 2, Recommended EMC circuit Single output Dual output Recommended peripheral components to circuits in figures 2 Type Fuse Time delay type MOV Type L C1 C2 CY P10G24xxS 2 A S14K35 4.7 µH 330 µF, 50 V 1 µF, 50 V 1 nF, 2 kV P10G24xxD 2 A S14K35 4.7 µH 330 µF, 50 V 1 µF, 50 V 1 nF, 2 kV P10G48xxS 1 A S14K60 4.7 µH 330 µF; 100 V 1 µF, 100 V 1 nF, 2 kV P10G48xxD 1 A S14K60 4.7 µH 330 µF, 100 V 1 µF, 100 V 1 nF, 2 kV Application remote control Page 3 of 5 Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch MOV CY CY EMI Filter +Vin 0 V +Vin Load -Vout -Vin +Vout P10GxxxxS DC DC L + Cout EMS Filter Fuse MOV CY CY EMI Filter +Vin 0 V +Vin Load -Vout -Vin +Vout P10GxxxxD DC DC L + Cout EMS Filter Fuse + Cout Com. on +Vin 0 V Load -Vout +Vout P10G-Series DC DC off Remote control input on off

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch

Dimensions Pin configuration Page 5 of 5 Pin assignment Pin Single Dual 1 - Vin - Vin 2 + Vin + Vin 3 + Vout + Vout

4 No pin Common

6 ON/OFF ctrl ON/OFF ctrl

Deutschland: Schweiz: Inselkammerstraße 10 Hochstrasse 355 D-82008 Unterhaching CH-8200 Schaffhausen Tel.: 089 614 503-10 Tel.: 052 647 42 00 E-Mail: power@hy-line.de E-Mail: power@hy-line.ch PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals ! Not for resale or distribution to the general public in any way ! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express wr itten approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 09.16 f Unit: mm Pin diameter tolerance: 0.1 mm General tolerances: 0.5 mm