OP300SL OPTEK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A 05/07 Page 1 of 4 NPN Silicon Photodarlington OP300SL Series Description: Each device in this series is a NPN silicon photodarlington in a hermetically sealed pill package with a narrow receiving angle that provides excellent on-axis coupling. Photodarlingtons are normally used in applications with low light signal levels, where more current gain is needed than phototransistors can provide. Components in the OP300 series are mechanically and spectrally matched to the OP123 and OP223 series. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data, and to Application Bulletin 202 for pill-type soldering to PCBoard. Features:

  • Narrow receiving angle
  • Variety of sensitivity ranges
  • Enhanced temperature range
  • PCBoard mounting
  • Mechanically and spectrally matched to OP123 and OP223 LEDs RoHS Pin # Sensor

1 Collector

2 Emitter

IC(ON) (mA) Min / Max Input Power EE (mW/cm2) Viewing Angle OP300SL Darlington 0.8 / NA 1.0 with 2870°K or 0.4 with 890nm 35° OP301SL 0.8 / 2.4 OP302SL 1.8 / 5.4 OP303SL 3.6 / 12.0 OP304SL 7.0 / 21.0 OP305SL 14.0 / NA Ordering Information Applications:

  • Non-contact reflective object sensor
  • Assembly line automation
  • Machine automation
  • Machine safety
  • End of travel sensor
  • Door sensor INCHES [MILLIMETERS]DIMENSIONS ARE IN:

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A 05/07 Page 2 of 4 NPN Silicon Photodarlington OP300SL Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Collector-Emitter Voltage 15.0 V Emitter-Collector Voltage 5.0 V Storage Temperature Range -65° C to +150° C Operating Temperature Range -65° C to +125° C Soldering Temperature (5 seconds with soldering iron) 260° C (1)(2) Power Dissipation 50 mW(3) Continuous Collector Current 50 mA Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS IC(ON) (4) On-State Collector Current OP300SL OP301SL OP302SL OP303SL OP304SL OP305SL 0.8 0.8 1.8 3.6 7.0 14.0 2.4 5.4 12.0 21.0 mA VCE = 5.0 V, EE = 1.0 or 0.4 mW/cm2(5) ICEO Collector-Dark Current - - 1.0 µA VCE = 10 V, EE = 0 V(BR)CEO Collector-Emitter Breakdown Voltage 15.0 - - V IC = 100 μA V(BR)ECO Emitter-Collector Breakdown Voltage 5.0 - - V I E = 100 μA VCE(SAT) (4) Collector-Emitter Saturation Voltage OP300SL, OP301SL OP302SL through OP305SL 1.1 1.1 V IC = 0.4 mA, EE = 1.0 or 0.4 mW/cm2(5) IC = 1.0 mA, EE = 1.0 or 0.4 mW/cm2(5) Notes: (1) Refer to Application Bulleting 202, which discusses proper techniques for soldering pill-type devices to PCBoards. (2) No clean or low solids. RMA flux is recommended. Durati on can be extended to 10 seconds maximum when flow soldering. (3) Derate linearly 0.5 mW/° C above 25° C. (4) Junction temperature maintained at 25° C. (5) Light source is an unfiltered tungsten bulb operating at CT = 2870° K at E E =1.0 mW/cm2 or 890nm at EE =0.4 mW/cm2 .

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A 05/07 Page 3 of 4 NPN Silicon Photodarlington OP300SL Series Collector Current vs Temperature 0.1 -60 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) IC - Typical Collector Current (mA) TEST CONDITIONS: λ - 890 nm VCE = 5 Volts Pulse Width = 100 μS Duty Cycle = 0.1% Measured 25 μS into pulse Dark Current vs Temperature 0.00 0.01 0.10 1.00 10.00 100.00 1,000.00 0 2 04 06 08 0 1 0 0 1 2 0 Ambient Temperature (°C) ICEO - Collector Current (µA) TEST CONDITIONS: VCE = 10 Volts EE = 0 Coupling Characteristics of OP123 & OP300SL 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Diatance (inches) Ralative Output Current TEST CONDITIONS: VCE = 5 Volts TA = 25 °C Typical Spectral-Response 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 600 700 800 900 1000 1100 Wavelength - nm Relative Response - % 850 nm 890 nm 935 nm

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A 05/07 Page 4 of 4 NPN Silicon Photodarlington OP300SL Series Rise & Fall Time vs. Load Resistance Load Resistance (K-W) TR & TF (mS) Rise Time Fall time TEST CONDITIONS: λ - 890 nm VCC = 5 Volts VRL = 1 Volt The light source is a pulsed LED with a rise time of less than 500 nS. The LED output is adjusted for IC = 0.8 mA. Vcc Vout Vcc FI R = LED R = 1K Ohms Switching time Circuit RLOAD Radient Intensity vs. Angular Displacement 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 - 4 0 - 3 0 - 2 0 - 1 00 1 02 03 04 0 Θ - Angular Displacement - Deg. Normalized radiant Intensity TEST CONDITIONS: λ - 890 nm VCE = 5 Volts Distance to Lens = 6" [152 mm]