DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

HYBRID IC! Hybrid IC for driving IGBT modules DESCRIPTION — M57159L-01 is a hybrid IC to drive IGBT module. This hybrid | OUTLINE DRAWING Dimensions: mm IC is driven by two power supplies and provides the required electrical isolation between the input and output with an ux opto-coupler. | < > The protection system of this hybrid IC functions with a margin of time by built-in protection circuits to maintain a reverse bias for a predetermined time after the detection of an short-current . Es Recommended IGBT modules: Voges = 600V/~150A class ql g Voces = 1200V/~75A class ay = FEATURES it H 3 + Built-in high CMR opto-coupler oe d55 e35M B.S MAX circuit) ® ® +Capability of adjusting time to control short-circuit detection +Input-output isolation voltage: 2500Vrms for imin

APPLICATIONS

To drive IGBT modules for inverter or AC servo systems application. BLOCK DIAGRAM roe eee ; @ veo CONTROL PIN FOR ter © warou Hf oerecron F> ——© | (1) DETECT PIN | TIMER & ' : RESET CIRCUIT | | prt Ppocccc4 . ot 7 ot (8) Vo ' : i | a ; j es na ' : OPTO-COUPLER GATE SHUT- (8) FAULT OUTPUT : ~ I (6) Vee Von Pin 3, 7, 9 and 10: NC

HYBRID IC! Hybrid IC for driving IGBT modules MAXIMUM RATINGS (unless otherwise noted, Ta=25°C) [-Symbor | Perameter [Condens ——~—S~dSS~CSRag CU vec _| Vee | supply voltage be a ee ae Input voltage Applied between; 13pin and 14pin | tore | output curent Pulse width 2p, f< 20kHz ae ae ee Isolation voltage Sine wave voltage 60Hz, for 1min, 2500 | to [Casetemperature Pe No condensation allowable -20- +60 No condensation allowable 25 ~ +100 [tro | Fautoutputcurrent [Inflow current at 6pin [20m Input voltage at tpin a ELECTRICAL CHARACTERISTICS (unless otherwise noted, Ta=25°C, Vcc = 15V, Vee = -10V) i | Min [Typ | Max | Recommended range [4 [is [—T[v | | 7 | —J]-to[ v | Puitup voltage on primary side | Recommended range 4.75 | 8 [5.25] V [tm | *H'inputcurent_ | Recommended range | 15.2 | 16 | 19 | ma | | __# | Switching frequency [Recommended range | = | = I 20 | ee | Recommended range laz{=|—|. | iw [inputcurent dt vwesv Cd 0 | | | "HF ouput vage nO "output voage a OD tous [UF propagatontine | wetema SSCS PO | Ins = 18mA [= ost is [ws | | ina [Ht propegetontine ——[wietema SSCS fo ft | "HHL fall ime [iw=tema Cd ff 08 Te | From protecion operation tocancel mputsanet) | 1 | — | 2 [me | | tro _| Fault output current Inflow current at pin, R = 4.7k, [—| 5 | — | ma |} Short-circuit detection When the output rises, 24 trip! | controlied time 1 pin; Min 15V, 2pin; open i Short-circuit detection When the output rises, controlled time 2 (*) pin; Min 15V, 2pin - 4pin; 1000pF Short-circuit detection voltage | Sollector voltage of the module which detects a ls[-][-[¥ | (*) The wiring length of the capacitor for changing short-circuit detection controlled time makes less than 5cm of round trip between pins 2 and 4. DEFINITION OF CHARACTERISTICS i (1) SWITCHING OPERATION (2) OPERATION OF SHORT-CIRCUIT vi | " . Vo tt vo Ws ween 90% t-——— trrip1.2 ttimer 50% 10V 10V 8pin output OV 10% TPLH {PHL Se

Hybrid IC for driving IGBT modules TYPICAL CHARACTERISTICS tein, tpH. - Ta CHARACTERISTICS teiy, tp. - Vj) CHARACTERISTICS ao 16 aa 16 Ss Vec=15V | | 3s Vec=15V | | [4 =z 147 Vee=-10V 5 146 Vee=-10V E37 | Rens. aan oe Rents. || | | =z 12/7 vin=5v =z 1?) Tex28°C na Load:CM150DY-12H re Load:CM150DY-12H ww 1.0 ww 10 Fe oot | tt | mw) Ld EE ot | | | TT dol zy 08 J ze 08 — + eee eee ° LH} asi 1] if | | | seit) 11 7 | i ssc TTT got T TT TT KX 02 & E o2 ge til] iti | | ef LI It | | | oe % 20 40 60 80 nr) 4 5 6 7 AMBIENT TEMPERATURE T, (°C) INPUT SIGNAL VOLTAGE V, (V) teipts tip2 - Ta CHARACTERISTICS tuip = Cup CHARACTERISTICS 8 8 ve | 1 1114 ve | | 11d q 7) Vee=-10V z 7} Vee= -10V = 6 5 2 6 Lt tT | | Tt TT | 55 5 Gu 5 4 Ga 4 tirip2 : Cuip=1000pF | J aa 4 rT Td 2a 7 «x 28 isco | | ge citi itt i ee FLT TT I ae tt tT tty tt RE 4 1 ey PP TET TT eo 0 0 0 20 40 60 80 C) 2000 4000 6000 8000 AMBIENT TEMPERATURE T, (°C) CONNECTIVE CAPACITANCE Crip (pF) (2pin - 4pin) POWER DISSIPATION — AMBIENT TEMPERATURE DISSIPATION CURRENT - SUPPLY VOLTAGE (MAXIMUN RATING) CHARACTERISTICS (4pin - 6pin) INPUT SIGNAL “L” BERRRRRER: eet TL \\ 20 A > tit \\ °C EP TV SON TTT REECE 3 \\ 2{] tii i fl PCOOINTT EERE Q z Bo a tLiTi”zZTT tty pS SE PLL BERR EEE 3 ot ttt i tt | 0 20 40 60 80 100 0 10 20 30 40 AMBIENT TEMPERATURE T, (°C) SUPPLY VOLTAGE (V) (4pin - 6pin) Se

Hybrid IC for driving IGBT modules OPERATION OF PROTECTION CIRCUIT (1) The protection circuit of this hybrid IC is judged to be a sort-circuit state when gate potential is high and collect voltage is high, and gate voltage is dropped immediately. Moreover, the fault sign is output (“L” level) from 8pin to indicate the protection circuit operating simultaneously. (2) In about 1 ~ 2ms after this hybrid IC detect of short-circuit, if the input sign is “L’, this hybrid IC resets from the short-circuit protection condition and then restart switching operation. ("L” period needs up to 5ys) (3) In order to secure ON time of IGBT at the time of the output (Spin) standup, short-circuit detection control time is prepared. (typical: 2.4ys) It can be adjust by connecting capacity between pins 2 and 4, OPERATION FLOW OF DETECTING SHORTCIRCUIT DETECTION OF SHORT-CIRCUIT GATE SHUTDOWN CIRCUIT OPERATE TIMER START FAULT SIGN OUTPUT 1-2ms ltteer’ 7 (lekataieeetaiatetevetate INPUT SIGNAL is “L” ow | ‘ Yes RESET (*) When the short-circuit protection circuit is operating, the output voltage is about -|Veel + 2V. i

Hybrid IC for driving |GBT modules APPLICATION CIRCUIT EXAMPLE APPLICATION EXAMPLE OF SINGLE POWER SUPPLY GY) —sh © 1 © ) M57159L 4) 5v ©) ad TUF = | vec ? M57159L. La | © " ot -® bat " @ 30V 47UF = Vee 47 pF of >) 6 Tite D-@ 1 Bat Crev f = 20kHz Voc = 15V D.F = 50% Vee = 10V Veco = 25V Vin = 5V Re = 15, Crev = 47yuF Ctrip = 0 ~ 3300pF R1=2.7k, D1: First recovery diode (trr < 0.2us) (*) Don't input the on sign til the provided (R1*Crev(s)) time is passed over after supply turn on.) PRECATION (1) Voltage compensate capacitors are provide as close as APPLICATION EXAMPLE OF HIGH POWER possible to this hybrid IC. MODULE (2) D1 requires the approximately the same voltage of power modules. CL) (3) Since very high voltage is impressed to the pin 1 when D1 is reverse-recovered, there is‘a possibility of destroying an S) internal element. As mentioned above, the protection () : measure, such as inserting a Zener diode between pins 1 @ and 6, is required. Dz a . . BV ) 3ov (4) In case pin 2 is operating, the wiring are expected to be a Ms7159L [ vet Fo 6 wired as close as possible from pin 2 and pin 4, (Standard 01 ® B Rept length: Sem and less.) © aa D-® wt fe Vee = 15V Vee = 10V Ctrip = 1000pF C1, C2 s 100pH (Low impedance) —— eee

Hybrid IC for driving IGBT modules FOR SAFETY USING Great detail and careful attention are given to the production activity of Hics, such as the development, the quality of production, and in it’s reliability. However the reliability of Hics depends not only on their own factors but also in their condition of usage. When handling Hics, please note the following cautions. CAUTIONS Packing The materials used in packing Hics can only withstand normal external conditions. When exposed to outside shocks, rain and certain environmental contaminators, the packing materials will deteriorates. Please take care in handling. Carrying 1) Don't stack boxes too high. Avoid placing heavy materials on boxes. 2) Boxes must be positioned correctly during transportation to avoid breakage. 3) Don't throw or drop boxes. 4) Keep boxes dry. Avoid rain or snow. 5) Minimal vibration and shock during transportation is desirable. Storage When storing Hics, please observe the following notices or possible deterioration of their electrical characteristics, risk of solder ability, and external damage may occur. 1) Devices must be stored where fluctuation of temperature and humidity is minimal, and must not be exposed to direct sunlight. Store at the normal temperature of 5 to 30 degrees Celsius with humidity at 40 to 60%. 2) Avoid locations where corrosive gasses are generated or where much dust accumulates. 3) Storage cases must be static proof. 4) Avoid putting weight on boxes. Extended storage When extended storage is necessary, Hics must be kept non-processed. When using Hics which have been stored for more than one year or under severe conditions, be sure to check that the exterior is free from flaw and other damages. Maximum ratings To prevent any electrical damages, use Hics within the maximum ratings. The temperature, current, voltage, etc. must not exceed these conditions. Polarity To protect Hics from destruction and deterioration due to wrong insertion, make sure of polarity in inserting leads into the board holes, conforming to the external view for the terminal arrangement.

Hybrid IC for driving IGBT modules Marketing division, Marketing planning department 6-41 Tsukuba, Isahaya, Nagasaki, 854-0065 Japan Keep Safety first in your circuit designs! “ISAHAYA Electronics Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (1) placement of substitutive, auxiliary, (2) use of non-farmable material or (3) prevention against any malfunction or mishap. Notes regarding these materials “These materials are intended as a reference to our customers in the selection of the ISAHAYA products best suited to the customer's application; they don't convey any license under any intellectual property rights, or any other rights, belonging ISAHAYA or third party. -ISAHAYA Electronics Corporation assumes no responsibility for any damage, or infringement of any third party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. ‘All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by ISAHAYA Electronics Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for the latest product information before purchasing product listed herein. -ISAHAYA Electronics Corporation products are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact ISAHAYA electronics corporation or an authorized ISAHAYA products distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. <The prior written approval of ISAHAYA Electronics Corporation is necessary to reprint or reproduce in whole or in part these materials. ‘If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or re-export contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. ‘Please contact ISAHAYA Electronics Corporation or authorized ISAHAYA products distributor for further details on these materials or the products contained therein. el 7 May.2004