YS051DS-05B ISAHAYA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
HYBRID IC FOR ON-BOARD POWER SUPPLY PRELIMINARY Notice: This is not a final specification Some parametric limits are subject to change
DESCRIPTION
The YS051DS-05B is a thin-profile and lightweight single-output DC-DC converter. Its output power is 1.5W and the input is insulated from the output. With an over-current protection circuit built-in, the YS051DS-05B is an optimum solution for onboard power supplies in FA, OA, and control equipment.
FEATURES
Input voltage range: 4.5 to 5.5V DC Output: +5V, 300mA (output power: 1.5W) Thin-profile and lightweight design Insulation between input and output: 500V DC, 1min Built-in over-current protection circuit
APPLICATIONS
Best suited to onboard power supplies in FA, OA, and control equipment. OUTLINE DRAWING D i m e n s i o n s : m m 20.7 XXB-XXXX 24.0 10.0 Pin No. BLOCK DIAGRAM -Vo +Vo1 LC FILTER OV ER- CURRENT PROTECTION CIRCUIT OPTOCOUPLER LC FILTER CONSTANT- VOLTAGE CIRCUIT -VIN +VIN BASE DRIVER
HYBRID IC FOR ON-BOARD POWER SUPLY PRELIMINARY Notice: This is not a final specification Some parametric limits are subject to change MAXIMUM RATINGS (unless otherwise noted, Ta=25°C) Symbol Parameter Conditions Ratings Unit VIN Input voltage Between: pins 4 and 1 5.5 V IO Output current Between pins 4 and 3 300 mA PO Output power — 1.5 W Topr Operating temperature No condensation (*1) -10 ~ +70 °C Tstg Storage temperature No condensation -20 ~ +85 °C Viso Input-output isolation voltage DC, 1min 500 V (*1) Please refer to derating curve. ELECTRICAL CHARACTERISTICS (unless otherwise noted, VIN=5V, Ta=25°C) Limits Symbol Parameter Test conditions MIN. TYP. MAX. Unit VIN Input voltage Recommended range 4.5 5.0 5.5 V VO Output voltage I O=0 ~ 300mA 4.75 5.0 5.25 V Reg-I Input regulation I O=300mA, VIN=4.5 ~ 5.5V — — 50 mV Reg-L Load regulation I O=0 ~ 300mA — — 50 mV VP-P Ripple voltage I O=300mA — — 50 mV η Efficiency I O=300mA — 63 — % TEST CIRCUIT DIAGRAM VO 1 2 VYS051DS-05BVIN IO
HYBRID IC FOR ON-BOARD POWER SUPLY PRELIMINARY Notice: This is not a final specification Some parametric limits are subject to change TYPICAL CHARACTERISTICS INPUT CURRENT - INPUIT VOLTAGE CHARACTERISTICS 100 200 300 400 500 600 700 800 INPUT VOLTAGE V IN (V) INPUT CURRENT IIN (mA) RL = 33.3Ω (IO = 150mA) RL = 16.7Ω (IO = 300mA) Ta = 25°C OUTPUT VOLTAGE - OUTPUT CURRENT CHARACTERISTICS (VO) 0.0 1.0 2.0 3.0 4.0 5.0 6.0 0 100 200 300 400 OUTPUT CURRENT I O (mA) OUTPUT VOLTAGE VO (V) VIN = 5.0V Ta = 25°C EFFICIENCY - OUTPUT CURRENT CHARACTERISTICS 100 0 100 200 300 400 OUTPUT CURRENT I O (mA) EFFICIENCY η (%) VIN = 5.0V Ta = 25°C EFFCIENCY - INPUT VOLTAGE CHARACTERISTICS 100 INPUT VOLTAGE VIN (V) EFFICIENCY η (%) IO =300mA Ta = 25°C OUTPUT VOLTAGE - INPUT VOLTAGE CHARACITERISTICS 0.0 1.0 2.0 3.0 4.0 5.0 6.0 INPUT VOLTAGE V IN (V) OUTPUT VOLTAGE VO (V) RL = 16.7Ω (IO = 300mA) Ta = 25°C RL = 33.3Ω (IO = 150mA) DERATING CHARACTERISTICS 100 150 200 250 300 350 - 1 0 1 03 05 07 09 0 1 1 0 OPERATING TEMPERATURE (°C) OUTPUTCURRENT IO (mA)
HYBRID IC FOR ON-BOARD POWER SUPLY PRELIMINARY Notice: This is not a final specification Some parametric limits are subject to change FOR SAFETY USINGç ç Great detail and careful attention are given to the production activity of Hics, such as the development, the quality of production, and in it’s reliability. However the reliability of Hics depends not only on their own factors but also in their conditi on of usage. When handling Hics, please note the following cautions. CAUTIONS Packing Carrying Storage Extended storage Maximum ratings Polarity ç The materials used in packing Hics can only withstand normal external conditions. When exposed to outside shocks, rain and certain environmental contaminators, the packing materials will deteriorates. Please take care in handling. ç 1) Don’t stack boxes too high. Avoid placing heavy materials on boxes. 2) Boxes must be positioned correctly during transportation to avoid breakage. 3) Don't throw or drop boxes. 4) Keep boxes dry. Avoid rain or snow. 5) Minimal vibration and shock during transportation is desirable. When storing Hics, please observe the following notices or possible deterioration of their electrical characteristics, risk of solderability, and external damage may occur. 1) Devices must be stored where fluctuation of temperature and humidity is minimal, and must not be exposed to direct sunlight. Store at the normal temperature of 5 to 30 degrees Celsius with humidity at 40 to 60%. 2) Avoid locations where corrosive gasses are generated or where much dust accumulates. 3) Storage cases must be static proof. 4) Avoid putting weight on boxes. When extended storage is necessary, Hics must be kept non-processed. When using Hics which have been stored for more than one year or under severe conditions, be sure to check that the exterior is free from flaw and other damages. To prevent any electrical damages, use Hics within the maximum ratings. The temperaqture, current, voltage, etc. must not exceed these conditions. To protect Hics from destruction and deterioration due to wrong insertion, make sure of polarity in inserting leads into the board holes, conforming to the external view for the terminal arrangement.
HYBRID IC FOR ON-BOARD POWER SUPLY PRELIMINARY Notice: This is not a final specification Some parametric limits are subject to change ççççççççççççççççççççççççç çç çç Marketing division, Marketing plannning department 6-41 Tsukuba, Isahaya, Nagasaki, 854-0065 Japan Nov.2002 Keep safety first in your circuit designs! ççɾ ISAHAYA Electronics Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropreate measures such as (1)placement of substitutive, auxiliary circuits, (2)use of non-flammable material or (3)prevention against any malfunction or mishap. Notes regarding these materials ççɾ These materials are intended as a reference to our customers in the selection of the ISAHAYA products best suited to the customer's application; they don't convey any license under any intellectual property rights, or any other rights, belong ing to ISAHAYA Electronics Corporation or a third party. ɾISAHAYA Electronics Corporation assumes no responsibility for any damage, or infringement of any third party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials . ɾAll information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by ISAHAYA Electronics Coporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact ISAH AYA Electronics Corporation or an authorized ISAHAYA products distributor for the latest product infomation before purchasing a product listed herein. ɾISAHAYA Electronics Corporation products are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact ISAH AYA Electronics Corporation or an authorized ISAHAYA products distributor when considering the use of a product contained herein for any specific perposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. ççɾ The prior written approval of ISAHAYA Electronics Corporation is necessary to reprint or reproduce in whole or in part these m a t e r i a l s . ççɾ If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. ççɾ Please contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for further details on these materials or the products contained therein. çç