N2000-96-12

N1500 ARTESYN | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

OUTPUT SPECIFICATIONS (2) Voltage adjustability Accessible at front panel ±10% Remote sense Open/reverse sense lead protection Compensates for voltage drop of up to 0.5V to the load Regulation, line or load All outputs, NL-FL ±0.2%; at nominal line or all 10mV min. line variations at FL Cross regulation 0.2% max. or 10mV between outputs Overshoot/undershoot None at turn-on/off Transient response Main output ≤2.0% max. dev., 25% step load ≤200µs recovery change at 1A/µs to 1.0% Temperature coefficient ±0.02%/°C Ripple and noise 0Hz to 20MHz 50mV pk-pk or 1.0% Overvoltage protection Reset by cycling AC 115 to 130% of nominal Overload protection 105-115% full load Short circuit protection All outputs Auto recovery Thermal protection Auto shutdown, AC reset Current sharing ±5.0% 50% to 100% load Current monitor (V1) 5VDC at full load ±0.5V INPUT SPECIFICATIONS Input voltage range 180 to 264VAC Input frequency range 47Hz to 63Hz Input surge current Meets IEEE std. 587.1980; 3KV ring wave Input current 230VAC, 2000W 13A Power factor 230VAC, 2kW load 0.98 min. Power up time Full load 1.0s max. EMC CHARACTERISTICS Radiated emissions EN55022/11, FCC part 15 Level A Conducted emissions EN55022/11, FCC part 15 Level A Harmonic distortion EN61000-3-2 Conforms Electrostatic discharge EN61000-4-2 Level 3 RF field susceptibility EN61000-4-3 Level 3 transients/bursts Surge susceptibility EN61000-4-5 Level 3 GENERAL SPECIFICATIONS Hold-up time 180VAC, 2kW load 15ms min. Efficiency 230VAC, full load 73% Isolation voltage Input/output 3000VAC Input/chassis 1500VAC Output/output 500VAC Switching frequency 100kHz Approvals and EN60950, UL1950, standards CSA C22.2 No. 950 Weight 6.9kg (15Ibs) Size 5 x 8 x 11 inches 127 x 203.2 x 279.4 mm MTBF per MIL-HDBK-217E 100,000 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient 0°C to +50°C Non-operating -15°C to +85°C Cooling 60CFM Internal DC ball bearing fan Relative humidity Non-condensing 0% to 95% RH Altitude Operating 6,000 feet max. Non-operating 55,000 feet max. Vibration 5Hz to 500Hz 2.4G rms peak N1500 and N2000 SERIES Single, and dual output [ 2 YEAR WARRANTY ]

• Active harmonic correction to EN61000-3-2
• 180VAC to 264VAC input voltage range
• Flexible output voltage configuration
• Two output power ratings
• Forced current sharing, all outputs
• DC OK (including LED)
• UL, CSA and TÜV safety approvals
• Industry standard 5 x 8 x 11 inch footprint The N1500 and N2000 series are a range of system-orientated, single or dual output power supplies with output powers of 1500W and 2000W. Harmonically corrected, they operate from 180VAC to 264VAC. World wide safety approvals are standard. Fan cooled and enclosed in the industry standard 5 x 8 x 11 inch form, the N1500 and N2000 series are an ideal choice when the economy and predictable performance of a centralized system power supply are desired. By utilizing dual high current converters, operating independently or together, a wide variety of output voltage and current combinations can be factory configured. The N1500 and N2000 extend the range of the N1000 family. Forced current share provides higher current to satisfy needs in large systems, or to power expansion chassis. Dual output models at 5VDC/12VDC are perfect to power mass storage systems. Other applications might use 5VDC/3.3VDC, both operating at high currents. Single output versions, operating alone or in redundant mode provide an economic power source for distributed systems. System interface signals include AC and DC good, current monitor (V1). OVP , OCP , overtemperature protection, remote enable, margin check inhibit as standard. By combining robust performance and broad range, the N1500 and N2000 series sets the standard for centralized system power supplies. SPECIFICATION All specifications are typical at nominal input, full load at 25 ° C unless otherwise stated PAGE 1

MAX. OUTPUT OUTPUT V1 OUTPUT V2 MODEL NUMBERPOWER (1) VOLTAGE/CURRENT VOLTAGE/CURRENT 1500W 3.3V @ 300A N1500-96-9 1500W 5.0V @ 300A N1500-96-1 1500W 12V @ 125A N1500-96-2 1500W 24V @ 62A N1500-96-4 1500W 28V @ 54A N1500-96-5 1500W 48V @ 31A N1500-96-6 1500W 5.0V @ 200A 12V @ 50A N1500-96-12 1500W 5.0V @ 200A 24V @ 24A N1500-96-14 2000W 5.0V @ 360A N2000-96-1 2000W 12V @ 150A N2000-96-2 2000W 24V @ 83A N2000-96-4 2000W 28V @ 71A N2000-96-5 2000W 48V @ 42A N2000-96-6 2000W 5.0V @ 240A 12V @ 66A N2000-96-12 2000W 5.0V @ 240A 24V @ 33A N2000-96-14 2000W 5.0V @ 240A 3.3V @ 120A N2000-96-19 International Safety Standard Approvals VDE0805/EN60950/IEC950 File No. R917062 Certificate No. R9172062 UL1950 File No. E135734 CSA C22.2 No. 950 Bulletin No. 1402C TÜV 1500 and 2000 Watt AC/DC high wattage power supplies with PFC MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES | 1500-2000W AC/DC PAGE 2http://www.artesyn.com

PIN NO. J1 J2 1 + Sense (V1) (4) + Sense (V2)

2 Current Monitor (V1) (5) - Sense (V2)

3 Inhibit (5) Current Share (V2)

4 - Sense (V1) (4) Inhibit (5)

5 No Connection N/A

6 No Connection N/A

7 Current Share (5) N/A

8 Remote Adj. (V1) (6) N/A

9 AC Good (5) N/A

10 Chassis Ground N/A

11 Logic Ground N/A

12 Margin (7) N/A

13 No Connection N/A

14 DC OK (5,8) N/A

1 1500W or 2000W max. power. All outputs isolated. 2 Specifications refer to all outputs except as noted (V1). 3 Signal referenced to V1 output neg. sense trim. 4 Use 20AWG or larger twisted pair. 5 Reference to Logic Ground (Pin J1-J11). 6 See Figure 4. 7 See Figure 3. 8 See Figure 5. Mechanical notes A AC connector is 3 position terminal block (#8 screws included), mating to #8 ring tongue terminal. B DC output is 5/16-18 studs mating to 5/16 terminal lugs. C J-1 signal connector is Molex 39-30-1140 or equivalent. Mating connector is Molex 39-01-2140 or equivalent. D J-2 signal connector is Molex 39-01-1120 or equivalent. Mating connector is 39-01-2120 or equivalent. E Signal connector contacts are Molex 39-00-0039 or equivalent. F TB1 and J2 are not installed on single output models. G Alternate I/O configurations are available. Please consult factory for further details. 5.00 (127.0) 12.13 Max. (308.10) ALL DIMENSIONS IN INCHES (mm) 6.750 (171.450) 11.00 (279.40) 0.75 (19.05) 4.00 (101.60) 0.50 (12.7) 5.75 (146.05) 1.13 (28.70) 8.00 (203.2) AIRFLOW 0.90 (22.86) 1.30 (33.02) 8-32 x 0.29 (7.37) Deep (4) Top and Bottom 2.80 (71.12) 8-32 x 0.29 (7.37) Deep (4) Both Sides PIN 1 Main Output 5/16 - 18 Studs 50 IN-LB Torque Max. AC Input (# 8 Screws) 0.90 (22.86) 0.90 (22.86) 1.00 (25.40) ACH ACN PAGE 3 1500 and 2000 Watt AC/DC high wattage power supplies with PFC 1500-2000W AC/DC | MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES

10K Output Voltage Sense FIG. 4 (J1-P8) J1-P9 AC Good, J1-P14 DC OK Low = Power/Output fail High = Power/Output OK External Pull-up Required Sink Current 20mA (On Voltage 0.7V) FIG. 2 (Ref. FIG 5) 15V 10K J1-P3 Close to Enable FIG. 1 Open = Nominal Voltage Tie to +5V for High Margin Tie to Logic Ground (J1-11) For Low Margin. (J1-P12) Margin FIG. 3 STANDARD CONTROL SIGNALS Remote enable See Figure 1 DC OK Signal remains "Hi" as long as (See Figures 2 and 5) output is ±5.0% of nominal. AC power fail signal Signal "Hi" when AC >170VAC and (See Figure 5) "Lo" when <150VAC. Margin Hi/Lo (V1) Allows ±5.0% change in output (See Figure 3) for system margin checking. Remote Adjust The outputs may be remotely (See Figure 4) adjusted linearly ±10%. Current Monitor Analog signal indicates load current in single or parallel operation. 5±0.5VDC represents FL, resistive load 10 3kΩ . >10ms AC Power Fail Signal/DC OK Timing AC Input Voltage 170Vrms >5ms AC Good Flag DC Outputs DC Good Flag FIG. 5 1500 and 2000 Watt AC/DC high wattage power supplies with PFC MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES | 1500-2000W AC/DC PAGE 4http://www.artesyn.com DS_N1500/N2000_19980401.PDF