MK31VT432 OKI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

MK31VT432-10YCÑ98.07.21Ò Page 1/11 Semiconductor MK31VT432-10YC 4,194,304 Word x 32 Bit SYNCHRONOUS DYNAMIC RAM MODULE (1BANK):

DESCRIPTION

The Oki MK31VT432-10YC is a fully decoded, 4,194,304 x 32bit synchronous dynamic random access memory composed of two 64Mb DRAMs (4Mx16) in TSOP packages mounted with decoupling capacitors on a 100-pin glass epoxy Dual-in-Line Package supports any application where high density and large capacity of storage memory are required, like for example PCs or servers.

FEATURES

4-Meg Word x 32-Bit (1Bank 4 Byte) organization 100-pin Dual Inline Memory Module 10Ω Damping Resister for DQ and CLK Pins Single 3.3V power supply, ±0.3V tolerance Input :LVTTL compatible Output :LVTTL compatible Refresh : 4,096 cycles/64 ms Programmable data transfer mode

  • /CAS latency (2, 3)
  • Burst length (2, 4, 8)
  • Data scramble(sequential, interleave) /CAS before /RAS auto-refresh, Self-refresh capability Serial Presence Detect (SPD) With EEPROM PRODUCT ORGANIZATION Operation Access Time (Max.) Product Name Frequency (Max.) tAC2 tAC3 MK31VT432 - 10YC

100 MHz

13.0ns 9.0ns Note. Specification are subject to change without notice.

MK31VT432-10YCÑ98.07.21Ò Page 2/11 BLOCK DIAGRAM CLK0 CLK1 /CS0 CKE0 DQMB0 DQMB1 DQ0 DQ7 DQ24 DQ31 DQMB3 UDQM DQ16 DQ23 DQMB2 DQ0 DQ7 LDQM CKE /CS DQ8 DQ15 Vcc Vss SDRAMs 0.22µF x2 /RAS,/CAS,/WE A0-A11,BA0,BA1 á SCL SDA A0 A1 Serial PD 10pF DQ15 DQ8 UDQM LDQM CKE /CS DQ0 DQ7 DQ15 DQ8 SA0 SA1 SA2 10pF Note. The Value of all resistors is 10Ω . MODULE OUTLINE (Front) (Back) 100

MK31VT432-10YCÑ98.07.21Ò Page 3/11 PIN CONFIGURATION Front side Back side Front side Back side Pin No. Pin name Pin No. Pin name Pin No. Pin name Pin No. Pin name VSS VSS VSS VSS DQ0 DQ8 CKE0 NC DQ1 DQ9 /WE NC DQ2 DQ10 /CS0 NC DQ3 DQ11 /CS2 NC VCC VCC VCC VCC DQ4 DQ12 NC NC DQ5 DQ13 NC NC DQ6 DQ14 NC NC DQ7 DQ15 NC NC DQMB0 DQMB1 VSS VSS VSS VSS DQMB2 DQMB3 DQ16 DQ24 DQ17 DQ25 DQ18 DQ26 DQ19 DQ27 VCC VCC A10 BA0 DQ20 DQ28 BA1 A11 DQ21 DQ29 NC NC DQ22 DQ30 VCC VCC DQ23 DQ31 NC /RAS VSS VSS NC /CAS SDA SA0 NC NC SCL SA1 CLK0 CLK1 VCC 100 SA2 Pin Name Function Pin Name Function VCC Power Supply (3.3V) /WE Write Enable VSS Ground (0V) DQMB# Data Input / Output Mask CLK# System Clock DQ# Data Input / Output /CS# Chip Select SDA Data I/O for SPD CKE# Clock Enable SCL CLK input for SPD A0-A11 Address SA# Socket Position Address for SPD BA0, BA1 Bank Select Address NC No Connection /RAS Row Address Strobe /CAS Column Address Strobe

MK31VT432-10YCÑ98.07.21Ò Page 4/11 SERIAL PRESENCE DETECT Byte No. SPD Hex Value Remark Notes Defines the number of bytes written into 128 byte SPD memory Total number of bytes of SPD memory 256 byte Fundamental memory type SDRAM Number of rows 12 rows Number of columns 8 columns Number of module banks 1 bank Data width of this assembly 32 bits ... Data width continuation Voltage interface level LVTTL Cycle time (CL=3) CL=3 tCC=10ns Access time from CLK (CL=3) CL=3 tAC3=9ns DIMM configuration type None Parity Refresh rate / type Normal / Self Primary SDRAM width x16 Error checking SDRAM width Minimum CLK delay tCCD: 1 CLK Burst lengths supported 2, 4, 8 Number of banks on each SDRAM 4 banks /CAS latency 2, 3 /CS latency /WE latency SDRAM module attributes SDRAM device attributes : General Cycle time (CL=2) CL=2 tCC2=15ns Access time from CLK (CL=2) CL=2 tAC2=9ns Cycle time (CL=1) Not support Access time from CLK (CL=1) Not support Minimum ROW pulse width tRP=30ns /RAS to /RAS bank delay tRRD=20ns /RAS to /CAS delay tRCD=30ns Minimum /RAS precharge time tRAS=60ns Density of each bank on module 16MB Command and address signal input setup time 3ns Command and address signal input hold time 1ns Data signal input setup time 3ns Data signal input hold time 1ns 36-61 00-00 Superset Information R.F.U SPD data revision code Checksum for byte 0-62 64-71 Manufacturer’s JEDEC ID code Manufacturing location 73-90 Manufacturer’s part number MK31VT432-10YC 91, 92 20, 20 Revision code 93-125 00-00 R.F.U 126 Intel specification frequency 66MHz 127 Intel specification /CAS latency CL=2,3 128-255 FF-FF Unused storage locations

MK31VT432-10YCÑ98.07.21Ò Page 5/11

ELECTRICAL CHARACTERISTICS

Voltage on any pin relative to Vss VIN, VOUT -0.5 to Vcc+0.5 V Vcc supply voltage Vcc, VccQ -0.5 to 4.6 V Storage temperature Tstg - 55 to 150 Power dissipation PD* W Short circuit current IOS mA Operating temperature Topr 0 to 70 *: Ta=25°C Recommended Operating Conditions (Voltages referenced to Vss = 0V) Parameter Symbol Min. Typ. Max. Unit Power supply voltage Vcc, VccQ 3.0 3.3 3.6 V Input high voltage VIH 2.0 Vcc+0.3 V Input low voltage VIL -0.3 0.8 V Capacitance (Vcc=3.3V ± 0.3V, Ta=25 °C f=1MHz) Parameter Symbol Max. Unit Input capacitance (A0-A11, BA0, BA1, /RAS, /CAS, /WE) CIN1 pF Input capacitance (/CS0,/CS2) CIN2 pF Input capacitance (DQMB0-DQMB3) CIN3 pF Input capacitance (CKE0) CIN4 pF I/O capacitance (DQ0-DQ32) CI/O pF Input capacitance (CLK0) CCLK pF

MK31VT432-10YCÑ98.07.21Ò Page 6/11 DC CHARACTERISTICS (Vcc=3.3V ± 0.3V, Ta = 0 to 70 °C) Condition Module Spec. Parameter Symbol CKE Others Min. Max. Unit Note Output High Voltage VOH IOH = -2.0mA 2.4 V Output Low Voltage VOL IOL = 2.0mA 0.4 V Input Leakage Current ILI -20 µA Output Leakage Current ILO -10 µA Average Power Supply Current (Operating) ICC1 CKE ≥ VIH tCC=min. tRC=min. No Burst 290 mA 1, 2 Power Supply Current (Stand by) ICC2 CKE ≥ VIH tCC=min. mA Average Power Supply Current (Clock Suspension) ICC3S CKE ≤ VIL tCC=min. mA Average Power Supply Current (Active Stand by) ICC3 CKE ≥ VIH, /CS ≥ VIH tCC=min. 190 mA Power Supply Current (Burst) ICC4 CKE ≥ VIH tCC=min. 420 mA 1, 2 Power Supply Current (Auto-Refresh) ICC5 CKE ≥ VIH tCC=min. tRC=min. 370 mA Average Power Supply Current (Self-Refresh) ICC6 CKE ≤ 0.2V tCC=min. mA Average Power Supply Current (Power down) ICC7 CKE ≤ VIL tCC=min. mA Notes: 1. Measured with the output open. 2. Address and data can be changed once or not be changed during one cycle. 3. Address and data can be changed once or not be changed during two cycle. MODE SET ADDRESS KEYS /CAS Latency Burst Type Burst Length CL BT BT=0 BT=1 Reserved Sequential Reserved Reserved Reserved Interleave Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Note: A7, A8, A10, A11, BA0, BA1 and All should stay "L" during mode set cycle.

MK31VT432-10YCÑ98.07.21Ò Page 7/11 POWER ON SEQUENCE 1. With inputs in NOP state, turn on the power supply and enter the system clock. 2. After the VCC voltage has reached the specified level, take a pause of 200µs or more with the input being NOP. 3. Enter the precharge all bank command. 4. Apply CBR auto-refresh eight or more times. 5. Enter the mode register setting command.

MK31VT432-10YCÑ98.07.21Ò Page 8/11 AC CHARACTERISTIC (Vcc=3.3V ± 0.3V, Ta = 0 to 70 °C) NOTE 1, 2 Module Spec. Parameter Symbol Min. Max. Unit Note Clock Cycle Time CL=3 tCC ns CL=2 ns Access Time from Clock CL=3 tAC ns 3, 4 CL=2 ns 3, 4 Clock "H" Pulse Time tCH ns Clock "L" Pulse Time tCL ns Input Hold Time tHI ns Output Low Impedance Time from Clock tOLZ ns Output High Impedance Time from Clock tOHZ ns Output Hold from Clock tOH ns /RAS Cycle Time tRC 100 ns /RAS Precharge Time tRP ns /RAS Active Time tRAS 100,000 ns /RAS to /CAS Delay Time tRCD ns Write Recovery Time tWR ns /RAS to /RAS Bank Active Delay Time tRRD ns Refresh Time tREF ms Power-down Exit Set-up Time tPDE tSI+1CLK ns Input Level Transition Time tT ns /CAS to /CAS Delay Time (Min) ICCD Cycle Clock Disable Time from CKE ICKE Cycle Data Output High Impedance Time from IDOZ Cycle Data Input Mask Time from DQMB IDOD Cycle Data Input Time from Write Command IDWD Cycle Data Output High Inpedance Time from Precharge Command IROH Cycle Active Command Input Time from MODE IMRD Cycle Write Command Input Time from Output tOWD Cycle NOTES: 1) AC measurements assume tT=1ns. 2) The reference level for timing of input signals is 1.4V. 3) This parameter is measured with a load circuit equivalent to 1 TTL load and 50pF (RLoad is 50ohm). 4) An access time is measured at 1.4V. 5) If tT is longer than 1ns, the reference level for timing of input signals are VIH and VIL. OUTPUT 50pF OUTPUT LOAD CONDITION 50Ω 1.4v

MK31VT432-10YCÑ98.07.21Ò Page 9/11 FUNCTION TRUTH TABLE (Table1) (1/2) Current State /CS /RAS /CAS /WE BA ADDR Action Idle H X X X X X NOP L H H H X X NOP L H H L BA X ILLEGAL 2 L H L X BA CA ILLEGAL 2 L L H H BA RA Row Active L L H L BA A10 NOP 4 L L L H X X Auto-Refresh or Self-Refresh 5 L L L L L OP Code Mode Register write Row Active H X X X X X NOP L H H X X X NOP L H L H BA CA, A10 Read L H L L BA CA, A10 Write L L H H BA RA ILLEGAL 2 L L H L BA A10 Precharge L L L X X X ILLEGAL Read H X X X X X NOP (Continue Row Active after Burst ends) L H H H X X NOP (Continue Row Active after Burst ends) L H H L BA X Reserved L H L H BA CA, A10 Term Burst, start new Burst Read 3 L H L L BA CA, A10 Term Burst, start new Burst Write 3 L L H H BA RA ILLEGAL 2 L L H L BA A10 Term Burst, execute Row Precharge L L L X X X ILLEGAL Write H X X X X X NOP (Continue Row Active after Burst ends) L H H H X X NOP (Continue Row Active after Burst ends) L H H L BA X Reserved L H L H BA CA, A10 Term Burst, start new Burst Read 3 L H L L BA CA, A10 Term Burst, start new Burst Write 3 L L H H BA RA ILLEGAL 2 L L H L BA A10 Term Burst, execute Row Precharge 3 L L L X X X ILLEGAL Read with H X X X X X NOP (Continue Burst to End and enter Row Precharge) Auto Precharge L H H H X X NOP (Continue Burst to End and enter Row Precharge) L H H L BA X ILLEGAL 2 L H L H BA CA, A10 ILLEGAL 2 L H L L X X ILLEGAL L L H X BA RA, A10 ILLEGAL 2 L L L X X X ILLEGAL Write with H X X X X X NOP (Continue Burst to End and enter Row Precharge) Auto Precharge L H H H X X NOP (Continue Burst to End and enter Row Precharge) L H H L BA X ILLEGAL 2 L H L H BA CA, A10 ILLEGAL 2 L H L L X X ILLEGAL L L H X BA RA, A10 ILLEGAL 2 L L L X X X ILLEGAL

MK31VT432-10YCÑ98.07.21Ò Page 10/11 FUNCTION TRUTH TABLE (Table1) (2/2) Current State /CS /RAS /CAS /WE BA ADDR Action Precharge H X X X X X NOP Æ Idle after tRP L H H H X X NOP Æ Idle after tRP L H H L BA X ILLEGAL 2 L H L X BA CA ILLEGAL 2 L L H H BA RA ILLEGAL 2 L L H L BA A10 NOP 4 L L L X X X ILLEGAL Write H X X X X X NOP Recovery L H H H X X NOP L H H L BA X ILLEGAL 2 L H L X BA CA ILLEGAL 2 L L H H BA RA ILLEGAL 2 L L H L BA A10 ILLEGAL 2 L L L X X X ILLEGAL Row Active H X X X X X NOP Æ Row Active after tRCD L H H H X X NOP Æ Row Active after tRCD L H H L BA X ILLEGAL 2 L H L X BA CA ILLEGAL 2 L L H H BA RA ILLEGAL 2 L L H L BA A10 ILLEGAL 2 L L L X X X ILLEGAL Refresh H X X X X X NOP Æ Idle after tRC L H H X X X NOP Æ Idle after tRC L H L X X X ILLEGAL L L H X X X ILLEGAL L L L X X X ILLEGAL Mode Resister H X X X X X NOP Access L H H H X X NOP L H H L X X ILLEGAL L H L X X X ILLEGAL L L X X X X ILLEGAL ABBREVIATIONS RA = Row Address BA = Bank Address NOP = No Operation command CA = Column Address AP = Auto Precharge Notes: 1. All inputs will be enabled when CKE is set high for at least 1 cycle prior to the inputs. 2. Illegal to bank in specified state, but may be legal in some cases depending on the state of bank selection. 3. Satisfy the timing of ICCD and tWR to prevent bus contention. 4. NOP to bank precharging or in idle state. Precharges activated bank by BA or A10. 5. Illegal if any bank is not idle.

MK31VT432-10YCÑ98.07.21Ò Page 11/11 FUNCTION TRUTH TABLE (CKE) (Table2) Current State(n) CKEn-1 CKEn /CS /RAS /CAS /WE ADDR Action Self Refresh H X X X X X X INVALID L H H X X X X Exit Self Refresh Æ ABI L H L H H H X Exit Self Refresh Æ ABI L H L H H L X ILLEGAL L H L H L X X ILLEGAL L H L L X X X ILLEGAL L L X X X X X NOP (Maintain Self Refresh) Power Down H X X X X X X INVALID L H H X X X X Exit Power Down Æ ABI L H L H H H X Exit Power Down Æ ABI L H L H H L X ILLEGAL L H L H L X X ILLEGAL L H L L X X X ILLEGAL 6 L L X X X X X NOP (Continue power down mode) All Banks idle 6 H H X X X X X Refer to Table 1 (ABI) H L H X X X X Enter Power Down H L L H H H X Enter Power Down H L L H H L X ILLEGAL H L L H L X X ILLEGAL H L L L H L X ILLEGAL H L L L L H X Enter Self Refresh H L L L L L X ILLEGAL L L X X X X X NOP Any State H H X X X X X Refer to Operations in Table 1 Other than H L X X X X X Begin Clock Suspend Next Cycle Listed Above L H X X X X X Enable Clock of Next Cycle L L X X X X X Continue Clock Suspension Notes: 6. Power-down and self refresh can be entered only when all the banks are in an idle state.